Network Integration of Distributed Optical Fiber Temperature Sensor

The integration of distributed optical fiber temperature sensor with supervisory control and data acquisition （SCADA） system is proposed and implemented. In the implementation of the integration, both the compatibility with traditional system and the characteristics of distributed optical fiber temperature sensor is considered before Modbus TCP/IP protocol is chosen. The protocol is implemented with open source component Indy. The Modbus TCP/IP protocol used in the system is proved to be fast and robust.

Distributed fiber optic sensors for tunnel monitoring:A state-of-the-art review

Distributed fiber optic sensors(DFOSs)possess the capability to measure strain and temperature variations over long distances,demonstrating outstanding potential for monitoring underground infrastructure.This study presents a state-of-the-art review of the DFOS applications for monitoring and assessing the deformation behavior of typical tunnel infrastructure,including bored tunnels,conventional tunnels,as well as immersed and cut-and-cover tunnels.DFOS systems based on Brillouin and Rayleigh scattering principles are both considered.When implementing DFOS monitoring,the fiber optic cable can be primarily installed along transverse and longitudinal directions to(1)measure distributed strains by continuously adhering the fiber to the structure’s surface or embedding it in the lining,or(2)measure point displacements by spot-anchoring it on the lining surface.There are four critical aspects of DFOS monitoring,including proper selection of the sensing fiber,selection of the measuring principle for the specific application,design of an effective sensor layout,and establishment of robust field sensor instrumentation.These four issues are comprehensively discussed,and practical suggestions are provided for the implementation of DFOS in tunnel infrastructure monitoring.

Flexible Optical Waveguide Bent Loss Attenuation Effects Analysis and Modeling Application to an Intrinsic Optical Fiber Temperature Sensor

The temperature dependence of the bending loss light energy in multimode optical fibers is reported and analyzed. The work described in this paper aims to extend an initial previous analysis concerning planar optical waveguides, light energy loss, to circular optical waveguides. The paper also presents à novel intrinsic fiber optic sensing device base on this study allowing to measure temperatures parameters. The simulation results are validated theoretically in the case of silica/silicone optical fiber. A comparison is done between results obtained with an optical fiber and the results obtained from the previous curved optical planar waveguide study. It is showed that the bending losses and the temperature measurement range depend on the curvature radius of an optical fiber or waveguide and the kind of the optical waveguide on which the sensing process is implemented.

Distributed optical fiber acoustic sensor for in situ monitoring of marine natural gas hydrates production for the first time in the Shenhu Area,China

The distributed acoustic sensor(DAS)uses a single optical cable as the sensing unit,which can capture the acoustic and vibration signals along the optical cable in real-time.So it is suitable for monitoring downhole production activities in the process of oil and gas development.The authors applied the DAS system in a gas production well in the South China Sea for in situ monitoring of the whole wellbore for the first time and obtained the distributed acoustic signals along the whole wellbore.These signals can clearly distinguish the vertical section,curve section,and horizontal production section.The collected acoustic signal with the frequency of approximately 50 Hz caused by the electric submersible pump exhibit a signal-to-noise ratio higher than 27 dB.By analyzing the acoustic signals in the production section,it can be located the layers with high gas production rates.Once an accurate physical model is built in the future,the gas production profile will be obtained.In addition,the DAS system can track the trajectory of downhole tools in the wellbore to guide the operation.Through the velocity analysis of the typical signals,the type of fluids in the wellbore can be distinguished.The successful application of the system provides a promising whole wellbore acoustic monitoring tool for the production of marine gas hydrate,with a good application prospect.

Temperature sensor based on a single-mode tapered optical fiber

A temperature sensor is demonstrated and fabricated by coating the single-mode tapered optical fiber with temperature-sensitive silicone rubber. It works on the change of the evanescent fields in the tapered optical fiber. Small changes in the refractive index of coating film greatly influence the power of evanescent fields, which modulate the transmission optical power in the waist region. The range of temperature measured is from -20℃ to 70 ℃. The results show that the temperature sensor has high temperature sensitivity （0.012 mW/℃） and good repeatability.

Highly sensitive optical fiber temperature sensor based on resonance in sidewall of liquid-filled silica capillary tube

A highly sensitive optical fiber temperature sensor based on a section of liquid-filled silica capillary tube(SCT)between single mode fibers is proposed. Two micro-holes are drilled on two sides of SCT directly by using femtosecond laser micromachining, and liquid polymer is filled into the SCT through the micro-holes without any air bubbles and then sealed by using ultra-violet(UV) cure adhesive. The sidewall of the SCT forms a Fabry–Perot resonator, and loss peaks are achieved in the transmission spectrum of the SCT at the resonant wavelength. The resonance condition can be influenced by the refractive index variation of the liquid polymer filled in SCT, which is sensitive to temperature due to its high thermooptical coefficient(-2.98 × 10^-4℃^-1). The experimental result shows that the temperature sensitivity of the proposed fiber structure reaches 5.09 nm/℃ with a perfect linearity of 99.8%. In addition, it exhibits good repeatability and reliability in temperature sensing application.

A Nonlinear Mirror Structure to Improve the Performance of the Distributed Fiber Temperature Sensor Based on Raman Backscattering

A novel nonlinear mirror structure which can increase the optical signal-to-noise ratio of a distributed fiber Raman temperature sensor is proposed, and 6 dB improvement of the optical signal-to-noise ratio is obtained. With the assistance of the nonlinear mirror, we demonstrate that the spatial resolution of the sensor is improved from 3 m to 1 m, and the temperature accuracy is improved from ±0.6℃ to ±0.2℃. The theoretical analysis and the experimental data are in good agreement.

Application of the Spectrum Peak Positioning Technology Based on BP Neural Network in Demodulation of Cavity Length of EFPI Fiber Optical Sensor

An Extrinsic Fabry-Perot Interferometric (EFPI) fiber optical sensor system is an online testing system for the gas density. The system achieves the measurement of gas density information mainly by demodulating the cavity length of EF- PI fiber optical sensor. There are many ways to achieve the demodulation of the cavity length. For shortcomings of the big intensity demodulation error and complex structure of phase demodulation, this paper proposes that BP neural net-work is used to locate the special peak points in normalized interference spectrum and combining the advantages of the unimodal and bimodal measurement achieves the demodulation of the cavity length. Through online simulation and actual measurement, the results show that the peak positioning technology based on BP neural network can not only achieve high-precision demodulation of the cavity length, but also achieve an absolute measurement of cavity length in large dynamic range.

Novel Fiber Optic Temperature Sensor with Full Compensation Based on Optical Absorption

A novel system configuration of fiber optic sensor based on optical abso rption is proposed. Several compensation measures are discussed. A simulated exp eriment is designed and the output curve of system is given. The experiment al result shows that these compensation measures are effective on dynamic distu rbances which are caused by background light and optical fiber bend. In addition , the drifts in the light source intensity, fiber losses, and photodetector effi ciency are also compensated.

DISTRIBUTED MICROBEND FIBER-OPTIC STRAIN SENSOR

The distributed strain sensor has significant application in real time measurement of strain status for large and important engineering structures such as aircraft, bridge and dam. In this paper, a quasi distributed optical fiber strain sensor system is set up using optical time domain reflect technique. The local strain sensors based on a novel microbend configuration are designed and applied to measure local strains along the optical fiber. As the result of the experimental research, the microbend sensors show high sensitivity, good linearity and repeatability in certain operation range.

Practical Pattern Recognition System for Distributed Optical Fiber Intrusion Monitoring Based on Ф-COTDR

At present, the demand for perimeter security system is in-creasing greatly, especially for such system based on distribut-ed optical fiber sensing. This paper proposes a perimeter se-curity monitoring system based on phase-sensitive coherentoptical time domain reflectometry(Ф-COTDR) with the practi-cal pattern recognition function. We use fast Fourier trans-form(FFT) to exact features from intrusion events and a multi-class classification algorithm derived from support vector ma-chine(SVM) to work as a pattern recognition technique. Fivedifferent types of events are classified by using a classifica-tion algorithm based on SVM through a three-dimensional fea-ture vector. Moreover, the identification results of the patternrecognition system show that an identification accurate rate of92.62% on average can be achieved.

Combined optical fiber interferometric sensors for the detection of acoustic emission

A type of combined optical fiber interferometric acoustic emission sensor is proposed. The sensor can be independent on the laser source and make light interference by matching the lengths of two arms,so it can be used to monitor the health of large structure. Theoretical analyses indicate that the system can be equivalent to the Michelson interferometer with two optical fiber loop reflectors,and its sensitivity has been remarkably increased because of the decrease of the losses of light energy. PZT is powered by DC regulator to control the operating point of the system,so the system can accurately detect feeble vibration which is generated by ultrasonic waves propagating on the surface of solid. The amplitude and the frequency of feeble vibration signal are obtained by detecting the output light intensity of interferometer and using Fourier transform technique. The results indicate that the system can be used to detect the acoustic emission signals by the frequency characteristics.

Loading Localization by Small-Diameter Optical Fiber Sensors

Structural health monitoring(SHM)in service has attracted increasing attention for years.Load localization on a structure is studied hereby.Two algorithms,i.e.,support vector machine(SVM)method and back propagation neural network(BPNN)algorithm,are proposed to identify the loading positions individually.The feasibility of the suggested methods is evaluated through an experimental program on a carbon fiber reinforced plastic laminate.The experimental tests involve in application of four optical fiber-based sensors for strain measurement at discrete points.The sensors are specially designed fiber Bragg grating(FBG)in small diameter.The small-diameter FBG sensors are arrayed in 2-D on the laminate surface.The testing results indicate that the loading position could be detected by the proposed method.Using SVM method,the 2-D FBG sensors can approximate the loading location with maximum error less than 14 mm.However,the maximum localization error could be limited to about 1 mm by applying the BPNN algorithm.It is mainly because the convergence conditions(mean square error)can be set in advance,while SVM cannot.

Fabry-Perot Temperature Sensor for Quasi-Distributed Measurement Utilizing OTDR

A quasi-distributed Fabry-Perot fiber optic temperature sensor array using optical time domain reflectometry （OTDR） technique is presented. The F-P sensor is made by two face to face single-mode optical fibers and their surfaces have been polished. Due to the low reflectivity of the fiber surfaces, the sensor is described as low Fresnel Fabry-Perot interferometer （FPI）. The working principle is analyzed using twobeam optical interference approximation. To measure the temperature, a certain temperature sensitive material is filled in the cavity. The slight changes of the reflective intensity which is induced by the refractive index of the material was caught by OTDR. The length of the cavity is obtained by monitoring the interference spectrum which is used for the setting of the sensor static characteristics within the quasi-linear range. Based on our design, a three point sensor array are fabricated and characterized. The experimental results show that with the temperature increasing from -30℃ to 80℃, the reflectivity increase in a good linear manner. The sensitivity was approximate 0.074 dB℃. For the low transmission loss, more sensors can be integrated.

All-Fiber Optic Temperature Sensor

This paper presents a new class of all fiber optic temperature sensor, of which the heat expansion thin film is coated on the etched fiber. The sensitivity of the sensor is increased and the shape size is decreased. This sensor possesses the linear temperature response and the good repeatability. These sensors can be used to measure finely the temperature that is lower than 200℃ with aluminium coating.

Temperature dependence of the refractive index of optical fibers

Many experimental investigations on the temperature dependence of the refractive index of optical fibers have been reported previously, however a satisfying theoretical explanation for it is still absent. In this paper, a theoretical model about the temperature dependence of the refractive index of optical fibers is presented and it is in agreement with the previous experimental results. This work is a significant reference for the research and development of temperature sensors based on optical fiber delay lines.

Mathematical Model of Fiber Optic Temperature Sensor Based on Optic Absorption and Experiment Testing

On the basis of analysis on the temperature monitoring methods for high voltage devices, a new type of fiber optic sensor structure with reference channel is given. And the operation principle of fiber optic sensor is analysed at large based on the absorption of semiconductor chip. The mathematical model of both devices and the whole system are also given. It is proved by the experiment that this mathematical model is reliable.

Fiber Optic Sensors and Sensor Networks Using a Time-domain Sensing Scheme

Fiber loop ringdown (FLRD) has demonstrated to be capable of sensing various quantities, such as chemical species, pressure, refractive index, strain, temperature, etc.;and it has high potential for the development of a sensor network. In the present work, we describe design and development of three different types of FLRD sensors for water, cracks, and temperature sensing in concrete structures. All of the three aforementioned sensors were indigenously developed very recently in our laboratory and their capabilities of detecting the respective quantities were demonstrated. Later, all of the sensors were installed in a test grout cube for real-time monitoring. This work presents the results obtained in the laboratory-based experiments as well as the results from the real-time monitoring process in the test cube.

An all optical fiber gas sensor of NH3 and CO based on based on the spectral absorption and harmonic detection

An all optical fiber gas sensor is presented to detect the concentration of NH3 and CO. Based on the spectral absorption, The wideband light source is used to reflect two narrowband spectra by fiber grating of different duty. and piezoelectric ceramics to obtain narrowband output light. The high sensitivity detection can be measured from the second harmonic signal. The two narrowband spectra are corresponding to the absorption spectra of NH3 and CO. Concentration detection are realized by the detection of variety of light intensity. Sensitivity is proved and cost is reduced.

Landslide Monitoring Based on High-Resolution Distributed Fiber Optic Stress Sensor

A landslide monitoring application is presented by using a high-resolution distributed fiber optic stress sensor. The sensor is used to monitor the intra-stress distribution and variations in landslide bodies, and can be used for the early warning of the occurrence of the landslides. The principle of distributed fiber optic stress sensing and the intra-stress monitoring method for landslides are described in detail. By measuring the distributed polarization mode coupling in the polarization-maintaining fiber, the distributed fiber stress sensor with stress measuring range 0 to 15 MPa, spatial resolution 10 cm and measuring range 0.5 km, is designed. The warning system is also investigated experimentally in the field trial.