Sustainable nitrogen fixation by bubble discharge plasma:Performance optimization and mechanism

Sustainable nitrogen fixation driven by renewable energy sources under mild conditions has been widely sought to replace the industrial Haber-Bosch process.The fixation of nitrogen in the form of NO_(x)^(-)and NH_4^(+)into aqueous solutions using electricity-driven gas-liquid discharge plasma is considered a promising prescription.In this paper,a scalable bubble discharge excited by nanosecond pulse power is employed for nitrogen fixation in the liquid phase.The nitrogen fixation performance and the mechanisms are analyzed by varying the power supply parameters,working gas flow rate and composition.The results show that an increase in voltage and frequency can result in an enhanced NO_(3)^(-)yield.Increases in the gas flow rate can result in inadequate activation of the working gas,which together with more inefficient mass transfer efficiencies can reduce the yield.The addition of O_(2) effectively elevates NO_(3)^(-)production while simultaneously inhibiting NH_4^(+) production.The addition of H_(2)O vapor increases the production of OH and H,thereby promoting the generation of reactive nitrogen and enhancing the yield of nitrogen fixation.However,the excessive addition of O_(2) and H_(2)O vapor results in negative effect on the yield of nitrogen fixation,due to the significant weakening of the discharge intensity.The optimal nitrogen fixation yield was up to 16.5 μmol/min,while the optimal energy consumption was approximately 21.3 MJ/mol in this study.Finally,the mechanism related to nitrogen fixation is discussed through the optical emission spectral(OES) information in conjunction with the simulation of energy loss paths in the plasma by BOLSIG+.The work advances knowledge of the effect of parameter variations on nitrogen fixation by gas-liquid discharge for higher yield and energy production.

Comparative analysis of single-crater parameters in ultrasonic-assisted and unassisted micro-EDM of Ti6Al4V using discharge plasma imaging

Ultrasonic-assisted micro-electro-discharge machining(EDM)has the potential to enhance processing responses such as material removal rate(MRR)and surface finish.To understand the reasons for this enhancement,the physical mechanisms responsible for the individual discharges and the craters that they form need to be explored.This work examines features of craters formed by single discharges at various parameter values in both conventional and ultrasonic-assistedEDM of Ti6Al4V.High-speed imaging of the plasma channel is performed,and data on the individual discharges are captured in real-time.A 2D axisymmetric model using finite element software is established to model crater formation.On the basis of simulation and experimental results,a comparative study is then carried out to examine the effects of ultrasonic vibrational assistance on crater geometry.For every set ofEDM parameters,the crater diameter and depth from a single discharge are found to be higher in ultrasonic-assistedEDM than in conventionalEDM.The improved crater geometry and the reduced bulge formation at the crater edges are attributed to the increased melt pool velocity and temperature predicted by the model.

Effect of antenna helicity on discharge characteristics of helicon plasma under a divergent magnetic field

The characteristics of the blue core phenomenon observed in a divergent magnetic field helicon plasma are investigated using two different helical antennas, namely right-handed and lefthanded helical antennas. The mode transition, discharge image, spatial profiles of plasma density and electron temperature are diagnosed using a Langmuir probe, a Nikon D90 camera,an intensified charge-coupled device camera and an optical emission spectrometer, respectively.The results demonstrated that the blue core phenomenon appeared in the upstream region of the discharge tube at a fixed magnetic field under both helical antennas. However, it is more likely to appear in a right-handed helical antenna, in which the plasma density and ionization rate of the helicon plasma are higher. The spatial profiles of the plasma density and electron temperature are also different in both axial and radial directions for these two kinds of helical antenna. The wavelength calculated based on the dispersion relation of the bounded whistler wave is consistent with the order of magnitude of plasma length. It is proved that the helicon plasma is part of the wave mode discharge mechanism.

Discharge plasma for prebiotic chemistry: Pathways to life’s building blocks

Discharge plasmas, recognized as unique platforms for investigating the origins of chemical life, have garnered extensive interest for their potential to simulate prebiotic conditions. This paper embarks on a comprehensive overview of recent advancements in the plasma-enabled synthesis of life’s building blocks, charting the complex environmental parameters believed to have surrounded life’s inception. This discussion elaborates on the fundamental mechanisms of discharge plasmas and their likely role in fostering conditions necessary for the origin of life on early Earth. We consider a variety of chemical reactions facilitated by plasma, specifically the synthesis of vital organic molecules - amino acids, nucleobases, sugars, and lipids. Further, we delve into the impact of plasmas on prebiotic chemical evolution. We expect this review to open new horizons for future investigations in plasma-related prebiotic chemistry that could offer valuable insights for unraveling the mysteries of life's origin.

Performance of pulsed plasma thruster at low discharge energy

As the size of satellites scales down, low-power and compact propulsion systems such as the pulsed plasma thruster(PPT) are needed for stabilizing these miniature satellites in orbit. Most PPT systems are operated at 2 J or more of discharge energy. In this work, the performance of a PPT with a side-fed, tongue-flared electrode configuration operated within a lower discharge energy range of 0.5-2.5 J has been investigated. Ablation and charring of the polytetrafluoroethylene propellant surface were analyzed through field-effect scanning electron microscopy imaging and energy-dispersive X-ray spectroscopy. When the discharge energy fell below 2 J, inconsistencies occurred in the specific impulse and the thrust efficiency due to the measurement of the low mass bit. At energy ≥2 J, the performance parameters are compared with other PPT systems of similar configuration and discussed in depth.

Reconfigurable(4, 6^(2)) and(4, 8^(2)) Archimedean plasma photonic crystals in dielectric barrier discharge

Archimedean photonic crystal has become a research area of great interest due to its various unique properties. Here, we experimentally demonstrate the realization of reconfigurable(4, 6^(2))and(4, 8^(2)) Archimedean plasma photonic crystals(APPCs) by use of dielectric barrier discharges in air. Dynamical control on both the macrostructures including the lattice symmetry and the crystal orientation, and the microstructures including the fine structures of scattering elements has been achieved. The formation mechanisms of APPCs are studied by time-resolved measurements together with numerical simulations. Large omnidirectional band gaps of APPCs have been obtained. The tunable topology of APPCs may offer new opportunities for fabricating multi-functional and highly-integrated microwave devices.

Comparison of the effect of different external electrodes on discharge plasma-assisted diffusion flame stabilization

To optimize the design of plasma injectors,the influence of different external electrodes on plasma-assisted flame stabilization was assessed by using a nonequilibrium plasma injector flame control setup.The electrical characteristics of the injector,flame structure parameters,flame intensity,discharge power,and cost-to-effectiveness ratio under different external electrodes(four mesh electrodes and one copper foil electrode)were analyzed using electrical and optical methods.The results show that reducing the mesh size of the external electrode leads to a decrease in breakdown voltage.Compared with a ceramic dielectric barrier-based injector,an injector with a quartz dielectric barrier produces a higher breakdown voltage under the same conditions.For the same actuation voltage,the discharge current increases as the mesh size of the external electrode decreases,and combustion is enhanced by the discharge plasma;therefore,it is better to adopt a smaller mesh hole size to realize good flame stabilization under a lower actuation voltage.However,under the studied working conditions,reducing the mesh hole size of the external electrode increases the cost-to-effectiveness ratio of plasma injector-based flame stabilization.Thus,considering the cost-to-effectiveness ratio and the weight of the injector,an external electrode with a larger mesh hole size should be chosen,which contradicts the above rule.

TREATMENT OF METALS, POLYMER FILMS, AND FABRICS WITHA ONE ATMOSPHERE UNIFORM GLOW DISCHARGE PLASMA(OAUGDP) FOR INCREASED SURFACE ENERGY AND DIRECTIONAL ETCHING

Direct exposure of samples to the active species of air generated by a One Atmosphere Uniform Glow Discharge Plasma (OAUGDP) has been used to etch and to increase the surface energy of metallic surfaces, photoresist, polymer films, and nonwoven fab- rics. The OAUGDP is a non-thermal plasma with the classical characteristics of a DC normal glow discharge that operates in air (and other gases) at atmospheric pres- sure. Neither a vacuum system nor batch processing is necessary. A wide range of applications to metals, photoresist, films, fabrics, and polymeric webs can be accom- modated by direct exposure of the workpiece to the plasma in parallel-plate reactors. This technolopy is simple, it produces effects that can be obtained in no other way at one atmosphere; it generates minimal pollutants or unwanted by-products; and it is suitable for individual sample or online treatment of metallic surfaces, wafers, films, and fabrics. Early exposures of solid materials to the OAUGDP required minutes to produce rela- tively small increases of surface energy. These durations appeared too long for com- mercial application to fast-moving webs. Recent improvements in OAUGDP gas com- position, power density, plasma quality, recireulating gas flow, and impedance match- ing of the power supply to the parallel plate plasma reactor have made it possible to raise the surface energy of a variety of polymeric webs (PP, PET PE etc.) to levels of 60 to 70 dynes/cm with one second of exposure. In air plasmas, the high surface ener- gies are not durable, and fall to 50 dynes/cm after periods of weeks to months. Here, we report the exposure of metallic surfaces, photoresist, polymeric films, and nonwo- ven fabrics made of PP and PET to an impedance matched parallel plate OAUGDP for durations ranging from one second to several tens of seconds. Data will be re- ported on the surface energy, wettability, wickability, and aging effect of polymeric films and fabrics as functions of time of exposure, and time after exposure; the rate and uniformity of photoresist etching; and the production of sub-micron structures by OAUGDP etching at one atmosphere.

Study of Humidity Effect on Benzene Decomposition by the Dielectric Barrier Discharge Nonthermal Plasma Reactor

The humidity effects on the benzene decomposition process were investigated by the dielectric barrier discharge（DBD） plasma reactor.The results showed that the water vapor played an important role in the benzene oxidation process.It was found that there was an optimum humidity value for the benzene removal efficiency,and at around 60% relative humidity（RH）,the optimum benzene removal efficiency was achieved.At a SIE of 378 J/L,the removal efficiency was 66% at 0% RH,while the removal efficiency reached 75.3% at 60% RH and dropped to 69% at 80% RH.Furthermore,the addition of water inhibited the formation of ozone and NO2 remarkably.Both of the concentrations of ozone and NO2 decreased with increasing of the RH at the same specific input energy.At a SIE of 256 J/L,the concentrations of ozone and NO2 were 5.4 mg/L and 1791 ppm under dry conditions,whereas they were only 3.4 mg/L and 1119 ppm at 63.5%RH,respectively.Finally,the outlet gas after benzene degradation was qualitatively analyzed by FT-IR and GC-MS to determine possible intermediate byproducts.The results suggested that the byproducts in decomposition of benzene primarily consisted of phenol and substitutions of phenol.Based on these byproducts a benzene degradation mechanism was proposed.

Toluene removal characteristics by a superimposed wire-plate dielectric barrier discharge plasma reactor

A superimposed wire-plate dielectric barrier discharge reactor was used to remove toluene in this study. The effects of oxygen content, gas flow rate, gas initial concentration and with/without catalyst on toluene decomposition were investigated. It was found that an optimal toluene removal was achieved when the oxygen content was about 5%. Under this condition, the highest toluene removal efficiency of 80.8% was achieved when the gas concentration was 80 mg/m^3. The toluene removal efficiency decreased with the increase of the gas flow rate and the initial concentration of toluene. In addition, the ozone concentration decreased with the increase of the initial concentration of toluene. It suggested that combining DBD （dielectric barrier discharge） with Co3O4/Al2O3/foam nickel catalyst in-situ could improve the toluene removal efficiency and suppress ozone formation. Products analysis showed that the main products were CO and CO2 when oxygen was more than 5%.

Review on reactive species in water treatment using electrical discharge plasma:formation, measurement, mechanisms and mass transfer

In the electrical discharge plasma process, various chemical and physical processes can participate in the removal of contaminants. In this paper, the chemical and physical processes that occur as a result of the electrical discharge plasma are reviewed, and their possible roles in the degradation of contaminants are discussed. Measurement methods for the quantification of important reactive species and their advantages and shortcomings are presented. Approaches on how to enhance the diffusion of the reactive species in solution are examined. In addition, the formation of typical reactive species in different electrical discharge plasma is compared.

Hybrid electric discharge plasma technologies for water decontamination:a short review

Electric discharge plasma(EDP)can efficiently degrade aqueous pollutants by its in situ gen erated strong oxidative species(OH,0,H2O2.O.etc)“nd other physiochemical effects(UV irradiation,shockwaves,local high temperature,etc),but a high energy consumptions limit the application of EDP in water treatment.Some adsorbents,catalysts,and oxida nts have been employed for en hanci ng the degradation of pollutants by discharge plasma.These hybrid plasma technologies offer improved water treatment performance compared to dischai'ge plasma alone.This paper reviews the water decontamination performance and mechanisms of these hybrid plasma technologies,and some suggestions on future water treatment technologies based on discharge plasma are also proposed.

NOx Reduction and Desorption Studies Under Electric Discharge Plasma Using a Simulated Gas Mixture:A Case Study on the Effect of Corona Electrodes

In this study, reduction and desorption of oxides of nitrogen （NOx） were conducted using an electrical discharge plasma technique. The study was carried out using a simulated gas mixture to explore the possibility of re-generation of used adsorbents by a nonthermal plasma desorption technique. Three different types of corona electrodes, namely, pipe, helical wire, and straight wire, were used for analyzing their effectiveness in NOx reduction/desorption. The pipe- type corona electrode exhibited a nitric oxide （NO） conversion of 50%, which is 1.5 times that of the straight-wire-type electrode at an energy density of 175 J/L. The helical-wire-type corona electrode exhibited a NOx desorption efficiency almost 4 times that of the pipe-type electrode, indicating the possibility that corona-generated species play a crucial role in desorption.

Oxidative Degradation of 4-chlorophenol in Aqueous Induced by Plasma with Submersed Glow Discharge Electrolysis

The oxidative degradation of 4-chlorophenol （4-CP） in aqueous solution induced by plasma with submersed glow discharge has been investigated. The concentration of 4-CP and the reaction intermediates were determined by high performance liquid chromatography （HPLC）. Various influencing factors such as the initial pH, the concentration of 4-CP and the catalytic action of Fe^2＋ were examined. The results indicate that 4-CP is eventually degraded into inorganic ion, dioxide carbon and water. The attack of hydroxyl radicals on the benzene rings of 4-CP in the initial stage of oxidative reactions is presumed to be a key step. They also suggest that the reaction is of a pseudo-first order kinetic reaction and the proposed method is an efficient way for the 4-CP degradation,

A zirconium modified Co/SiO_2 Fischer-Tropsch catalyst prepared by dielectric-barrier discharge plasma

Co/SiO2 and zirconium promoted Co/Zr/SiO2 catalysts were prepared using dielectric-barrier discharge （DBD） plasma instead of the conventional thermal calcination method. Fischer-Tropseh Synthesis （FTS） performances of the catalyst were evaluated in a fixed bed reactor. The results indicated that the catalyst treated by DBD plasma shows the higher FTS activity and yield of heavy hydrocarbons as compared with that treated by the conventional thermal calcination method. Increase in CO conversion was unnoticeable on the Co/SiO2 catalyst, but significant on the Co/Zr/SiO2 catalyst, both prepared by DBD plasma. On the other hand, heavy hydrocarbon selectivity and chain growth probability （a value） were enhanced on all the catalysts prepared by the DBD plasma. In order to study the effect of the DBD plasma treatment on the FTS performance, the catalysts were characterized by N2-physisorption, H2-temperature programed reduction （H2-TPR）, H2-temperature- programmed desorption （H2-TPD） and oxygen titration, transmission electron microscope （TEM） and X-ray diffraction （XRD）. It was proved that, compared with the traditional calcination method, DBD plasma not only could shorten the precursor decomposition time, but also could achieve better cobalt dispersion, smaller Co304 cluster size and more uniform cobalt distribution. However, cobalt reducibility was hindered to some extent in the Co/SiO2 catalyst prepared by DBD plasma, while the zirconium additive prevented significantly the decrease in cobalt reducibility and increased cobalt dispersion as well as the FTS performance.

Treatment of Invasive Marine Species on Board by Using Micro-gap Discharge Plasma

A pilot-scale experiment of 20t/h for the treatment of ship＇s ballast water is reported in this paper. When the concentration of the dissolved OH. was 0.68 mg/L during the experiment, the rate of destroying bacteria, mono-algae, protozoan reached 100% within 2.67 s. The effect of hydroxyl radicals on biochemical processes was also studied. The attenuation rate of photosynthesis pigment was 100%. And the main reason for the cells＇ death was the strong destruction of the monose, amylose, protein, DNA and RNA in the cells. As an advanced oxidation method, the procedure can destroy invasive marine species when a ship is in the process of discharging its ballast water.

Treatment of Dye Wastewater by Using a Hybrid Gas/Liquid Pulsed Discharge Plasma Reactor

A hybrid gas/liquid pulsed discharge plasma reactor using a porous ceramic tube is proposed for dye wastewater treatment. High voltage pulsed discharge plasma was generated in the gas phase and simultaneously the plasma channel was permeated through the tiny holes of the ceramic tube into the water phase accompanied by gas bubbles. The porous ceramic tube not only separated the gas phase and liquid phase but also offered an effective plasma spreading channel. The effects of the peak pulse voltage, additive gas varieties, gas bubbling rate, solution conductivity and TiO2 addition were investigated. The results showed that this reactor was effective for dye wastewater treatment. The decoloration efficiency of Acid Orange II was enhanced with an increase in the power supplied. Under the studied conditions, 97% of Acid Orange II in aqueous solution was effectively decolored with additive oxygen gas, which was 51% higher than that with argon gas, and the increasing 02 bubbling rate also benefited the decoloration of dye wastewater. Water conductivity had a small effect on the level of decoloration. Catalysis of TiO2 could be induced by the pulsed discharge plasma and addition of TiO2 aided the decoloration of Acid Orange II.

Preparation of N‐vacancy‐doped g‐C_3N_4 with outstanding photocatalytic H_2O_2 production ability by dielectric barrier discharge plasma treatment

Dielectric barrier discharge（DBD） plasma is considered to be a promising method to synthesize solid catalysts. In this work, DBD plasma was used to synthesize a nitrogen‐vacancy‐doped g‐C3N4 catalyst in situ for the first time. X‐ray diffraction, N2 adsorption, ultraviolet–visible spectroscopy, scanning electron microscopy, transmission electron microscopy, X‐ray photoelectron spectrosco‐py, electrochemical impedance spectroscopy, electron paramagnetic resonance, O2 tempera‐ture‐programmed desorption, and photoluminescence were used to characterize the obtained cat‐alysts. The photocatalytic H2O2 production ability of the as‐prepared catalyst was investigated. The results show that plasma treatment influences the morphology, structure, and optical properties of the as‐prepared catalyst. Nitrogen vacancies are active centers, which can adsorb reactant oxygen molecules, trap photoelectrons, and promote the transfer of photoelectrons from the catalyst to the adsorbed oxygen molecules for the subsequent reduction reaction. This work provides a new strat‐egy for synthesizing g‐C3N4‐based catalysts.

Conversion from Dimethyl Ether to Dimethoxymethane and Dimethoxyethane Using Dielectric-Barrier Discharge Plasma

Experimental investigation was conducted to convert dimethyl ether (DME) in the presence of steam using dielectric barrier discharge (DBD) at atmospheric pressure and 373 K. The flow rate of DME was 20 ml/min. The introduction of steam resulted in an increase in the DME conversion and the selectivity of oxygenates. Plasma steam-enhanced dimethyl ether (DME) conversion led to a direct synthesis of DMMT and DMET, with a high selectivity of 5.78% and 17.99%, respectively. The addition of steam promoted the formation of 'plasma aerosol' that was favored for the formation of liquid oxygenates. The reaction pathway of plasma DME conversion was proposed.

UAV flight test of plasma slats and ailerons with microsecond dielectric barrier discharge

Plasma flow control（PFC） is a promising active flow control method with its unique advantages including the absence of moving components, fast response, easy implementation, and stable operation. The effectiveness of plasma flow control by microsecond dielectric barrier discharge（μs-DBD）, and by nanosecond dielectric barrier discharge（NS-DBD） are compared through the wind tunnel tests, showing a similar performance between μs-DBD and NS-DBD. Furthermore, theμs-DBD is implemented on an unmanned aerial vehicle（UAV）, which is a scaled model of a newly developed amphibious plane. The wingspan of the model is 2.87 m, and the airspeed is no less than 30 m/s. The flight data, static pressure data,and Tufts images are recorded and analyzed in detail. Results of the flight test show that the μs-DBD works well on board without affecting the normal operation of the UAV model. When the actuators are turned on, the stall angle and maximum lift coefficient can be improved by 1.3° and 10.4%, and the static pressure at the leading edge of the wing can be reduced effectively in a proper range of angle of attack, which shows the ability of μs-DBD to act as plasma slats. The rolling moment produced by left-side μs-DBD actuation is greater than that produced by the maximum deflection of ailerons,which indicates the potential of μs-DBD to act as plasma ailerons. The results verify the feasibility and efficacy of μs-DBD plasma flow control in a real flight and lay the foundation for the full-sized airplane application.