Discussion on the application prospect of the transient electromagnetic method based on the dual launcher and mine advanced detection

The dual transmitter implements the equivalent anti-magnetic flux transient electromagnetic method, which can effectively reduce the scope of the transient electromagnetic detection blind area. However, this method is rarely reported in the detection of pipelines in urban geophysical exploration and the application of coal mines. Based on this, this paper realizes the equivalent anti-magnetic flux transient electromagnetic method based on the dual launcher. The suppression effect of this method on the blind area is analyzed by physical simulation. And the detection experiment of underground pipelines is carried out outdoors. The results show that the dual launcher can significantly reduce the turn-off time, thereby effectively reducing the impact of the blind area on the detection results, and the pipeline detection results verify the device’s effectiveness. Finally, based on the ground experimental results, the application prospect of mine advanced detection is discussed. Compared with other detection fields, the formation of blind areas is mainly caused by the equipment. If the dual launcher can be used to reduce the blind area, the accuracy of advanced detection can be improved more effectively. The above research results are of great significance for improving the detection accuracy of the underground transient electromagnetic method.

Scattering of Water Waves by Dual Symmetric Inclined Floating Porous Barriers Using the DBEM

The scattering of normally incident water waves by two surface-piercing inclined perforated barriers in water with a uniform finite depth is investigated within the framework of linear water wave theory.Considering that thin barriers are zero-thickness,a novel numerical method involving the the coupling of the dual boundary element method(DBEM)with damping layers is applied.In order to effectively damp out the reflected waves,two damping layers,instead of pseudoboundaries are implemented near the two side boundaries of the computational domain.Thus,the modified linearized free surface boundary conditions are formulated and used for solving both the ordinary boundary integral equation as well as the hypersingular boundary integral equation for degenerate boundaries.The newly developed numerical method is validated against analytical methods using the matched eigenfunction expansion method for the special case of two vertical barriers or the inclined angle to the vertical being zero.The influence of the length of the two damping layers has been discussed.Moreover,these findings are also validated against previous results for several cases.After validation,the numerical results for the reflection coefficient,transmission coefficient and dissipation coefficient are obtained by varying the inclination angle and porosity-effect parameter.The effects of both the inclination angle and the porosity on the amplitudes of wave forces acting on both the front and rear barriers are also investigated.It is found that the effect of the inclination angle mainly shifts the location of the extremal values of the reflection and the transmission coefficients.Additionally,a moderate value of the porosity-parameter is quite effective at dissipating wave energy and mitigating the wave loads on dual barriers.

Properties of SiC Particulate Preforms Based on Different Pore-forming Agents and Bonding Methods for Making SiC/Al Composites

The preforms with high SiC volume fraction （〉50%） were successfully fabricated by two bonding methods. Moreover, the dimensional change, compressive strength, and microstructure of SiC preforms were investigated, and the bonding mechanism among SiC particulates in preforms was also discussed. Results show that, after heating to 1 100 ~C and holding for 2 h, a uniform and interconnected structure in the SiC preforms can be obtained by using starch, stearic acid, and graphite respectively as the pore-forming agents, which benefits the subsequent infiltration by the molten metals. More neck-like-jointing among SiC particulate by using graphite as the pore-forming agent improves the dimensional accuracy and compressive strength of the preform. Besides, the properties of the preforms by the binder bonding are better than those by the oxidation bonding, which is mainly because the mixed neck-like-jointing and binder at high temperature provide effective bonding together.

Integrated interpretation of dual frequency induced polarization measurement based on wavelet analysis and metal factor methods

In mineral exploration, the apparent resistivity and apparent frequency （or apparent polarizability） parameters of induced polarization method are commonly utilized to describe the induced polarization anomaly. When the target geology structure is significantly complicated, these parameters would fail to reflect the nature of the anomaly source, and wrong conclusions may be obtained. A wavelet approach and a metal factor method were used to comprehensively interpret the induced polarization anomaly of complex geologic bodies in the Adi Bladia mine. Db5 wavelet basis was used to conduct two-scale decomposition and reconstruction, which effectively suppress the noise interference of greenschist facies regional metamorphism and magma intrusion, making energy concentrated and boundary problem unobservable. On the basis of that, the ore-induced anomaly was effectively extracted by the metal factor method.

New exact solutions for free vibrations of rectangular thin plates by symplectic dual method

The separation of variables is employed to solve Hamiltonian dual form of eigenvalue problem for transverse free vibrations of thin plates, and formulation of the natural mode in closed form is performed. The closed-form natural mode satisfies the governing equation of the eigenvalue problem of thin plate exactly and is applicable for any types of boundary conditions. With all combinations of simplysupported （S） and clamped （C） boundary conditions applied to the natural mode, the mode shapes are obtained uniquely and two eigenvalue equations are derived with respect to two spatial coordinates, with the aid of which the normal modes and frequencies are solved exactly. It was believed that the exact eigensolutions for cases SSCC, SCCC and CCCC were unable to be obtained, however, they are successfully found in this paper. Comparisons between the present results and the FEM results validate the present exact solutions, which can thus be taken as the benchmark for verifying different approximate approaches.

Abnormal variation of magnetic properties with Ce content in(PrNdCe)_2Fe_(14)B sintered magnets prepared by dual alloy method

Resource-saving（PrNdCe）_2Fe_（14）B sintered magnets with nominal composition（PrNd）_（15-x）Ce_xFe_（77）B_8（x=0–10）were prepared using a dual alloy method by mixing（PrNd）_5Ce_（10）Fe_（77）B_8 with（PrNd）_（15）Fe_（77）B_8 powders. For Ce atomic percent of 1% and 2%, coercivity decreases dramatically. With further increase of Ce atomic percent, the coercivity increases, peaks at 6.38 kOe in（PrNd）_（11）Ce_4Fe_（77）B_8, and then declines gradually. The abnormal dependence of coercivity is likely related to the inhomogeneity of rare earth chemical composition in the intergranular phase, where Pr Nd concentration is strongly dependent on the additive amount of（PrNd）_5Ce_（10）Fe_（77）B_8 powders. In addition, for Ce atomic percent of 8%,7%, and 6% the coercivity is higher than that of magnets prepared by the conventional method, which shows the advantage of the dual alloy method in preparing high abundant rare earth magnets.

DUAL RECIPROCITY HYBRID BOUNDARY NODE METHOD FOR THREE-DIMENSIONAL ELASTICITY WITH BODY FORCE

Combining Dual Reciprocity Method （DRM） with Hybrid Boundary Node Method （HBNM）, the Dual Reciprocity Hybrid Boundary Node Method （DRHBNM） is developed for three-dimensional linear elasticity problems with body force. This method can be used to solve the elasticity problems with body force without domain integral, which is inevitable by HBNM. To demonstrate the versatility and the fast convergence of this method, some numerical examples of 3-D elasticity problems with body forces are examined. The computational results show that the present method is effective and can be widely applied in solving practical engineering problems.

Infinitesimal dividing modeling method for dual suppliers inventory model with random lead times

As one of the basic inventory cost models, the （Q, τ）inventory cost model of dual suppliers with random procurement lead time is mostly formulated by using the concepts of ＂effective lead time＂ and ＂lead time demand＂, which may lead to an imprecise inventory cost. Through the real-time statistic of the inventory quantities, this paper considers the precise （Q, τ） inventory cost model of dual supplier procurement by using an infinitesimal dividing method. The traditional modeling method of the inventory cost for dual supplier procurement includes complex procedures. To reduce the complexity effectively, the presented method investigates the statistics properties in real-time of the inventory quantities with the application of the infinitesimal dividing method. It is proved that the optimal holding and shortage costs of dual supplier procurement are less than those of single supplier procurement respectively. With the assumption that both suppliers have the same distribution of lead times, the convexity of the cost function per unit time is proved. So the optimal solution can be easily obtained by applying the classical convex optimization methods. The numerical examples are given to verify the main conclusions.

Multiple Suppression Using T-A Dual Polynomial Fitting Method

Principles of polynomial fitting zero offset profile are introduced, and a new polynomial fitting method, tbe time-amplitude dual fitting method, is developed. The method can be used to purify seismic waves and suppress multiples. The effect of suppressing multiples is compared with other multiple suppression methods.

Application of dual reciprocity boundary element method to predict acoustic attenuation characteristics of marine engine exhaust silencers

In marine engine exhaust silencing systems, the presence of exhaust gas flow influences the sound propagation inside the systems and the acoustic attenuation performance of silencers. In order to investigate the effects of three-dimensional gas flow and acoustic damping on the acoustic attenuation characteristics of marine engine exhaust silencers, a dual reciprocity boundary element method (DRBEM) was developed. The acoustic governing equation in three-dimensional potential flow was derived first, and then the DRBEM numerical procedure is given. Compared to the conventional boundary element method (CBEM), the DRBEM considers the second order terms of flow Mach number in the acoustic governing equation, so it is suitable for the cases with higher Mach number subsonic flow. For complex exhaust silencers, it is difficult to apply the single-domain boundary element method, so a substructure approach based on the dual reciprocity boundary element method is presented. The experiments for measuring transmission loss of silencers are conducted, and the experimental setup and measurements are explained. The transmission loss of a single expansion chamber silencer with extended inlet and outlet were predicted by DRBEM and compared with the measurements. The good agreements between predictions and measurements are observed, which demonstrated that the derived acoustic governing equation and the DRBEM numerical procedure in the present study are correct.

Dual threshold search method for asperity boundary determination based on geodetic and seismic catalog data

As an important model for explaining the seismic rupture mode,the asperity model plays an important role in studying the stress accumulation of faults and the location of earthquake initiation.Taking Qilian-Haiyuan fault as an example,this paper combines geodetic method and b-value method to propose a multi-source observation data fusion detection method that accurately determines the asperity boundary named dual threshold search method.The method is based on the criterion that the b-value asperity boundary should be most consistent with the slip deficit rate asperity boundary.Then the optimal threshold combination of slip deficit rate and b-value is obtained through threshold search,which can be used to determine the boundary of the asperity.Based on this method,the study finds that there are four potential asperities on the Qilian-Haiyuan fault:two asperities(A1 and A2)are on the Tuolaishan segment and the other two asperities(B and C)are on Lenglongling segment and Jinqianghe segment,respectively.Among them,the lengths of asperities A1 and A2 on Tuolaishan segment are 17.0 km and 64.8 km,respectively.And the lower boundaries are 5.5 km and 15.5 km,respectively;The length of asperity B on Lenglongling segment is 70.7 km,and the lower boundary is 10.2 km.The length of asperity C on Jinqianghe segment is 42.3 km,and the lower boundary is 8.3 km.

Study on Monoxide Emission Spectrometry of Rare Earth Elements Ⅰ. Determination of Sm in Rare Earth Concentrate by Dual Wavelength Method

On the basis of investigated enhancement effect of La, Nd, Eu, and Y on Sm determination with monoxide molecular emission spectrometry, La was selected as enhancement agent and chemical interference inhibitor. In the presence of La, dual wavelength mothod was introduced to eliminate the spectral interference on Sm by other elements. A new method was established to determine samarium in high yttrium rare earth samples with satisfactory results.

Magnetic properties of misch-metal partially substituted Nd–Fe–B magnets sintered by dual alloy method

The misch-metal （MM） partially substituted Nd-Fe-B sintered magnets were fabricated by the dual alloy method, and the crystal structure, microstructure, and magnetic properties were analyzed comprehensively. X-ray diffraction （XRD） reveals that the increasing content of the MM has an inconsiderable effect on the crystallographic alignment of the magnets. Grains of the two main phases are uniformly distributed, and slightly deteriorate on the grain boundary. Due to the diffusion between the adjacent grains, the MM substituted Nd-Fe-B magnets contain three types of components with different Ce/La concentrations. Moreover, the first-order reversal curve （FORC） diagram is introduced to analyze the magnetization reversal process, coercivity mechanism, and distribution of reversal field in magnetic samples. The analysis indicates that there are two major reversal components, corresponding to the two different main phases. The domain nucleation and growth are determined to be the leading mechanism in controlling the magnetization reversal processes of the magnets sintered by the dual alloy method.

APPLICATION OF THE DUAL RECIPROCITY BOUNDARY ELEMENT METHOD TO SOLUTION OF NONLINEAR DIFFERENTIAL EQUATION

In this paper the dual reciprocity boundary element method is employed to solve nonlinear differential equation del(2) u + u + epsilon u(3) = b. Results obtained in an example have a good agreement with those by FEM and show the applicability and simplicity of dual reciprocity method (DRM) in solving nonlinear differential equations.

融合时间序列趋势的Dual-ESN机组负荷预测模型

针对传统模型在机组负荷预测中无法充分捕获内部多变量演化模式的问题,提出了一种基于时间序列的趋势和数值信息融合的双重回声状态网络Dual-ESN(dual-echo state network)机组负荷动态预测模型。首先,引入最小二乘法,对相关的多元历史信息按照局部时间跨度进行趋势拟合。进一步,得到有关过程变化的模式序列,并和原本的数值分别被送入两个独立的储备池,以并行的时间维度进行特征学习。其次,将隐层的高维空间状态送入输出层,融合信息,得到所需要的预测结果。最后,基于山西某工厂660 MW机组装置的真实数据集,进行验证。对比已有预测方法,结果表明所提预测模型在多种性能指标上均有提升。

A Novel Localized Meshless Method for Solving Transient Heat Conduction Problems in Complicated Domains

This paper first attempts to solve the transient heat conduction problem by combining the recently proposed local knot method(LKM)with the dual reciprocity method(DRM).Firstly,the temporal derivative is discretized by a finite difference scheme,and thus the governing equation of transient heat transfer is transformed into a non-homogeneous modified Helmholtz equation.Secondly,the solution of the non-homogeneous modified Helmholtz equation is decomposed into a particular solution and a homogeneous solution.And then,the DRM and LKM are used to solve the particular solution of the non-homogeneous equation and the homogeneous solution of the modified Helmholtz equation,respectively.The LKM is a recently proposed local radial basis function collocationmethod with themerits of being simple,accurate,and free ofmesh and integration.Compared with the traditional domain-type and boundary-type schemes,the present coupling algorithm could be treated as a really good alternative for the analysis of transient heat conduction on high-dimensional and complicated domains.Numerical experiments,including two-and three-dimensional heat transfer models,demonstrated the effectiveness and accuracy of the new methodology.

Simultaneous Determination of Uranium and Thorium with Standard Dual-addition Method

dual-standard addition method was proposed and the principle of simultaneous determination for a interfering binary mixtures was discussed. The proposed procedure was applied to spectroscopic analyses for the simultaneous determination of uranium and thorium without prior separation. Various molar ratios of uranium/thorium, from 0.5∶1 to 10∶1, can be determined with satisfactory precision and accuracy. Uranium and thorium content in a phosphate ore and simulated sample were determined, the recoveries were 98.4%～102.5% for uranium and 96.8%～102.3% for thorium, the relative standard deviations (R.S.D) were 1.5%～2.3% for uranium and 2.1%～3.1% for thorium.

Weighted Variational Minimization Model for Wavelet Domain Inpainting with Primal-Dual Method

To preserve the edges and details of the image,a new variational model for wavelet domain inpainting was proposed which contained a non-convex regularizer. The non-convex regularizer can utilize the local information of image and perform better than those usual convex ones. In addition, to solve the non-convex minimization problem,an iterative reweighted method and a primaldual method were designed. The numerical experiments show that the new model not only gets better visual effects but also obtains higher signal to noise ratio than the recent method.

Determination of Composition and Stability Constant of Praseodymium(Pr^(3+))Complex with Tribromoarsenazo(TBA)by Dual-Series Linear Regression Method

A new method,dual-series linear regression method,has been used to study the complexation equilibrium of praseodymium(Pr^(3+))with tribromoarsenazo(TBA)without knowing the accurate concentra- tion of the complexing agent TBA.In 1.2 mol/L HCl solution, Pr^(3+)reacts with TBA and forms 1:3 com- plex,the conditional stability constant(lgβ_3)of the complex determined is 15.47,and its molar absorptivity(ε_3^(630))is 1.48×10~5 L·mol^(-1)·cm^(-1).

Free-Interface Dual-Compatibility Modal Synthesis Substructure Method in Large-Scale Structures

Free-interface dual-compatibility modal synthesis method(compatibility of both force and displacement on interfaces)is introduced to large-scale civil engineering structure to enhance computation efficiency. The basic equations of the method are first set up, and then the mode cut-off principle and the dividing principle are proposed. MATLAB is used for simulation in different frame structures. The simulation results demonstrate the applicability of this substructure method to civil engineering structures and the correctness of the proposed mode cut-off principle. Studies are also conducted on how to divide the whole structure for better computation efficiency while maintaining better precision. It is observed that the geometry and material properties should be considered, and the synthesis results would be more precise when the inflection points of the mode shapes are taken into consideration. Furthermore, the simulation performed on a large-scale high-rise connected structure further proves the feasibility and efficiency of this modal synthesis method compared with the traditional global method. It is also concluded from the simulation results that the fewer number of DOFs in each substructure will result in better computation efficiency, but too many substructures will be time-consuming due to the tedious synthesis procedures. Moreover, the substructures with free interface will introduce errors and reduce the precision dramatically, which should be avoided.