Controllable direct-syntheses of delaminated MWW-type zeolites

A method for the direct syntheses of partially and fully delaminated MWW zeolites is reported herein.Two organic amines were introduced into the hydrothermal synthetic system:hexamethyleneimine(HMI),which acted as the structure-directing agent for the MWW layered structure;and dicyclohexylamine(DCHA),in the role of an in-situ delaminating agent.By varying the amount of DCHA,partially and fully delaminated MWW zeolites having two MWW structure layers and one single layer,respectively,were obtained.These were denoted as SCM-1(Sinopec Composite Material)and SCM-6,respectively.The delaminated materials possess ultra-large external surface areas,and the transmission electron microscopy images illustrated their layered nature.In the reaction of liquid phase benzene alkylation with ethylene,SCM-1,the double-layered MWW zeolite,exhibited far superior catalytic performance compared to zeolite MCM-22.

Colloid of Delaminated Layered Double Hydroxides:a Novel Type of LDH-based Catalyst

The colloid of delaminated layered double hydroxides(LDHs), a new LDH-based catalyst, is described. The semi-heterogeneous delaminated colloidal MgPdA1-LDH, in which the total surface of catalytic site-bearing lamellae was rendered accessible for chemical reactivity, showed excellent catalysis toward Suzuki reaction. The turnover frequency of this catalyst for Suzuki reaction between bromobenzene and phenylboronic acid is about 8000 h^-1.

Analysis of energy release rate for composite delaminated cylindrical shells subjected to axial compression

In this paper, the postbuckling governing equations and the analytical expression of the energy release rates associated with delamination growth in a compression-loaded cylindrical shell are derived by using the variational principle of moving boundary and the Griffith fracture criterion. The finite difference method is used to generate the postbuckling solutions of the delaminated cylindrical shells, and with these solutions, the values of the energy release rates are determined. In simulational examples, the effects of a wide range of parameters, such as delamination sizes and depths, boundary conditions, geometrical parameters, material properties and laminate stacking sequences on the energy release rates of axisymmetrical laminated cylindrical shells are intensively discussed.

Fatigue Property of Nano-grained Delaminated Low-carbon Steel Sheet

Tension-tension fatigue life tests on nano-grained delaminated low-carbon steel sheet under different fatigue loads are carried out to study the fatigue properties of the steel. The three-dimensional microstructures of the steel are observed by TEM. In addition, the morphology of the fatigue fracture of the specimen under different loads is observed by SEM. The results show that micro-cracks form on the weak interface of the nano-grained steel under low-stress conditions, which hinders the propagation of the main cracks and reduces the fatigue crack propagation rate, resulting in the extending fatigue life of the steel.

High-temperature effect on continuous glass fiber reinforced polypropylene multilayer composite and corrugated sandwich panels

The high-temperature mechanical behaviors of Multi-Layer Composite Panels(MCP)and Corrugated Sandwich Panels(CSP)of Continuous Glass Fiber-Reinforced Polypropylene(CGFRPP)are critical for their application in aerospace fields,which have been rarely mentioned in previous studies.High-temperature quasi-static tensile and compression tests on CGFRPP MCP are conducted first.The results showed that the tensile and compression strength,stiffness,and tensile modulus of MCP decreased with increasing temperature.The Gibson model was found to be more suitable for predicting the high-temperature mechanical performance of MCP after comparing the calculated results of different theoretical models with experimental data.Secondly,hightemperature planar compression tests were conducted on the CGFRPP CSP,revealing that the main failure modes were corrugated core buckling and delamination between the face panel and core material,with delamination being intensified at higher temperatures.Therefore,we proposed a strength theoretical model that considers structural buckling failure and interface delamination failure,and introduced the influence factor to evaluate the effect of interface delamination on structural strength.

CONTACT ANALYSIS FOR FIBER-REINFORCED, DELAMINATED LAMINATES WITH KINEMATIC NONLINEARITY

A macro-micro analytical approach for the anti-penetrating contact problem at the interfaces of the delamination in symmetrically cross-plied,fiber-reinforced rectangular laminates is presented in this paper.The laminate is simply supported and subjected to a uniform transverse load with a through-width delamination buried at the center position.A contact factor is defined to characterize the contact effect and determined using the micro-mechanics of composite material.By analyzing the kinematics of nonlinear deformation at the interfaces of the delamination,the contact force is derived.Asymptotic solutions from perturbation analysis are presented.It is found that the deformation of the laminate involves a global deflection and a local buckling.The antipenetrating contact effects are characterized by the local buckling and are intrinsic properties of the laminates,relying only on the geometries of the delamination and the material properties.Parametric analyses show that the location and size of the contact areas and the distribution of the contact force are hardly affected by the aspect ratio.

ANALYSIS OF ELASTO-PLASTIC POSTBUCKLING AND ENERGY RELEASE RATE FOR DELAMINATED FIBER METAL LAMINATED BEAMS IN THERMAL ENVIRONMENT

The elasto-plastic postbuckling of fiber metal laminated beams with delamination and the energy release rate along the delamination front are discussed in this paper. Considering geometrical nonlinearity, thermal environment and geometrical initial imperfection, the incremental nonlinear equilibrium equations of delaminated fiber metal laminated beams are established, which are solved using the differential quadrature method and iterative method. Based on these, according to the J-integral theory, the elasto-plastic energy release rate is studied. The effects of some important parameters on the elasto-plastic postbuckling behavior and energy release rate of the aramid reinforced aluminum laminated beams are discussed in details.

Highly Porous Yet Transparent Mechanically Flexible Aerogels Realizing Solar-Thermal Regulatory Cooling

The demand for highly porous yet transparent aerogels with mechanical flexibility and solar-thermal dual-regulation for energy-saving windows is significant but challenging.Herein,a delaminated aerogel film(DAF)is fabricated through filtration-induced delaminated gelation and ambient drying.The delaminated gelation process involves the assembly of fluorinated cellulose nanofiber(FCNF)at the solid-liquid interface between the filter and the filtrate during filtration,resulting in the formation of lamellar FCNF hydrogels with strong intra-plane and weak interlayer hydrogen bonding.By exchanging the solvents from water to hexane,the hydrogen bonding in the FCNF hydrogel is further enhanced,enabling the formation of the DAF with intra-layer mesopores upon ambient drying.The resulting aerogel film is lightweight and ultra-flexible,which pos-sesses desirable properties of high visible-light transmittance(91.0%),low thermal conductivity(33 mW m^(-1) K^(-1)),and high atmospheric-window emissivity(90.1%).Furthermore,the DAF exhibits reduced surface energy and exceptional hydrophobicity due to the presence of fluorine-containing groups,enhancing its durability and UV resistance.Consequently,the DAF has demonstrated its potential as solar-thermal regulatory cooling window materials capable of simultaneously providing indoor lighting,thermal insulation,and daytime radiative cooling under direct sunlight.Significantly,the enclosed space protected by the DAF exhibits a temperature reduction of 2.6℃ compared to that shielded by conventional architectural glass.

Early Devonian Post-collisional Granitic Magmatism in the North Qilian Orogenic Belt,Western China:Insights into Lithospheric Delamination and Orogenic Collapse

Post-collisional magmatism contains important clues for understanding the reworking and growth of continental crust,as well as lithospheric delamination and orogenic collapse.Early Devonian magmatism has been identified in the North Qilian Orogenic Belt(NQOB).This paper reports an integrated study of petrology,whole-rock geochemistry,Sm-Nd isotope and zircon U-Pb dating,as well as Lu-Hf isotopic data,for two Early Devonian intrusive plutons.The Yongchang and Chijin granites yield zircon U-Pb ages of 394-407 Ma and 414 Ma,respectively.Both of them are characterized by weakly peraluminous to metaluminous without typical aluminium-rich minerals,LREE-enriched patterns with negative Eu anomalies and a negative correlation between P_(2)O_(5) and SiO_(2) contents,consistent with geochemical features of I-type granitoids.Zircons from the studied granites display negative to weak positive ε_(Hf)(t)values(−5.7 to 2.1),which agree well with those of negative ε_(Nd)(t)values(−6.4 to−2.9)for the whole-rock samples,indicating that they were derived from the partial melting of Mesoproterozoic crust.Furthermore,low Sr/Y ratios(1.13-21.28)and high zircon saturation temperatures(745℃ to 839℃,with the majority being>800℃)demonstrated a relatively shallow depth level below the garnet stability field and an additional heat source.Taken together,the Early Devonian granitic magmatism could have been produced by the partial melting of ancient crustal materials heated by mantle-derived magmas at high-temperature and low-pressure conditions during postcollisional extensional collapse.The data obtained in this study,when viewed in conjunction with previous studies,provides more information about the tectonic processes that followed the closure of the North Qilian Ocean.The tectonic transition from continental collision to post-collisional delamination could be constrained to~430 Ma,which is provided by the sudden decrease of Sr/Y and La/Yb ratios and an increase in zircon ε_(Hf)(t)values for granitoids.A two-stage tectonic evolution model from continental collision to post-collisional extensional collapse for the NQOB includes(a)continental collision and crustal thickening during ca.455-430 Ma,characterized by granulite-facies metamorphism and widespread low-Mg adakitic magmatism;(b)post-collisional delamination of thickened continental crust and extensional collapse of orogen during ca.430-390 Ma,provided by coeval high-Mg adakitic magmatism,A-type granites and I-type granitoids with low Sr-Y ratios.

Effect of Different Laser Energy Nitriding on the Fretting Wear Performance of Zr Alloy

The zirconium(Zr)alloy fuel cladding is one of the key structural components of a nuclear reactor and the first and most important line of defense for accommodating fission products.During the operation of nuclear reactors,Zr alloy fuel cladding is subjected to extreme harsh environments,such as high temperature,high pressure and high flow rate for a long period of time.The wear and corrosion resistance of Zr alloys is important for the safe operation of nuclear reactors.Surface modification can effectively improve the corrosion and wear resistance of fuel cladding.Compared with coating technology,nitriding technology does not have problems for bonding between the coating and the substrate.Current research on surface nitriding of Zr alloys mainly focuses on plasma nitriding and ion implantation techniques.Research on laser nitriding of Zr alloy surfaces and their fretting wear characteristics is scarce.In this study,the surface of Zr alloy was treated with laser nitriding at different laser energies.The microstructure of Zr alloy treated with different laser energies and its fretting wear performance were studied.The results showed that after nitriding with different laser energies,the surface of the Zr alloy showed a typical molten state after melting,vaporizing and cooling under the thermal effect of the laser,and this state was more obvious with the increase of the laser energy.At the same time,doping of N atoms and formation of the ZrN phase led to different cooling rates in the molten zone that produced large tensile stresses after cooling.This led to cracks on the surface of Zr alloys after laser nitriding at different energies,and the crack density increased with increasing laser energy.This also led to an increase in the surface roughness of the Zr alloy with increasing laser energy after laser nitriding treatment.Due to the presence of water in the industrial nitrogen,nitrides were generated on the surface of the sample along with some oxides.When the laser energy was 100 mJ,there was no ZrN generation,and N existed mainly as a diffusion layer within the Zr alloy substrate.ZrN generated when the laser energy reached 200 mJ and above,which increased with the increase of laser energy.Due to the generation of ZrN phase and the presence of some oxides,the surface Vickers hardness of Zr alloys after laser nitriding treatment at different energies increased by 37.5%compared to Zr alloys.After laser nitriding treatment,the wear mechanism of Zr alloys changed.For the untreated Zr alloys,the wear mechanism was dominated by delamination and spalling wear,accompanied by oxidative and abrasive wear.The phenomenon of delamination and peeling decreased with the increase of laser energy.Wear mechanisms changed to predominantly abrasive wear with oxidative wear and delamination spalling.The wear volume of sample nitriding with laser energy 400 mJ was reduced by 46.5%compared with that of untreated Zr alloy.

Enhanced air-coupled impact echo technique by phase analysis of signals from multiple sensors

This paper presents an air-coupled impact echo(IE)technique that relies on the phase spectrum of the collected data to find the frequencies corresponding to the reflections from delaminations.The proposed technique takes advantage of the fact that the IE compression wave is not a propagating wave,but it is the 1st order symmetrical(S1)mode Lamb wave at zero group velocity(S1-ZGV).Therefore,it searches the phase spectra of the data collected by multiple sensors to locate the frequency corresponding to the lowest phase difference.As a result,the technique reduces the effect of propagating waves,including the direct acoustic wave and ambient noise.It is named the Constant Phase IE(CPIE).The performance of the CPIE is experimentally compared with the regular amplitude spectrum-based IE technique and two other multisensor IE techniques.The CPIE shows a performance advantage,especially in a noisy environment.

Relocation of Uppermost Mantle Earthquakes in the Atlas Mountains, Morocco

Upper mantle earthquakes are usually associated with plate boundary tectonics, but rarely occur beneath intracontinental orogenic belts. In the Moroccan Atlas Mountains, earthquakes determined at subcrustal depths are a controversial topic because they are few in number compared to subduction zones and are not related to plate boundary tectonics. A recent increase of broadband stations in Morocco has revealed numerous events below the Atlas belts, thought to occur from the upper mantle. Using additional available stations, these Atlas events were relocated and new epicenter resolutions were acquired following rigorous depth and RMS error criteria. 309 events were reprocessed and epicenter depths obtained were between 31 and 240 km during the last 23 years. Temporal variations of High Atlas events appear to be continually dipping while Anti Atlas events show no temporal variation trends. In addition, a recent strong event M6.8 occurred in September 2023 at the transition crust-uppermost mantle followed by several aftershocks which have been relocated at uppermost mantle depths. These events support delamination model under the High-Middle Atlas which could flow southward beneath the Anti Atlas lithosphere, and explain the large variation observed in lithosphere thickness between the High-Middle Atlas, and the Anti Atlas. Subcrustal events beneath the Atlas may be related to upper mantle earthquakes beneath the neighboring Canary Islands which have experienced recent swarms and eruptions. This possible correlation cannot be excluded since descending and ascending material is necessary for a regional geodynamic balance.

A Two-step Inverse Method for Quantitative Damage Evaluation of Plate-like Structures Using Vibration Approach

This study presents a novel two-step approach to assess plate-like structural laminar damages,particularly for delamination damage detection of composite structures.Firstly,a 2-D continuous wavelet transform is employed to identify the damage location and sizes from vibration curvature data.An inverse method is subsequently then used to determine the bending stiffness reduction ratio along a specified direction,enabling the quantification of the delamination severity.The method employed in this study is an extension of the one-dimensional inverse method developed in a previous work of the authors.The applicability of the two-step inverse approach is demonstrated in a simulation analysis and by an experimental study on a cantilever composite plate containing a single delamination.The inverse method is shown to have the capacity to reveal the detailed damage information of delamination within a constrained searching space and can be used to determine the effective flexural stiffness of composite plate structures,even in cases of complex delamination damage.

Fretting wear behavior of Inconel 690 in hydrazine environments

The friction and wear behaviors of Inconel 690 flat against Si3Ni4 ball were investigated using a hydraulic fretting test rig equipped with a liquid container device. The loads of 20-80 N, reciprocating amplitudes of 80-200 μm and two different environments （distilled water and hydrazine solution at temperatures from 25 to 90 ℃） were selected. The results show that the ratio of Ft/Fn is lower in distilled water than that in hydrazine solution at the same temperature in the slip regime. Both the ratio of Ft/Fn and wear volume gradually increase with increasing medium temperature under the given normal load and displacement amplitude. Besides the displacement amplitude and load, temperature also plays an important role for wear behavior of Inconel 690 material. The increase of temperature could reduce the concentration of dissolved oxygen, and promote the absorption reaction of hydrazine and dissolved oxygen. As a result, the oxidative corrosion rate is obviously lowered. Abrasive wear and delamination wear are the main mechanisms of Inconel 690 in distilled water. However, in hydrazine solution the cracks accompanied by abrasive wear and delamination wear are the main mechanisms.

Buckling behavior of micro metal wire on polymer membrane under combined effect of electrical loading and mechanical loading

The buckling behavior of a typical structure consisting of a micro constantan wire and a polymer membrane under coupled electrical-mechanical loading was studied. The phenomenon that the constantan wire delaminates from the polymer membrane was observed after unloading. The interfacial toughness of the constantan wire and the polymer membrane was estimated. Moreover, several new instability modes of the constantan wire could be further triggered based on the buckle-driven delamination. After electrical loading and tensile loading, the constantan wire was likely to fracture based on buckling. After electrical loading and compressive loading, the constantan wire was easily folded at the top of the buckling region. On the occasion, the constantan wire buckled towards the inside of the polymer membrane under electrical-compressive loading. The mechanisms of these instability modes were analyzed.

Low-velocity Impact Damage Analysis of Composite Laminates Using Self-adapting Delamination Element Method

On the basis ofa 2D 4-node Mindlin shell element method, a novel self-adapting delamination finite element method is presented, which is developed to model the delamination damage of composite laminates. In the method, the sublaminate elements are generated automatically when the delamination damage occurs or extends. Thus, the complex process and state of delamination damage can be simulated practically with high efficiency for both analysis and modeling. Based on the self-adapting delamination method, linear dynamic finite element damage analysis is performed to simulate the low-velocity impact damage process of three types of mixed woven composite laminates. Taking the frictional force among sublaminations during delaminating and the transverse normal stress into account, the analytical results are consistent with those of the experimental data.

A Structural Interpretation Model and Restoration of the Mesozoic Proto-basin for the Kuqa Depression,Tarim Basin

A thrust-fold belt consisting of a series of thrusts and buckling folds developed in the Mesozoic and Cenozoic strata within the Kuqa Depression,Tarim Basin.In this study,a structural interpretation model of the Kuqa Depression is established and the Mesozoic proto-basin is reconstructed on the basis of outcrop geology along the basin margin,seismic,well-log and CEMP data.The model is called‘delaminate contractional deformation',which emphasizes the decoupling between the Cenozoic,Mesozoic,pre-Mesozoic and the basin-basement within the Kuqa Depression,but there is no unified detachment.The model has a shortening amount ranging from 12 km to 16 km and the depth involved in contractional deformation ranges from 21 km to 28 km.A prototype of the Mesozoic basin reconstructed by interpretation model is a subbasin superposed on the transitional zone between the uplift at the northern edge of the Tarim Craton and the southern Tianshan orogenic wedge formed in the Hercynian orogeny.Lithospheric thermal and crustal isostatic activity after the Hercynian orogeny maybe the controlling dynamic factors of basin subsidence during the Mesozoic and early Cenozoic,the difference in rock mechanical properties between different levels,craton and orogenic wedge being the major cause of the‘delaminate contractional deformation'during the Himalayan orogeny.

INTERLAMINAR FRACTURE TOUGHNESS OF MULTI-DIRECTIONAL LAMINATES

Based on the conventional compliance and area methods, a high precision method named the angle method is presented in this work. The interlaminar fracture toughness is determined by measurement of the load and the bending angle at the loading point without measurement of the crack length, and the improvement of the conventional compliance method is made, which is more precise and can be used to general DCB specimen with unequal flexural stiffness of the cantilevers. The interlaminar fracture toughness in 0/ θ(θ =0°,30°,60°,90°) interfaces of two epoxy composites, one being the carbon fibre reinforced brittle matrix T300/4211, the other the carbon fibre reinforced tough matrix T300/3261, is measured by both compliance and angle methods, and the relationship between fracture toughness and the ply angle θ is obtained. It is found that the interlaminar fracture toughness is correlated with the type of matrix and the ply angles near the crack front.

40Ar-39Ar Dating of Albite and Phlogopite from Porphyry Iron Deposits in the Ningwu Basin in East-Central China and Its Significance

40Ar-39Ar dating of albite from the Meishan and Taocun iron deposits yields plateau ages of 122.90±0.16 Ma and 124.89±0.30 Ma, and isochron ages of 122.60±0.16 Ma and 124.90±0.29 Ma, respectively. Phlogopite from the Zhongshan-Gushan ore field has a plateau age of 126.7±0.17 Ma and an isochron age of 127.21±1.63 Ma. Analysis of regional geodynamic evolution of the middle-lower Yangtze River region suggests that the porphyry iron deposits were formed as a result of large-scale lithosphere delamination and strong sinistral strike-slip movement of the Tancheng Lujiang fault zone. The copper, molybdenum and gold deposit system in the middle-lower Yangtze River region was formed during the stress transition period of the eastern China continent.

Computer Simulation of Thin Film Wrinkling on Elastic Substrate

Numerous theoretical and experimental efforts have been made to explain the dependence of the static wrink^h~g morphology on the materials＇ physical properties, whereas the dy- namic wrinkling process remains elusive. In the present work, we design a wrinkling model consisting of a soft substrate and a graphene-like rigid thin film to investigate this dynamic process. The simulation shows that the whole wrinkling process includes three stages. At the incubation and wrinkling stages, the stress along the horizon direction of the soft substrate transfers to the stiff film. However, at the equilibrium stage, the stress of the rigid film slowly transfers back to the substrate although the total energy still decreases. It is found that the stress of the substrate concentrates at the top surface, especially at the trough, whereas the stress distribution of the film depends on direction. In the perpendicular direc- tion, the stress at the wave＇s equilibrium position surpasses that at the crest and trough and, oppositely, the stress concentrates at the crest and trough in the horizon direction. Present model reproduces both wrinkling and delamination patterns and can be a powerful tool to deeply understand the structure deformation of material induced by stress release.