A Two-Layer Fuzzy Control Strategy for the Participation of Energy Storage Battery Systems in Grid Frequency Regulation

To address the frequency fluctuation problem caused by the power dynamic imbalance between the power system and the loadwhen a large number of newenergy sources are connected to the grid,a two-layer fuzzy control strategy is proposed for the participation of the energy storage battery system in FM.Firstly,considering the coordination of FM units responding to automatic power generation control commands,a comprehensive allocation strategy of two signals under automatic power generation control commands is proposed to give full play to the advantages of two FM signals while enabling better coordination of two FM units responding to FM commands;secondly,based on the grid FM demand and battery FM capability,a double-layer fuzzy control strategy is proposed for FM units responding to automatic power generation control commands in a coordinated manner under dual-signal allocation mode to precisely allocate the power output depth of FM units,which can control the fluctuation of frequency deviation within a smaller range at a faster speed while maintaining the battery charge state;finally,the proposed Finally,the proposed control strategy is simulated and verified inMatlab/Simulink.The results show that the proposed control strategy can control the frequency deviation within a smaller range in a shorter time,better stabilize the fluctuation of the battery charge level,and improve the utilization of the FM unit.

Coupling characteristics of laterally coupled gratings with slots

Laterally-coupled ridge-waveguide distributed feedback lasers fabricated without epitaxial regrowth steps have the advantages of process simplification and low cost.We present a laterally coupled grating with slots.The slots etched between the ridge and grating area are designed to suppress the lateral diffusion of carriers and to reduce the influence of the aspect-ratio-dependent-etching effect on the grating morphology in the etching process.Moreover,the grating height in this structure can be decreased to lower the aspect ratio significantly,which is advantageous over the conventional laterally coupled ridge waveguide gratings.The effects of five main structural parameters on the coupling characteristics of gratings are studied by MODE Solutions.It is found that varying the lateral width of the grating can be used as an effective way to tune the coupling strength;narrow slots(100 nm and 300 nm)and wide ridge(2μm–4μm)promote the stability of grating coupling coefficient and device performance.It is important to note that the grating bottom should be fabricated precisely.The comparative study of carrier distribution and mode field distribution shows that the introduction of narrow slots can strengthen the competitive advantage and stability of the fundamental mode.

FUZZY STABILITY ANALYSIS OF MODE COUPLING CHATTER ON CUTTING PROCESS

The influence of fuzzy uncertainty factors is considered on the analysis of chatter occurring during machine tool cutting process. Using fuzzy mathematics analysis methods, a detailed discussion over fuzzy stability analysis problems is presented related to the mode coupling chatter with respect to intrinsic structure fuzzy factors, and the possibility distribution of the fuzzy stability cutting range and the confidence level expressions of the fuzzy stability cutting width are given.

Numerical analysis of residence time distribution of solids in a bubbling fluidized bed based on the modified structure-based drag model

The residence time distribution （RTD） of solids and the fluidized structure of a bubbling fluidized bed were investigated numerically using computational fluid dynamics simulations coupled with the modified structure-based drag model. A general comparison of the simulated results with theoretical values shows reasonable agreement. As the mean residence time is increased, the RTD initial peak intensity decreases and the RTD curve tail extends farther. Numerous small peaks on the RTD curve are induced by the back- mixing and aggregation of particles, which attests to the non-uniform flow structure of the bubbling fluidized bed. The low value of t50 results in poor contact between phases, and the complete exit age of the overflow particles is much longer for back-mixed solids and those caught in dead regions. The formation of a gulf-stream flow and back-mixing for solids induces an even wider spread of RTD.

Measurement, modelling, and closed-loop control of crystal shape distribution： Literature review and future perspectives

Crystal morphology is known to be of great importance to the end-use properties of crystal products, and to affect down-stream processing such as filtration and drying. However, it has been previously regarded as too challenging to achieve automatic closed-loop control. Previous work has focused on controlling the crystal size distribution, where the size of a crystal is often defined as the diameter of a sphere that has the same volume as the crystal. This paper reviews the new advances in morphological population balance models for modelling and simulating the crystal shape distribution （CShD）, measuring and estimating crystal facet growth kinetics, and two- and three-dimensional imaging for on-line characterisation of the crystal morphology and CShD. A framework is presented that integrates the various components to achieve the ultimate objective of model-based closed-loop control of the CShD. The knowledge gaps and challenges that require further research are also identified.

Polarization Mode Dispersion Probability Distribution for Arbitrary Mode Coupling

The probability distribution of the differential group delay for arbitrary mode coupling is simulated with Monte-Carlo method. Fitting the simulation results, we obtain probability distribution function for arbitrary mode coupling.

Simulation of gas-solid flow in sinter vertical cooling furnace

The velocity distribution of sinter and gas in vertical cooling furnace(VCF)has an important influence on gas-solid heat transfer.Based on the slot model of single hopper in the VCF of Meishan Iron and Steel Co.,Ltd.,the velocity and particle size distribution of sinter and the velocity and pressure distribution of gas were studied using a computational fluid dynamics-discrete element method model to obtain the gas-solid flow rule in the VCF.The results showed that the velocity of sinter near the wall and the edge of vent cowl was lower than that in the rest of the same plane.Therefore,the rectangular section of the vertical cooling furnace can be divided into a quasi-static zone,a plug flow zone and a convergent flow zone according to the flow velocity of the sinter.The average particle size and the void fraction of sinter bed were distributed in"W"and"V"shape along the width direction,respectively.The distribution of gas velocity in the furnace cavity was uneven,and the high-velocity area gradually changed from the center to the edge of the furnace cavity with the rise of gas.Reducing the ratio of edge to center gas flow from 2.7∶1 to 0.7∶1 could improve the gas velocity,but could not change the gas velocity distribution.The gas velocity distribution was more affected by the average particle size distribution of the sinter bed.It was suggested that measures need be taken to adjust it to improve the gas velocity distribution in the VCF.

Novel parametric optimum processing method for airborne radar

In radar target detection, an optimum processor needs to automatically adapt its weights to the environment change. Conventionally, the optimum weights are obtained by substantial independently and identically distributed (i.i.d.) interference samplings, which is not always realistic in an inhomogeneous clutter background of airborne radar. The lack of i.i.d. samplings will inevitably lead to performance deterioration for optimum processing. In this paper, a novel parametric adaptive processing method is proposed for airborne radar target detection based on the modified Doppler distributed clutter (DDC) model with contribution of clutter's internal motion. It is different from the conventional methods in that the adaptive weights are determined by two parameters of DDC model, i.e., angular center and spread. A low-complexity nonlinear operators approach is also proposed to estimate these parameters. Simulation and performance analysis are also provided to show that the proposed method can remarkably reduce the dependence of i.i.d. samplings and it is computationally efficient for practical use.