Coupling biomass pretreatment for enzymatic hydrolysis and direct biomass-to-electricity conversion with molybdovanadophosphoric heteropolyacids as anode electron transfer carriers

Owing to their acidity,oxidizing ability and redox reversibility,molybdovanadophosphoric heteropolyacids(H_(n+3)PMo_(12-n)VnO40,abbreviated as PMo_(12-n)Vn) were employed as electron transfer carriers for coupling biomass pretreatment for enzymatic hydrolysis and direct biomass-to-electricity conversion.In this novel coupled process,PMo_(12-n)Vn pretreatment that causes deconstruction of cell wall structure with PMo_(12-n)Vn being simultaneously reduced can be considered as the "charging" process.The reduced PMo_(12-n)Vn are further re-oxidized with release of electrons in a liquid flow fuel cell(LFFC) to generate electricity is the "discharging" process.Several Keggin-type PMo_(12-n)Vn with different degree of vanadium substitution(DSV, namely n) were prepared.Compared to Keggin-type phosphomolybdic acid(PMo_(12)),PMo_(12-n)Vn(n=1-6) showed higher oxidizing ability but poorer redox reversibility.The cellulose enzymatic digestibility of PMo_(12-n)Vn pretreated wheat straw generally decreased with increase in DSV, but xylan enzymatic digestibility generally increased with DSV.PMo_(12) pretreatment of wheat straw at 120℃ obtained the highest enzymatic glucan conversion(EGC) reaching 95%,followed by PMo11V1 pretreatment(85%).Discharging of the reduced heteropolyacids in LFFC showed that vanadium substitution could improve the maximum output power density(Pmax).The highest Pmax was obtained by PMo9 V3(44.7 mW/cm^(2)) when FeCl_(3) was used as a cathode electron carrier,while PMo_(12) achieved the lowest Pmax(27.4 mW/cm^(2)).All the heteropolyacids showed good electrode Faraday efficiency(>95%) and cell discharging efficiency(>93%).The energy efficiency of the coupled process based on the heat values of the products and generated electric energy was in the range of 18%-25% depending on DSV.PMo_(12) and PMo11V1 seem to be the most suitable heteropolyacids to mediate the coupled process.

Effects of direct current electric field on corrosion behaviour of copper, Cl- ion migration behaviour and dendrites growth under thin electrolyte layer

Effect of direct current electric field （DCEF） on corrosion behaviour of copper printed circuit board （PCB-Cu）, Cl-ion migration behaviour, dendrites growth under thin electrolyte layer was investigated using potentiodynamic polarization and scanning electron microscopy （SEM） with energy dispersive spectrometer （EDS）. Results indicate that DCEF decreases the corrosion of PCB-Cu;Cl-ions directionally migrate from the negative pole to the positive pole, and enrich on the surface of the positive pole, which causes serious localized corrosion; dendrites grow on the surface of the negative pole, and the rate and scale of dendrite growth become faster and greater with the increase of external voltage and exposure time, respectively.

Influence of Electric Field Direction on Enhanced Transdermal Delivery of Caffeine by Electroporation

Aim To study the influence of electric field direction on the in vitro enhanced transdermal delivery of caffeine by eleetroporation. Methods Using side-by-side compartment diffusion cells method and Ag-Ag/AgCl electrodes, the transport of caffeine through human cadaver skin by electroporation （exponentially decaying pulse, pulse voltage = 350 V, pulse frequency = 4 pulses· min^-1, capacity = 22 μF, pulse length = 7 ms, 25 pulses） with different electric field directions was carried out and compared with passive diffusion and iontophoresis （0.25 mA·cm^ - 2, lasted for 4 h）. Results （i） The cumulative quantity and flux of caffeine through human skin were increased significantly by eleetroporation or iontophoresis. （ii） The transport of caffeine by positive iontophoresis （ with electric field from donor to receptor compartment） was significantly greater than that by negative iontophoresis （with electric field from receptor to donor compartment）. （iii） The transport of caffeine by positive eleetroporation （with electric field from donor to receptor compartment） was similar to that by negative eleetroporation （with electric field from receptor to donor compartment）. （iv） The enhancing effect of positive iontophoresis on the transdermal delivery of caffeine was significantly greater than that of electroporation （positive or negative）. Conclusion Electric field direction significantly influences the enhancing effect of iontophoresis on the transdermal delivery of caffeine, but does not influence the enhancing effect of eleetroporation.

Direct Ink Writing of Highly Conductive MXene Frames for Tunable Electromagnetic Interference Shielding and Electromagnetic Wave-Induced Thermochromism

The highly integrated and miniaturized next-generation electronic products call for high-performance electromagnetic interference(EMI)shielding materials to assure the normal operation of their closely assembled components.However,the most current techniques are not adequate for the fabrication of shielding materials with programmable structure and controllable shielding efficiency.Herein,we demonstrate the direct ink writing of robust and highly conductive Ti3C2Tx MXene frames with customizable structures by using MXene/AlOOH inks for tunable EMI shielding and electromagnetic wave-induced thermochromism applications.The as-printed frames are reinforced by immersing in AlCl_(3)/HCl solution to remove the electrically insulating AlOOH nanoparticles,as well as cross-link the MXene sheets and fuse the filament interfaces with aluminum ions.After freeze-drying,the resultant robust and porous MXene frames exhibit tunable EMI shielding efficiencies in the range of 25-80 dB with the highest electrical conductivity of 5323 S m−1.Furthermore,an electromagnetic wave-induced thermochromic MXene pattern is assembled by coating and curing with thermochromic polydimethylsiloxane on a printed MXene pattern,and its color can be changed from blue to red under the high-intensity electromagnetic irradiation.This work demonstrates a direct ink printing of customizable EMI frames and patterns for tuning EMI shielding efficiency and visualizing electromagnetic waves.

Single Bubble Behavior in Direct Current Electric Field

The investigation on bubble behavior in electric field helps to analyze the mechanism of electric enhancement of boiling heat transfer. Experiments were performed to investigate the bubble deformation in direct current （DC） electric field with bubbles attached to the orifice. The air bubbles were slowly generated in the transformer oil pool at different orifices, so that the effect of flow on bubble shape was eliminated. The results showed that the bubbles were elongated and the departure volume decreased when the electric field was intensified. The major and minor axes, aspect ratio and departure volume increased with increasing the orifice diameter. Both the electric field and orifice size have great influence on bubble behavior. The bubble deformation was also simulated to compare with the experimental results. The numerical and experimental data qualitatively agree with each other.

Direct Yaw Moment Control for Distributed Drive Electric Vehicle Handling Performance Improvement

For a distributed drive electric vehicle（DDEV） driven by four in-wheel motors, advanced vehicle dynamic control methods can be realized easily because motors can be controlled independently, quickly and precisely. And direct yaw-moment control（DYC） has been widely studied and applied to vehicle stability control. Good vehicle handling performance： quick yaw rate transient response, small overshoot, high steady yaw rate gain, etc, is required by drivers under normal conditions, which is less concerned, however. Based on the hierarchical control methodology, a novel control system using direct yaw moment control for improving handling performance of a distributed drive electric vehicle especially under normal driving conditions has been proposed. The upper-loop control system consists of two parts： a state feedback controller, which aims to realize the ideal transient response of yaw rate, with a vehicle sideslip angle observer; and a steering wheel angle feedforward controller designed to achieve a desired yaw rate steady gain. Under the restriction of the effect of poles and zeros in the closed-loop transfer function on the system response and the capacity of in-wheel motors, the integrated time and absolute error（ITAE） function is utilized as the cost function in the optimal control to calculate the ideal eigen frequency and damper coefficient of the system and obtain optimal feedback matrix and feedforward matrix. Simulations and experiments with a DDEV under multiple maneuvers are carried out and show the effectiveness of the proposed method： yaw rate rising time is reduced, steady yaw rate gain is increased, vehicle steering characteristic is close to neutral steer and drivers burdens are also reduced. The control system improves vehicle handling performance under normal conditions in both transient and steady response. State feedback control instead of model following control is introduced in the control system so that the sense of control intervention to drivers is relieved.

Directional Electromagnetic Interference Shielding Based on Step-Wise Asymmetric Conductive Networks

Some precision electronics such as signal transmitters need to not only emit effective signal but also be protected from the external electromagnetic(EM)waves.Thus,directional electromagnetic interference(EMI)shielding materials(i.e.,when the EM wave is incident from different sides of the sample,the EMI shielding effectiveness(SE)is rather different)are strongly required;unfortunately,no comprehensive literature report is available on this research field.Herein,Nicoated melamine foams(Ni@MF)were obtained by a facile electroless plating process,and multiwalled carbon nanotube(CNT)papers were prepared via a simple vacuum-assisted self-assembly approach.Then,step-wise asymmetric poly(butylene adipate-co-terephthalate)(PBAT)composites consisting of loose Ni@MF layer and compact CNT layer were successfully fabricated via a facile solution encapsulation approach.The step-wise asymmetric structures and electrical conductivity endow the Ni@MF/CNT/PBAT composites with unprecedented directional EMI shielding performances.When the EM wave is incident from Ni@MF layer or CNT layer,Ni@MF-5/CNT-75/PBAT exhibits the total EMI SE(SET)of 38.3 and 29.5 dB,respectively,which illustrates theΔSET of 8.8 dB.This work opens a new research window for directional EMI shielding composites with step-wise asymmetric structures,which has promising applications in portable electronics and next-generation communication technologies.

Reconstruction of electrical capacitance tomography images based on fast linearized alternating direction method of multipliers for two-phase flow system

Electrical capacitance tomography(ECT)has been applied to two-phase flow measurement in recent years.Image reconstruction algorithms play an important role in the successful applications of ECT.To solve the ill-posed and nonlinear inverse problem of ECT image reconstruction,a new ECT image reconstruction method based on fast linearized alternating direction method of multipliers(FLADMM)is proposed in this paper.On the basis of theoretical analysis of compressed sensing(CS),the data acquisition of ECT is regarded as a linear measurement process of permittivity distribution signal of pipe section.A new measurement matrix is designed and L1 regularization method is used to convert ECT inverse problem to a convex relaxation problem which contains prior knowledge.A new fast alternating direction method of multipliers which contained linearized idea is employed to minimize the objective function.Simulation data and experimental results indicate that compared with other methods,the quality and speed of reconstructed images are markedly improved.Also,the dynamic experimental results indicate that the proposed algorithm can ful fill the real-time requirement of ECT systems in the application.

Destruction of an advanced malignant tumour by direct electrical current-case report

We carried out a study on the effect of low-level direct current on cancer by using it to treat a woman who had a large malignant squamous cell carcinoma of the sinus cavity. We used a device that produced low-level direct current and passed the current through the tumour via a 4 × 4 cm flat aluminium foil and a needle electrode that was insulated along its entire length except for the portion actually inserted into the tumour. The treatment was eight hourly daily and lasted for eight weeks. The therapy resulted in the total remission of the tumour and a feeling of wellness by the patient. This finding implies promising therapeutic potential for the use of direct electrical current as a simple, effective, low cost alternative for the treatment of cancer.

Hard magnetization direction and its relation with magnetic permeability of highly grain-oriented electrical steel

The magnetic properties of highly grain-oriented electrical steel vary along different directions. In order to investigate these properties, standard Epstein samples were cut at different angles to the rolling direction. The hard magnetization direction was found at an angle of 60° to the rolling direction. To compare the measured and fitting curves, when the magnetic field intensity is higher than 7000 A/m, it is appropriate to simulate the relation of magnetic permeability and magnetization angle using the conventional elliptical model. When the magnetic field intensity is less than 3000 A/m, parabolic fitting models should be used; but when the magnetic field intensity is between 3000 and 7000 A/m, hybrid models with high accuracy, as proposed in this paper, should be applied. Piecewise relation models of magnetic permeability and magnetization angle are significant for improving the accuracy of electromagnetic engineering calculations of electrical steel, and these new models could be applied in further industrial applications.

Application of direct torque control to electric screw presses for speeding up torque response and reducing starting current

Fast response and stable torque output are crucial to the performance of electric screw presses. This paper describes the design of a direct torque control （DTC） system for speeding up torque response and reducing the starting current of electric screw presses and its application to the J58K series of numerical control electric screw presses with a dual-motor drive. The DTC drive system encompasses speed control, torque reference control, and switching frequency control. Comparison of the DTC dual-AC induction motor drive with corresponding AC servo motor drive showed that for the J58K-315 electric screw press, the DTC drive system attains a higher maximum speed （786 r/min） within a shorter time （1.13 s） during a 250 nun stroke and undergoes smaller rise in temperature （42.0 ℃） in the motor after running for 2 h at a 12 min-1 strike frequency than the AC servo motor drive does （751 r/min within 1.19 s, and 50.6 ℃ rise）. Moreover, the DTC AC induction motor drive, with no need for a tachometer or position encoder to feed back the speed or position of the motor shaft, enjoys increased reliability in a strong-shock work environment.

Mechanical, electrical, and thermal properties of the directionally solidified Bi–Zn–Al ternary eutectic alloy

A Bi-2.0Zn-0.2A1 （wt%） ternary eutectic alloy was prepared using a vacuum melting furnace and a casting furnace. The samples were directionally solidified upwards at a constant growth rate （V= 18.4 μm/s） under different temperature gradients （G = 1.15-3.44 K/mm） and at a constant temperature gradient （G = 2.66 K/mm） under different growth rates （V= 8.3-500 μm/s） in a Bridgman-type directional so- lidification furnace. The dependence ofmicrostructure parameter （2） on the solidification parameters （G and V） and that of the microhardness （Hv） on the microstructure and solidification parameters were investigated. The resistivity （ρ） measurements of the studied alloy were per- formed using the standard four-point-probe method, and the temperature coefficient of resistivity （α） was calculated from the ρ-Tcurve. The enthalpy （AH） and the specific heat （Cp） values were determined by differential scanning calorimetry analysis. In addition, the thermal conductivities of samples, obtained using the Wiedemann-Franz and Smith-Palmer equations, were compared with the experimental results. The results revealed that, the thermal conductivity values obtained using the Wiedemarm-Franz and Smith-Palmer equations for the Bi-2.0Zn-0.2Al （wt%） alloy are in the range of 5.2-6.5 W/Km and 15.2-16.4 W/Km, respectively.

Electrical Impedance Tomography Based on Direct Search Method

Solution to impedance distribution in electrical impedance tomography （EIT） is an ill-posed nonlinear inverse problem. It is especially difficult to reconstruct an EIT image in the center area of a measured object. Tikhonov regularization with some prior information is a sound regnlarization method for static electrical impedance tomography under the condition that some true impedance distribution information is known a priori. This paper presents a direct search method （DSM） as pretreatment of image reconstruction through which one not only can construct a regularization matrix which may locate in areas of impedance change, but also can obtain an initial impedance distribution more similar to the true impedance distribution, as well as better current modes which can better distinguish the initial distribution and the true distribution. Simulation results indicate that, by using DSM, resolution in the center area of the measured object can be improved significantly.

Dependence of microstructural, mechanical and electrical properties on growth rates in directional solidified Zn-Al-Bi eutectic alloy

Zn-5%Al-0.2%Bi（mass fraction） alloy was directionally solidified upward at a constant temperature gradient with a wide range of growth rates using a Bridgman-type directional solidification furnace. The eutectic spacings, microhardness, ultimate tensile strength and electrical resistivity for directionally solidified Zn-Al-Bi alloy were measured. Dependence of eutectic spacings, microhardness, ultimate tensile strength and electrical resistivity on growth rates was obtained by linear regression analysis. The results obtained in the present work for low growth rates（smaller than 450.0 μm/s） are in good agreement with experimental results obtained in previous work for directional solidified Zn-Al eutectic alloy with a similar growth rate but differs from the Jackson-Hunt eutectic theory and those obtained in previous experimental works at higher growth rates. The critical growth rate might be 450.0 μm/s for the Zn-Al-Bi eutectic alloy. From the plot of heat flow versus temperature, enthalpy of fusion, specific heat difference between liquid and solid phases and melting temperature for the Zn-Al-Bi alloy are found to be 112.55 J/g, 0.291 J/（g·K） and 660.20 K, respectively.

Periodic transparent nanowires in ITO film fabricated via femtosecond laser direct writing

This paper reports the fabrication of regular large-area laser-induced periodic surface structures(LIPSSs)in indium tin oxide(ITO)films via femtosecond laser direct writing focused by a cylindrical lens.The regular LIPSSs exhibited good properties as nanowires,with a resistivity almost equal to that of the initial ITO film.By changing the laser fluence,the nanowire resistances could be tuned from 15 to 73 kΩ/mm with a consistency of±10%.Furthermore,the average transmittance of the ITO films with regular LIPSSs in the range of 1200-2000 nm was improved from 21%to 60%.The regular LIPSS is promising for transparent electrodes of nano-optoelectronic devices-particularly in the near-infrared band.

THE ELECTRIC PROPERTY OF SINGLET CARBENE AND ITS ISOELECTRONIC SYSTEM^1——Electrophilic and Nucleophilic Directions of an Atom in the Molecule

The electrostatic potential of carbene and nitrene,have been calculated by AB INITIO method with 6-31G** basis set,there are positive potential regions in the directions of vacant P orbitals,and negative regions in the directions of lone-pair electrons. Therefore,atoms in these molecules have different electric properties in different directions.The idea of electrophilic and nucleophilic directions of an atom in molecules should be introduced.

Hydrophobic ionic liquids/water interfacial phase transfer induced by direct current electric field

To investigate the affect of direct current electric field (DCEF) on the interfacial phase,in this paper,a hydrophobic ionic liquid (HIL)/water as liquid-liquid two-phase binary system is established by using the deioned water and l-butyl-3-methyl imidazolium hexafluorophosphate,and the topographies of the HIL nanodroplets and nanolayers in ambient water are observed by atomic force microscope (AFM).The results show the AFM exerting the DCEF can enhance the intersolubility of the HIL/water binary system and induce their interfacial phase transfer.

不同电学参数和水流条件下电栅对鲤(Cyprinus carpio)的阻拦效果

脉冲直流电导阻鱼技术已被广泛应用于阻止入侵物种扩散、驱赶鱼类远离危险区域并将其引导至有利区域,如鱼道。但是脉冲直流电的有效性受多方面因素的影响,其主导因素目前尚未定论。以鲤为研究对象,在静水条件下采用4因素3水平正交实验方法分析了脉冲电压、脉冲宽度、脉冲频率和电极摆放方式的电栅拦鱼效果及其对鱼类受伤尾数的主次影响,然后选择最优组合开展不同流速下(0,0.3,0.5 m/s)的驱鱼实验,分析流速对拦鱼效果的影响。结果表明:在静水工况下,影响拦鱼电栅效率的主要因素为电极布置方式>脉冲宽度>脉冲频率>脉冲电压,电极布置为方式1(垂直水流间距80 cm)、脉冲电压140 V、脉冲频率10 Hz、脉冲宽度10 ms是拦鱼效果最佳的组合。电学参数对鲤的伤害无显著性,平均受伤尾数不超过实验鱼总数的15%。流水条件下,三种流速工况下拦鱼电栅的阻拦率无显著差异,但是随着流速的增高阻拦率呈现先降低后增加的趋势。该研究将为保护鱼类资源和防止入侵鱼类跨区域传播提供依据。

偏差电量考核机制下聚合温控负荷群控制策略

为降低售电公司在电力交易中的偏差考核电量和惩罚成本,以在用户负荷中占比较高的温控负荷为控制对象,建立配电网监测控制系统,收集电力市场和居民负荷数据,再根据这些数据设计基于聚合温控负荷群双层优化调度模型的直接负荷控制策略。仿真结果表明,该策略能降低配电网功率不平衡性,有效增加温控负荷的可调度容量,减少温控负荷的调度次数,降低售电公司的偏差考核电量,提高售电公司利润。

考虑异步通信的配电-气网分布式有功-无功协同优化

配电-气网(EGDN)中新能源大量并网和燃气运输过程中管网压力变化均可能导致配电网的电压波动增大。文中提出一种考虑异步通信的EGDN有功-无功协同优化方法。首先,研究EGDN中各元件的有功-无功特性;其次,根据EGDN能量运输过程中无功需求特性,建立EGDN无功供需模型;然后,考虑EGDN无功平衡和网络运行约束,以最小化电网电压波动、网损和EGDN购电/气成本为目标,建立EGDN无功电压优化控制模型;最后,为保障EGDN中各能源主体信息的安全性与私密性,考虑配电网与配气网信息采集传输情况存在差异,可能存在通信延迟和信息丢包情况,采用异步交替方向乘子法对模型进行求解。通过对改进的IEEE 33节点系统和7节点配气网构成的EGDN系统进行仿真,结果表明,所提方法可有效缓解EGDN电压波动问题,减小网损并降低系统总运行成本。