A low-cost invasive microwave ablation antenna with a directional heating pattern

Microwave ablation(MWA) is a cancer treatment method. The tumor tissue absorbs electromagnetic energy, which heats and kills it. A microwave ablation antenna plays a critical role in this process. Its radiation field must completely cover the tumor but not the healthy tissue. At present, the radiation pattern of most invasive ablation antennas is spherical.However, in the clinic, the shape of some tumors may be asymmetrical or the antenna cannot be inserted into the center of the tumor for some other reason. In order to solve these problems, a directional heating antenna for microwave ablation is proposed in this paper. The proposed antenna, operating at 2.45 GHz, consists of a monopole and a reflector. The feed is given by a substrate integrated coaxial line(SICL) and coplanar waveguide(CPW). The omnidirectional radiation field of the monopole is reflected by a reflector that is extended from the outer conductors of the SICL to form a directional radiation field. The impedance matching network is designed on SICL to match the antenna to 50 Ω. The antenna is fabricated using a mature printed circuit board(PCB). The reflection coefficient of the antenna in porcine liver tissue measured by a vector network analyzer shows good agreement with the simulations. Then, an ablation experiment in porcine liver is conducted with power of 10 W for 10 min, and the experimental results confirm the validity of the design.

Radiation heat transfer model for complex superalloy turbine blade in directional solidification process based on finite element method

For the sake of a more accurate shell boundary and calculation of radiation heat transfer in the Directional Solidification(DS) process, a radiation heat transfer model based on the Finite Element Method(FEM)is developed in this study. Key technologies, such as distinguishing boundaries automatically, local matrix and lumped heat capacity matrix, are also stated. In order to analyze the effect of withdrawing rate on DS process,the solidification processes of a complex superalloy turbine blade in the High Rate Solidification(HRS) process with different withdrawing rates are simulated; and by comparing the simulation results, it is found that the most suitable withdrawing rate is determined to be 5.0 mm·min^(-1). Finally, the accuracy and reliability of the radiation heat transfer model are verified, because of the accordance of simulation results with practical process.

Directional solidification and physical properties measurements of the zinc-aluminum eutectic alloy

Zn-5wt% Al eutectic alloy was directionally solidified with different growth rates （5.32-250.0μm/s） at a constant temperature gradient of 8.50 K/mm using a Bridgman-type growth apparatus.The values of eutectic spacing were measured from transverse sections of the samples.The dependences of the eutectic spacing and undercooling on growth rate are determined as λ=9.21V-0.53 and ΔT=0.0245V0.53,respectively.The results obtained in this work were compared with the Jackson-Hunt eutectic theory and the similar experimental results in the literature.Microhardness of directionally solidified samples was also measured by using a microhardness test device.The dependency of the microhardness on growth rate is found as Hv=115.64V0.13.Afterwards,the electrical resistivity （r） of the casting alloy changes from 40×10-9 to 108×10-9 Ω·m with the temperature rising in the range of 300-630 K.The enthalpy of fusion （ΔH） and specific heat （Cp） for the Zn-Al eutectic alloy are calculated to be 113.37 J/g and 0.309 J/（g·K）,respectively by means of differential scanning calorimetry （DSC） from heating trace during the transformation from liquid to solid.

CFD Simulations of Wind Effect on Net Solar Heat Gain of South Walls with Internal Insulation

Computational fluid dynamics( CFD) techniques are used to investigate effects of both wind direction and wind speed on net solar heat gain of south wall with internal insulation in winter.Results show that wind effect has a significant influence on the net solar heat gain,where the impact of wind direction is stronger than that of wind speed. For regions in lower reaches of the Yangtze River,difference of their average net solar heat gains( NSHGS) is about 20% due to various wind speeds and wind directions.Buildings in districts with a dominant wind direction of north achieve the highest solar energy utilization.

Experimental Study on Latent Heat Storage Characteristics of W/O Emulsion-Supercooling Rate of Dispersed Water Drops by Direct Contact Heat Exchange

Recently, much attention has been paid to investigate the latent heat storage system. Using of ice heat storage system brings an equalization of electric power demand, because it will solved the electric -power-demand-concentration on day-time of summer by the air conditioning. The flowable latent heat storage material, Oil/Water type emulsion, microencapsulated latent heat material-water mixture or ice slurry, etc., is enable to transport the latent heat in a pipe. The flowable latent heat storage material can realize the pipe size reduction and system efficiency improvement. Supercooling phenomenon of the dispersed latent heat storage material in continuous phase brings the obstruction of latent heat storage. The latent heat storage rates of dispersed water drops in W/O (Water/Oil) emulsion are investigated experimentally in this study. The water drops in emulsion has the diameter within 3 ~ 25μm, the averaged water drop diameter is 7.3μm and the standard deviation is 2.9μm. The direct contact heat exchange method is chosen as the phase change rate evaluation of water drops in W/O emulsion. The supercooled temperature and the cooling rate are set as parameters of this study. The evaluation is performed by comparison between the results of this study and the past research. The obtained experimental result is shown that the 35K or more degree from melting point brings 100% latent heat storage rate of W/O emulsion. It was clarified that the supercooling rate of dispersed water particles in emulsion shows the larger value than that of the bulk water.

Interaction phenomena between liquid droplets and hot particles—Captured via high-speed camera

The interaction of evaporating droplets and hot catalyst particles plays a major role in heterogeneously catalysed reactions. The liquid feed is injected into a gas-solid flow and is mixed with the catalyst. The interaction phenomena determine the evaporation time which should be minimised to keep the reactor vessel small. First measurements with a bed of fixed hot FCC-particles （fluid catalytic cracking） and two model fluids have been conducted. The interactions of ethanol and water droplets with the hot bed surface were captured via a high-speed camera. While the ethanol droplet developed a stable steam cushion due to Leidenfrost phenomena, water showed intense interaction and steam explosions which induced repulsion and atomisation of the droplet.