Channel estimation in integrated radar and communication systems with power amplifier distortion

To reduce the negative impact of the power amplifier(PA)nonlinear distortion caused by the orthogonal frequency division multiplexing(OFDM)waveform with high peak-to-average power ratio(PAPR)in integrated radar and communication(RadCom)systems is studied,the channel estimation in passive sensing scenarios.Adaptive channel estimation methods are proposed based on different pilot patterns,considering nonlinear distortion and channel sparsity.The proposed methods achieve sparse channel results by manipulating the least squares(LS)frequency-domain channel estimation results to preserve the most significant taps.The decision-aided method is used to optimize the sparse channel results to reduce the effect of nonlinear distortion.Numerical results show that the channel estimation performance of the proposed methods is better than that of the conventional methods under different pilot patterns.In addition,the bit error rate performance in communication and passive radar detection performance show that the proposed methods have good comprehensive performance.

A new method for measuring the pulse-front distortion of arbitrary shapes in high-power ultrashort laser systems

We present a new method that can be used to calculate pulse-front distortion by measuring the spectral interference of two point-diffraction fields in their overlapped district. We demonstrate, for the first time, the measurement of the pulse-front distortion of the pulse from a complex multi-pass amplification system, which exists in almost all high-power laser systems, and obtain the irregular pulse-front distribution. The method presented does not need any reference light or assumption about the pulse-front distribution, and has an accuracy of several femtoseconds.

Design of Dispersion Compensation and Nonlinear Distortion Self-compensationin Co -network Transmission Systems

Dispersion and nonlinear distortion have an effect on transmission performanc es of optic al fiber transimission systems. The schemes of dispersion compensation and nonli near distortion self-compens ation in telecom-CATV co-network transmission systems are reported, followed by investigation on (1) the impact of dispersion compensation fiber (DCF) on fi ber nonlinear effects with a cascade of erbium-doped fiber amplifiers (EDFAs) an d different dispersion compensation schemes, (2) the impact of the complex on th e total nonlinear distortion induced by EDFA gain tilt and the light source. As a result , dispersion compensation optimal scheme and EDFA negative gain tilt are suggest ed as a solution to dispersion compensation and the nonlinear distortion self-c ompensation.

Engineering Thermoelectric Performance of α-GeTe by Ferroelectric Distortion

The rhombohedralα-GeTe can be approximated as a slightly distorted rock-salt structure along its[111]direction and possesses superb thermoelectric performance.However,the role of such a ferroelectric-like structural distortion on its transport properties remains unclear.Herein,we performed a systematic study on the crystal structure and electronic band structure evolutions of Ge_(1-x)Sn_(x)Te alloys where the degree of ferroelectric distortion is continuously tuned.It is revealed that the band gap is maximized while multiple valence bands are converged at x=0.6,where the ferroelectric distortion is the least but still works.Once undistorted,the band gap is considerably reduced,and the valence bands are largely separated again.Moreover,near the ferro-to-paraelectric phase transition Curie temperature,the lattice thermal conductivity reaches its minima because of significant lattice softening enabled by ferroelectric instability.We predict a peak ZT value of 2.6 at 673 K inα-GeTe by use of proper dopants which are powerful in suppressing the excess hole concentrations but meanwhile exert little influence on the ferroelectric distortion.

Uzbekistan's coordinate system transformation from CS42 to WGS84 using distortion grid model

Currently,a non-geocentric geodetic coordinate system introduced in 1942(CS42),based on the Krasovsky ellipsoid and the Baltic system of normal heights introduced in 1977,is used for geodetic works in the Republic of Uzbekistan.The development of the GNSS network proposes a task of transition to a new geocentric system based on the World Geodetic System 1984(WGS84)ellipsoid.Many software products adopt 3-or 7-parameter conversions,which can cause errors up to several meters and are not suitable for many applications.In this case,local transformations using a grid of differences between observation points with known coordinates in both datums would give the best accuracy.In this paper,we discuss various interpolation methods(Kriging,Minimum Curvature,Inverse Distance to a Power and Radial Basis Function)to solve the distortion modeling between CS42 and WGS84 systems for national datum improvement.The results show that the distortion models share a common tendency for all interpolation methods:the maximum horizontal displacements are concentrated along the West Tien Shan lineament,which is the boundary of the relief lowering.The discrepancies between the grid-based(calculated)and GPS-measured coordinates are evaluated.Statistical and spatial analysis has confirmed that for the co-ordinate transformation from CS42 to WGS84 and vice versa,grid-based transformation with Radial Basis Function interpolation has a high accuracy transformation.Analysis of the available data across the eastern part of the country shows that some positional distortions existed between the CS42 and WGS84 datums.For the best RBF method,the magnitude of these distortions is about 0.019-0.755 m with a standard deviation of 0.015 m.

Performance Assessment of a Real PV System Connected to a Low-Voltage Grid

The generation of photovoltaic(PV)solar energy is increasing continuously because it is renewable,unlimited,and clean energy.In the past,generation systems depended on non-renewable sources such as oil,coal,and gas.Therefore,this paper assesses the performance of a 51 kW PV solar power plant connected to a low-voltage grid to feed an administrative building in the 6th of October City,Egypt.The performance analysis of the considered grid-connected PV system is carried out using power system simulator for Engineering(PSS/E)software.Where the PSS/E program,monitors and uses the power analyzer that displays the parameters and measures some parameters such as current,voltage,total power,power factor,frequency,and current and voltage harmonics,the used inverter from the type of grid inverter for the considered system.The results conclude that when the maximum solar radiation is reached,the maximum current can be obtained from the solar panels,thus obtaining the maximum power and power factor.Decreasing total voltage harmonic distortion,a current harmonic distortion within permissible limits using active harmonic distortion because this type is fast in processing up to 300 microseconds.The connection between solar stations and the national grid makes the system more efficient.

Low Distortion 1.31μm AlGaInAs/InP MQW DFB Laser Module for CATV Systems

A high power and low distortion 1.31 μm AlGaInAs/InP multiquantum well distributed feedback laser diode (MQW DFB LD) with RWG structure has been developed by MOCVD technique. The fiber output power of butterfly packaged module with optic isolator P f is more than 10 mW, threshold current is in the range of (13～20) mA, slope efficiency, E s>0.30 W/A and side mode suppression ratio, R S,M,S >35 dB. The composite second order, O C,S <-61 dBc and composite triple beat, B C,T <-65 dBc are obtained by test frequencies of (45～550) MHz with 60 PAL channels. In the test conditions the carrier to noise ratio, R C,N >51 dB.

Projecting Distortion Calibration and Evaluation of Coding Fringes in Structured Light System

Coded structured light is an accurate, fast 3D measurement approach with high sampling density, of which the encoded fringes are distorted when projected to curved surface. Focused on the demand of encoding, decoding, multiview registration and system calibration, we expect to obtain undistorted fringes from camera image. Therefore, in this paper, we analyze the accuracy and sampling density of projecting distortion calibration approach based on control point and fitting surface. Moreover, combining the characteristic of coded structured light system, we design encoded fringe projecting distortion calibration scheme based on simplified encoded structured light model. Primarily, we neglect the minor parameters that affect the calibration in structured light model to reduce complexity. Then, we build the correspondence between camera image points and projector image points and achieve the calibration. Finally, we design evaluation scheme of projecting distortion calibration with parallelism and equal interval, and verify the effectiveness and accuracy of the approach through visual effect and experimental data.

RESEARCH ON IMAGE DISTORTION AND CORRECTIVE METHODS OF PHASED ARRAY B- MODE ULTRASOUND DIAGNOSIS SYSTEM

Image geometry distortion is an important technical standard in B-mode ultra-sound diagnosis system.This paper investigates the cause of image distortion inphased array B-mode ultrasound diagnosis system.The first distortion cause is thedelay error of compound wave bind.Phased array ultrasound tranducer is composedof many rectangle units.With controlling inspiring plus time,ultrasound

Cross-section distortion and springback characteristics of double-cavity aluminum profile in force controlled stretch-bending

3D elastic-plastic FE model for simulating the force controlled stretch-bending process of double-cavity aluminum profile was established using hybrid explicit−implicit solvent method.Considering the computational accuracy and efficiency,the optimal choices of numerical parameters and algorithms in FE modelling were determined.The formation mechanisms of cross-section distortion and springback were revealed.The effects of pre-stretching,post-stretching,friction,and the addition of internal fillers on forming quality were investigated.The results show that the stress state of profile in stretch-bending is uniaxial with only a circumferential stress.The stress distribution along the length direction of profile is non-uniform and the maximum tensile stress is located at a certain distance away from the center of profile.As aluminum profile is gradually attached to bending die,the distribution characteristic of cross-section distortion along the length direction of profile changes from V-shape to W-shape.After unloading the forming tools,cross-section distortion decreases obviously due to the stress relaxation,with a maximum distortion difference of 13%before and after unloading.As pre-stretching and post-stretching forces increase,cross-section distortion increases gradually,while springback first decreases and then remains unchanged.With increasing friction between bending die and profile,cross-section distortion slightly decreases,while springback increases.Cross-section distortion decreases by 83%with adding PVC fillers into the cavities of profile,while springback increases by 192.2%.

Bulging Distortion of Austenitic Stainless Steel Sheet on the Partially Penetrated Side of Non-Penetration Lap Laser Welding Joint

Non-penetration laser welding of lap joints in austenitic stainless steel sheets is commonly preferred in fields where the surface quality is of utmost importance.However,the application of non-penetration welded austenitic stainless steel parts is limited owing to the micro bulging distortion that occurs on the back surface of the partial penetration side.In this paper,non-penetration lap laser welding experiments,were conducted on galvanized and SUS304 austenitic stainless steel plates using a fiber laser,to investigate the mechanism of bulging distortion.A comparative experiment of DC01 galvanized steel-Q235 carbon steel lap laser welding was carried out,and the deflection and distortion profile of partially penetrated side of the sheets were measured using a noncontact laser interferometer.In addition,the cold-rolled SUS304 was subjected to heat holding at different temperatures and water quenching after bending to characterize its microstructure under tensile and compressive stress.The results show that,during the heating stage of the thermal cycle of laser lap welding,the partial penetration side of the SUS304 steel sheet generates compressive stress,which extrudes the material in the heat-affected zone to the outside of the back of the SUS304 steel sheet,thereby forming a bulge.The findings of these experiments can be of great value for controlling the distortion of the partial penetrated side of austenitic stainless steel sheet during laser non-penetration lap welding.

Local tetragonal distortion of Pt alloy catalysts for enhanced oxygen reduction reaction efficiency

Platinum-based alloy nanoparticles are the most attractive catalysts for the oxygen reduction reaction at present,but an in-depth understanding of the relationship between their short-range structural information and catalytic performance is still lacking.Herein,we present a synthetic strategy that uses transition-metal oxide-assisted thermal diffusion.PtCo/C catalysts with localized tetragonal distortion were obtained by controlling the thermal diffusion process of transition-metal elements.This localized structural distortion induced a significant strain effect on the nanoparticle surface,which further shortened the length of the Pt-Pt bond,improved the electronic state of the Pt surface,and enhanced the performance of the catalyst.PtCo/C catalysts with special short-range structures achieved excellent mass activity(2.27 Amg_(Pt)^(-1))and specific activity(3.34 A cm^(-2)).In addition,the localized tetragonal distortion-induced surface compression of the Pt skin improved the stability of the catalyst.The mass activity decreased by only 13% after 30,000 cycles.Enhanced catalyst activity and excellent durability have also been demonstrated in the proton exchange membrane fuel cell configuration.This study provides valuable insights into the development of advanced Pt-based nanocatalysts and paves the way for reducing noble-metal loading and increasing the catalytic activity and catalyst stability.

Linear magnetoresistance and structural distortion in layered SrCu_(4-x)P_(2) single crystals

We report a systematic study on layered metal SrCu_(4-x)P_(2) single crystals via transport, magnetization, thermodynamic measurements and structural characterization. We find that the crystals show large linear magnetoresistance without any sign of saturation with a magnetic field up to 30T. We also observe a phase transition with significant anomalies in resistivity and heat capacity at T_(p)~140 K. Thermal expansion measurement reveals a subtle lattice parameter variation near Tp, i.e.,?L_(c)/L_(c)~0.062%. The structural characterization confines that there is no structure transition below and above T_(p). All these results suggest that the nonmagnetic transition of SrCu_(4-x)P_(2) could be associated with structural distortion.

Computational Quantification of Map Projection Distortion by Fractal Dimension of Coastlines

Maps, essential tools for portraying the Earth’s surface, inherently introduce distortions to geographical features. While various quantification methods exist for assessing these distortions, they often fall short when evaluating actual geographic features. In our study, we took a novel approach by analyzing map projection distortion from a geometric perspective. We computed the fractal dimensions of different stretches of coastline before and after projection using the divide-and-conquer algorithm and image processing. Our findings revealed that map projections, even when preserving basic shapes, inevitably stretch and compress coastlines in diverse directions. This analysis method provides a more realistic and practical way to measure map-induced distortions, with significant implications for cartography, geographic information systems (GIS), and geomorphology. By bridging the gap between theoretical analysis and real-world features, this method greatly enhances accuracy and practicality when evaluating map projections.

Application of the Delaunay triangulation interpolation in distortion XRII image

To alleviate the distortion of XRII X-ray image intensifier images in the C-arm CT computer tomography imaging system an algorithm based on the Delaunay triangulation interpolation is proposed.First the causes of the phenomenon the classical correction algorithms and the Delaunay triangulation interpolation are analyzed.Then the algorithm procedure is explained using flow charts and illustrations. Finally experiments are described to demonstrate its effectiveness and feasibility. Experimental results demonstrate that the Delaunay triangulation interpolation can have the following effects.In the case of the same center the root mean square distances RMSD and standard deviation STD between the corrected image with Delaunay triangulation interpolation and the ideal image are 5.760 4 ×10 -14 and 5.354 2 ×10 -14 respectively.They increase to 1.790 3 2.388 8 2.338 8 and 1.262 0 1.268 1 1.202 6 after applying the quartic polynomial model L1 and model L2 to the distorted images respectively.The RMSDs and STDs between the corrected image with the Delaunay triangulation interpolation and the ideal image are 2.489 × 10 -13 and 2.449 8 ×10 -13 when their centers do not coincide. When the quartic polynomial model L1 and model L2 are applied to the distorted images they are 1.770 3 2.388 8 2.338 8 and 1.269 9 1.268 1 1.202 6 respectively.

A Novel Segregation Distortion in Intraspecific Population of Asian Cotton(Gossypium arboretum L.)Detected by Molecular Markers

The segregation ratio of markers in an F2 population derived from Rudongjijiaoyaguo （Rdjjyg） and Zhongmian971 （Zm971） was studied using 3 morphological markers, 20 SSR markers, and ll SRAP markers. Totally, 24 markers （77.42%） showed a distorted segregation and all of them skewed toward the female genotype, which was peculiar in recent cotton research. All the three types of SSR markers and SRAP marker showed distorted segregation, but the morphological markers （Purple stem, Okra leaf, and Red spot color） were normally segregated. This indicated that such a novel segregation distortion phenomenon resulted from interior genetic factors, The allele frequency and the distribution of different genotype frequencies in the F2 population were analyzed in codominant markers, to find out factors attributed to distorted segregation. Most of them implied distorted allele frequency, but it was normal genotype frequency, which showed that these markers were influenced at the gamete level.

水稻内稃扭曲突变体palea distortion 1(pd1)的鉴定与基因定位

在对籼稻缙恢10进行EMS(ethyl methane sulfonate)处理后的群体中,发现一个花器官突变体,主要表现为内稃扭曲并呈现外稃化特征,浆片数目增加且呈现稃状特征,雄蕊数目减少至1～4个,部分雄蕊的花丝呈现浆片化特征,暂将其命名为水稻颖壳扭曲突变体palea distortion 1(pd1)。遗传分析表明该突变性状受一个隐形单基因控制。利用群体分离分析法(bulked segregation analysis,BSA),将PD1基因定位在第2染色体的RM13693和RM13936之间,遗传距离分别为3.25cM和3.90cM。该研究结果为PD1基因的图位克隆奠定了基础。

Cascade Kalman filter for gravity anomaly distortion correction based on second order potential model

Using a gravity anomaly covariance function based on the second-order Ganssian Markov gravity anomaly potential model, the state equation of a gravity anomaly signal is obtained in marine gravimetry. Combined with the system state equation and the measurement equation, a new method of the cascade Kalman filter is proposed and applied to the correction of gravity anomaly distortion. In the signal processing procedure, an inverse Kalman filter is used to restore the gravity anomaly signal and high frequency noises first. Then an adaptive Kalman filter, which uses the gravity anomaly state equation as the system equation, is set to estimate the actual gravity anomaly data. Emulations and experiments indicate that both the cascade Kalman filter method and the single inverse Kalman filter method are effective in alleviating the distortion of the gravity anomaly signal, but the performance of the cascade Kalman filter method is better than that of the single inverse Kalman filter method.

The anti-correlation method for removing harmonic distortion in vibroseis slip-sweep data

The slip-sweep technique is one of the high-efficiency, high-fidelity, and environmental vibroseis seismic prospecting techniques which consists of a vibrator group sweeping without waiting for the previous group＇s sweep to terminate. The cycle time can be reduced drastically and hence the production efficiency can be increased significantly but harmonic distortion of one sweep will leak into the record of the other sweep. In this paper, we propose an anti-correlation method for removing harmonic distortion in vibroseis data. This method is based on decomposition of the ground force signal into fundamental and harmonic components. Then the corresponding anti-correlation operator can be computed to estimate the energy of each harmonic after correlating the vibroseis data with the corresponding harmonic component. Finally, the vibroseis harmonic noise to be removed can be obtained by subtracting the extracted harmonic noise from the traces of the previous group＇s sweep. The advantage of the proposed method is that it can process both uncorrelated and correlated vibroseis seismic data. Moreover, the algorithm is simple, stable, and computationally fast. Especially, the significant contribution of this method is a considerable reduction in the harmonic without any alteration of the desired signals. The method was tested on both synthetic and field data sets to validate the good harmonic noise suppression results.

Application of stiffness matrix of a beam element considering section distortion effect

According to the stationary principle of potential energy and the generalized coordinate method, a stiffness matrix of a beam element considering distortion effects is derived. Using the stiffness matrix of the beam element, a finite element program for computing thin-walled box steel beams is developed. And the program can take the section distortion and warping effects into account. The influences of diaphragm spacing on the mechanical behavior of thin-walled box beams are analyzed by the program. The numerical analysis shows that setting diaphragms have the greatest influence on the distortion normal stress, while there is very little influence on the bending normal stress. Only when the distance of adjacent diaphragms decreases to a certain value, will the distortion normal stress in the thin-walled box beam obviously reduce under the distortion load. Finally, a distortion-warping coefficient γ is introduced for simplifying the calculation of the longitudinal normal stress of thin-walled box beams. When the ratio of diaphragms adjacent space L to the maximum section dimension H is less than 2, the distortion-warping coefficient γ tends to one, which means that the distortion normal stress of the thin-walled box beam tends to zero, and the effect of the section distortion can be ignored.