Impact Force Localization and Reconstruction via ADMM-based Sparse Regularization Method

In practice,simultaneous impact localization and time history reconstruction can hardly be achieved,due to the illposed and under-determined problems induced by the constrained and harsh measuring conditions.Although l_(1) regularization can be used to obtain sparse solutions,it tends to underestimate solution amplitudes as a biased estimator.To address this issue,a novel impact force identification method with l_(p) regularization is proposed in this paper,using the alternating direction method of multipliers(ADMM).By decomposing the complex primal problem into sub-problems solvable in parallel via proximal operators,ADMM can address the challenge effectively.To mitigate the sensitivity to regularization parameters,an adaptive regularization parameter is derived based on the K-sparsity strategy.Then,an ADMM-based sparse regularization method is developed,which is capable of handling l_(p) regularization with arbitrary p values using adaptively-updated parameters.The effectiveness and performance of the proposed method are validated on an aircraft skin-like composite structure.Additionally,an investigation into the optimal p value for achieving high-accuracy solutions via l_(p) regularization is conducted.It turns out that l_(0.6)regularization consistently yields sparser and more accurate solutions for impact force identification compared to the classic l_(1) regularization method.The impact force identification method proposed in this paper can simultaneously reconstruct impact time history with high accuracy and accurately localize the impact using an under-determined sensor configuration.

Study on distribution rule of sliding pushing force and remnant resistant sliding force acting on anti-sliding pile

Anti-slide pile is one of the important methods to administer landslide geological disaster because of its advantages.It plays important role in administering landslide.It is a premise of reasonable economy and technological advance to know the distribution rule and feature of the force between anti-sliding pile and surrounding rock.To determine the sliding force and remnant resistant sliding force,according to need of study,this paper sets up the geological model and mechanics model in term of a typical landslide,and analyzes the effect rule of sliding body distortion,strength and gravity to the pushing force and remnant resistant sliding force by use of the numerical model.The distribution rule of pushing force and remnant resistant sliding force of the type of landslide is given.

Volume, Side-Area, and Force Direction of Berkovich and Cubecorner Indenters, Novel Important Insights

The iteration-free physical description of pyramidal indentations with closed mathematical equations is comprehensively described and extended for creating new insights in this important field of research and applications. All calculations are easily repeatable and should be programmed by instrument builders for even easier general use. Formulas for the volumes and side-areas of Berkovich and cubecorner as a function of depth are deduced and provided, as are the resulting forces and force directions. All of these allow for the detailed comparison of the different indenters on the mathematical reality. The pyramidal values differ remarkably from the ones of so-called “equivalent cones”. The worldwide use of such pseudo-cones is in severe error. The earlier claimed and used 3 times higher displaced volume with cube corner than with Berkovich is disproved. Both displace the same amount at the same applied force. The unprecedented mathematical results are experimentally confirmed for the physical indentation hardness and for the sharp-onset phase-transi- tions with calculated transition energy. The comparison of both indenters provides novel basic insights. Isotropic materials exhibit the same phase transition onset force, but the transition energy is larger with the cube corner, due to higher force and flatter force direction. This qualifies the cube corner for fracture toughness studies. Pile-up is not from the claimed “friction with the indenter”. Anisotropic materials with cleavage planes and channels undergo sliding along these under pressure, both to the surface and internally. Their volumes add to the depression volume. These volumes are essential for the exemplified pile-up management. Phase-transitions produce polymorph interfaces that are nucleation sites for cracks. Technical materials must be developed with onset forces higher than the highest thinkable stresses (at airliners, bridges, etc.). This requires urgent revision of ISO 14577-ASTM standards.

An evaluation of force-based design vs.direct displacement-based design of jointed precast post-tensioned wall systems

The unique features of jointed post-tensioned wall systems, which include minimum structural damage and re-centering capability when subjected to earthquake lateral loads, are the result of using unbonded post-tensioning to attach the walls to the foundation, along with employing energy dissipating shear connectors between the walls. Using acceptance criteria defined in terms of inter-story drift, residual drift, and floor acceleration, this study presents a multiplelevel performance-based seismic evaluation of two five-story unbonded post-tensioned jointed precast wall systems. The design and analysis of these two wall systems, established as the direct displacement-based and force-based solutions for a prototype building used in the PREcast Seismic Structural Systems （PRESSS） program, were performed at 60% scale so that the analysis model could be validated using the PRESSS test data. Both buildings satisfied the performance criteria at four levels of earthquake motions although the design base shear of the direct displacement-based jointed wall system was 50% of that demanded by the force-based design method. The study also investigated the feasibility of controlling the maximum transient inter-story drift in a jointed wall system by increasing the number of energy dissipating shear connectors between the walls but without significantly affecting its re-centering capability.

Direct numerical simulation on relevance of fluctuating velocities and drag reduction in turbulent channel flow with spanwise space-dependent electromagnetic force

Based on the Fourier–Chebyshev spectral method, the control of turbulent channel flow by space-dependent electromagnetic force and the mechanism of drag reduction are investigated with direct numerical simulation(DNS) methods for different Reynolds numbers. A formula is derived to express the relation between fluctuating velocities and the friction drag coefficient. With the application of electromagnetic force, the in-depth relations among the fluctuating velocities near the wall, Reynolds stress, and the effect of drag reduction for different Reynolds numbers are discussed. The results indicate that the maximum drag reductions can be obtained with an optimal combination of parameters for each case of different Reynolds numbers. The fluctuating velocities along the streamwise and normal directions are suppressed significantly,while the fluctuating velocity along the spanwise direction is enhanced dramatically due to the spanwise electromagnetic force. However, the values of Reynolds stress depend on the fluctuating velocities along the streamwise and normal directions rather than that along the spanwise direction. Therefore, the significant effect of drag reduction is obtained. Moreover,the maximum drag reduction is weakened due to the decay of control effect for fluctuating velocities as the Reynolds number increases.

Applying Force-Directed Placer to Wafer Scale Placement

A placement algorithm for discretionary wiring WSI system, WFDP, is proposed in this paper. WFDP employes force-directed placement algorithm. First the relative locations of macro circuit component are determined. In the phase of determining the real location of the circuit component, it avoids the problem of determining the real location of arbitrary component by employing divide-conquer strategy and removing the hierarchical division. Its computation is much more simpler than other homologous algorithm. A simple model used to estimate the quality of placement is also proposed. Although the WFDP is aimed at WSI, it can also be used in the placement of other redundancy-oriented device or system such as RVLSI, etc.

A Study on Sulfate Optical Properties and Direct Radiative Forcing Using LASG-IAP General Circulation Model

The direct radiative forcing （DRF） of sulfate aerosols depends highly on the atmospheric sulfate loading and the meteorology, both of which undergo strong regional and seasonal variations. Because the optical properties of sulfate aerosols are also sensitive to atmospheric relative humidity, in this study we first examine the scheme for optical properties that considers hydroscopic growth. Next, we investigate the seasonal and regional distributions of sulfate DRF using the sulfate loading simulated from NCAR CAM-Chem together with the meteorology modeled from a spectral atmospheric general circulation model （AGCM） developed by LASG-IAP. The global annual-mean sulfate loading of 3.44 mg m-2 is calculated to yield the DRF of -1.03 and -0.57 W m-2 for clear-sky and all-sky conditions, respectively. However, much larger values occur on regional bases. For example, the maximum all-sky sulfate DRF over Europe, East Asia, and North America can be up to -4.0 W m-2. The strongest all-sky sulfate DRF occurs in the Northern Hemispheric July, with a hemispheric average of -1.26 W m-2. The study results also indicate that the regional DRF are strongly affected by cloud and relative humidity, which vary considerably among the regions during different seasons. This certainly raises the issue that the biases in model-sinmlated regional meteorology can introduce biases into the sulfate DRF. Hence, the model processes associated with atmospheric humidity and cloud physics should be modified in great depth to improve the simulations of the LASG-IAP AGCM and to reduce the uncertainty of sulfate direct effects on global and regional climate in these simulations.

Mechanism of controlling turbulent channel flow with the effect of spanwise Lorentz force distribution

A direct numerical simulation（DNS） is performed to investigate the control effect and mechanism of turbulent channel flow with the distribution of spanwise Lorentz force. A sinusoidal distribution of constant spanwise Lorentz force is selected, of which the control effects, such as flow characters, mean Reynolds stress, and drag reductions, at different parameters of amplitude A and wave number k_x are discussed. The results indicate that the control effects vary with the parameter A and k_x. With the increase of A, the drag reduction rate D_r first increases and then decreases rapidly at low k_x,and slowly at high k_x. The low drag reduction（or even drag increase） is due to a weak suppression or even the enhancements of the random velocity fluctuation and mean Reynolds stress. The efficient drag reduction is due to the quasi-streamwise vortex structure induced by Lorentz force, which contributes to suppressing the random velocity fluctuation and mean Reynolds stress, and the negative vorticity improves the distribution of streamwise velocity. Therefore, the optimal control effect with a drag reduction of up to 58% can be obtained.

Grid-cell Aerosol Direct Shortwave Radiative Forcing Calculated Using the SBDART Model with MODIS and AERONET Observations：An Application in Winter and Summer in Eastern China

Taking winter and summer in eastern China as an example application, a grid-cell method of aerosol direct radiative forcing（ADRF） calculation is examined using the Santa Barbara DISORT Atmospheric Radiative Transfer（SBDART） model with inputs from MODIS and AERONET observations and reanalysis data. Results show that there are significant seasonal and regional differences in climatological mean aerosol optical parameters and ADRF. Higher aerosol optical depth（AOD）occurs in summer and two prominent high aerosol loading centers are observed. Higher single scattering albedo（SSA） in summer is likely associated with the weak absorbing secondary aerosols. SSA is higher in North China during summer but higher in South China during winter. Aerosols induce negative forcing at the top of the atmosphere（TOA） and surface during both winter and summer, which may be responsible for the decrease in temperature and the increase in relative humidity.Values of ADRF at the surface are four times stronger than those at the TOA. Both AOD and ADRF present strong interannual variations; however, their amplitudes are larger in summer. Moreover, patterns and trends of ADRF do not always correspond well to those of AOD. Differences in the spatial distributions of ADRF between strong and weak monsoon years are captured effectively. Generally, the present results justify that to calculate grid-cell ADRF at a large scale using the SBDART model with observational aerosol optical properties and reanalysis data is an effective approach.

Anthropogenic Direct Radiative Forcing of Tropospheric Ozone and Aerosols in 1850 and 2000 Estimated with IPCC AR5 Emissions Inventories

This study estimates direct radiative forcing by tropospheric ozone and all aerosols between the years 1850 and 2000, using the new IPCC AR5 （the Intergovernmental Panel on Climate Change Fifth Assessment Report） emissions inventories and a fully coupled chemistry-aerosol general circulation model. As compared to the previous Global Emissions Inventory Activity （GEIA） data, that have been commonly used for forcing estimates since 1990, the IPCC AR5 emissions inventories report lower anthropogenic emissions of organic carbon and black carbon aerosols and higher sulfur and NOx emissions. The simulated global and annual mean burdens of sulfate, nitrate, black carbon （BC）, primary organic aerosol （POA）, secondary organic aerosol （SOA）, and ozone were 0.79, 0.35, 0.05, 0.49, 0.34, and 269 Tg, respectively, in the year 1850, and 1.90, 0.90, 0.11, 0.71, 0.32, and 377 Tg, respectively, in the year 2000. The estimated annual mean top of the atmosphere （TOA） direct radiative forcing of all anthropogenic aerosols based on the AR5 emissions inventories is -0.60 W m^-2 on a global mean basis from 1850 to 2000. However, this is -2.40 W m-2 when forcing values are averaged over eastern China （18-45°N and 95-125°E）. The value for tropospheric ozone is 0.17 W m^-1 on a global mean basis and 0.24 W m^-2 over eastern China. Forcing values indicate that the climatic effect of aerosols over eastern China is much more significant than the globally averaged effect.

Effect of Particle Shape on Dust Shortwave Direct Radiative Forcing Calculations Based on MODIS Observations for a Case Study

Assuming spheroidal and spherical particle shapes for mineral dust aerosols,the effect of particle shape on dust aerosol optical depth retrievals,and subsequently on instantaneous shortwave direct radiative forcing（SWDRF） at the top of the atmosphere（TOA）,is assessed based on Moderate Resolution Imaging Spectroradiometer（MODIS） data for a case study.Specifically,a simplified aerosol retrieval algorithm based on the principle of the Deep Blue aerosol retrieval method is employed to retrieve dust aerosol optical depths,and the Fu–Liou radiative transfer model is used to derive the instantaneous SWDRF of dust at the TOA for cloud-free conditions.Without considering the effect of particle shape on dust aerosol optical depth retrievals,the effect of particle shape on the scattering properties of dust aerosols（e.g.,extinction efficiency,single scattering albedo and asymmetry factor） is negligible,which can lead to a relative difference of at most 5% for the SWDRF at the TOA.However,the effect of particle shape on the SWDRF cannot be neglected provided that the effect of particle shape on dust aerosol optical depth retrievals is also taken into account for SWDRF calculations.The corresponding results in an instantaneous case study show that the relative differences of the SWDRF at the TOA between spheroids and spheres depend critically on the scattering angles at which dust aerosol optical depths are retrieved,and can be up to 40% for low dust-loading conditions.

Direct Radiative Forcing and Climatic Effects of Aerosols over East Asia by RegCM3

The authors used a high-resolution regional climate model （RegCM3） coupled with a chemistry/ aerosol module to simulate East Asian climate in 2006 and to test the climatic impacts of aerosols on regional- scale climate. The direct radiative forcing and climatic effects of aerosols （dust, sulfate, black carbon, and organic carbon） were discussed. The results indicated that aerosols generally produced negative radiative forcing at the top-of-the-atmosphere （TOA） over most areas of East Asia. The radiative forcing induced by aerosols exhibited significant seasonal and regional variations, with the strongest forcing occurring in summer. The aerosol feed- backs on surface air temperature and precipitation were clear. Surface cooling dominated features over the East Asian continental areas, which varied in the approximate range of-0.5 to -2℃ with the maximum up to -3℃ in summer over the deserts of West China. The aerosols induced complicated variations of precipitation. Except in summer, the rainfall generally varied in the range of-1 to 1 mm d^-1 over most areas of China.

Four-quadrant Force Control with Minimal Ripple for Linear Switched Reluctance Machines

Linear switch reluctance machine(LSRM)has been tried to act as an alternative generator for direct drive linear wave energy converter(WEC).Many researchers have proposed new topologies of LSRM to improve the power density,efficiency and reliability.However,the control methods for LSRM applied in direct drive WEC have been paid little attention,especially control methods considering the wave energy generator operating characteristics.In this paper,according to the generator control requirements of the direct drive WEC,force control algorithm for LSRM operating in four quadrants without a speed closed loop is put forward.The force ripple of LSRM is suppressed using force sharing function method.The four-quadrant control is easy to realize requiring only phase currents information.Simulation results validate the proposed method and indicate that LSRM is able to be used as the generator for direct drive WEC.

An Experimental Study of Irregular Wave Forces on Multiple Quasi-ellipse Caissons

An experimental investigation of irregular wave forces on quasi-ellipse caisson structures is presented. Irregular waves were generated based on the Jonswap spectrum with two significant wave heights, and the spectrum peak periods range from 1.19 s to 1.81 s. Incident wave directions relative to the centre line of the multiple caissons are from 0＆#176; to 22.5＆#176;. The spacing between caissons ranges from 2 to 3 times that of the width of the caisson. The effects of these parameters on the wave forces of both the perforated and non-perforated caissons were compared and analyzed. It was found that the perforated caisson can reduce wave forces, especially in the transverse direction. Furthermore, the relative interval and incident wave direction have significant effects on the wave forces in the case of multiple caissons.

Induction of Forces at Distance Performed by Piezoelectric Materials

We describe the phenomenon of generation of an external field of forces from piezoelectric materials subjected to the application of electric fields or mechanical stress. We show that piezoelectric materials are capable of producing nonlocal forces of induction in external objects and we conclude that the nature of the forces generated is not originated from traditional interactions. Further we specifically assert that the generation of forces by the piezoelectric materials is ruled by the hypothesis of preexisting condition of generalized quantum entanglement between the molecular structure of the material bulk and the surrounding environment. In addition, the widely spread coupling of the molecules with the environment can be manifested from the so-called direct effect or the converse effect in piezoelectric materials and this coupling is not intermediated by acoustic waves or electromagnetic fields. We show that the novel effect has a theoretical explanation consistent with the generalized quantum entanglement framework and the direction of the induced forces depends on either the direction of the mechanical force or the electric field applied in these materials.

Mechanism of drag reduction by spanwise oscillating Lorentz force in turbulent channel flow

Numerical simulations and experimental research are both carried out to investigate the controlled effect of spanwise oscillating Lorentz force on a turbulent channel flow. The variations of the streaks and the skin friction drag are obtained through the PIV system and the drag measurement system, respectively. The flow field in the near-wall region is shown through direct numerical simulations utilizing spectral method. The experimental results are consistent with the numerical simulation results qualitatively, and both the results indicate that the streaks are tilted into the spanwise direction and the drag reduction utilizing spanwise oscillating Lorentz forces can be realized. The numerical simulation results reveal more detail of the drag reduction mechanism which can be explained, since the spanwise vorticity generated from the interaction between the induced Stokes layer and intrinsic turbulent flow in the near-wall region can make the longitudinal vortices tilt and oscillate, and leads to turbulence suppression and drag reduction.

Effect of direction error on the miss distance of rolling missiles with x-rudder

Based on the analysis of periodic equivalent control force of rolling missiles with x-rudder, the guidance loop model with direction error is established and the relationship between direction error and miss distance is analyzed. Results show that the miss distance is zero or a constant or infinite, and it is always zero when the real parts of system matrix eigenvalues decided by direction error are both positive values in an ideal system, in which all the lags are neglected. However, the miss distance gradually increases with the increase of the direction error and its variation is small when direction error is not more than 5° in the system, in which seeker lag and missile body lag are considered.

Oblique and Multi-Directional Random Wave Loads on Vertical Breakwaters

Extensive 3-D model tests have been performed to study the effects of wave obliquity and multi-directionality on the wave loads acting on vertical breakwaters. The variation of horizontal and uplift forces acting on an unit length of a breakwater with wave direction, the longitudinal distribution of wave forces, as well as the longitudinal load reduction are analyzed. Some empirical formulae of the longitudinal distribution coefficient and the longitudinal load reduction factor are presented for practical use.

Numerical investigation of turbulent channel flow controlled by spatially oscillating spanwise Lorentz force

A formulation of the skin-friction drag related to the Reynolds shear stress in a turbulent channel flow is derived. A direct numerical simulation （DNS） of the turbulent control is performed by imposing the spatially oscillating spanwise Lorentz force. Under the action of the Lorentz force with several proper control parameters, only the periodi- cally well-organized streamwise vortices are finally observed in the near-wall region. The Reynolds shear stress decreases dramatically, especially in the near-wall area, resulting in a drag reduction.

Development of RAMS-CMAQ to Simulate Aerosol Optical Depth and Aerosol Direct Radiative Forcing and Its Application to East Asia

The air quality modeling system RAMS (Regional Atmospheric Modeling System)-CMAQ (Models-3 Community Multi-scale Air Quality) is developed to simulate the aerosol optical depth (AOD) and aerosol direct forcing (DF). The aerosol-specific extinction, single scattering albedo, and asymmetry factor are parameterized based on Mie theory taking into account the aerosol size distribution, composition, refractive index, and water uptake of solution particles. A two-stream solar radiative model considers all gaseous molecular absorption, Rayleigh scattering, and aerosols and clouds. RAMSCMAQ is applied to simulate all major aerosol concentrations (e.g., sulfate, nitrate, ammonium, organic carbon, black carbon, fine soil, and sea salt) and AOD and DF over East Asia in 2005. To evaluate its performance, the simulated AOD values were compared with ground-based in situ measurements. The comparison shows that RAMSCMAQ performed well in most of the model domain and generally captured the observed variations. High AOD values (0.2 1.0) mainly appear in the Sichuan Basin as well as in central and southeastern China. The geographic distribution of DF generally follows the AOD distribution patterns, and the DF at the top-of-the-atmosphere is less than 25 and 20 W m 2 in clear-sky and all-sky over the Sichuan Basin. Both AOD and DF exhibit seasonal variations with lower values in July and higher ones in January The DF could obviously be impacted by high cloud fractions.