Based on the introductions of a type of diaphragm-through connection between concrete-filled square steel tubular columns (CFSSTCs) and H-shaped steel beams,a finite element model of the connection is developed and us...Based on the introductions of a type of diaphragm-through connection between concrete-filled square steel tubular columns (CFSSTCs) and H-shaped steel beams,a finite element model of the connection is developed and used to investigate the seismic behavior of the connection.The results of the finite element model are validated by a set of cyclic loading tests.The cyclic loading tests and the finite element analyses indicate that the failure mode of the suggested connections is plastic hinge at the beam with inelastic rotation angle exceeding 0.04 rad.The suggested connections have sufficient strength,plastic deformation and energy dissipation capacity to be used in composite moment frames as beam-to-column rigid connections.展开更多
Finite element analysis and parametric studies were performed to investigate the flexural capacity of the panel zone of diaphragm-through joints between concretefilled square steel tubular columns and H-shaped steel b...Finite element analysis and parametric studies were performed to investigate the flexural capacity of the panel zone of diaphragm-through joints between concretefilled square steel tubular columns and H-shaped steel beams.Through the comparisons of failure modes,load–displacement curves,and bearing capacity,it was found that the flexural capacity of the panel zone of diaphragmthrough joints was determined by the tensile action and influence of the web of H-shaped steel beams,and the axial load should be taken into account.The steel tube and the diaphragm were the major parts of the joint that resisted the bending moment.The contribution of in-filled concrete had little influence on the flexural capacity of the panel zone of the joint and could be neglected.According to the results of these numerical studies,a formula that considered the influence of the web of H-shaped steel beams and the axial load was developed based on the yield lines in the diaphragm and the steel tube.The results of the proposed formula were in good agreement with the numerical data of this investigation.展开更多
基金Supported by National Natural Science Foundation of China(No.51268054)Natural Science Foundation of Tianjin(No.13JCQNJC07300)the foundation of Key Laboratory of Coast Civil Structure Safety(Tianjin University),Ministry of Education of China(No.2011-1)
文摘Based on the introductions of a type of diaphragm-through connection between concrete-filled square steel tubular columns (CFSSTCs) and H-shaped steel beams,a finite element model of the connection is developed and used to investigate the seismic behavior of the connection.The results of the finite element model are validated by a set of cyclic loading tests.The cyclic loading tests and the finite element analyses indicate that the failure mode of the suggested connections is plastic hinge at the beam with inelastic rotation angle exceeding 0.04 rad.The suggested connections have sufficient strength,plastic deformation and energy dissipation capacity to be used in composite moment frames as beam-to-column rigid connections.
基金supported by the National Natural Science Foundation of China(No.51268054 and No.51468061)Natural Science Foundation of Tianjin,China(No.13JCQNJC07300)
文摘Finite element analysis and parametric studies were performed to investigate the flexural capacity of the panel zone of diaphragm-through joints between concretefilled square steel tubular columns and H-shaped steel beams.Through the comparisons of failure modes,load–displacement curves,and bearing capacity,it was found that the flexural capacity of the panel zone of diaphragmthrough joints was determined by the tensile action and influence of the web of H-shaped steel beams,and the axial load should be taken into account.The steel tube and the diaphragm were the major parts of the joint that resisted the bending moment.The contribution of in-filled concrete had little influence on the flexural capacity of the panel zone of the joint and could be neglected.According to the results of these numerical studies,a formula that considered the influence of the web of H-shaped steel beams and the axial load was developed based on the yield lines in the diaphragm and the steel tube.The results of the proposed formula were in good agreement with the numerical data of this investigation.
