Support design method for deep soft-rock tunnels in non-hydrostatic high in-situ stress field

Due to the long-term plate tectonic movements in southwestern China,the in-situ stress field in deep formations is complex.When passing through deep soft-rock mass under non-hydrostatic high in-situ stress field,tunnels will suffer serious asymmetric deformation.There is no available support design method for tunnels under such a situation in existing studies to clarify the support time and support stiffness.This study first analyzed the mechanical behavior of tunnels in non-hydrostatic in-situ stress field and derived the theoretical equations of the ground squeezing curve(GSC)and ground loosening curve(GLC).Then,based on the convergence confinement theory,the support design method of deep soft-rock tunnels under non-hydrostatic high in-situ stress field was established considering both squeezing and loosening pressures.In addition,this method can provide the clear support time and support stiffness of the second layer of initial support.The proposed design method was applied to the Wanhe tunnel of the China-Laos railway in China.Monitoring data indicated that the optimal support scheme had a good effect on controlling the tunnel deformation in non-hydrostatic high in-situ stress field.Field applications showed that the secondary lining could be constructed properly.

To improve robustness of mechanical properties of semi-solid cast A356 alloy using taguchi design method

Mechanical properties of semi-solid casting are dependent on multiple processing parameters,and improper processing parameters will not only reduce mean data but also increase variations.The present study investigated the impact of parameters in slurry preparation and heat treatment on the yield strength and ductility of T6 heat-treated A356 Al-Si alloy using rapid slurry forming(RSF)semi-solid casting.The focus was primarily on the robustness of mechanical properties based on Taguchi design method.By analyzing signal-to-noise ratio and minimum value calculated from-3S,the optimum slurry preparation parameters and heat treatment parameters were determined to be no quench,enthalpy exchange material(EEM)temperature of 140℃,EEM-to-melt ratio of 6mass%,stirring time of 18 s,solution heat treated at 520℃ for 2 h,and ageing heat treated at 190℃ for 6 h.In a small batch validation,the-3S yield strength and-3S elongation reach 256.1 MPa and 5.03% respectively,showing a satisfactory robustness.The hardness and microstructure of heat-treated samples with the best and worst properties were characterized to gain insight into the underlying mechanisms affecting the mean value and variations of mechanical properties.

Research on the design method for uniform wear of shield cutters in sand-pebble strata

During shield tunneling in highly abrasive formations such as sand–pebble strata,nonuniform wear of shield cutters is inevitable due to the different cutting distances.Frequent downtimes and cutter replacements have become major obstacles to long-distance shield driving in sand–pebble strata.Based on the cutter wear characteristics in sand–pebble strata in Beijing,a design methodology for the cutterhead and cutters was established in this study to achieve uniform wear of all cutters by the principle of frictional wear.The applicability of the design method was verified through three-dimensional simulations using the engineering discrete element method.The results show that uniform wear of all cutters on the cutterhead could be achieved by installing different numbers of cutters on each trajectory radius and designing a curved spoke with a certain arch height according to the shield diameter.Under the uniform wear scheme,the cutter wear coefficient is greatly reduced,and the largest shield driving distance is increased by approximately 47%over the engineering scheme.The research results indicate that the problem of nonuniform cutter wear in shield excavation could be overcome,thereby providing guiding significance for theoretical innovation and construction of long-distance shield excavation in highly abrasive strata.

A Mixed-Variable Experimental Design Method

Mixed-variable problems are inevitable in engineering. However, few researches pay attention to discrete variables. This paper proposed a mixed-variable experimental design method (ODCD): first, the design variables were divided into discrete variables and continuous variables;then, the DVD method was employed for handling discrete variables, the LHD method was applied for continuous variables, and finally, a Columnwise-Pairwise Algorithm was used for the overall optimization of the design matrix. Experimental results demonstrated that the ODCD method outperforms in terms of the sample space coverage performance.

Design methods for antimicrobial peptides with improved performance

The recalcitrance of pathogens to traditional antibiotics has made treating and eradicating bacterial infections more difficult.In this regard,developing new antimicrobial agents to combat antibiotic-resistant strains has become a top priority.Antimicrobial peptides(AMPs),a ubiquitous class of naturally occurring compounds with broadspectrum antipathogenic activity,hold significant promise as an effective solution to the current antimicrobial resistance(AMR)crisis.Several AMPs have been identified and evaluated for their therapeutic application,with many already in the drug development pipeline.Their distinct properties,such as high target specificity,potency,and ability to bypass microbial resistance mechanisms,make AMPs a promising alternative to traditional antibiotics.Nonetheless,several challenges,such as high toxicity,lability to proteolytic degradation,low stability,poor pharmacokinetics,and high production costs,continue to hamper their clinical applicability.Therefore,recent research has focused on optimizing the properties of AMPs to improve their performance.By understanding the physicochemical properties of AMPs that correspond to their activity,such as amphipathicity,hydrophobicity,structural conformation,amino acid distribution,and composition,researchers can design AMPs with desired and improved performance.In this review,we highlight some of the key strategies used to optimize the performance of AMPs,including rational design and de novo synthesis.We also discuss the growing role of predictive computational tools,utilizing artificial intelligence and machine learning,in the design and synthesis of highly efficacious lead drug candidates.

Current situation and development trend of design methods for subgrade structure of high speed railways

Purpose–This method will become a new development trend in subgrade structure design for high speed railways.Design/methodology/approach–This paper summarizes the structural types and design methods of subgrade bed for high speed railways in China,Japan,France,Germany,the United States and other countries based on the study and analysis of existing literature and combined with the research results and practices of high speed railway subgrade engineering at home and abroad.Findings–It is found that in foreign countries,the layered reinforced structure is generally adopted for the subgrade bed of high speed railways,and the unified double-layer or multi-layer structure is adopted for the surface layer of subgrade bed,while the simple structure is adopted in China;in foreign countries,different inspection parameters are adopted to evaluate the compaction state of fillers according to their respective understanding and practice,while in China,compaction coefficient,subsoil coefficient and dynamic deformation modulus are adopted for such evaluation;in foreign countries,the subgrade top deformation control method,the subgrade bottom deformation control method,the subsurface fill strength control method are mainly adopted in subgrade bed structure design of high speed railways,while in China,dynamic deformation control of subgrade surface and dynamic strain control of subgrade bed bottom layer is adopted in the design.However,the cumulative deformation of subgrade caused by train cyclic vibration load is not considered in the existing design methods.Originality/value–This paper introduces a new subgrade structure design method based on whole-process dynamics analysis that meets subgrade functional requirements and is established on the basis of the existing research at home and abroad on prediction methods for cumulative deformation of subgrade soil.

Mixed Method in Language Learner Cognition

Research on mixed method has made great development.In order to explore the practical application of mixed method,this article starts from the perspective of language learner cognition and selects The Modern Language Journal and Language Teaching Research as the research journals.It explores some empirical papers that used mixed method to learn the specific research designs of mixed method as well as the main means of its application.The study finds that mixed method has been applied in several fields and is more scientifically reliable than qualitative and quantitative methods especially in language learner cognition,and the different research tools used in the field of language learner cognition demonstrate the flexibility and relevance of mixed method data collection.

Landscape Design Methods of Urban Sponge Park

Urban rain-caused floods can not be well resolved with rising urban problem. Hence, construction of sponge park is born at the right moment. The research reviewed the concept, content and value of sponge parks and proposed theory and principle of landscape design in order to seek the method of landscape design of sponge parks, improve urban eco-environment and advance harmony development between human and nature.

Data Driven Vibration Control:A Review

With the ongoing advancements in sensor networks and data acquisition technologies across various systems like manufacturing,aviation,and healthcare,the data driven vibration control(DDVC)has attracted broad interests from both the industrial and academic communities.Input shaping(IS),as a simple and effective feedforward method,is greatly demanded in DDVC methods.It convolves the desired input command with impulse sequence without requiring parametric dynamics and the closed-loop system structure,thereby suppressing the residual vibration separately.Based on a thorough investigation into the state-of-the-art DDVC methods,this survey has made the following efforts:1)Introducing the IS theory and typical input shapers;2)Categorizing recent progress of DDVC methods;3)Summarizing commonly adopted metrics for DDVC;and 4)Discussing the engineering applications and future trends of DDVC.By doing so,this study provides a systematic and comprehensive overview of existing DDVC methods from designing to optimizing perspectives,aiming at promoting future research regarding this emerging and vital issue.

The Inheritance and Application of Chinese Reverse Contrast Typeface Style

This paper discusses the inheritance and application of Chinese character reverse contrast typeface style.It begins by analyzing the visual features of Western reverse contrast typeface styles,with a focus on Caslon Italian and French Clarendon,providing a Western perspective reference for subsequent Chinese character reverse contrast typeface style designs.The paper then traces the origins of the Chinese reverse contrast style,from the calligraphy style"Lacquer Script"to the earliest printing type"フワンテール形",exploring the historical background and cultural significance of the Chinese reverse contrast style.In the methodology section of Chinese character reverse contrast typeface style design,the discussion is conducted from two dimensions:inheritance and application.In terms of inheritance,through an in-depth analysis of"Lacquer Script"and"フワンテール形"typeface style,the paper summarizes three basic theories for modern Chinese character reverse contrast typeface style design.In the application section,it examines in detail the two most influential recent typeface styles,"Ribaasu"and"Basic Artistic",outlining three directions of application:extreme horizontal stroke variations,exaggerated contrast,and diverse decorative strokes,showcasing new directions and possibilities for Chinese character reverse contrast typeface style design.This paper not only reviews the developmental history of the Chinese character reverse contrast typeface style but also analyzes the design methodology of Chinese character reverse contrast typeface style through specific case studies.

Design,preparation,application of advanced array structured materials and their action mechanism analyses for high performance lithium-sulfur batteries

Lithium-sulfur battery(LSB)has brought much attention and concern because of high theoretical specific capacity and energy density as one of main competitors for next-generation energy storage systems.The widely commercial application and development of LSB is mainly hindered by serious“shuttle effect”of lithium polysulfides(Li PSs),slow reaction kinetics,notorious lithium dendrites,etc.In various structures of LSB materials,array structured materials,possessing the composition of ordered micro units with the same or similar characteristics of each unit,present excellent application potential for various secondary cells due to some merits such as immobilization of active substances,high specific surface area,appropriate pore sizes,easy modification of functional material surface,accommodated huge volume change,enough facilitated transportation for electrons/lithium ions,and special functional groups strongly adsorbing Li PSs.Thus many novel array structured materials are applied to battery for tackling thorny problems mentioned above.In this review,recent progresses and developments on array structured materials applied in LSBs including preparation ways,collaborative structural designs based on array structures,and action mechanism analyses in improving electrochemical performance and safety are summarized.Meanwhile,we also have detailed discussion for array structured materials in LSBs and constructed the structure-function relationships between array structured materials and battery performances.Lastly,some directions and prospects about preparation ways,functional modifications,and practical applications of array structured materials in LSBs are generalized.We hope the review can attract more researchers'attention and bring more studying on array structured materials for other secondary batteries including LSB.

A New Rational-based Optimal Design Strategy of Ship Structure Based on Multi-level Analysis and Super-element Modeling Method

A new multi-level analysis method of introducing the super-element modeling method, derived from the multi-level analysis method first proposed by O. F. Hughes, has been proposed in this paper to solve the problem of high time cost in adopting a rational-based optimal design method for ship structural design. Furthermore,the method was verified by its effective application in optimization of the mid-ship section of a container ship. A full 3-D FEM model of a ship,suffering static and quasi-static loads, was used as the analyzing object for evaluating the structural performance of the mid-ship module, including static strength and buckling performance. Research results reveal that this new method could substantially reduce the computational cost of the rational-based optimization problem without decreasing its accuracy, which increases the feasibility and economic efficiency of using a rational-based optimal design method in ship structural design.

The height-width ratio limited value for rubber bearing isolated structure computed by uniform design method

Rubber isolation is the most mature control technology in practical application, and is widely used by short rigid buildings. However, many high isolation buildings have been built around the world in recent years, which do not follow the existing criterions and codes. Many researchers began to research the special problems caused by larger height-width ratio isolation structures. The overturning effect of high height-width ratio structures with rubber bearing is firstly studied. Considering the main factors, such as the height-width ratio of structures, type of site, the designed basic acceleration of ground motion and the decouple factor in horizon, computing experiment is defined with the Uniform Design Method, which is also known as designing isolation structure. The forces of the bearing under edge of structures based on the position of the rubber bearing are calculated. The result indicates that the rubber bearings will lose its functionality under very high tension and compressing force of earthquake motion in horizon and vertical, when the height-width ratio is over a certain value. Thus, based on the calculation result of isolation structures defined in the uniform design method, regression analysis is conducted, and also the rubber edge force regression formula are gotten, which has higher correlation and smaller standard deviation. This formula can be used to roughly calculate whether the pull force occurs at the edge of the building. By the edge bearings of isolation structure minimum force formula, the height-width ratio limited value of the isolation structure is deducted when rubber bearing has minimum force of zero.

Simplified design method for shear-valve magnetorheological dampers

Based on the Bingham parallel-plate model, a simplified design method of shear-valve magnetorheological （MR） dampers is proposed considering the magnetic circuit optimization. Correspondingly, a new MR damper with a full-length effective damping path is proposed. The prototype dampers are also fabricated and studied numerically and experimentally. According to the test results, the Bingham parallel-plate model is further modified to obtain a damping force prediction model of the proposed MR dampers. This prediction model considers the magnetic saturation phenomenon. The study indicates that the proposed simplified design method is simple, effective and reliable. The maximum damping force of the proposed MR dampers with a full-length effective damping path is at least twice as large as those of conventional MR dampers. The dynamic range of damping force increases by at least 70%. The proposed damping force prediction model considers the magnetic saturation phenomenon and it can realize the actual characteristic of MR fluids. The model is able to predict the actual damping force of MR dampers precisely.

Application of the Modified nverse Design Method in the Optimization of the Runner Blade of a Mixed-Flow Pump

To improve the design speed and reduce the design cost for the previous blade design method, a modified inverse design method is presented. In the new method, after a series of physical and mathematical simplifications, a sail?like constrained area is proposed, which can be used to configure di erent runner blade shapes. Then, the new method is applied to redesign and optimize the runner blade of the scale core component of the 1400?MW canned nuclear coolant pump in an established multi?optimization system compromising the Computational Fluid Dynamics(CFD) analysis, the Response Surface Methodology(RSM) and the Non?dominated Sorting Genetic Algorithm?II(NSGA?II). After the execution of the optimization procedure, three optimal samples were ultimately obtained. Then, through comparative analysis using the target runner blade, it was found that the maximum e ciency improvement reached 1.6%, while the head improvement was about 10%. Overall, a promising runner blade inverse design method which will benefit the hydraulic design of the mixed?flow pump has been proposed.

The Conceptual Design Method for a Pumping Unit Based on QFD and TRIZ

Quality function deployment （QFD） is a quality system, that can help to design novel products that meet customers＇ needs. Theory of inventive problem solving （TRIZ） is a very powerful tool in helping to solve difficult technical problems encountered in the design process. Introducing QFD and TRIZ into the conceptual design of the pumping unit combines advantages of these two theories, therefore meeting different demands of different users. It can tell us “What should we do it” with QFD and “How should we do it” with TRIZ. The conceptual design method, which is based on QFD and TRIZ, is introduced andused to analyze and evaluate the conceptual design project of a pumping unit.

Hydraulic Design Method of Wave Dissipating Structure with Partially Perforated Front Wall

Based on the matching conditions of different fluid regions, the eigenfunction expansion method is used to develop a theoretical formula for wave reflection in front of the perforated structure with a partially slit front wall. The accuracy of the solution is verified by comparing the numerical results with experimental data. In addition, a new hydraulic design method is developed by derivation of the theoretical formula with respect to the porosity of the slit wall, and the results of this design method is drafted for harbour engineers to use.

An alternative practical design method for structures with viscoelastic dampers

Viscoelastic dampers（VEDs） are one of the most common passive control devices used in new and retrofit building projects which reduce the structure responses and dissipate seismic energy during an earthquake.Various methods to design this kind of dampers have been proposed based on the desired level of additional damping,eigenvalue assignment,modal strain energy,linear quadratic regulator control theories,and other approaches.In the current engineering practice,the popular method is the one based on the modal strain energy that uses the inter-story lateral stiffness as one of the main variables for damper design.However,depending on the configuration of the structure,in some cases the resulting interstory lateral stiffness can be very large.Consequently,the dampers size would also be large producing much more damping than that effectively necessary,resulting in an increase of the overall cost of the supplemental damping system and causing excessive stress on the structural elements connected to the dampers.In this paper an alternative practical design method for structures with VEDs is proposed.This method uses the inter-story shear forces as one of the main variables to accomplish the damper design compared to what was done in previous studies.Nonlinear time-history analyses were conducted on a 7-story reinforced concrete（RC） structure to check the reliability and effectiveness of the proposed method.Comparisons on the seismic performance between the structure without dampers and that equipped with VEDs were carried out.It is concluded that the proposed method results in a very suitable size of dampers,which are able to improve the performance of the structure at all levels of earthquake ground motions and satisfying the drift requirement prescribed in the codes.

Probabilistic limit state design methodof the axial resistance of post grouting pile

The reliability of post grouting pile axial resistance was studied by proposing a design method for its probabilistic limit state,which is represented by the partial coefficients of load,end,and side resistance.The hyperbolic,modified hyperbolic,and polynomial models were employed to predict the ultimate bearing capacity of test piles that were not loaded to damage in field tests.The results were used for the calculation and calibration of the reliability index.The reliability of the probabilistic limit state design method was verified by an engineering case.The results show that the prediction results obtained from the modified hyperbolic model are closest to those obtained through the static load test.The proposed corresponding values of total,side,and end resistance partial coefficients are 1.84,1.66,and 2.73 when the dead and live load partial coefficients are taken as 1.1 and 1.4,respectively.Meanwhile,the corresponding partial coefficients of total,side,and end resistance are 1.70,1.56,and 2.34 when the dead and live load partial coefficients are taken as 1.2 and 1.4,respectively.

Design methods of headed studs for composite decks of through steel bridges in high-speed railway

Aimed at two typical composite floor systems of through steel bridges in high speed railway,design methods of headed studs were put forward for different composite members through comparing and analyzing the structure,mechanical characteristics and transmission routes of deck loads.The simplified calculation models were brought out for the stud design of the longitudinal girders and transverse girders in the composite floor system of Nanjing Dashengguan Yangtze River Bridge (NDB).Studs were designed and arranged by taking the middle panel of 336 m main span for example.The results show that under deck loads,the longitudinal girders in the composite floor system of through steel bridges are in tension-bending state,longitudinal shear force on the interface is caused by both longitudinal force of "The first mechanical system" and vertical bending of "The second mechanical system",and studs can be arranged with equal space in terms of the shear force in range of 0.2d (where d is the panel length) on the top ends.Transverse girders in steel longitudinal and transverse girders-concrete slab composite deck are in compound-bending state,and out-of-plane bending has to be taken into account in the stud design.In orthotropic integral steel deck-concrete slab composite deck,out-of-plane bending of transverse girders is very small so that it can be neglected,and studs on the orthotropic integral steel deck can be arranged according to the structural requirements.The above design methods and simplified calculation models have been applied in the stud design of NDB.