Reactive jet density distribution effect on its penetration behavior

In this paper,the penetration mechanism of reactive jet with non-uniform density distribution is studied.The simulations show that the density deficit occurs in the whole reactive jet,and the density increases from the jet tip to tail.The density of jet tip is approximately 1.5 g/cm3,which is lower than that of the reactive liner materials.The X-ray experiments show similar results with the simulations.The density decreasing effect of jet tip has a significant influence on the penetration behavior when the reactive jet impacts steel plate.According to the simulation results,this paper assumes that the density gradient in the jet section has linear distribution.Then,the deflagration pressure generated by each jet element at the bottom of crater is introduced into the Bernoulli equation.Based on the virtual origin model and Szendrei-Held equation,the analytical models for penetration depth and radial cratering of reactive jet with the density reduction are obtained.Moreover,to further prove the validity of analytical models,the penetration experiments of the reactive liner shaped charge against steel plate under different standoffs are carried out.There is a convergence between the analytical crater profiles and experimental results when reactive jets penetrate steel plates under different standoffs,especially at standoff of 1.5 and 2.0charge diameters.

Numerical Simulation of Current Density Distribution in Keyhole Double-Sided Arc Welding

In the double-sided arc welding system (DSAW) composing of PAW+TIG arcs, the PAW arc is guided by the TIG arc so that the current mostly flows through the direction of the workpiece thickness and the penetration is greatly improved. To analyze the current density distribution in DSAW is beneficial to understanding of this process. Considering all kinds of dynamic factors acting on the weldpool, this paper discusses firstly the surface deformation of the weldpool and the keyhole formation in PAW+TIG DSAW process on the basis of the magnetohydrodynamic theory and variation principles. Hence, a model of the current density distribution is developed. Through numerical simulation, the current density distribution in PAW+TIG DSAW process is quantitatively analyzed. It shows that the minimal radius of keyhole formed in PAW+TIG DSAW process is 0.5 mm and 89.5 percent of current flows through the keyhole.

Prediction of nuclear charge density distribution with feedback neural network

Nuclear charge density distribution plays an important role in both nuclear and atomic physics,for which the two-parameter Fermi(2pF)model has been widely applied as one of the most frequently used models.Currently,the feedforward neural network has been employed to study the available 2pF model parameters for 86 nuclei,and the accuracy and precision of the parameter-learning effect are improved by introducing A^(1∕3)into the input parameter of the neural network.Furthermore,the average result of multiple predictions is more reliable than the best result of a single prediction and there is no significant difference between the average result of the density and parameter values for the average charge density distribution.In addition,the 2pF parameters of 284(near)stable nuclei are predicted in this study,which provides a reference for the experiment.

Three-dimensional crustal density distribution beneath North China by sequential inversion of local earthquake traveltimes and gravity anomaly

A three-dimensional crustal density model beneath North China is determined using P-wave traveltimes and gravity datum by sequential inversion method in this paper. To improve the uniqueness of the solution, we used a linear relationship between velocity and density to achieve mutual conversions and constraints between velocity difference and density difference. Algebraic reconstruction technique （ART） was used in density inversion, which highly improved the calculation speed comparing with common least squares method. The inversion results indicate that the crustal density beneath North China is extremely inhomogeneous with its distribution coherent with regional tectonics. The lower crust of Taihang mountain tectonic zone shows an obvious low density characteristic. We proposed that it may be an indicator of upwelling of mantle materials or partial melting of lowermost crust.

Ion Density Distribution in an Inductively Coupled Plasma Chamber

The ion density distribution in the reaction chamber was diagnosed by a Langmuir probe. The rules of the ion density distribution were obtained under the pressures of 9 Pa, 13 Pa, 27 Pa and 53 Pa in the reaction chamber, different radio-frequency powers and different positions. The result indicates that the ion density decreases as the pressure increases, and increases as the power decreases. The ion density of axial position z =0 achieves 5.8×1010 on the center of coil under the power of 200 w and pressure of 9 Pa in the reaction chamber.

Plating current density distribution of lithium metal anodes in pouch cells

The uniformity of current density distribution upon electrodes is one of the most important factors determining the lithium dendrites growth and cycling performance of lithium metal batteries(LMBs). Herein,current density distributions of lithium metal anodes induced by various engineering factors, consisting of uneven cathode, electrolyte distribution, and different tab positions, and their effects on the electrochemical performance are investigated theoretically and experimentally in pouch cells. The deviation of current density in lithium metal anodes ranges from 2.47% to 196.18% due to the different levels of uneven cathode materials. However, the deviation is just 13.60% for different electrolyte thicknesses between cathodes and anodes, even a ten-layer separator in some positions. The maximum deviation for variational tab positions is only 0.17%. The nonuniformity in current density distribution results in severe dendrite growth issues and poor electrochemical performance of LMBs. This work not only confirms the direct correlation between the uneven current density distribution and lithium deposition behaviors, but also points out the decisive effects of cathode surface roughness on current distribution of anodes, to which more attentions should be paid in practical applications of LMBs.

INVESTIGATION ON THE DENSITY UNIFORMITY OF PRESSED PARTS BY LOW-VOLTAGE ELECTROMAGNETIC COMPACTION

Powder metallurgy is an efficient approach to fabricate varieties of high performance structure materials, function materials and special materials working under limited conditions. Research and development of new efficient technology to form high-density, high-performance and net shape parts is a key to widen application and development of powder materials. Recently, the low-voltage electromagnetic compaction (EMC) has been used by present authors to compacted copper, tin, aluminum powders and the products with 99% relative density have been acquired. In this work, the research has been extended to investigation on the density uniformity of pressed parts. The analysis results show that the density of the part compacted by low-voltage EMC decreases gradually in press direction as static compaction. But it is higher and more homogeneous. The density of the top part increases gradually from the center to the outer, which is just reversal of the bottom part. In some extent, the higher the discharging voltage is, the higher the density is and the more homogeneous the distribution is. In addition, repetitive compaction can improve the density of powder parts and the distribution uniformity.

Effects of drive current rise-time and initial load density distribution on Z-pinch characteristics

A two-dimensional, three-temperature radiation magneto-hydrodynamics model is applied to the investigation of evolutional trends in x-ray radiation power, energy, peak plasma temperature and density as functions of drive current rise-time and initial load density distribution by using the typical experimental parameters of tungsten wire-array Z- pinch on the Qiangguang-I generator. The numerical results show that as the drive current rise-time is shortened, x-ray radiation peak power, energy, peak plasma density and peak ion temperature increase approximately linearly, but among them the x-ray radiation peak power increases more quickly. As the initial plasma density distribution in the radial direction becomes gradually flattened, the peak radiation power and the peak ion-temperature almost exponentially increase, while the radiation energy and the peak plasma density change only a little. The main effect of shortening drive current rise-time is to enhance compression of plasma, and the effect of flattening initial load density distribution in the radial direction is to raise the plasma temperature. Both of the approaches elevate the x-ray peak radiation power

Root length density distribution and associated soil water dynamics for tomato plants under furrow irrigation in a solar greenhouse

Furrow irrigation is a traditional widely-used irrigation method in the world. Understanding the dynamics of soil water distribution is essential to developing effective furrow irrigation strategies, especially in water-limited regions. The objectives of this study are to analyze root length density distribution and to explore soil water dynamics by simulating soil water content using a HYDRUS-2D model with consideration of root water uptake for furrow irrigated tomato plants in a solar greenhouse in Northwest China. Soil water contents were also in-situ observed by the ECH_2O sensors from 4 June to 19 June and from 21 June to 4 July, 2012. Results showed that the root length density of tomato plants was concentrated in the 0–50 cm soil layers, and radiated 0–18 cm toward the furrow and 0–30 cm along the bed axis. Soil water content values simulated by the HYDRUS-2D model agreed well with those observed by the ECH_2O sensors, with regression coefficient of 0.988, coefficient of determination of 0.89, and index of agreement of 0.97. The HYDRUS-2D model with the calibrated parameters was then applied to explore the optimal irrigation scheduling. Infrequent irrigation with a large amount of water for each irrigation event could result in 10%–18% of the irrigation water losses. Thus we recommend high irrigation frequency with a low amount of water for each irrigation event in greenhouses for arid region. The maximum high irrigation amount and the suitable irrigation interval required to avoid plant water stress and drainage water were 34 mm and 6 days, respectively, for given daily average transpiration rate of 4.0 mm/d. To sum up, the HYDRUS-2D model with consideration of root water uptake can be used to improve irrigation scheduling for furrow irrigated tomato plants in greenhouses in arid regions.

Electron density distribution of LiMn_(2)O_(4)cathode investigated by synchrotron powder x-ray diffraction

Electron density plays an important role in determining the properties of functional materials.Revealing the electron density distribution experimentally in real space can help to tune the properties of materials.Spinel Li Mn2 O4 is one of the most promising cathode candidates because of its high voltage,low cost,and non-toxicity,but suffers severe capacity fading during electrochemical cycling due to the Mn dissolution.Real-space measurement of electron distribution of Li Mn2 O4 experimentally can provide direct evaluation on the strength of Mn–O bond and give an explanation of the structure stability.Here,through high energy synchrotron powder x-ray diffraction(SPXRD),accurate electron density distribution in spinel Li Mn2 O4 has been investigated based on the multipole model.The electron accumulation between Mn and O atoms in deformation density map indicates the shared interaction of Mn–O bond.The quantitative topological analysis at bond critical points shows that the Mn–O bond is relatively weak covalent interaction due to the oxygen loss.These findings suggest that oxygen stoichiometry is the key factor for preventing the Mn dissolution and capacity fading.

Study on the Two-Dimensional Density Distribution for Gas Plasmas Driven by Laser Pulse

We perform an experimental study of two-dimensional（2D） electron density profiles of the laser-induced plasma plumes in air by ordinarily laboratorial interferometry. The electron density distributions measured show a feature of hollow core. To illustrate the feature, we present a theoretical investigation by using dynamics analysis. In the simulation, the propagation of laser pulse with the evolution of electron density is utilized to evaluate ionization of air target for the plasma-formation stage. In the plasma-expansion stage, a simple adiabatic fluid dynamics is used to calculate the evolution of plasma outward expansion. The simulations show good agreements with experimental results, and demonstrate an effective way of determining 2D density profiles of the laser-induced plasma plume in gas.

Reconstruction of Ionization Density Distribution in Hall Thruster Channel from Ion Energy Spectrum of Plasma Jet

Propellant ionization in the Hall thruster discharge channel is a significant process and has strong influence on the thruster＇s efficiency. In this work, the functional relation has been established between the ionization density distribution and the function of the ion energy distribution through the basic equations governing the ion flow in the Hall thruster channel and the method achieved for reconstructing the ionization density distribution inside the channel by ordinary plasma diagnosis of the potential distribution and ion energy spectrum of the plasma jet. The ionization density distributions of single and double charged ions in an ATON-thruster channel have been reconstructed according to the experimental data of the potential distribution along the axis of the channel and the ion energy spectrum of the plasma jet. The agreement between the calculation and experimental results of the percentage of double charged ions proves the validity of our method achieved in this work.

Bridge density functional approximation for non-uniform hard core repulsive Yukawa fluid

In this work, a bridge density functional approximation （BDFA） （J. Chem. Phys. 112, 8079 （2000）） for a nonuniform hard-sphere fluid is extended to a non-uniform hard-core repulsive Yukawa （HCRY） fluid. It is found that the choice of a bulk bridge functional approximation is crucial for both a uniform HCRY fluid and a non-uniform HCRY fluid. A new bridge functional approximation is proposed, which can accurately predict the radial distribution function of the bulk HCRY fluid. With the new bridge functional approximation and its associated bulk second order direct correlation function as input, the BDFA can be used to well calculate the density profile of the HCRY fluid subjected to the influence of varying external fields, and the theoretical predictions are in good agreement with the corresponding simulation data. The calculated results indicate that the present BDFA captures quantitatively the phenomena such as the coexistence of solid-like high density phase and low density gas phase, and the adsorption properties of the HCRY fluid, which qualitatively differ from those of the fluids combining both hard-core repulsion and an attractive tail.

A STUDY ON THE INTERACTION BETWEEN CH_3OH AND H_2CO MOLECULES IN TERMS OF THE PROPERTIES OF CHARGE DENSITY DISTRIBUTIONS

Two possible complexes formed by the interaction of CH_3OH and H_2CO,one hydrogen-bonded (Ⅰ)and one donor-acceptor complex(Ⅱ),have been reported in the previous paper.Based on the ab initio 6-31G basis set calculations,the properties of the charge density for the complexeshave been analyzed using the theory of atoms in molecules.The nature of the complex formation has been discussed in terms of the properties of the charge density distributions.

Relationship between Power Density Distribution and Homogenization of Diamond Film in the Multifilament CVD System

Periodical macro stripes have been found on diamond film prepared on a Si substrate by the multifilament chemical vapor deposition (CVD) method when the filament substrate distance is less than 2 mm. The properties of the stripe on the film were characterized qualitatively by a scanning electron microscope (SEM) and Raman scattering spectrometer. The measurement results show that this stripe corresponds to the different kinds of the microstructure and thickness of the film. Through calculation of the thermal radiation energy density distribution on the surface of substrate, this phenomenon can be explained successfully.

Research of Trap and Electron Density Distributions in the Interface of Polyimide/Al2O3 Nanocomposite Films Based on IDC and SAXS

The distributions of traps and electron density in the interfaces between polyimide （PI） matrix and Al2O3 nanoparticles are researched using the isothermal decay current and the small-angle x-ray scattering （SAXS） tests. According to the electron density distribution for quasi two-phase mixture doped by spherical nanoparticles, the electron densities in the interfaces of PI/Al2O3 nanocomposite films are evaluated. The trap level density and carrier mobility in the interface are studied. The experimental results show that the distribution and the change rate of the electron density in the three layers of interface are different, indicating different trap distributions in the interface layers. There is a maximum trap level density in the second layer, where the maximum trap level density for the nanocomposite film doped by 25 wt% is 1.054 × 10^22 eV·m^-3 at 1.324eV, resulting in the carrier mobility reducing. In addition, both the thickness and the electron density of the nanocomposite film interface increase with the addition of the doped Al2O3 contents. Through the study on the trap level distribution in the interface, it is possible to further analyze the insulation mechanism and to improve the performance of nano-dielectric materials.

Gravity effect calculation of threedimensional linear density distribution andits application

An algorithm for calculating gravity effect of three-dimensional (3D) linear density distribution is presented in this paper. The linear continuous density distribution is represented with 3D grid model, which has a resemblance to the velocity model used in some seismic tomography codes. The consensus in representation method of density model and velocity model facilitates the seismic-gravity-integrated interpretation or simultaneous inversion. The numerical test of synthetic data shows that although the analytical gravity formula for linear density distribution is more complex than that for piecewise constant density distribution, it takes less time to calculate the gravity effect with linear density model than that with piecewise constant density model. In addition, this method is used in the integrated interpretation of 3D seismological tomography and gravity data in Dabie Mountain area.

South-north asymmetry of proton density distribution in the Martian magnetosheath

We perform a statistical analysis of data from the Mars Atmosphere and Volatile Evolution (MAVEN) project on the global distribution of protons in the Martian magnetosheath. Our results show that the proton number density distribution has a south-north asymmetry. This south-north asymmetry is most likely caused by the south-north asymmetric distributions of the crustal magnetic fields at Mars. The strong crustal magnetic fields push the inner boundary of magnetosheath to a higher altitude in the southern hemisphere. Due to the outward movement of the inner boundary of the magnetosheath, a compressed magnetosheath forms, causing subsequent increases in proton number density, thermal pressure, and total pressure. Eventually, a balance is reached between the increased total pressure inside the magnetosheath and the increased magnetic pressure inside the induced magnetosphere. Our statistical study suggests that the Martian crustal magnetic fields can strongly affect the proton number density distribution in the Martian magnetosheath.

Effect of Distribution of Magnetic Flux Density on Purifying Liquid Metal by Travelling Magnetic Field

The distribution of the magnetic flux density in the magnetic field generator which provided travelling magnetic field was determined. The experiments using liquid gallium and aluminum silicon alloy to observe the turbulent flow or remove inclusions were performed to obtain the basic principles how the distribution of the magnetic flux density took effect on removing inclusions from molten metal by electromagnetic field. The suitable area in the field for purifying metal was suggested.

Experimental study on the mitigation effect of mangroves during tsunami wave propagation

Mangroves are crucial for protecting coastal areas against extreme disasters such as tsunamis and storm surges.An experimental study was conducted to determine how mangroves can mitigate the tsunami wave propagation.The test was performed in a flume, where mangrove models were installed on a slope, and dam-burst waves were used to simulate tsunami waves. To study how mangrove forests reduce the impact of tsunamis, this paper measured the heights of the incoming waves under different initial conditions(tsunami wave intensity and initial water depth) and plant factors(arrangement and distribution density) and described the reduction process. The results show that, after passing through the mangrove, the tsunami bore height will decrease within a certain range as the initial water depth increases. However, there is no correlation between the increase of inundation level and the drop of water level. The bore height attenuation is more significant at higher density of mangroves,but after tsunami passing through the mangroves, the relative bore height will decrease. When the distribution density of mangroves is constant, the wave attenuation at different locations(before, on and after the slope)shows different relationships with the initial water depth and wave height for different models. The transmission coefficient(K_(i)) shows a parabolic correlation with its density. The proportion of the energy loss caused by the mangrove resistance to the total energy(E_(b)) is defined as C_(m2). The variation trend of C_(m2) corresponds to the tsunami wave energy attenuation rate(C_(a)) and K_(i).