The penetration depth of atomic radicals in tubes with catalytic surface properties

Catalysis of molecular radicals is often performed in interesting experimental configurations.One possible configuration is tubular geometry.The radicals are introduced into the tubes on one side,and stable molecules are exhausted on the other side.The penetration depth of radicals depends on numerous parameters,so it is not always feasible to calculate it.This article presents systematic measurements of the penetration depth of oxygen atoms along tubes made from nickel,cobalt,and copper.The source of O atoms was a surfatron-type microwave plasma.The initial density of O atoms depended on the gas flow and was 0.7×10^(21)m^(-3),2.4×10^(21)m^(-3),and 4.2×10^(21)m^(-3)at the flow rates of 50,300,and 600 sccm,and pressures of 10,35,and 60 Pa,respectively.The gas temperature remained at room temperature throughout the experiments.The dissociation fraction decreased exponentially along the length of the tubes in all cases.The penetration depths for well-oxidized nickel were 1.2,1.7,and 2.4 cm,respectively.For cobalt,they were slightly lower at 1.0,1.3,and 1.6 cm,respectively,while for copper,they were 1.1,1.3,and 1.7 cm,respectively.The results were explained by gas dynamics and heterogeneous surface association.These data are useful in any attempt to estimate the loss of molecular fragments along tubes,which serve as catalysts for the association of various radicals to stable molecules.

The Magnetic Penetration Depth Calculated with the Mechanism of “Close-Shell Inversion”

Meissner effect is one of the two fundamental properties of superconductors, it allows them to actively exclude external magnetic fields from their interior, leaving the field to decay quickly from the surface to the interior within a very thin layer whose thickness is characterized by the penetration depth . Based on the mechanism of “close-shell inversion” for superconductivity proposed earlier, we proceed in this paper to calculate the magnetic penetration depth. It is found that repelling the external magnetic field is just a spontaneous and dynamic response of conduction electrons in superconductors. Calculation results show that the net magnetic field decays exponentially, in consistent with the existing theories and experimental data. .

Penetration Depth of Torpedo Anchor in Two-Layered Cohesive Soil Bed by Free Fall

The penetration depth of torpedo anchor in two-layered soil bed was experimentally investigated. A total of 177 experimental data were obtained in laboratory by varying the undrained shear strength of the two-layered soil and the thickness of the top soil layer. The geometric parameters of the anchor and the soil properties(the liquid limit, plastic limit, specific gravity, undrained shear strength, density, and water content) were measured. Based on the energy analysis and present test data, an empirical formula to predict the penetration depth of torpedo anchor in two-layered soil bed was proposed. The proposed formula was extensively validated by laboratory and field data of previous researchers. The results were in good agreement with those obtained for two-layered and single-layered soil bed.Finally, a sensitivity analysis on the parameters in the formula was performed.

Penetration depth for yaw-inducing bursting layer impacted by projectile

In order to accurately estimate the anti-penetration capacity of yaw-inducing bursting layer with irregular barriers on surface impacted by projectile,the theoretical model of attack angle and angular velocity for projectile impacting on irregular barrier was achieved according to the macroscopic relation of contact force versus contact time,in which the main factors such as the relative geometrical characteristics of projectile and irregular barrier,material property and impact velocity of projectile influencing on yaw-inducing effectiveness were considered.On the basis of considering synthetically the influences of attack angle,impact velocity,impact angle of projectile and uncontrolled free surface of target,the theoretical formulation of penetration depth for bursting layer with irregular barriers on surface impacted by projectile was presented by expressing the stress of an optional point on the nose of projectile according to the relation of stress versus velocity.The theoretical results indicate that in the case of oblique impact embodying effect of attack angle,the penetration depth is reduced with the increase of impact angle,attack angle or angular velocity,and penetration trajectory is also deflected obviously.The effectiveness of angular velocity influencing on penetration depth is increased with impact velocity increasing.The theoretical results are in good agreement with test data for low impact velocity.

Photon penetration depth in human brain for light stimulation and treatment:A realistic Monte Carlo simulation study

Light has been clinically utilized as a stimulation in medical treatment,such as Low-level laser therapy and photodynamic thenapy,which has been more and more widely accepted in public.The penetration depth of the treatment light is important for precision treatment and safety control.The isue of light penetration has been highlighted in biomedical optics field for decades.However,quantitative research is sparse and even there are conflicts of view on the capability of near-infrared light penet ration into brain tissue.This study attempts to quantitatively revisit this issue by innovative high-realistic 3D Monte Caro modeling of stimulated light penetnation within high precision Visible Chinese human head.The properties of light,such as its wave-length,ilumination profle and size are concern in this study.We made stra ightforward and quantitative comparisons among the ffects by the light properties(i.e.,wavelengths:660,810 and 980 nn;beam types:Gaussi an and flat beamn;bear dianeters:0,2,4 and 6 cm)which are in the range of light treatment.The findings include about 3%of light dosage within brain tisue;the combination of Gaussian beam and 810nm light make the max imum light penetration(>5cm),which allows light to cross through gray matter into white mater.This study offered us,the first time as we know,quantitative guide for light stimulation parameter optimization in medical treatment.

A simple approach for the estimation of CO_2 penetration depth into a caprock layer

Caprock is a water-saturated formation with a sufficient entry capillary pressure to prevent the upward migration of a buoyant fluid. When the entry capillary pressure of caprock is smaller than the pressure exerted by the buoyant CO2plume, CO2gradually penetrates into the caprock. The CO2penetration depth into a caprock layer can be used to measure the caprock sealing efficiency and becomes the key issue to the assessment of caprock sealing efficiency. On the other hand, our numerical simulations on a caprock layer have revealed that a square root law for time and pore pressure exists for the CO2penetration into the caprock layer. Based on this finding, this study proposes a simple approach to estimate the CO2penetration depth into a caprock layer. This simple approach is initially developed to consider the speed of CO2invading front. It explicitly expresses the penetration depth with pressuring time, pressure difference and pressure magnitude. This simple approach is then used to fit three sets of experimental data and good fittings are observed regardless of pressures, strengths of porous media, and pore fluids(water,hydrochloric acid, and carbonic acid). Finally, theoretical analyses are conducted to explore those factors affecting CO2penetration depth. The effects of capillary pressure, gas sorption induced swelling, and fluid property are then included in this simple approach. These results show that this simple approach can predict the penetration depth into a caprock layer with sufficient accuracy, even if complicated interactions in penetration process are not explicitly expressed in this simple formula.

Simulations of the effects of density and temperature profile on SMBI penetration depth based on the HL-2A tokamak configuration

Using the trans-neut module of the BOUT＋＋ code, we study how the fueling penetration depth of supersonic molecular beam injection（SMBI） is affected by plasma density and temperature profiles. The plasma densities and temperatures in L-mode are initialized to be a set of linear profiles with different core plasma densities and temperatures. The plasma profiles are relaxed to a set of steady states with different core plasma densities or temperatures. For a fixed gradient, the steady profiles are characterized by the core plasma density and temperature. The SMBI is investigated based on the final steady profiles with different core plasma densities or temperatures. The simulated results suggest that the SMB injection will be blocked by dense core plasma and high-temperature plasma. Once the core plasma density is set to be N（i0）= 1.4N0（N0= 1 × 10^19m^-3） it produces a deeper penetration depth. When N（i0） is increased from 1.4N0 to 3.9N0 at intervals of 0.8N0, keeping a constant core temperature of T（e0）= 725 eV at the radial position of ψ = 0.65, the penetration depth gradually decreases. Meanwhile, when the density is fixed at N（i0）= 1.4N0 and the core plasma temperature T（e0） is set to 365 eV,the penetration depth increases. The penetration depth decreases as T（e0） is increased from 365 eV to 2759 eV. Sufficiently large N（i0） or T（e0） causes most of the injected molecules to stay in the scrape-off-layer（SOL） region, lowering the fueling efficiency.

Spatial distribution of penetration depth in Taihu Lake (China) during spring and autumn

In the context of remote sensing, sunlight penetration depth is the depth above which 90% of the diffusely reflected irradiance from a water body surface originates. Model algorithms to simulate water quality variables such as chlorophyll a, dissolved organic matter, suspended matter, and Secchi depth are sensitive to the variations of this variable. The penetration depth for Taihu Lake in China, a shallow and turbid lake, was calculated by using a multiple scattering model, and in situ optical measurements were carried out during May and October 2010. The results show that:1) the penetration depth generally increased from west to east during spring and from southeast to northwest during autumn, reflecting the prevailing wind direction and; 2) there was strong dependence of the penetration depth on the concentration of suspended matter.

Comparison Among Depths of Penetration of Different Targets Subjected to Rigid Projectile Impact

The ratios of depth of penetration (DOP) of different targets under the same penetration condition was investigated according to the dimensionless formula of DOP of different targets penetrated by a non-deformable projectile.Results show that various targets may be equivalent to each other.The applicable range of the equivalence and the feasibility of targets substitution were discussed by integrating the available test data.

Effect of process parameters on depth of penetration and topography of AZ91 magnesium alloy in abrasive water jet cutting

In the present study,the influence of dynamic process parameters such as water pressure,traverse speed and abrasive mass flow rate on depth of penetration and surface topography in high strength AZ91 magnesium alloy were investigated using Abrasive Water Jet(AWJ)cutting technology.Process parameters were varied at 3 levels and influences of each parameter on penetration ability were identified using analysis of variance(ANOVA).Contribution of water pressure and traverse speed on jet penetration found higher compared to abrasive mass flow rate.Profile projector was used to measure depth of penetration.Microstructural features and topography of cut surfaces were examined using Scanning Electron Microscopy(SEM).Micro cutting and ploughing were observed on the top and bottom portion of the cut which were similar to that of modes of deformation in other ductile materials like aluminium and steel.Surface roughness of cut surfaces was measured using Taylor Hobson surface roughness tester.Surface roughness found higher at higher traverse speeds and lower at lower traverse speeds.This study also highlights the suitability of AWJ cutting technology for cutting magnesium and its alloys.

RELATIONSHIP BETWEEN PLASMA OPTIC SIGNAL AND PENETRATION DEPTH FOR PARTIAL-PENETRATION LASER WELDING

Through sampling and analyzing of plasma optic signals of 400-600 nm emitted from partial-penetration laser welding processes, how the penetration depth is related to the welding parameter and the plasma optic signal is studied, Under the experimental conditions, the plasma optic signal has good response to variety of the weld penetration, and the signal＇s RMS value increases with the penetration in a quadratic curve mode. The inherent relation between the plasma optic signal and the penetration depth is also analyzed. It is also found that, between the two common parameters of laser power and welding speed, laser power has more influence on penetration while welding speed has more influence on weld width. The research results provide theoretic and practical bases for penetration real-time monitoring or predicting in partial-penetration laser welding,

A STUDY ON PENETRATION DEPTH OF POLARIZATION IMAGING

Optical clearing improves the penetration depth of optical measurements in turbid tissues.Polarization imaging has been demonstrated as a potentially promising tool for detecting cancers in superficial tissues,but its limited depth of detection is a major obstacle to the effective application in clinical diagnosis.In the present paper,detection depths of two polarization imaging methods,i.e.,rotating linear polarization imaging(RLPI)and degree of polarization imaging(DOPI),are examined quantitatively using both experiments and Monte Carlo simulations.The results show that the contrast curves of RLPI and DOPI are different.The characteristic depth of DOPI scales with transport mean free path length,and that of RLPI increases slightly with g.Both characteristic depths of RLPI and DOPI are on the order of transport mean free path length and the former is almost twice as large as the latter.It is expected that they should have different response to optical clearing process in tissues.

Round robin using the depth of penetration test method on an armour grade alumina

The depth of penetration(DOP)method is a well-known ballistic test method for characterisation and ranking of ceramic armour materials.The ceramic tile is bonded to a backing material of semi-infinite thickness,and the penetration depth of the projectile gives a measure of the performance of the ceramic.There is,however,an inherent variability in the results from this test method.In this work,the accuracy and the variability of the DOP method has been investigated in a round robin exercise.Six ballistic test centres took part in the exercise.A test protocol was developed,in which the threat type(projectile and impact conditions)and a procedure on how to prepare the targets were specified.The targets consisted of alumina tiles of two different thicknesses that were bonded to polycarbonate backing cubes.Two different 7.62 mm armour piercing projectiles were employed;one with a hard steel core and one with a tungsten carbide core.The projectiles and the other materials all came from single material batches in order to avoid batch-to-batch variations in material properties.These materials were distributed between the ballistic test centres.The test results of the different ballistic test facilities were collected and compared.There was not a lot of variation between the average DOP values obtained at each laboratory,but the variation in penetration depth between shots was high.The consequence of this variation may be less confidence in the test results,and a statistical method was used to evaluate the required number of tests that are sufficient to obtain an average result with high confidence.In most cases,the required number of tests is much higher than what is practically feasible.This work was conducted as part of the European Defence Agency-project CERAMBALL.

Fuzzy neural networks for control of penetration depthduring GTAW

An intelligent system including both a neural network(NN) and a self adjusting fuzzy controller(FC) for modeling and control of the penetration depth during gas tungsten arc welding(GTAW) process is presented in this paper. The discussion is mainly focused on two parts. One is the modeling of the penetration depth with NN. A visual sensor CCD is used to obtain the image of the molten pool. A neural network model is established to estimate the penetration depth from the welding current, pool width and seam gap. It is demonstrated that the proposed neural network can produce highly complex nonlinear multi variable model of the GTAW process that offer the accurate prediction of welding penetration depth. Another is the control for the penetration depth with FC.A self adjusting fuzzy controller is proposed,which used for controlling the penetration depth.The control parameters are adjusted on line automatically according to the controlling errors of penetration and the errors can be decreased sharply. The effectiveness of the proposed intelligent methods is demonstrated by the real experiments and the improved performance results are obtained.

Analysis of Penetration Depth of Pipeline on Cohesive Soil Seabed

This paper conducts laboratory tests to investigate detailedly the soil deformation law around the pipeline and its penetration depth under self-gravity. The seabed model is prepared by consolidating saturated soil using vacuum pressure technology, and the pipeline models are specifically designed to possess different radii. Based on the experimental results and digital images, the soil deformation process is analyzed and summarized, a kinematic admissible velocity field is given and an upper bound solution of pipeline penetration depth and soil reaction force is derived and proposed in this paper. In order to verify the accuracy of the upper bound solution deduced in this paper,a comparison is made among some published results and the solution suggested in this paper, the comparison results confirm that the upper bound solution and the soil failure mode are reasonable. Finally two empirical formulas are given in this paper to estimate the soil reaction force of seabed and the penetration depth of pipeline. The empirical formulas are in agreement with the upper bound solution derived in this paper, and the conclusion of this paper could provide some theoretical reference for the further study of the interaction between the pipeline and the soil.

The integrated intelligent system for welding seam error and penetration depth identification

A integrated intelligent system for seam tracking and penetration control is given. The system received information of welding seam error and penetration depth from only one sensor, then, it realized seam tracking and penetration control simultaneously. This paper introduces constitution of the system, methods of information recognition, design of the neural fuzzy controller and results practically.

Investigation of molecular penetration depth variation with SMBI fluxes

We study the molecular penetration depth variation with the SMBI fluxes.The molecular transport process and the penetration depth during SMBI with various injection velocities and densities are simulated and compared.It is found that the penetration depth of molecules strongly depends on the radial convective transport of SMBI and it increases with the increase of the injection velocity.The penetration depth does not vary much once the SMBI injection density is larger than a critical value due to the dramatic increase of the dissociation rate on the fueling path.An effective way to improve the SMBI penetration depth has been predicted,which is SMBI with a large radial injection velocity and a lower molecule injection density than the critical density.

Numerical investigation of sinusoidal pulsating gas intake to intensify the gas-slag momentum transfer in the top-blown smelting furnace

The variation characteristics of bubble morphology and the thermal-physical properties of bubble boundary in the top-blown smelting furnace were explored by means of the computational fluid dynamics method.The essential aspects of the fluid phase(e.g.,splashing volume,dead zone of copper slag,and gas penetration depth)were explored together with the effect of sinusoidal pulsating gas intake on the momentum-transfer performance between phases.The results illustrated that two relatively larger vortices and two smaller vortices appear in the bubble waist and below the lance,respectively.The expansion of larger ones as well as the shrinking of smaller ones combine to cause the contraction of the bubble waist.Compared to the results of the case with a fixed gas injection velocity(V_(g)=58 m/s),the splashing volume and dead zone volume of the slag under the V_(g)=58+10sin(2πt)condition are reduced by 24.9%and 23.5%,respectively,where t represents the instant time.Gas penetration depth and slag motion velocity of the latter are 1.03 and 1.31 times high-er than those of the former,respectively.

Influence of thickness and projectile shape on penetration resistance of the compliant composite

The present study deals with development of conceptual proof for jute rubber based flexible composite block to completely arrest the projectile impacting the target at high velocity impact of 400 m/s through numerical simulation approach using finite element(FE)method.The proposed flexible composite blocks of repeating jute/rubber/jute(JRJ)units are modelled with varying thickness from 30 mm to 120 mm in increments of 30 mm and impacted by flat(F),ogival(O)and hemispherical(HS)shaped projectiles.All the considered projectiles are impacted with proposed flexible composite blocks of different thicknesses and the penetration behaviour of the projectile in each case is studied.The penetration depth of the projectile in case of partially penetrated cases are considered and the effect of thickness and projectile shape on percentage of penetration depth is statistically analyzed using Taguchi’s design of experiments(DOE).Results reveal that the though proposed flexible composite block with thickness of 90 mm is just sufficient to arrest the complete penetration of the projectile,considering the safety issues,it is recommended to use the flexible composite with thickness of 120 mm.The nature of damage caused by the projectile in the flexible composite is also studied.Statistical studies show that thickness of the block plays a prominent role in determining the damage resistance of the flexible composite.

Experimental evaluation and modeling of liquid jet penetration to estimate droplet size in a three-phase riser reactor

In this work, the effects of injecting an evaporating liquid jet into solid-gas flow are experimentally investigated. A new model （SHED model） and a supplementary model （spray model） have also been proposed to investigate some flow-field characteristics in three-phase fluidized bed with the mean relative error 4.3% between model and measured results. Some experiments were conducted to study the influences of flow-field parameters such as liquid volumetric flow rate, injection velocity, jet angle and gas superficial velocity as well as solid mass flux on the jet penetration depth （JPD）. In addition, independent variables were experimentally employed to propose two empirical correlations for JPD by using multiple regression method and spray cone angle （SCA） by using dimensional analysis technique. The mean relative errors between the JPD and SCA correlations versus ex- perimental data were 7.5% and 3.9%, respectively. In addition, in order to identify the variable effect, a parametric study was carried out. Applying the proposed model can avoid direct use of expensive devices to measureJPD and to nredict dronlet size.