The inhomogeneous sound speed in seawater causes refraction of sound waves,and the elimination of the refraction effect is essential to the accuracy of underwater acoustic positioning.The raytracing method is an indis...The inhomogeneous sound speed in seawater causes refraction of sound waves,and the elimination of the refraction effect is essential to the accuracy of underwater acoustic positioning.The raytracing method is an indispensable tool for effectively handling problems.However,this method has a conflict between localization accuracy and computational quantity.The equivalent sound speed profile(ESSP)method uses a simple sound speed profile(SSP)instead of the actual complex SSP,which can improve positioning precision but with residual error.The residual error is especially non-negligible in deep water and at large beam incidence angles.By analyzing the residual error of the ESSP method through a simulation,an empirical formula of error is presented.The data collected in the sailing circle mode(large incidence angle)of the South China Sea are used for verification.The experiments show that compared to the ESSP method,the improved algorithm has higher positioning precision and is more efficient than the ray-tracing method.展开更多
Based on the measured thermal cycle of double-wire submerged arc welding （SAW）, the gleeble thermal test was performed. Meanwhile, the Charpy V-notch impact test at -50 ℃ and hardness test at room temperature were ...Based on the measured thermal cycle of double-wire submerged arc welding （SAW）, the gleeble thermal test was performed. Meanwhile, the Charpy V-notch impact test at -50 ℃ and hardness test at room temperature were carried out after the thermal test. Thermally cycled microstructure and fracture surfaces were observed too. The results indicate that impact toughness of heat-affected zone （HAZ） at -50 ℃ is lower than that of parent metal with different wire spacing and welding speed. The microstracture of coarse-grains heat-affected zone （ CGHAZ ） is mainly made up of lath bainite with serious brittleness. The study also shows that a smaller energy input could be adopted to ensure the toughness of welded joints at the welding process in a common molten pool, while a higher energy input could be exerted to enhance welding efficieney at the welding process in two separate molten pools.展开更多
The contribution presents the representative research progress on global static gravity field modeling,regional geoid/quasigeoid determination,vertical datum study,as well as the theory,algorithm and software for grav...The contribution presents the representative research progress on global static gravity field modeling,regional geoid/quasigeoid determination,vertical datum study,as well as the theory,algorithm and software for gravity field study in China from 2019 to 2023,which are the highlights of the chapter 6“Progress in Earth Gravity Model and Vertical Datum”in the“2019—2023 China National Report on Geodesy”that submitted to the International Association of Geodesy(IAG).In addition,suggestions are proposed to promote the research in the fields of earth gravity field,geoid/quasigeoid and vertical datumin China according to trends of international geodesy and related disciplines.展开更多
Global uniform chart datum(CD)surface construction is the basic upon which to realize various vertical datums transformation,and is of great importance for geospatial data expression under the same vertical datum.Gene...Global uniform chart datum(CD)surface construction is the basic upon which to realize various vertical datums transformation,and is of great importance for geospatial data expression under the same vertical datum.Generally,the CD level is computed by developing the function between tidal constituents’harmonic constants and time,i.e.,the lowest astronomical tide is taken as the lowest predicted tide level by adopting the major constituents over a 19-a period.The CD surface prescribed in China is the theoretical lowest tide(TLT)and is calculated using 13 tidal constituents,i.e.,short-period(Q_(1),O_(1),P_(1),K_(1),N_(2),M_(2),S_(2),K_(2),M_(4),MS_(4)and M_(6))and long-period(Sa and Ssa)tidal constituents.Although the accuracy in determining short-period tidal constituents has improved gradually,the long-period tide has not been studied thoroughly owing to nonstationary and temporal variations.Previous studies have intended to evaluate the effect of Sa and Ssa tides in the determination of the TLT level for the purpose of determining a more accurate CD surface for the China seas and adjacent waters.Here,the parameters of long-period tidal correction and long-period tidal correction rate were treated as the effect of both Sa and Ssa on the TLT,and the TOPEX/Poseidon and Jason series satellite altimetry data ranged from October 1992 to April 2022 were adopted to analyze the contribution of long-period tidal constituents.Results showed that the average long-period correction value is 10.10 cm(range from 8.57 cm to 14.98 cm),and that the average long-period tidal contribution rate is 14.56%(range from 9.09%to 23.97%)in the China seas and adjacent waters.Finally,data from 82 tide gauge station with at least a 1-a record of hourly observations were compared with satellite-derived result.We concluded that the long-period tidal contribution should not be neglected in TLT construction.Furthermore,to reduce tidal datum uncertainty,accurate extraction of long-period tidal constituents should receive closer attentions.展开更多
This paper first develops the approaches to determine the geopotential of the local mean sea level,and then investigates the offset of the 1985 vertical datum surface defined by the mean sea level of Yellow Sea at the...This paper first develops the approaches to determine the geopotential of the local mean sea level,and then investigates the offset of the 1985 vertical datum surface defined by the mean sea level of Yellow Sea at the Dagang Tide Gauge in Qingdao city using the developed approaches and GPS/leveling data.It shows that the geopotential of the local mean sea level at the tide gauge is equal to 62 636 853.5±0.2 m2·s -2 and that the 1985 vertical datum surface is 24.6±5.4 cm above the geoid realized by the geopotential W 0= 62 636 856.0±0.5 m2·s -2.展开更多
基金the Natural Science Foundation of Shandong Province of China(No.ZR2022MA051)the China Postdoctoral Science Foundation(No.2020M670891)the SDUST Research Fund(No.2019TDJH103)。
文摘The inhomogeneous sound speed in seawater causes refraction of sound waves,and the elimination of the refraction effect is essential to the accuracy of underwater acoustic positioning.The raytracing method is an indispensable tool for effectively handling problems.However,this method has a conflict between localization accuracy and computational quantity.The equivalent sound speed profile(ESSP)method uses a simple sound speed profile(SSP)instead of the actual complex SSP,which can improve positioning precision but with residual error.The residual error is especially non-negligible in deep water and at large beam incidence angles.By analyzing the residual error of the ESSP method through a simulation,an empirical formula of error is presented.The data collected in the sailing circle mode(large incidence angle)of the South China Sea are used for verification.The experiments show that compared to the ESSP method,the improved algorithm has higher positioning precision and is more efficient than the ray-tracing method.
文摘Based on the measured thermal cycle of double-wire submerged arc welding （SAW）, the gleeble thermal test was performed. Meanwhile, the Charpy V-notch impact test at -50 ℃ and hardness test at room temperature were carried out after the thermal test. Thermally cycled microstructure and fracture surfaces were observed too. The results indicate that impact toughness of heat-affected zone （HAZ） at -50 ℃ is lower than that of parent metal with different wire spacing and welding speed. The microstracture of coarse-grains heat-affected zone （ CGHAZ ） is mainly made up of lath bainite with serious brittleness. The study also shows that a smaller energy input could be adopted to ensure the toughness of welded joints at the welding process in a common molten pool, while a higher energy input could be exerted to enhance welding efficieney at the welding process in two separate molten pools.
基金National Key R&D Program of China(Nos.2021YFB3900200,2021YFB3900203)。
文摘The contribution presents the representative research progress on global static gravity field modeling,regional geoid/quasigeoid determination,vertical datum study,as well as the theory,algorithm and software for gravity field study in China from 2019 to 2023,which are the highlights of the chapter 6“Progress in Earth Gravity Model and Vertical Datum”in the“2019—2023 China National Report on Geodesy”that submitted to the International Association of Geodesy(IAG).In addition,suggestions are proposed to promote the research in the fields of earth gravity field,geoid/quasigeoid and vertical datumin China according to trends of international geodesy and related disciplines.
基金The National Natural Science Foundation of China under contract No.42104035the Basic Scientific Fund for National Public Research Institutes of China under contract No.2023Q05the Natural Science Foundation of Shandong Province under contract No.ZR2020QD087.
文摘Global uniform chart datum(CD)surface construction is the basic upon which to realize various vertical datums transformation,and is of great importance for geospatial data expression under the same vertical datum.Generally,the CD level is computed by developing the function between tidal constituents’harmonic constants and time,i.e.,the lowest astronomical tide is taken as the lowest predicted tide level by adopting the major constituents over a 19-a period.The CD surface prescribed in China is the theoretical lowest tide(TLT)and is calculated using 13 tidal constituents,i.e.,short-period(Q_(1),O_(1),P_(1),K_(1),N_(2),M_(2),S_(2),K_(2),M_(4),MS_(4)and M_(6))and long-period(Sa and Ssa)tidal constituents.Although the accuracy in determining short-period tidal constituents has improved gradually,the long-period tide has not been studied thoroughly owing to nonstationary and temporal variations.Previous studies have intended to evaluate the effect of Sa and Ssa tides in the determination of the TLT level for the purpose of determining a more accurate CD surface for the China seas and adjacent waters.Here,the parameters of long-period tidal correction and long-period tidal correction rate were treated as the effect of both Sa and Ssa on the TLT,and the TOPEX/Poseidon and Jason series satellite altimetry data ranged from October 1992 to April 2022 were adopted to analyze the contribution of long-period tidal constituents.Results showed that the average long-period correction value is 10.10 cm(range from 8.57 cm to 14.98 cm),and that the average long-period tidal contribution rate is 14.56%(range from 9.09%to 23.97%)in the China seas and adjacent waters.Finally,data from 82 tide gauge station with at least a 1-a record of hourly observations were compared with satellite-derived result.We concluded that the long-period tidal contribution should not be neglected in TLT construction.Furthermore,to reduce tidal datum uncertainty,accurate extraction of long-period tidal constituents should receive closer attentions.
文摘This paper first develops the approaches to determine the geopotential of the local mean sea level,and then investigates the offset of the 1985 vertical datum surface defined by the mean sea level of Yellow Sea at the Dagang Tide Gauge in Qingdao city using the developed approaches and GPS/leveling data.It shows that the geopotential of the local mean sea level at the tide gauge is equal to 62 636 853.5±0.2 m2·s -2 and that the 1985 vertical datum surface is 24.6±5.4 cm above the geoid realized by the geopotential W 0= 62 636 856.0±0.5 m2·s -2.
