The penetration depth of atomic radicals in tubes with catalytic surface properties

Catalysis of molecular radicals is often performed in interesting experimental configurations.One possible configuration is tubular geometry.The radicals are introduced into the tubes on one side,and stable molecules are exhausted on the other side.The penetration depth of radicals depends on numerous parameters,so it is not always feasible to calculate it.This article presents systematic measurements of the penetration depth of oxygen atoms along tubes made from nickel,cobalt,and copper.The source of O atoms was a surfatron-type microwave plasma.The initial density of O atoms depended on the gas flow and was 0.7×10^(21)m^(-3),2.4×10^(21)m^(-3),and 4.2×10^(21)m^(-3)at the flow rates of 50,300,and 600 sccm,and pressures of 10,35,and 60 Pa,respectively.The gas temperature remained at room temperature throughout the experiments.The dissociation fraction decreased exponentially along the length of the tubes in all cases.The penetration depths for well-oxidized nickel were 1.2,1.7,and 2.4 cm,respectively.For cobalt,they were slightly lower at 1.0,1.3,and 1.6 cm,respectively,while for copper,they were 1.1,1.3,and 1.7 cm,respectively.The results were explained by gas dynamics and heterogeneous surface association.These data are useful in any attempt to estimate the loss of molecular fragments along tubes,which serve as catalysts for the association of various radicals to stable molecules.

Quantitative prediction model for the depth limit of oil accumulation in the deep carbonate rocks:A case study of Lower Ordovician in Tazhong area of Tarim Basin

With continuous hydrocarbon exploration extending to deeper basins,the deepest industrial oil accumulation was discovered below 8,200 m,revealing a new exploration field.Hence,the extent to which oil exploration can be extended,and the prediction of the depth limit of oil accumulation(DLOA),are issues that have attracted significant attention in petroleum geology.Since it is difficult to characterize the evolution of the physical properties of the marine carbonate reservoir with burial depth,and the deepest drilling still cannot reach the DLOA.Hence,the DLOA cannot be predicted by directly establishing the relationship between the ratio of drilling to the dry layer and the depth.In this study,by establishing the relationships between the porosity and the depth and dry layer ratio of the carbonate reservoir,the relationships between the depth and dry layer ratio were obtained collectively.The depth corresponding to a dry layer ratio of 100%is the DLOA.Based on this,a quantitative prediction model for the DLOA was finally built.The results indicate that the porosity of the carbonate reservoir,Lower Ordovician in Tazhong area of Tarim Basin,tends to decrease with burial depth,and manifests as an overall low porosity reservoir in deep layer.The critical porosity of the DLOA was 1.8%,which is the critical geological condition corresponding to a 100%dry layer ratio encountered in the reservoir.The depth of the DLOA was 9,000 m.This study provides a new method for DLOA prediction that is beneficial for a deeper understanding of oil accumulation,and is of great importance for scientific guidance on deep oil drilling.

Extraction of Acoustic Normal Mode Depth Functions Using Range-Difference Method with Vertical Linear Array Data

Data-derived normal mode extraction is an effective method for extracting normal mode depth functions in the absence of marine environmental data.However,when the corresponding singular vectors become nonunique when two or more singular values obtained from the cross-spectral density matrix diagonalization are nearly equal,this results in unsatisfactory extraction outcomes for the normal mode depth functions.To address this issue,we introduced in this paper a range-difference singular value decomposition method for the extraction of normal mode depth functions.We performed the mode extraction by conducting singular value decomposition on the individual frequency components of the signal's cross-spectral density matrix.This was achieved by using pressure and its range-difference matrices constructed from vertical line array data.The proposed method was validated using simulated data.In addition,modes were successfully extracted from ambient noise.

HVSR analysis of pumice sands for sediment depth characterization:A case study for Guadalajara,Mexico

The horizontal to vertical spectral ratio(HVSR)methodology is used here to characterize pumice soils and to image the three-dimensional surface geometry of Guadalajara,Mexico.Similar to other Latin American cities,Guadalajara is exposed to high seismic risk,with the particularity of being the largest urban settlement in Latin America built on pumice soils.Methodology has not yet been tested to characterize subsoil depths in pumice sands.Due to the questionable use of traditional geotechnical tests for the analysis of pumice soils,HVSR provides an alternative for its characterization without altering its fragile and porous structure.In this work,resonance frequency(F0)and peak amplitude(A0)are used to constrain the depth of the major impedance contrast that represents the interface between bedrock and pumice soil.Results were compared with borehole depths and other available geotechnical and geophysical data and show good agreement.One of the profiles estimated on the riverbanks that cross the city,reveals different subsoil thickness that could have an impact on different site responses on riverine areas to an eventual earthquake.Government and academic efforts are combined in this work to characterize depth sediments,an important parameter that impacts the regulations for construction in the city.

Spatiotemporal Changes of Snow Depth in Western Jilin,China from 1987 to 2018

Seasonal snow cover is a key global climate and hydrological system component drawing considerable attention due to glob-al warming conditions.However,the spatiotemporal snow cover patterns are challenging in western Jilin,China due to natural condi-tions and sparse observation.Hence,this study investigated the spatiotemporal patterns of snow cover using fine-resolution passive mi-crowave(PMW)snow depth(SD)data from 1987 to 2018,and revealed the potential influence of climate factors on SD variations.The results indicated that the interannual range of SD was between 2.90 cm and 9.60 cm during the snowy winter seasons and the annual mean SD showed a slightly increasing trend(P>0.05)at a rate of 0.009 cm/yr.In snowmelt periods,the snow cover contributed to an increase in volumetric soil water,and the change in SD was significantly affected by air temperature.The correlation between SD and air temperature was negative,while the correlation between SD and precipitation was positive during December and March.In March,the correlation coefficient exceeded 0.5 in Zhenlai,Da’an,Qianan,and Qianguo counties.However,the SD and precipitation were neg-atively correlated over western Jilin in October,and several subregions presented a negative correlation between SD and precipitation in November and April.

What induced the trend shift of mixed-layer depths in the Antarctic Circumpolar Current region in the mid-1980s?

An obvious trend shift in the annual mean and winter mixed layer depth(MLD)in the Antarctic Circumpolar Current(ACC)region was detected during the 1960–2021 period.Shallowing trends stopped in mid-1980s,followed by a period of weak trends.The MLD deepening trend difference between the two periods were mainly distributed in the western areas in the Drake Passage,the areas north to Victoria Land and Wilkes Land,and the central parts of the South Indian sector.The newly formed ocean current shear due to the meridional shift of the ACC flow axis between the two periods is the dominant driver for the MLD trends shift distributed in the western areas in the Drake Passage and the central parts of the South Indian sector.The saltier trends in the regions north to Victoria Land and Wilkes Land could be responsible for the strengthening mixing processes in this region.

Three-dimensional constrained gravity inversion of Moho depth and crustal structural characteristics at Mozambique continental margin

Mozambique's continental margin in East Africa was formed during the break-off stage of the east and west Gondwana lands. Studying the geological structure and division of continent-ocean boundary(COB) in Mozambique's continental margin is considered of great significance to rebuild Gondwana land and understand its movement mode. Along these lines, in this work, the initial Moho was fit using the known Moho depth from reflection seismic profiles, and a 3D multi-point constrained gravity inversion was carried out. Thus, highaccuracy Moho depth and crustal thickness in the study area were acquired. According to the crustal structure distribution based on the inversion results, the continental crust at the narrowest position of the Mozambique Channel was detected. According to the analysis of the crustal thickness, the Mozambique ridge is generally oceanic crust and the COB of the whole Mozambique continental margin is divided.

Investigation of Groundwater Quality with Borehole Depth in the Basin Granitoids of the Ashanti Region of Ghana

The dependence of groundwater quality on borehole depth is usually debatable in groundwater studies, especially in complex geological formations where aquifer characteristics vary spatially with depth. This study therefore seeks to investigate the relationship between borehole depth and groundwater quality across the granitoid aquifers within the Birimian Supergroup in the Ashanti Region. Physicochemical analysis records of groundwater quality data were collected from 23 boreholes of public and private institutions in the Ashanti Region of Ghana, and the parametric values of iron, fluoride, total hardness, pH, nitrate, and nitrite were used to study the groundwater quality-depth relationship. The results showed that the depth-to-groundwater quality indicated a marginal increase in water quality in the range of 30 to 50 m, which is mathematically represented by the low-value correlation coefficient (r2 = 0.026). A relatively significant increase occurs in the depth range of 50 to 80 m, which is given by a correlation coefficient of r2 = 0.298. The mean percent parameter compatibility was 74%, 82%, 89%, and 97% at 50, 60, 70, and 80 m depths, respectively. The variations in groundwater quality per depth ratio ranged from 1.48, 1.37, 1.27, and 1.21 for 50, 60, 70, and 80 m depth, respectively. The recommended minimum borehole depth for excellent groundwater quality is suggested with a compatibility per meter depth ratio of 1.37. This results in a range between 50 and 70 m as the most desirable drilling depth for excellent groundwater quality within the granitoids of the Birimian Supergroup of the Ashanti Region in Ghana.

Spatio-temporal variation of depth to groundwater level and its driving factors in arid and semi-arid regions of India

Climate change and increasing anthropogenic activities,such as over-exploitation of groundwater,are exerting unavoidable stress on groundwater resources.This study investigated the spatio-temporal variation of depth to groundwater level(DGWL)and the impacts of climatic(precipitation,maximum temperature,and minimum temperature)and anthropogenic(gross district product(GDP),population,and net irrigated area(NIA))variables on DGWL during 1994-2020.The study considered DGWL in 113 observation wells and piezometers located in arid western plains(Barmer and Jodhpur districts)and semi-arid eastern plains(Jaipur,Ajmer,Dausa,and Tonk districts)of Rajasthan State,India.Statistical methods were employed to examine the annual and seasonal patterns of DGWL,and the generalized additive model(GAM)was used to determine the impacts of climatic and anthropogenic variables on DGWL.During 1994-2020,except for Barmer District,where the mean annual DGWL was almost constant(around 26.50 m),all other districts exhibited increase in DGWL,with Ajmer District experiencing the most increase.The results also revealed that 36 observation wells and piezometers showed a statistically significant annual increasing trend in DGWL and 34 observation wells and piezometers exhibited a statistically significant decreasing trend in DGWL.Similarly,32 observation wells and piezometers showed an statistically significant increasing trend and 37 observation wells and piezometers showed a statistically significant decreasing trend in winter;33 observation wells and piezometers indicated a statistically significant increasing trend and 34 had a statistically significant decreasing trend in post-monsoon;35 observation wells and piezometers exhibited a statistically significant increasing trend and 32 observation wells and piezometers showed a statistically significant decreasing trend in pre-monsoon;and 36 observation wells and piezometers reflected a statistically significant increasing trend and 30 observation wells and piezometers reflected a statistically significant decreasing trend in monsoon.Interestingly,most of the observation wells and piezometers with increasing trends of DGWL were located in Dausa and Jaipur districts.Furthermore,the GAM analysis revealed that climatic variables,such as precipitation,significantly affected DGWL in Barmer District,and DGWL in all other districts was influenced by anthropogenic variables,including GDP,NIA,and population.As a result,stringent regulations should be implemented to curb excessive groundwater extraction,manage agricultural water demand,initiate proactive aquifer recharge programs,and strengthen sustainable management in these water-scarce regions.

Determination of minimum overburden depth for underwater shield tunnel in sands:Comparison between circular and rectangular tunnels

With the development of global urbanization,the utilization of underground space is more critical and attractive for civil purposes.Various shapes of shield tunnels have been gradually proposed to cope with different geological conditions and service purposes of underground structures.Generally,reducing the burial depth of shield tunnel is conducive to construction and cost saving.However,extremely small overburden depth cannot provide sufficient uplift resistance to maintain the stability and serviceability of the tunnel.To this end,this paper firstly reviewed the status of deriving the minimum sand over-burden depth of circular shield tunnel using mechanical equilibrium(ME)method.It revealed that the estimated depth is rather conservative.Then,the uplift resistance mechanism of both circular and rectangular tunnels was deduced theoretically and verified with the model tests.The theoretical uplift resistance is consistent with the experimental values,indicating the feasibility of the proposed equations.Furthermore,the determination of the minimum soil overburden depth of rectangular shield tunnel under various working conditions was presented through integrated ME method,which can provide more reasonable estimations of suggested tunnel burial depth for practical construction.Additionally,optimizations were made for calculating the uplift resistance,and the soil thickness providing uplift resistance is suggested to be adjusted according to the testing results.The results can provide reference for the design and construction of various shapes of shield tunnels in urban underground space exploitation.

Speckle structured illumination endoscopy with enhanced resolution at wide field of view and depth of field

Structured illumination microscopy(SIM)is one of the most widely applied wide field super resolution imaging techniques with high temporal resolution and low phototoxicity.The spatial resolution of SIM is typically limited to two times of the diffraction limit and the depth of field is small.In this work,we propose and experimentally demonstrate a low cost,easy to implement,novel technique called speckle structured illumination endoscopy(SSIE)to enhance the resolution of a wide field endoscope with large depth of field.Here,speckle patterns are used to excite objects on the sample which is then followed by a blind-SIM algorithm for super resolution image reconstruction.Our approach is insensitive to the 3D morphology of the specimen,or the deformation of illuminations used.It greatly simplifies the experimental setup as there are no calibration protocols and no stringent control of illumination patterns nor focusing optics.We demonstrate that the SSIE can enhance the resolution 2–4.5 times that of a standard white light endoscopic(WLE)system.The SSIE presents a unique route to super resolution in endoscopic imaging at wide field of view and depth of field,which might be beneficial to the practice of clinical endoscopy.

Influence of the upper mixed layer depth on Langmuir turbulence characteristics

The upper mixed layer depth(h)has a significant seasonal variation in the real ocean and the low-order statistics of Langmuir turbulence are dramatically influenced by the upper mixed layer depth.To explore the influence of the upper mixed layer depth on Langmuir turbulence under the condition of the wind and wave equilibrium,the changes of Langmuir turbulence characteristics with the idealized variation of the upper mixed layer depth from very shallow(h=5 m)to deep enough(h=40 m)are studied using a non-hydrostatic large eddy simulation model.The simulation results show that there is a direct entrainment depth induced by Langmuir turbulence(h_(LT))within the thermocline.The normalized depthaveraged vertical velocity variance is smaller and larger than the downwind velocity variance for the ratio of the upper mixed layer to a direct entrainment depth induced by Langmuir turbulence h/h_(LT)<1 and h/h_(LT)>1,respectively,indicating that turbulence characteristics have the essential change(i.e.,depth-averaged vertical velocity variance(DAVV)DADV for Langmuir turbulence)between h/h_(LT)<1 and h/h_(LT)>1.The rate of change of the normalized depth-averaged low-order statistics for h/h_(LT)<1 is much larger than that for h/h_(LT)>1.The reason is that the downward pressure perturbation induced by Langmuir cells is strongly inhibited by the upward reactive force of the strong stratified thermocline for h/h_(LT)<1 and the eff ect of upward reactive force on the downward pressure perturbation becomes weak for h/h_(LT)>1.Hence,the upper mixed layer depth has significant influences on Langmuir turbulence characteristics.

Fusion of color and hallucinated depth features for enhanced multimodal deep learning-based damage segmentation

Recent advances in computer vision and deep learning have shown that the fusion of depth information can significantly enhance the performance of RGB-based damage detection and segmentation models.However,alongside the advantages,depth-sensing also presents many practical challenges.For instance,the depth sensors impose an additional payload burden on the robotic inspection platforms limiting the operation time and increasing the inspection cost.Additionally,some lidar-based depth sensors have poor outdoor performance due to sunlight contamination during the daytime.In this context,this study investigates the feasibility of abolishing depth-sensing at test time without compromising the segmentation performance.An autonomous damage segmentation framework is developed,based on recent advancements in vision-based multi-modal sensing such as modality hallucination(MH)and monocular depth estimation(MDE),which require depth data only during the model training.At the time of deployment,depth data becomes expendable as it can be simulated from the corresponding RGB frames.This makes it possible to reap the benefits of depth fusion without any depth perception per se.This study explored two different depth encoding techniques and three different fusion strategies in addition to a baseline RGB-based model.The proposed approach is validated on computer-generated RGB-D data of reinforced concrete buildings subjected to seismic damage.It was observed that the surrogate techniques can increase the segmentation IoU by up to 20.1%with a negligible increase in the computation cost.Overall,this study is believed to make a positive contribution to enhancing the resilience of critical civil infrastructure.

Secondary electron emission and photoemission from a negative electron affinity semiconductor with large mean escape depth of excited electrons

The formulae for parameters of a negative electron affinity semiconductor(NEAS)with large mean escape depth of secondary electrons A(NEASLD)are deduced.The methods for obtaining parameters such asλ,B,E_(pom)and the maximumδandδat 100.0 keV≥E_(po)≥1.0 keV of a NEASLD with the deduced formulae are presented(B is the probability that an internal secondary electron escapes into the vacuum upon reaching the emission surface of the emitter,δis the secondary electron yield,E_(po)is the incident energy of primary electrons and E_(pom)is the E_(po)corresponding to the maximumδ).The parameters obtained here are analyzed,and it can be concluded that several parameters of NEASLDs obtained by the methods presented here agree with those obtained by other authors.The relation between the secondary electron emission and photoemission from a NEAS with large mean escape depth of excited electrons is investigated,and it is concluded that the presented method of obtaining A is more accurate than that of obtaining the corresponding parameter for a NEAS with largeλ_(ph)(λ_(ph)being the mean escape depth of photoelectrons),and that the presented method of calculating B at E_(po)>10.0 keV is more widely applicable for obtaining the corresponding parameters for a NEAS with largeλ_(ph).

Depth profiling of arsenian pyrite in Carlin-type ores through wet chemistry

Enrichment of As and Au at the overgrowth rims of arsenian pyrite is a distinctive feature of Carlin-type gold ores.Revealing distribution of such key elements in high resolution is of fundamental importance yet often proves challenging.In this study,repeated non-oxidative acid etching of ore samples from Shuiyindong gold deposit was applied to enable elemental depth profiling of goldbearing arsenian pyrite grains.ICP-OES and AAS were used to determine the dissolved Fe,As,and Au concentrations in each of the etching solutions,and XPS was carried out to exam the etched mineral surfaces.In contrast to conventional ion beam etching that may cause substantial sample damage,our acid etching method does not seem to significantly alter the composition and chemical state of the samples.The etched depths directly converted from the measured elemental concentrations can reproducibly reach a very high resolution of~1 nm,and can be conveniently controlled through varying the etching time.While the Fe and As depth profiles consistently reflect the surface oxidation property of arsenian pyrite,the Au profile displaying an obvious upward trend reveals the ore fluid evolution at the late stage of mineralization.Based on our experimental results,we demonstrate that our wet chemistry method is capable of effective depth profiling of gold ore and perhaps other geological samples,with advantages surpassing many instrumental techniques including negligible sample damage,nanoscale resolution as well as isotropic etching.

Considering explosive charge shape and embedded depth in the design of concrete shelter thickness

Cost and safety are important considerations when designing the thickness of a protective reinforced concrete shelter.The blast perforation limit(BPL)is the minimum concrete shelter thickness that resists perforation under blast loading.To investigate the influence of the depth of embedment(DOE)and length-to-diameter ratio(L/D)of an explosive charge on the BPL,the results of an explosion test using a slender explosive partially embedded in a reinforced concrete slab were used to validate a refined finite element model.This model was then applied to conduct more than 300 simulations with strictly controlled variables,obtaining the BPLs for various concrete slabs subjected to charge DOEs ranging from0 to∞and L/D values ranging from 0.89 to 6.87.The numerical results were compared with the experimental results from published literature,further verifying the reliability of the simulation.The findings indicate that for the same explosive charge mass and L/D,the greater the DOE,the larger the critical residual thickness(Rc,defined as the difference between the BPL and DOE)up to a certain constant value;for the same explosive charge mass and DOE,the greater the L/D,the smaller the Rc.Thus,corresponding DOE and shape coefficients were introduced to derive a new equation for the BPL,providing a theoretical approach to the design and safety assessment of protective structures.

Wave Force on the Crown Wall of Rubble Mound Breakwaters at Intermediate Depths

Rubble mound breakwaters with a crown wall are a common coastal engineering structure.The wave force on crown walls is an important parameter for the practice engineering design.Particularly,the wave force on crown walls under intermediate depths has been studied through physical model tests and numerical simulations.In this study,a three-dimensional numerical wave flume was developed to investigate monochromatic wave interactions in a rubble mound breakwater with a crown wall.Armor blocks were modeled in detail.The Navier-Stokes equations for two-phase incompressible flows,combined with shear stress transport k-ωturbulence model and volume of fluid method for tracking the free surface,were solved.A set of laboratory experiments were performed to validate the adopted model.Subsequently,a series of numerical simulations were implemented to examine the impacts of different hydrodynamic parameters(including wave height,incident wave period,and water depth)and the berm width on the wave force of the crown wall.Finally,a comparison of the experimental results and Martin method shows that the latter method is not suitable for this experimental scope.New empirical formulas are proposed to predict the wave force on crown walls under intermediate depth.The results can provide a basis for the design of crown wall of rubble mound breakwaters at intermediate depths.

Retrieval of snow depth on Antarctic sea ice from the FY-3D MWRI data

The snow depth on sea ice is an extremely critical part of the cryosphere.Monitoring and understanding changes of snow depth on Antarctic sea ice is beneficial for research on sea ice and global climate change.The Microwave Radiation Imager(MWRI)sensor aboard the Chinese FengYun-3D(FY-3D)satellite has great potential for obtaining information of the spatial and temporal distribution of snow depth on the sea ice.By comparing in-situ snow depth measurements during the 35th Chinese Antarctic Research Expedition(CHINARE-35),we took advantage of the combination of multiple gradient ratio(GR(36V,10V)and GR(36V,18V))derived from the measured brightness temperature of FY-3D MWRI to estimate the snow depth.This method could simultaneously introduce the advantages of high and low GR in the snow depth retrieval model and perform well in both deep and shallow snow layers.Based on this,we constructed a novel model to retrieve the FY-3D MWRI snow depth on Antarctic sea ice.The new model validated by the ship-based observational snow depth data from CHINARE-35 and the snow depth measured by snow buoys from the Alfred Wegener Institute(AWI)suggest that the model proposed in this study performs better than traditional models,with root mean square deviations(RMSDs)of 8.59 cm and 7.71 cm,respectively.A comparison with the snow depth measured from Operation IceBridge(OIB)project indicates that FY-3D MWRI snow depth was more accurate than the released snow depth product from the U.S.National Snow and Ice Data Center(NSIDC)and the National Tibetan Plateau Data Center(NTPDC).The spatial distribution of the snow depth from FY-3D MWRI agrees basically with that from ICESat-2;this demonstrates its reliability for estimating Antarctic snow depth,and thus has great potential for understanding snow depth variations on Antarctic sea ice in the context of global climate change.

Morphotype dependence of Globigerinoides ruber(white)and Trilobatus sacculifer Mg/Ca ratios in the western tropical Pacific:implications for reconstructing the mixed-layer depth

Planktonic foraminifer Globigerinoides ruber(white)and Trilobatus sacculifer are the most frequently used mixedlayer dwelling species for reconstructing past oceanic environments.Specifically,the Mg/Ca ratios of these two foraminiferal species have been used for reconstructing tropical/subtropical changes in sea surface temperature(SST).However,these two species have different morphotypes,of which the spatial and temporal differences in Mg/Ca ratios and their influencing factors are still unclear.Our objective is to investigate the potential differences between the Mg/Ca ratios of these different morphotypes of G.ruber(white)and T.sacculifer in the western Philippine Sea(WPS)and determine their implications for the reconstruction of SST and upper-ocean structure.Mg/Ca measurements are made on two basic morphotypes of G.ruber(white)[sensu stricto(s.s.)and sensu lato(s.l.)]and T.sacculifer[with(w)and without(w/o)a sac-like final chamber]on samples of Site MD06-3047B from the WPS.Our results reveal that Mg/Ca ratios of different G.ruber morphotypes show consistent differences;and those of T.sacculifer morphotypes show staged variations since MIS 3.It is suggested to select a single morphotype for reconstructing SST changes using the Mg/Ca ratios of G.ruber and T.sacculifer in the WPS.Furthermore,the Mg/Ca ratios between G.ruber s.s.and G.ruber s.l.[Δ(Mg/Ca)_(G.ruber s.s.-s.l.)]downcore MD06-3047B covaries with indexes of summer monsoon.Combining with the core-top results,showing regional variation of differences in theΔ(Mg/Ca)_(G.ruber s.s.-s.l.)over the western tropical Pacific,we propose thatΔ(Mg/Ca)_(G.ruber s.s.-s.l.)may tend to reflect summer mixed layer depth.

Experimental investigation of the impact of water depth, inlet water temperature, and fins on the productivity of a Pyramid Solar Still

This experimental study aimed to investigate the impact of water depth, inlet water temperature,and fins on the productivity of a pyramid solar still in producing distilled water. The experiment was conducted in three parts, where the first part explored the variation in water depth from 1 cm to 5 cm, the second part evaluated the effect of increasing inlet water temperature from 30℃ to 50℃, and the third part added fins at the bottom of the still at a specific inlet water depth. Results showed that basin depth had a significant impact on the still's production, with a maximum variation of 40.6% observed when the water level was changed from 1 cm to 5 cm. The daily freshwater production from the pyramid solar still ranged from 3.41 kg/m~2 for a water depth of 1 cm to 2.02 kg/m~2 for a depth of 5 cm. Adding fins at the bottom of the pyramid solar still led to a 7.5% increase in productivity, while adjusting the inlet water temperature from 30℃ to 40℃ and 50℃ resulted in a 15.3% and 21.2% increase, respectively. These findings highlighted the essential factors that can influence the productivity of pyramid solar stills and can be valuable in designing and operating efficient water desalination and purification technologies.