Analysis of Mobile and Internet Network Coverage: Propagation of Electromagnetic Waves and Concept of Digital Divide in Burundi

Mobile and Internet network coverage plays an important role in digital transformation and the exploitation of new services. The evolution of mobile networks from the first generation (1G) to the 5th generation is still a long process. 2G networks have developed the messaging service, which complements the already operational voice service. 2G technology has rapidly progressed to the third generation (3G), incorporating multimedia data transmission techniques. It then progressed to fourth generation (4G) and LTE (Long Term Evolution), increasing the transmission speed to improve 3G. Currently, developed countries have already moved to 5G. In developing countries, including Burundi, a member of the East African Community (ECA) where more than 80% are connected to 2G technologies, 40% are connected to the 3G network and 25% to the 4G network and are not yet connected to the 5G network and then still a process. The objective of this article is to analyze the coverage of 2G, 3G and 4G networks in Burundi. This analysis will make it possible to identify possible deficits in order to reduce the digital divide between connected urban areas and remote rural areas. Furthermore, this analysis will draw the attention of decision-makers to the need to deploy networks and coverage to allow the population to access mobile and Internet services and thus enable the digitalization of the population. Finally, this article shows the level of coverage, the digital divide and an overview of the deployment of base stations (BTS) throughout the country to promote the transformation and digital inclusion of services.

Optimization of DC Resistance Divider Up to 1200 kV Using Thermal and Electric Field Analysis

Self-heating and electric field distribution are the primary factors affecting the accuracy of the Ultra High Voltage Direct Current(UHVDC)resistive divider.Reducing the internal temperature rise of the voltage divider caused by self-heating,reducing the maximum electric field strength of the voltage divider,and uniform electric field distribution can effectively improve the UHVDC resistive divider’s accuracy.In this paper,thermal analysis and electric field distribution optimization design of 1200 kV UHVDC resistive divider are carried out:(1)Using the proposed iterative algorithm,the heat dissipation and temperature distribution of the high voltage DC resistive divider are studied,and the influence of the ambient temperature and the power of the divider on the temperature of the insulating medium of the divider is analyzed;(2)Established the finite element models of 1200 kV and 2×600 kV DC resistive dividers,analyzed the influence of the size of the grading ring and the installation position on the maximum electric field strength of the voltage divider,and calculated the impact of the shielding resistor layer on the vicinity of the measuring resistor layer.The research indicates that:(1)The temperature of the insulating medium is linearly related to the horsepower of the voltage divider and the ambient temperature;(2)After the optimized design of the electric field,the maximum electric field strength of the 1200 kV DC resistive divider is reduced to 1471 V/mm,which is about 24% lower than that of the unoptimized design;(3)Installing the shielding resistor layer can significantly improve the electric field near the measuring resistor layer.This paper has an important reference function for improving the accuracy of the UHVDC resistive divider.

A Miniaturized Broadband Wilkinson Power Divider Using Micro-Strip Branch Lines

A miniaturized broadband Wilkinson power divider is proposed. Micro-strip branch lines are introduced to replace multiple resistors used in multi-stage Wilkinson power dividers to increase the bandwidth of single-stage Wilkinson power dividers. To demonstrate its performance, an improved single-stage Wilkinson power divider with four micro-strip branch lines was designed. Simulated results show that the insert loss is better than 3.2 dB, the input return loss, output return loss, and isolation are better than 15 dB respectively, across a 76% bandwidth from 18 to 40 GHz. .

A Programmable 2.4GHz CMOS Multi-Modulus Frequency Divider

A programmable multi-modulus frequency divider is designed and implemented in a 0. 35μm CMOS process. The multi-modulus frequency divider is a single chip with two dividers in series,which are divided by 4 or 5 prescaler and by 128-255 multi-modulus frequency divider. In the circuit design, power and speed trade-offs are analyzed for the prescaler, and power optimization techniques are used according to the input frequency of each divider cell for the 128-255 multimodulus frequency divider. The chip is designed with ESD protected I/O PAD. The dividers chain can work as high as 2.4GHz with a single ended input signal and beyond 2.6GHz with differential input signals. The dual-modulus prescaler consumes 11mA of current while the 128-255 multi-modulus frequency divider consumes 17mA of current with a 3.3V power supply. The core area of the die without PAD is 0.65mm × 0.3mm. This programmable multi-modulus frequency divider can be used for 2.4GHz ISM band PLL-based frequency synthesizers. To our knowledge, this is the first reported multi-modulus frequency divider with this structure in China.

Integrated Low-Power CMOS VCO and Its Divide-by-2 Dividers

An integrated low power CMOS VCO and its divide by 2 dividers for WLAN transceivers are presented.The VCO is based on on chip symmetrical spiral inductor and differential diode and the divide by 2 dividers are based on the ILFD technique.Due to differential LC tanks and ILFD techniques,power consumption is low.The circuit is implemented in a 0 18μm CMOS process.Measurements show the proposed circuit could produce 3 6/1 8GHz dual band LO signals with a wide tuning range and low phase noise.1 8GHz LO signals are quadrature.It consumes 5mA at V DD =1 5V.The size of die area is only 1 0mm×1 0mm.

0.18μm CMOS programmable frequency divider design for DVB-T

The implementation of a programmable frequency divider, which is one of the components of the phase-locked loop （PLL） frequency synthesizer for digital video broadcastingterrestrial （DVB-T） and other modem communication systems, is presented. By cooperating with a dual-modulus prescaler, this divider can realize an integer frequency division from 926 to 1 387. Besides the traditional standard cell design flow, such as logic synthesis, placement and routing, the interactions between front-end and back-end are also considered to optimize the design flow under deep submicron technology. By back-annotating the back-end information to front-end design, a custom wire-load model is created which is more practical compared with the default model. This divider has been fabricated in TSMC 0. 18μm CMOS technology using Artisan standard cell library. The chip area is 675 μm × 475 μm and the power consumption is about 2 mW under a 1.8 V power supply. Measurement results show that it works correctly and can realize a frequency division with high precision.

An 8.5GHz 1∶8 Frequency Divider in 0.35μm CMOS Technology

An 1∶8 frequency divider is designed and realized in a 0 35μm standard CMOS technology.The chip consists of three stages of 1∶2 divider cells,which are constructed with source couple logic (SCL) flip flops.By revising the traditional topology of SCL flip flop,a divider with better performances is got.The results of measurement show that the whole chip achieves the frequency division at more than 8 5GHz.Each 1∶2 divider consumes about 11mW from a 3 3V supply.The divider can be used in RF and optic fiber transceivers and other high speed systems.

The Art of Power Dividing:A Review for State-of-the-Art Planar Power Dividers

In this paper,massive state-of-theart planar power dividers are presented and discussed. The innovations of these superiorly-performanced power dividers lie in the performance breakthrough,physical configurations and function integrations. Eventually,based on the trend presented,the future of the power dividers is predicted. This paper might have inspiration significance to illuminate the way for the development of power dividers.

Design of a Frequency Divider with Reduced Complexity Based on a Resonant Tunneling Diode

A novel edge-triggered D-flip-flop based on a resonant tunneling diode （RTD） is proposed and used to construct a binary frequency divider. The design is discussed in detail and the performance of the circuit is verified using SPICE. Relying on the nonlinear characteristics of RTD,we reduced the number of components used in our DFF circuit to only half of that required using conventional CMOS SCFL technology.

A Low Power,High Sensitivity SiGe HBT Static Frequency Divider up to 90 GHz for Millimeter-Wave Application

A layout and connection optimization for static frequency divider is presented. The layout optimization provides a new circle topology transistors placement and reasonable connection structure, which reduces the parasitic effectively and enables self-oscillation frequency enhancement. Besides, bandwidth enhancement techniques based on a center-tap capacitor in input balun design and inductive peaking in latch design are adopted to improve further high frequency performance with low power consumption. As a proof of concept, design of a divide-by-2 static frequency divider in 0.13 μm SiGe BiCMOS technology is reported. With single-ended input clock signal, the divider is measured to be operated from 40 to 90 GHz. Phase noise measurements of a 90 GHz input clock signal indicate ideal behavior with no measurable noise contribution from the divider. The divider followed by a buffer that can deliver more than-10 dBm output power, which is sufficient to drive succeeding stage. To the author's knowledge, the divider exhibits a competitive power dissipation and the highest FOM among silicon based frequency dividers that operating higher than 70 GHz.

Design of 0.18 μm CMOS programmable frequency divider based on standard cells

The design of a programmable frequency divider, which is one of the components of the phase-locked loop （PLL） frequency synthesizer for transmitter and receiver in IEEE 802. 11 a standard, is investigated. The main steps in very large-scale integration （VLSI） design flow such as logic synthesis, floorplan and placement ＆ routing （P ＆ R） are introduced. By back-annotating the back-end information to the front-end design, the custom wire-load model is created and used for optimizing the design flow under deep submicron technology. The programmable frequency divider is implemented based on Artisan TSMC （Taiwan Semicoductor Manufacturing Co. Ltd. ）0. 18μm CMOS （complementary metal-oxide-semiconductor） standard cells and fabricated. The Chip area is 1 360. 5μm^2 and can work in the range of 100 to 200 MHz. The measurement results indicate that the design conforms to the frequency division precision.

Compact UWB Power Divider, Analysis and Design

In this paper, two ultra-wide band power dividers are introduced. Compact equal power divider is considered firstly where an extended transmission lines and double open stubs are used in order to increase the bandwidth. Secondly, an unequal UWB power divider is introduced where multi-stage impedance is used. The proposed power dividers are fabricated and measured. The overall sizes of the proposed power dividers are 11.37 × 17.87 mm2 for the equal one and 12.13 × 29.03 mm2 for the unequal power divider. The simulated results are compared with the measured results and good agreement is obtained.

A power divider based on a new kind of composite right/left-handed transmission line (CRLH TL) unit

A new power divider, composed of a novel composite right/left-handed (CRLH) transmission line (TL) unit, is proposed. The properties of the power divider based on four CRLH TL unit cells are investigated theoretically. By adjusting the parameters of the capacitors and the inductors, the power divider shows perfectly symmetric power division at 5.13 GHz, return loss up to ?24 dB, with the transmitted power being close to ?3.1 dB. The phenomena are demonstrated by simulation results. Being compact in size and low-cost, the proposed power divider is very suitable for microwave and millimeter wave integrated circuits.

The Formation Logic of the Digital Divide and Feasible Ways to Cross It:An Access-Based Analysis

How enterprises overcome the digital divide in a digital economy is a topic related to efficiency and fairness.The formation of the digital divide has showcased a certain level of objectivity and is also influenced by the characteristics of enterprises themselves.Based on the model that expands the information and communication technology(ICT)access,concept,we explored the digital divide’s formation logic of the digital divide and feasible ways to cross it.Our findings shed light on its formation logic,which includes elements of the subjective will of enterprises to transform,the fear of transformation,the dependence on development paths,and the cost of using digital technology,all of which have contributed to disparities in enterprises’motivational access.In addition,differences in the construction of digital infrastructure,financial strengths,business models,and heterogeneity in cluster networks have led to differences in enterprises’material access.The absorptive capacity of enterprises has affected their skill access,while the management capability influences the application access of enterprises.We also found that crossing the digital divide requires the joint efforts of governments,markets,and enterprises in the four access dimensions.

A fractional frequency divider based on phase switching and negative feedback delta-sigma modulator for MMMS applications

A fractional frequency divider based on phase switching and negative feedback delta-sigma modulator(NF-DSM) is presented. The phase switching circuit, realized by switching 8 signals generated by a divider-by-4 circuit, is adopted to reduce the frequency division step. The NF-DSM, which can obtain smooth output spectra, is proposed to generate the fractional part of the division ratio, moreover, the integer part of the division ratio is realized by a divider-by-2/3 circuit chain. Fabricated in TSMC 0.18 μm RF CMOS technology, the fractional frequency divider achieves a measured operation frequency from 0.5 GHz to 8 GHz. With a 1.8 V supply voltage, the maximum current consumption of the whole divider is 17.5 mA, and the chip area is 0.58 mm^2, including the pads.

Innovation in the Public Sector in the Start-up Nation:Challenges of Technology,Bureaucracy,and Digital Divide

Innovation provides opportunities to all countries,as advancement in technology and globalization of economic markets encourage global competition and increase the role of governments in gaining a strategic competitive advantage while boosting economic growth and productivity.According to the OECD,innovation can make a difference in addressing developmental challenges and providing catalyst for countries to accelerate business processes and practices that improve public service efficiency.The public sector plays a significant role in modern economies and innovation is a necessary condition for improving government services to the public and creating a competitive economy.Israel is known as the“start-up nation”,but innovation policies and strategies relating to the public sector are less developed than those of business innovation due to lack of innovation culture,digital divide,and bureaucracy.The research examines innovation in the public sector in Israel compared to other OECD countries.It is argued that despite the enormous influence of high-tech and start-ups on the economy and gross of national product,the flourishing technology sector has not contributed to other sectors of the economy and the performance of the public service lags behind the private sector in terms of innovation and efficiency.The research concludes that implementing Israel’s success in business innovation into the public sector requires long-run strategic investments and public policies to increase the supply and quality of human capital and infrastructure.The goal should be to narrow digital divide with other developed countries and advance the technological capabilities and productivity of the public service.

CMOS Direct-Injection Divide-by-3 Injection-Locked Frequency Dividers

This paper proposes CMOS LC-tank divide-by-3 injection locked frequency dividers(ILFDs)fabricated in 0.18μn and 90nm CMOS process and describes the circuit design,operation principle and measurement results of the ILFDs.The ILFDs use two injection series-MOSFETs across the LC resonator and a differential injection signal is applied to the gates of injection MOSFETs.The direct-injection divide-by-3 ILFDs are potential for radio-frequency application and can have wide locking range.

INJECTION-LOCKED DIVIDER

An injection-Locked divider(ILD)can provide good synchronization at lower inputsignal to noise ratio,which is its advantage over other types of divider.The general expressionof phase equation and equivalent model are presented for the ILD with an input additive noise.In the absence of noise the performance of the phase-modulated signal through the ILD andsynchronous ranges of the ILD are given.The effects of the additive noise on the ILD arediscuued.The injection-locked amplifier(ILA)is only a particular case in which n=1,thereforethe given results arc applicable to the ILA.

Residual Phase Noise and Time Jitters of Single-Chip Digital Frequency Dividers

In this paper, we demonstrate the residual phase noise of a few microwave frequency dividers which usually limit the performance of frequency synthesizers. In order to compare these dividers under different operation frequencies, we calculate additional time jitters of these dividers by using the measured phase noise. The time jitters are various from -0.1 fs to 43 fs in a bandwidth from 1 Hz to 100 Hz in dependent of models and operation frequencies. The HMC series frequency dividers exhibit outstanding performance for high operation frequencies, and the time jitters can be sub-fs. The time jitters of SP8401, MC10EP139, and MC100LVEL34 are comparable or even below that of HMC series for low operation frequencies.

A new type of Wilkinson dual-frequency power divider with symmetrical transmission line stubs

To realize equal power splitting at two arbitrary gigahertz-frequencies, this paper presents a new type of Wilkinson dual frequency power divider, consisting of three-section transmission lines and a series RLC(resistor, inductor and capacitor)circuit. By equating the [ABCD] matrix of the proposed circuit to that of the quarter-wave impedance transformer, coupled with even/odd mode analyses, the design equations of the proposed network are derived. For verification, two dual-frequency power dividers with dual-band operating frequencies at 0.6 GHz and 3.0 GHz, and 3.8 GHz and 10 GHz respectively are designed and simulated. Simulation results show that the dual-band ratio of the proposed power divider can be as large as 5. Comparisons of the simulation results at X-band and S-band with different power dividers indicate that the proposed dual-band power divider performs better under the scenario of the upper operating frequency extending to X-band.