Synthesis of porous nano/micro structured LiFePO_4/C cathode materials for lithium-ion batteries by spray-drying method

In order to enhance electrochemical properties of LiFePO4 （LFP） cathode materials, spherical porous nano/micro structured LFP/C cathode materials were synthesized by spray drying, followed by calcination. The results show that the spherical precursors with the sizes of 0.5-5 μm can be completely converted to LFP/C when the calcination temperature is higher than 500 ℃. The LFP/C microspheres obtained at calcination temperature of 700 ℃ are composed of numerous particles with sizes of -20 nm, and have well-developed interconnected pore structure and large specific surface area of 28.77 mE/g. The specific discharge capacities of the LFP/C obtained at 700 ℃ are 162.43, 154.35 and 144.03 mA.h/g at 0.5C, 1C and 2C, respectively. Meanwhile, the capacity retentions can reach up to 100% after 50 cycles. The improved electrochemical properties of the materials are ascribed to a small Li＋ diffusion resistance and special structure of LFP/C microspheres.

Effects of Specimen Shape and Size on Water Loss and Drying Shrinkage of Cement-based Materials

The effects of specimen size and shape on development of water loss and shrinkage of mortar and concrete respectively were investigated. The experimental results showed that the effects of specimen size and shape on water loss ratio were consistent with those on drying shrinkage strain. It is also indicated that drying shrinkage strain has obvious linear correlation with water loss ratios independent of specimen size and shape. The effects of specimen size and shape on the water loss ratio were embodied in established model of averaged relative humidity improved by considering effects of sequential hydration and calculated by finite difference method. Furthermore, the effects of specimen size and shape on drying shrinkage strain of concrete were experimentally deduced and applied to modify criterion EB-FIP1990. The comparison between experimental and calculated results shows that the modified EB-FIP1990 can be adopted to predict drying shrinkage strain of concrete with reasonable accuracy.

Thermo-Physical Potential of Recycled Banana Fibers for Improving the Thermal and Mechanical Properties of Biosourced Gypsum-Based Materials

The development of bio-sourced materials is essential to ensuring sustainable construction;it is considered a locomotive of the green economy.Furthermore,it is an abundant material in our country,to which very little attention is being given.This work aims to valorize the waste of the trunks of banana trees to be used in construction.Firstly,the physicochemical properties of the fiber,such as the percentage of crystallization and its morphology,have been determined by X-ray diffraction tests and scanning electron microscopy to confirm the potential and the impact of the mode of drying on the quality of the banana fibers,with the purpose to promote the use of this material in construction.Secondly,the results obtained with the gypsum matrix allowed us to note a preponderant improvement in the composite’s thermal properties thanks to the variation of the banana fiber additive.Thirdly,the impact of the nature of the banana fiber distribution(either fiber mixed in matrix or fiber series model)on the flexural and compressive strengths of the composites was studied.The results obtained indicate that the insulation gain reaches up to 40%.It depends on the volume fraction and type of distribution of the banana fibers.However,the thermal inertia of the composites developed,represented by thermal diffusivity and thermal effusivity,was studied.Results indicate a gain of 40%and 25%,respectively,in terms of thermal diffusivity and thermal effusivity of the developed composites compared to plaster alone.Concerning the mechanical properties,the flexural strength depends on the percentage of the volume fraction of banana fibers used,and it can reach 20%more than the flexural strength of plaster;nevertheless,there is a significant loss in terms of the compressive strength of the studied composites.The results obtained are confirmed by the microstructure of the fiber banana.In fact,the morphology of the banana fibers was improved by the drying process.It reduces the amorphous area and improves the cellulosic crystalline surfaces,which assures good adhesion between the fiber and the matrix plaster.Finally,the dimensionless coefficient analysis was done to judge the optimal proportion of the banana fiber additive and to recommend its use even on false ceilings or walls.

Numerical investigation on freeze-drying of aqueous material frozen with pre-built pores

Freeze-drying of the initially porous frozen material with pre-built pores from liquid material was found experimentally to save drying time by over 30% with an initial saturation being 0.28 compared with the conventional operation with the initial saturation being 1, using mannitol as the solid material. In order to understand the mass and heat transfer phenomena of this novel process, a two-dimensional mathematical model of coupled mass and heat transfer was derived with reference to the cylindrical coordinate system. Three adsorption–desorption equilibrium relationships between the vapour pressure and saturation value namely, power-law, Redhead's style and Kelvin's style equation, were tested. Kelvin's style in exponential form of adsorption equilibrium relation gave an excellent agreement between the model prediction and experimental measurement when the equation parameter, γ, of 5000 was applied. Analyses of temperature and ice saturation profiles show that additional heat needs to be supplied to increase the sample temperature in order to promote the desorption process. Simulation also shows that there is a threshold initial porosity after which the drying time decreased with the increase in the initial porosity. Enhanced freeze-drying is expected to be achieved by simultaneously enhancing mass and heat transfer of the process.

Mathematical Model for the Drying Process of Granular Materials in a Fluidized Bed

The experiment of granular materials, barley, drying in a fluidized bed was carried out to investigate the influence of the factors, inlet air temperature, air moisture, bed height and original moisture content of the dried materials on drying process. Based on the experimental data, a corresponding mathematical model is presented. As a conclusion, a higher inlet air temperature and a reasonable bed height should be used so as to increase the dring rate and to improve the product quality.

Application of Fly Ash and Organic Material as Dry Cover System in Prevention of Acid Mine Drainage Generation

The common practice in AMD prevention is a dry cover technique. In this technique, rock that is potential in producing acidity (PAF) will be placed below non-acid producing rock (NAF). Depends on NAF availability in the mine site situation, organic covers can be used to prevent diffusion of oxygen into reactive sulphide wastes and subsequently to eliminate sulphide compounds oxidation and generation of acidic waters. The utilization of additional material cover layer is proposed, by using fly ash and organic material combination. To investigate the possibility of using these materials, a column leaching test in the laboratory scale was conducted with several scenarios of simulation. By comparing between column with different thickness of fly ash and organic material, the leachate water behavior is observed in the experiment, including the measurement of water quality (pH and EC), major cations-anions. The result suggests the possible thickness of fly ash (FA) and organic material (OM) as cover layer material, especially in the case of mine with domination of PAF rock material.

Corrosion Mechanism of Alumina-magnesia Dry Materials for Smelting Manganese/chromium Steel in Coreless Medium Frequency Induction Furnaces

Alumina-magnesia dry materials are widely used in induction furnace linings, but they show different kinds of damage when melting different kinds of alloy steel. In this paper, the chemical composition, phase composition, and microstructure of the post-use dry materials for the working liners melting different kinds of steel were evaluated. Furthermore, the corrosion mechanism of the steel on the furnace lining materials was comprehensively analyzed. The findings reveal a significant ability of the Mn element in the molten steel to diffuse and penetrate into the refractories. Mn oxidizes to form MnO at the steel-refractory interface, and then forms a liquid phase with Al_(2)O_(3). The Cr element is dissolved into corundum and spinel of the refractories, resulting in lattice defects and structural damage of the materials. TiO2reacts with Al_(2)O_(3) to form Al_(2)TiO_(5), which plays a crucial role in preventing crack formation and propagation. Part of Ti4+dissolves into magnesia-alumina(MA), densifying the materials. TiO2also slows down the reaction between the Cr element and refractory components, further improving the corrosion resistance of the materials.

Analysis of Raw Materials Components of Dry Composite Mixes for Production Food Concentrates

Background:The simplest and most convenient food technology is the using of dry composite mixtures.They have a lot of advantages.Dry composite mixtures,which would completely be the basis for the production of personalized food concentrates,are not represented.The development of such dry composite mixtures is actual and of scientific and practical interest.The purpose of this research is the selection and justification of local import-substituting raw materials components for dry composite mixtures used as the basis for the production of food concentrates.As the objects of research,the raw materials components of the starch,fruit and vegetable,industry were selected.The work uses currently accepted standard research methods for organoleptic and physic-chemical parameters of raw materials components.The research was carried out within of the project“Theoretical Substantiation of Production Technology and the Development of Import-Substituting Food Products of Functional Purpose Based on Dry Composite Mixtures”,funded by the Belarusian Republican Foundation for Basic Research.Based on the researches,it was found out that in the composition of dry composite mixtures for the production of food concentrates it is expedient to use the following raw materials:potato starch,extruded corn starch,dried carrots,dried beets,dried topinambur and dried apples in chopped form.

3D Model Simulating the Hydro-mechanical State of Unsaturated and Deformable Material during Hot air Drying

A three dimensional model to predict the hydro-mechanical state of unsaturated and deformable material during hot air drying has been proposed.The material viscoelastic behaviour was formulated using Bishop’s effective stress theory for partially saturated material using the liquid saturation as the Bishop parameter.The hydro-thermal and mechanical equations were coupled by the fluid pressure and the solid matter velocity.The model was applied to a deformable material(innovative clay-cellulose fibers composite)subjected to convective drying.A generalized Maxwell model with five elements,whose parameters were measured experimentally and correlated to water content was used to describe the material’s viscoelastic behavior.The hydro-thermal part of the proposed model was validated on the basis of a comparison of experimental and simulated drying rate curves.The Von Mises stress was simulated and compared to the experimental tensile strength in order to predict the time and the region of material failure.For a drying process at 95°C,the region of failure risk was identified.The failure may occur on the lateral surface of the slab in contact with air at a drying time of 2.5h.

Etching‐assisted femtosecond laser modification of hard materials

With high hardness, high thermal and chemical stability and excellent optical performance, hard materials exhibit great potential applications in various fields, especially in harsh conditions. Femtosecond laser ablation has the capability to fabricate three-dimensional micro/nanostructures in hard materials. However, the low efficiency, low precision and high surface roughness are the main stumbling blocks for femtosecond laser processing of hard materials. So far, etching- assisted femtosecond laser modification has demonstrated to be the efficient strategy to solve the above problems when processing hard materials, including wet etching and dry etching. In this review, femtosecond laser modification that would influence the etching selectivity is introduced. The fundamental and recent applications of the two kinds of etching assisted femtosecond laser modification technologies are summarized. In addition, the challenges and application prospects of these technologies are discussed.

On the hydro-mechanical behaviour of MX80 bentonite-based materials

Bentonite-based materials have been considered in many countries as engineered barrier/backfilling materials in deep geological disposal of high-level radioactive waste.During the long period of waste storage,these materials will play an essential role in ensuring the integrity of the storage system that consists of the waste canisters,the engineered barrier/backfill,the retaining structures as well as the geological barrier.Thus,it is essential to well understand the hydro-mechanical behaviours of these bentonite-based materials.This review paper presents the recent advances of knowledge on MX80 bentonite-based materials,in terms of water retention properties,hydraulic behaviour and mechanical behaviour.Emphasis is put on the effect of technological voids and the role of the dry density of bentonite.The swelling anisotropy is also discussed based on the results from swelling tests with measurements of both axial and radial swelling pressures on a sand-bentonite mixture compacted at different densities.Microstructure observation was used to help the interpretation of macroscopic hydromechanical behaviour.Also,the evolution of soil microstructure thus the soil density over time is discussed based on the results from mock-up tests.This evolution is essential for understanding the longterm hydro-mechanical behaviour of the engineered barrier/backfill.

Amorphous Zr(OH)4 coated LiNi0.915Co0.075Al0.01O2 cathode material with enhanced electrochemical performance for lithium ion batteries

LiNiCoAlO（NCA） with Zr（OH）coating is demonstrated as high performance cathode material for lithium ion batteries（LIBs）. The coated materials are synthesized via a simple dry coating method of NCA with Zr（OH）powders, and then characterized with scanning electron microscopy（SEM）, transmission electron microscopy（TEM） and X-ray photoelectron spectroscopy（XPS）. Experimental results show that amorphous Zr（OH）powders have been successfully coated on the surface of spherical NCA particles, exhibiting improved electrochemical performance. 0.50 wt% Zr（OH）coated NCA delivers a capacity of 197.6 mAh/g at the first cycle and 154.3 mAh/g after 100 cycles with a capacity retention of 78.1% at 1 C rate. In comparison, the pure NCA shows a capacity of 194.6 mAh/g at the first cycle and 142.5 mAh/g after 100 cycles with a capacity retention of 73.2% at 1 C rate. Electrochemical impedance spectroscopy（EIS） results show that the coated material exhibits a lower resistance, indicating that the coating layer can efficiently suppress transition metals dissolution and decrease the side reactions at the surface between the electrode and electrolyte. Therefore, surface coating with amorphous Zr（OH）is a simple and useful method to enhance the electrochemical performance of NCA-based materials for the cathode of LIBs.

Structure and Properties of Porous Silk Fibroin Materials

In this article the structure and properties of freeze-dried porous silk fibroin materials were tested and analyzed.The results indicated that for porous silk fibroin materials prepared by means of freeze-drying,if freez-ing temperature was below —20℃,the structure of silk fibroin was mainly amorphous with a little silk Ⅱ crystal structure,and if freezing temperature was above —20℃,quite a lot of silk Ⅰ crystal structure formed.Porous silk fibroin materials,with average pore diameter be-

Biogenic Amines Profile of Serbian Traditional Sausage in Relation to Raw Material and Production Conditions

Petrovska klobasa is a traditional dry fermented sausage produced in the Autonomous Province of Vojvodina. Formation of nine hiogenic amines was determined in three sausage groups produced from hot deboned （A1） and cold meat （B1, B3） during drying and ripening in traditional room （A1, B1） and in industrial ripening chamber （B3）. Dansyl chloride derived amines were analysed by high-performance liquid chromatography with diode-array detector （HPLC-DAD） on Eclipse XDB-C18 column. Histamine, the most important amine from food safety point of view, was not found in any of the analyzed samples. Serotonin and spermidine were also not detected in any samples, while spermin was determined in all analyzed samples. At the end of drying, phenylethylamine was the predominant amine in A1 sausage group （51.6 mg/kg）, and tryptamine in B1 （38.1 mg/kg） and B3 （28.7 mg/kg） sausage groups. At the end of ripening, tryptamine was the predominant biogenic amine in all sausage groups （133, 121 and 39.8 mg/kg in A1, B1 and B3 groups, respectively）. Total level of biogenic amines in all investigated sausages did not exceed 174 mg/kg at the end of drying and 238 mg/kg at the end of ripening period. Tryptamine and cadaverine may be used as indicators of total biogenic amines for sausages produced in traditional and indusrial conditions from hot deboned and cold meat.

A Novel Method of Fruit Raw Material Reprocessing

We introduced a method of deep resources-economy reprocessing of fruit raw material. Based on the raw material fractionation at decreased temperatures the method results in the production of bioactive food stuffs, which are dry juice and refuse and natural water. The method includes the production of directly extracted juice and pulp refuse, juice evaporation in vacuum with the production of concentrate and natural water, and air drying the concentrate and the refuse. The method is realized for garden strawberry and cucurbit pulp. The mass concentration of solid in the fractions of cucurbit pulp is defined and the specific weight of the fractions are defined. It is shown that the solid of the cucurbit pulp is uniformly allocated between the fractions and amounts 34% for the dry juice, 31% for the dry refuse, and 35% for the natural water. Food and biological values of the cucurbit pulp fractions are determined. It is determined that the cucurbit includes silicium, nickel, and chromium. Silicium is contained only in dry fractions;nickel is present everywhere;chromium is discovered only in the natural water. Food and biological values of the cucurbit pulp are defined and their allocation between the fractions is determined. Separate components concentrations of the solid considerably differ between the fractions. Thus, two thirds of pulp protein is concentrated in the dry juice and a third is concentrated in the refuse. The natural water contains up to 90% of fat and sugar, from a half to two thirds of B-group vitamins, and the bulk of the mineral substances (K, Na, Ca, Mg, S, Co, Cu, Ni, Cr, and Zn), which concentration composes from 73% for potassium up to 100% for chromium.

Soil Improvement Using Waste Materials:A Review

With the industrialisation,industrial byproducts are produced in large quantities and create nuisance to natural habitats.The disposal of these wastes like fly ash,marble powder,construction and demolition(C&D)waste,brick powder,agricultural wastes etc.has become the potential threat to the ecosystem and need some real solutions.The direct disposal of such wastes into open land or water bodies causes circumambient pollution.One of the potential solutions is to utilise these wastes in the construction industry on large scale as subgrade rehab or additive to cement based materials.In the present study,the compaction and strength characteristics of stabilised soil have been studied by using various waste materials i.e.lime,cement,plastic waste,industrial waste,fibre,mushroom waste,wet olive pomace etc.and reviewed.The addition of additives improved the engineering properties of soil significantly.

Preparation of high emissivity NiCr_2O_4 powders with a spinel structure by spray drying

Spray-drying was used to produce the high emissivity NiCr2O4 powders with a spinel structure. Preliminary investigations focused on fabricating the high emissivity powders for infrared radiation coatings and finding the relationship between microstructure and emissivity. The NiCr2O4 powders were characterized for composition, microstructure, and infrared emissivity by X-ray diffraction （XRD）, scanning electron microscopy （SEM）, infrared radiant instrument, and Fourier transform infrared spectra （FT-IR）. Thermogravimetry and differential thermal analysis show that the appropriate baking temperature for NiCr2O4 powder preparation is about 1200？C. The emissivity measurement and FT-IR spectra show that, because of the special spinel structure, the NiCr2O4 powders have a high emissivity about 0.91. Spray-drying is a suitable method to produce the high emissivity ceramic powders.

Microstructure and dry wear properties of Ti-Nb alloys for dental prostheses

The microstructure and properties of a series of binary Ti-Nb alloys for dental prostheses with niobium contents ranging from 5% to 20% were investigated. The experimental results indicate that the crystal structure and morphology of Ti-Nb alloys are sensitive to their niobium contents. When Nb content is 5%, the acicular α crystal grain is observed. When Nb content is 10%, the coarse equiaxed crystal grain and the fine, acicular α crystal grain are observed. When Nb content is 15%, only the α equiaxed crystal grain is observed. When the alloy contains 20%Nb, the equiaxed and dendritic α crystal grain are observed. For Ti-Nb alloys, the increase of Nb content modifies the microstructure of Ti-Nb alloys significantly and decreases their compression elastic modulus, in which Ti-20Nb alloy shows the largest compression strength and Ti-5Nb alloy shows the best plasticity. The dry wear resistance of Ti-Nb alloys against Gr15 ball was investigated on CJS111A ball-disk wear instrument. For Ti-Nb alloys, Ti-10Nb alloy shows a smallest steady friction coefficient, Ti-5Nb alloy shows the smallest wear depth and best wear resistance, and Ti-15Nb alloy shows the largest wear depth and worst wear resistance. The phenomenon of furrow cut happens and furrows form during wear tests.

A comparative study of drying techniques on the morphology of porous silica gels synthesized via sol-gel process

The effect of drying techniques on the microstructure,morphology and pore structure of porous silica gels was studied in the paper.The gels were prepared by using sol-gel process and different drying routes:freeze-drying (FD),low pressure drying (LPD),high temperature drying (HTD) and chemical modification & ambient drying (CMD) techniques.Observation under pore distribution and structural properties showed that CMD technique leads to homogenous mesoporous silica material with specific surface area of 745 m2/g,and the average pore size around 20 nm,while LPD and HTD result in loosely packed particles with non-isotropic aggregation pattern.The specific surface areas of LPD and HTD samples are 419 and 513 m2/g respectively,and the pore size distribution of the samples are observed distributing widely in range of 10-100 nm.Freeze drying method is a new but prospective way to prepare mesoporous silica.The specific area of FD sample is around 500 m2/g.By the comparison for the properties of the gels,this paper wants to induce a further interest in finding a proper method to synthesize the porous silica gels for low price use.

Temperature and Humidity Control System Identification Based on Neural Network in Heating and Drying System

Artificial neural network has unique advantages for massively parallel processing, distributed storage capacity and self-learning ability. The paper mainly constructs neural network identifier and neural network controller for system identification and control on temperature and hmnidity of heating and drying system of materials. And the paper introduces the structure and principles of neural network, and focuses on analyzing learning algorithm, training algorithm and limitation of the most widely applied multi-layer feed-forward neural network （ BP network） , based on which the paper proposes introducing momentum to improve BP network.