Design procedure for optimizing CMOS low noise operational amplifiers

This paper presents and experimentally verifies an optimized design procedure for a CMOS low noise operational amplifier. The design procedure focuses on the noise performance, which is the key requirement for low noise operational amplifiers. Based on the noise level and other specifications such as bandwidth, signal swing, slew rate, and power consumption, the device sizes and the biasing conditions are derived. In order to verify the proposed design procedure, a three-stage operational amplifier has been designed. The device parameters obtained from the proposed design procedure closely agree with the simulated results obtained by using HSPICE.

Design of controlled elastic and inelastic structures

One of the founders of structural control theory and its application in civil engineering, Professor Emeritus Tsu T. Soong, envisioned the development of the integral design of structures protected by active control devices. Most of his disciples and colleagues continuously attempted to develop procedures to achieve such integral control. In his recent papers published jointly with some of the authors of this paper, Professor Soong developed design procedures for the entire structure using a design - redesign procedure applied to elastic systems. Such a procedure was developed as an extension of other work by his disciples. This paper summarizes some recent techniques that use traditional active control algorithms to derive the most suitable （optimal, stable） control force, which could then be implemented with a combination of active, passive and semi-active devices through a simple match or more sophisticated optimal procedures. Alternative design can address the behavior of structures using Liapunov stability criteria. This paper shows a unified procedure which can be applied to both elastic and inelastic structures. Although the implementation does not always preserve the optimal criteria, it is shown that the solutions are effective and practical for design of supplemental damping, stiffness enhancement or softening, and strengthening or weakening.

Design and Analysis of a Novel Rotor-Segmented Axial-Field Switched Reluctance Machine

As excitation strategy is influenced by the parity of phase number,and serious end effect is caused by full pitch windings adopted by the conventional rotor-segmented switched reluctance machine(RS-SRM),a novel rotor-segmented axial-field switched reluctance machine(RS-AFSRM),which adopts concentrated windings,is proposed in this paper,whose control strategy is independent of the parity of phase number.The stator of the proposed RS-AFSRM consists of inner and outer flux-conductive ring,excitation poles,and stator yoke,while the rotor consists of fan-shape cylinder-type segments.The structure and principle of the proposed machine is introduced through the magnetic circuit model of the machine.The fringing effect on air-gap field is considered.The simplified magnetic circuit considering the fringing effect is presented and the fringing effect coefficient is introduced.The design procedure considering the fringing effect through iterative modification is presented in this paper and is validated through 3D finite-element method(3D-FEM).Results show that both magnetic field distribution and operation are reasonable and satisfy the requirements.

Design Strategy of Diagonal Compressors in Compressed Air Energy Storage System

As a kind of large-scale physical energy storage,compressed air energy storage(CAES)plays an important role in the construction of more efficient energy system based on renewable energy in the future.Compared with traditional industrial compressors,the compressor of CAES has higher off-design performance requirements.From the perspective of design,it needs to pay attention not only to the performance of the design point,but also to the performance of all the stable working range.However,from the previous literature,no diagonal compressor was used in CAES which can meet the requirements,which also reflects the design program can be further improved.Therefore,this paper studies the design strategy of high efficient diagonal compressor for large-scale CAES,and gives the complete strategy algorithms used for different program modules.The pressure ratio,isentropic efficiency and stable working range are comprehensively considered.In the design process,the criteria for the key parameters of the diagonal flow angle of the diagonal compressor are given for the first time.The results show that the isentropic efficiency at the design point is 92.7%,the total pressure ratio is1.97,and the stable working range exceeds 20%,which meets the design requirements of the compressor for CAES and exceeds the overall performance of the previous compressors in the entire working range.

Recent developments in seismically isolated buildings in Japan

The Building Standard Law of Japan and related Enforcement Order and Notifications have been substantially revised since the year 2000 to introduce a performance-based regulatory and deregulation system for building control systems. Up to then,time-history analyses were mandatory for isolated buildings and had to be specially approved by the Minster of the Ministry of Construction (MOC).Simplified design procedures based on the equivalent linear method for seismically isolated buildings have been issued as'Notification 2009-Structnral calculation procedure for buildings with seismic isolation'from MOC,and are now integrated into the Ministry of Land,Infrastructure,and Transportation (MLIT).Along with Notification 2009,'Notification 1446 of year 2000-Standard for specifications and test methods for seismic isolation devices'was also issued.Buildings with heights equal to or less than 60m and that are designed according to these Notifications,including base isolated buildings,only need approval from local building officials,and no longer require the special approval of the Minister of MLIT.This paper summarizes:1) some statistics related to buildings with seismic isolation completed up to the end of 2001; 2) simplified design procedures required by Notification 2009 of year 2000;and 3) performance of seismic isolation devices required by Notification 1446 of year 2000.

The Layout and Simulation of Logarithmic Spiral Double Curved Arch Dam Transverse Joints

Because of its good condition with mechanics, logarithmic spiral double curve arch bam has been widely used in the practical engineering. The introduction of a new method in how to divide transverse joint in arch dam will be given and the further research of its calculation has been done. The C＋＋ is used in electronic procedure and the 3D simulation has been finished with AutoCAD, which will provide the object model for computer simulation of the arch dam and the division of finite element mesh. Meanwhile, this method in dividing the transverse joint in arch dam also can be taken as the calculated basis for the design and calculation of arch dam, construction lofting and the calculation of the work amount.