Thruster direction controlling of assembled spacecraft based on gimbal suspension

The attitude control system design and its control effect are affected considerably by the mass-property parameters of the spacecraft. In the mission of on-orbit servicing, as fuel is expended, or the payloads are added or removed, the center of mass will be changed in certain axe; consequently, some thrusters＇ directions are deviated from the center of mass（CM） in certain plane. The CM of assembled spacecraft estimation and thruster direction control are studied. Firstly, the attitude dynamics of the assembled spacecraft is established based on the Newton-Euler method. Secondly, the estimation can be identified by the least recursive squares algorithm. Then, a scheme to control the thrusters＇ directions is proposed. By using the gimbal installed at the end of the boom, the angle of the thruster is controlled by driving the gimbal; therefore, thrusters can be directed to the CM again. Finally, numerical simulations are used to verify this scheme. Results of the numerical simulations clearly show that this control scheme is rational and feasible.

Laboratory Implementation of Direct Torque Controller based Speed Loop Pseudo Derivative Feedforward Controller for PMSM Drive

This paper,evaluate the effectiveness of a proposed speed loop pseudo derivative feedforward(PDFF)controller-based direct torque controller(DTC)for a PMSM drive against the performance of existing PI speed controller-based DTC and hysteresis current controller(HCC).The proposed PDFF-based speed regulator effectively reduces oscillation and overshoot associated with rotor angular speed,electromagnetic torque,and stator current.Two case studies,one using forward-to-reverse motoring operation and the other involving reverse-to-forward braking operation,has been validated to show the effectiveness of the proposed control strategy.The proposed controller's superior performance is demonstrated through experimental verification utilizing an FPGA controller for a 1.5 kW PMSM drive laboratory prototype.

Genetic algorithm and particle swarm optimization tuned fuzzy PID controller on direct torque control of dual star induction motor

This study presents analysis, control and comparison of three hybrid approaches for the direct torque control (DTC) of the dual star induction motor (DSIM) drive. Its objective consists of combining three different heuristic optimization techniques including PID-PSO, Fuzzy-PSO and GA-PSO to improve the DSIM speed controlled loop behavior. The GA and PSO algorithms are developed and implemented into MATLAB. As a result, fuzzy-PSO is the most appropriate scheme. The main performance of fuzzy-PSO is reducing high torque ripples, improving rise time and avoiding disturbances that affect the drive performance.

Controlled Secure Direct Communication Protocol via the Three-Qubit Partially Entangled Set of States

In this paper,we first re-examine the previous protocol of controlled quantum secure direct communication of Zhang et al.’s scheme,which was found insecure under two kinds of attacks,fake entangled particles attack and disentanglement attack.Then,by changing the party of the preparation of cluster states and using unitary operations,we present an improved protocol which can avoid these two kinds of attacks.Moreover,the protocol is proposed using the three-qubit partially entangled set of states.It is more efficient by only using three particles rather than four or even more to transmit one bit secret information.Given our using state is much easier to prepare for multiqubit states and our protocol needs less measurement resource,it makes this protocol more convenient from an applied point of view.

Analysis and Improvement of an Efficient Controlled Quantum Secure Direct Communication and Authentication Protocol

The controlled quantum secure direct communication(CQSDC)with authentication protocol based on four particle cluster states via quantum one-time pad and local unitary operations is cryptanalyzed.It is found that there are some serious security issues in this protocol.An eavesdropper(Eve)can eavesdrop on some information of the identity strings of the receiver and the controller without being detected by the selective-CNOT-operation(SCNO)attack.By the same attack,Eve can also steal some information of the secret message that the sender transmits.In addition,the receiver can take the same kind of attack to eavesdrop on some information of the secret message out of the control of the controller.This means that the requirements of CQSDC are not satisfied.At last,we improve the original CQSDC protocol to a secure one.

A novel fuzzy logic direct torque controller for a permanent magnet synchronous motor with a field programmable gate array

A high-performance digital servo system built on the platform of a field programmable gate array (FPGA),a fully digitized hardware design scheme of a direct torque control (DTC) and a low speed permanent magnet synchronous motor (PMSM) is proposed. The DTC strategy of PMSM is described with Verilog hardware description language and is employed on-chip FPGA in accordance with the electronic design automation design methodology. Due to large torque ripples in low speed PMSM,the hysteresis controller in a conventional PMSM DTC was replaced by a fuzzy controller. This FPGA scheme integrates the direct torque controller strategy,the time speed measurement algorithm,the fuzzy regulating technique and the space vector pulse width modulation principle. Experimental results indicate the fuzzy controller can provide a controllable speed at 20 r min-1 and torque at 330 N m with satisfactory dynamic and static performance. Furthermore,the results show that this new control strategy decreases the torque ripple drastically and enhances control performance.

Robust H_∞ directional control for a sampled-data autonomous airship

A robust H∞ directional controller for a sampled-data autonomous airship with polytopic parameter uncertainties was proposed. By input delay approach, the linearized airship model was transformed into a continuous-time system with time-varying delay. Sufficient conditions were then established based on the constructed Lyapunov-Krasovskii functional, which guarantee that the system is mean-square exponentially stable with H∞ performance. The desired controller can be obtained by solving the obtained conditions. Simulation results show that guaranteed minimum H∞ performance γ=1.4037 and fast response of attitude for sampled-data autonomous airship are achieved in spite of the existence of parameter uncertainties.

Practical prescribed-time tracking control for uncertain strict-feedback systems with guaranteed performance under unknown control directions

In this paper,we consider the practical prescribed-time performance guaranteed tracking control problem for a class of uncertain strict-feedback systems subject to unknown control direction.Due to the existence of unknown nonlinearities and uncertainties,it is challenging to design a controller that can ensure the stability of closed-loop system within a predetermined finite time while maintaining the specified transient performance.The underlying problem becomes further complex as the control directions are unknown.To deal with the above problems,a special translation function as well as Nussbaum type function are introduced in the prescribed performance control(PPC)framework.Finally,a PPC as well as preset finite time tracking control scheme is designed,and its effectiveness is confirmed by both theoretical analysis and numerical simulation.

Directional region control of the thermal fractal diffusion of a space body

We present a directional region control （DRC） model of thermal diffusion fractal growth with active heat diffusion in three-dimensional space. This model can be applied to predict the space body heat fractal growth and study its directional region control. When the nonlinear interference term and the inner heat source term are generalized functions, the relationship between the particle aggregation probability and the interference terms can be obtained using the norm theory. We can then predict the aggregation form of particles in different regions. When the nonlinear interference terms in the model are expressed as a trigonometric function and its composite function, our simulations show that the DRC method of thermal fractal diffusion is effective and has reference value for the directional control of actual fractal growth systems.

A Control of Uncertain Nonlinear Systems with Unknown Control Direction Via Adaptive Backstepping

The adaptive stabilization problem of nonlinear systems are studied. For a class of uncertain nonlinear systems with unknown control direction, we proposed a robust adaptive backstepping scheme withσ-modification by introducing Nussbaum function and Backstep- ping methods, and proved that all the signals of the closed-loop systems are bounded.

Arc deflection model and arc direction control for DC arc furnace

Based on the analysis of three-dimensional power conductor for DC arcfurnace, the electric arc deflection model was set up and the control system of the arc directionwas configured. According to the bus bar distribution at the bottom electrodes cooled by water, thearc direction control principle and its configuration were described. The simulation results showthat the control system can restrain the electric arc deflection and control the arc direction.

Call for Papers:Special Issue on "Recent Advances and New Directions in Switched Control Systems" ——Jounal of Control Theory and Application

Recently, switched control systems have been attracting much attention m the control community because the problems are not only academically challenging for the inherent complexity, but also of practical importance due to its wide ranges of applications in nature, engineering, and social sciences.

Comparative Study of the DTC-IM Speed Controller Based on Artificial Intelligence

Recently, artificial intelligence technique is increasingly receiving attention in solving complex and practical problem and they are widely applying in electrical machine domain. The authors consider also the direct torque control （DTC） as an alternative to conventional methods of control by pulse width modulation （PWM） and by Field oriented control （FOC）, so the application of the DTC based on artificial intelligence can show more advantages and simplified control algorithms with high performance. For this reason, the objectives of this paper can be divided into two parts, the first part is to apply neural networks and fuzzy logic techniques to the DTC control in the presence of a loop speed control comparing to the conventional regulators （as PI） to show the feasibility of these approaches, the second part is to further improve the performance of the neural network by using a neural-fuzzy regulator which combine the advantages of two techniques. Simulation results confirm the validity of the proposed techniques.

Controlling the Directed Quantum Transport of Ultracold Atoms in an Optical Lattice with a Periodic Driving Field

We propose a new method to control the directed quantum transport of ultracold atoms in a one-dimensional optical lattice. In this proposal, the effective tunneling between the neighboring sites can be adjusted via coherent destruction of tunneling by tuning the phase of the external field, instead of using the driving field intensity or the frequency, thus the directed quantum transport of ultracold atoms can be coherently controlled in a nmch easier manner. Our proposal overcomes the major drawback of the method used by Creffield et al [Phys. Rev. Lett. 99 （2007） 110501], and can be implemented, in principle, in any one-dimensional optical lattice. Some potential applications of the scheme are also discussed.

Special Issue on Recent Advances and New Directions in Switched Control Systems

As guest editors, it is our great honor to bring this special issue of the Journal of Control Theory and Applications devoted to Recent Advances and New Directions in Switched Control Systems.

An Improved Proportional Integral Estimator of the Stator Resistance for a Direct Torque Controlled Induction Motor

In this paper, an improved PI （proportional integral） stator resistance estimation for a DTC （direct torque controlled） induction motor is proposed. This estimation method is based on an on-line stator resistance correction regarding the variations of the stator current estimation error. In fact, the input variable of the P1 estimator is the stator current estimation error. The main idea is to tune accurately the stator resistance value relatively to the evolution of the stator current estimation error gradient to avoid the drive instability and ensure the tracking of the actual value of the stator resistance. But there is an unavoidable steady state error between the filtered stator current modulus and its estimated value from the dq model of the machine which is due to pseudo random commutations of the inverter switches. This may deteriorate the performance of the proposed fuzzy stator resistance estimator. An offset has been introduced in order to overcome this problem, for different speed command values and load torques. Simulation results show that the proposed estimator was able to successfully track the actual value of the stator resistance lbr different operating conditions.

A Novel Multilevel Inverter Circuit for the Performance Enhancement of Direct Torque Controlled Induction Motor

Induction motor is the most sought after motor in the industry for excellent performance characteristics and robustness. Developments in the Power Electronic circuitry have revolutionised the induction motor industry leading to the developments in various control strategies and circuits for motor control. Direct Torque Control (DTC) is one of the excellent control strategies preferred by industries for controlling the torque and flux in an induction machine. The main drawback of DTC is the presence of torque ripple which is slightly more than the acceptable limit. There are various parameters that introduce ripples in the electromagnetic torque, one of them being the type of inverter circuit. There are various types of inverter circuits available and the effect of each of them in the production of torque ripple is different. This work is an attempt to identify the influence of various multilevel inverter circuits on the torque ripple level and to propose the best inverter circuit. The influence of multilevel diode clamped inverter and cascaded H bridge inverter circuits on torque ripple minimization, is analysed using simulation studies for identifying the most suitable multilevel inverter circuit which gives minimum torque ripple. The results obtained from the simulation studies are validated by hardware implementation on 0.75 kW induction motor.

BOOSTING SPARSE LEAST SQUARES SUPPORT VECTOR REGRESSION (BSLSSVR) AND ITS APPLICATION TO THRUST ESTIMATION

In order to realize direct thrust control instead of conventional sensors-based control for aero-engine, a thrust estimator with high accuracy is designed by using the boosting technique to improve the performance of least squares support vector regression （LSSVR）. There exist two distinct features compared with the conven- tional boosting technique： （1） Sampling without replacement is used to avoid numerical instability for modeling LSSVR. （2） To realize the sparseness of LSSVR and reduce the computational complexity, only a subset of the training samples is used to construct LSSVR. Thus, this boosting method for LSSVR is called the boosting sparse LSSVR （BSLSSVR）. Finally, simulation results show that BSLSSVR-based thrust estimator can satisfy the requirement of direct thrust control, i.e. , maximum absolute value of relative error of thrust estimation is not more than 5‰.

Design and Development of the DTC Induction Motor Drive for Electric Vehicle

The design and development of the traction controller for electric vehicle is introduced, which is based on the induction motor. This drive is developed by using a digital signal processor at low cost and carried out with the module design concept of both software and hardware. Nevertheless, a scheme of the sensorless direct torque control is based on the developed hardware, of which the feasibility is tested by a trial program. Additionally, both the interface function of the drive hardware and the feasibility of its software are proved to be good by the trail programs. A test motor can run about 18?r/min by a variable frequency program with the space vector pulse width modulation technology, of which the torque is visible pulsatile. In this presentation, based on the theoretical approach, the sensorless torque control is to be studied and applied to electric vehicles, of which the quick, smooth and stable torque response is emphasized because it quite benefits improving the drive performance of electric vehicles.

Dynamic simulation and optimal control strategy for a parallel hybrid hydraulic excavator

The primary focus of this study is to investigate the control strategies of a hybrid system used in hydraulic excavators. First, the structure and evaluation target of hybrid hydraulic excavators are analyzed. Then the dynamic system model including batteries, motor and engine is built as the simulation environment to obtain control results. A so-called multi-work-point dynamic control strategy, which has both closed-loop speed PI (proportion integral) control and direct torque control, is proposed and studied in the simulation model. Simulation results indicate that the hybrid system with this strategy can meet the power demand and achieve better system stability and higher fuel efficiency.