Analysis of Rectangular Notch Antenna for Dual-Band Operation

In this paper a design of single layer rectangular notch microstrip antenna for dual-band is proposed and experimentally investigated. This antenna is excited by microstrip line. Direct microstrip coupling with proper matching transformer has been used. Design is made for optimized notch dimension for two resonant frequencies. These resonance frequencies change with the variation in length and width of the notch. The input impedance and VSWR have been measured with the help of Network analyzer. It is found that the input impedance and VSWR depends variation in length and width of the notch microstrip antenna.

Dual-band multi-beam reconfigurable terahertz antenna based on graphene frequency selective surface

In this paper,a dual-band graphene-based frequency selective surface(GFSS)is investigated and the operating mechanism of this GFSS is analyzed.By adjusting the bias voltage to control the graphene chemical po-tential between 0 eV and 0.5 eV,the GFSS can achieve four working states:dual-band passband,high-pass lowimpedance,low-pass high-impedance,and band-stop.Based on this GFSS,a hexagonal radome on a broadband omnidirectional monopole antenna is proposed,which can achieve independent 360°six-beam omnidirectional scanning at 1.08 THz and 1.58 THz dual bands.In addition,while increasing the directionality,the peak gains of the dual bands reach 7.44 dBi and 6.67 dBi,respectively.This work provides a simple method for realizing multi-band terahertz multi-beam reconfigurable antennas.

An Analysis of Mutual Interference in Radar Systems Using Dual-Band (Ka / X) Antennas

An analysis of mutual interfering sources on RF systems using dual-band (Ka / X) radar is presented. The purpose of this paper is to improve operational performance of the system from the point of view of EMC design. The experimental dual-band antenna system have decreased the disturbing effects of most mutual interfering sources.

Compact ultra-wideband monopole antenna with dual-band notched function

A kind of compact ultra wideband （UWB） monopole antenna with dual-band notched function is presented.The proposed antenna,using ＂C＂ and ＂L＂ apertures embedded in the annular ring patch and ground patch,gets two bandnotched characteristics in WiMAX3.5 GHz and WLAN 5.5 GHz.The size of antenna is 24 mm × 36 mm × 1.6 mm.The simulation results show that waveband range of the antenna is 2.7-10.6 GHz for S11 ＜-10 dB and the band-notched wavebands are 3.2-3.8 GHz and 5.1-6 GHz.So it has miniaturization,ultra-band and band-notched characteristics.Meanwhile,the radition pattern,directivety and gain are perfect,which meets the practical need.

Novel dual-band antenna for multi-mode GNSS applications

A novel dual-band antenna is proposed for mitigating the multi-path interference in the global navigation satellite system（GNSS） applications. The radiation patches consist of a shortedannular-ring reduced-surface-wave（SAR-RSW） element and an inverted-shorted-annular-ring reduced-surface-wave（ISAR-RSW）element. One key feature of the design is the proximity-coupled probe feeds to increase impedance bandwidth. The other is the defected ground structure band rejection filters to suppress the interaction effect between the SAR-RSW and the ISAR-RSW elements. In addition, trans-directional couplers are used to obtain tight coupling. Measurement results indicate that the antenna has a larger than 10 d B return loss bandwidth and a less than 3 d B axial-ratio（AR） bandwidth in the range of（1.164 – 1.255） GHz and（1.552 – 1.610） GHz. The gain of the passive antenna in the whole operating band is more than 7 d Bi.

RECONFIGURABLE DUAL-BAND CIRCULARLY POLARIZED MICROSTRIP PATCH ANTENNA FOR WIRELESS APPLICATIONS

A new design of reconfigurable single-feed circular patch microstrip antenna for dual-band circular polarization application is proposed. The dual-band functionality is realized through incorporating cross-slots of equal slot length in the circular patch and utilizing two PIN diodes to switch the slots on or off. A pairs of tuning stubs are used to tune the circular polarization performance. The design process is presented and good results were obtained.

Printed elliptical slot UWB antenna for dual-banded application

Based on the analysis of printed elliptical slot (PES) UWB antenna,a dual-banded PES antenna is designed for WLAN and UWB bands at 2.4 GHz.The design cooperates two important wireless commutation system antennas into one printed antenna.In the design,a circular slot structure is presented,which is suitable for the band ejection.Characteristics of the designed antenna are analyzed and key parameters,such as S11,S21 and VSWR are measured.E-field distribution of the surface is simulated and analyzed.

Computer Modelling of Compact 28/38 GHz Dual-Band Antenna for Millimeter-Wave 5G Applications

A four-element compact dual-band patch antenna having a common ground plane operating at 28/38 GHz is proposed formillimeter-wave communication systems in this paper.Themultiple-input-multiple-output(MIMO)antenna geometry consists of a slotted ellipse enclosed within a hollow circle which is orthogonally rotated with a connected partial ground at the back.The overall size of the four elements MIMO antenna is 2.24λ×2.24λ(at 27.12GHz).The prototype of four-element MIMOresonator is designed and printed using Rogers RTDuroid 5880 withε_(r)=2.2 and loss tangent=0.0009 and having a thickness of 0.8 mm.It covers dual-band having a fractional bandwidth of 15.7%(27.12-31.34 GHz)and 4.2%(37.21-38.81 GHz)for millimeter-wave applications with a gain of more than 4 dBi at both bands.The proposed antenna analysis in terms ofMIMOdiversity parameters(Envelope Correlation Coefficient(ECC)and Diversity Gain(DG))is also carried out.The experimental result in terms of reflection coefficient,radiation pattern,gain and MIMOdiversity parameter correlates very well with the simulated ones that show the potential of the proposed design for MIMO applications at millimeter-wave frequencies.

Experimental Study of Stacked Rectangular Microstrip Antenna for Dual-Band

A dual-band characteristic of stacked rectangular microstrip antenna is experimentally studied. It is a probe fed antenna for impedance matching with 50Ω coaxial cable. This antenna works well in the frequency range (2.86 to 4.63 GHz). It is basically a low cost, light weight medium gain antenna, which is used for mobile communication. The variations of the length and width (1mm) of the stacked rectangular patch antenna have been done. And it is found dual resonance with increasing lower resonance frequency and almost constant upper resonance frequency with increases of the length & width of rectangular microstrip antenna. The input impedance and VSWR, return loss have been measured with the help of Network analyzer.

Aperture Coupled Microstrip Antenna for Dual-Band

This paper presents air gap aperture coupled microstrip antenna for dual-band operation over the frequency range of (2.9 to 6.0 GHz). This antenna differs from any other microstrip antenna with their feeding structure of the radiating patch element. Input signal couples to the radiating patch trough the aperture that exists on the ground plane of microstrip feed line. The dual-band achieved by variation of air gap [2 mm to 6 mm] between single patch antenna and aper-ture coupled microstrip antenna. The main advantage of this type antenna is increased the bandwidth of the antenna as compared to a single layered patch antenna. The two resonant frequencies can vary over a wide frequency range and the input impedance is easily matched for both frequencies. The obtain ratios of resonance frequencies are variable from 2.1 GHz to 1.1 GHz with increasing the air gap between single patch and aperture coupled microstrip antenna. The measured return loss [–14 dB] exhibits an impedance bandwidth of 35%. The input impedance and VSWR return loss have been measured with the help of Network analyzer.

Electromagnetic coupling reduction in dual-band microstrip antenna array using ultra-compact single-negative electric metamaterials for MIMO application

In this paper, an ultra-compact single negative（SNG） electric waveguided metamaterial（WG-MTM） is first investigated and used to reduce the mutual coupling in E ＆ H planes of a dual-band microstrip antenna array. The proposed SNG electric WG-MTM unit cell is designed by etching two different symmetrical spiral lines on the ground, and has two stopbands operating at 1.86 GHz and 2.40 GHz. The circuit size is very compact, which is only λ_0/33.6 ×λ_0/15.1（where λ_0 is the wavelength at 1.86 GHz in free space）. Taking advantage of the dual-stopband property of the proposed SNG electric WG-MTM, a dual-band microstrip antenna array operating at 1.86 GHz and 2.40 GHz with very low mutual coupling is designed by embedding a cross shaped array of the proposed SNG electric WG-MTM. The measured and simulated results of the designed dual-band antenna array are in good agreement with each other, indicating that the mutual coupling of the fabricated dual-band antenna array realizes 9.8/11.1 d B reductions in the H plane, 8.5/7.9 d B reductions in the E plane at1.86 GHz and 2.40 GHz, respectively. Besides, the distance of the antenna elements in the array is only 0.35 λ_0（where λ_0 is the wavelength at 1.86 GHz in free space）. The proposed strategy is used for the first time to reduce the mutual coupling in E ＆ H planes of the dual-band microstrip antenna array by using ultra-compact SNG electric WG-MTM.

Dual-band and high-isolation shared-aperture antenna for broadband airborne applications

A dual-band and high-isolation shared-aperture antenna for unmanned aerial vehicle(UAV)platforms has been proposed.This shared-aperture antenna consists of a rectangular monopole antenna and a 4-element multiple input multiple output(MIMO)antenna.In order to increase the isolation,several double split ring metamaterial(MTM)structures are introduced between antenna elements.The antenna radiator and the MTM structure are located on the front and back of the same dielectric substrate,respectively,and are perpendicular to a circular metal plate.The overall size of the antenna substrate is 124 mm×38 mm×1.016 mm.Moreover,the antenna prototype is constructed and measured,and the simulated and measured results are in good agreement.The measured results show that the-10 dB bandwidth of the monopole antenna is 1.92 GHz to 2.75 GHz,and the common-6.0 dB bandwidth of the MIMO antenna element is 4.75 GHz to 4.91 GHz,covering 2.2 GHz to 2.4 GHz in the S-band and 4.8 GHz to 4.9 GHz in the 5G band,respectively.In the 5G band,the isolation between any element of the MIMO antenna and the S-band monopole antenna is not less than 21 dB,and the isolation between the MIMO antenna elements is better than 23 dB,indicating t-hat the isolation between the antenna elements is high.The proposed antenna is suitable for the application on UAV airborne platforms.

A compact dual-band radiation system

Complex magnetically insulated transmission line oscillator(MILO),as an important development direction,can enhance the power efficiency and generate dual-band high power microwaves(HPMs).A complex MILO and a preliminary dual-band radiation system have been proposed in our previous studies.However,the axial length of the dual-band radiation system is too long to meet the compact requirements.In this paper,a compact dual-band radiation system is presented and investigated numerically.The compact dual-band radiation system comprises a dual-band cross-shaped mode converter and a dual-band coaxial conical horn antenna.It can convert two coaxial TEM mode microwaves(1.717 GHz and 4.167 GHz)generated by the complex MILO into the coaxial TE11 mode microwaves,and then radiate them into the air.At 1.717 GHz,the gain of the antenna is 17.9 dB,and the total return loss and diffraction loss are 1.50%and 0,respectively.At 4.167 GHz,the gain is 19.4 dB,and the total return loss and diffraction loss are 1.17%and 0.78%,respectively.The power handling capacity of the antenna is 5.1 GW at 1.717 GHz and 2.0 GW at 4.167 GHz.Comparing with the original structure,the length of the dual-band radiation system is reduced by 45.2%.

Metamaterials and Metamaterial-Based Antenna Technology

The study of metamaterials is among the most important and attractive topics of the electromagnetic field theory and applications in the past 15 years.Much effort has been devoted to scientific research into the new physical phenomena with great progress.This paper presents the thoughts about the applications of metamaterials in innovative antenna designs from an engineering perspective.The new understanding of metamaterials offers us great possibility to translate the physical concepts of metamaterials in laboratories to innovative antenna designs in practical engineering applications.The technologies have been successfully developed,significantly improving key performances of antennas at microwave and millimeter-wave bands.The recently invented metamaterial-based antennas demonstrate not only wide operating bandwidth,high antenna efficiency,high gain,but also significantly reduced volume with simple mechanical structures.

BDS机载天线增益适航性分析与验证

基于航空无线电技术委员会(Radio Technical Committee for Aeronautics,RTCA)等的相关技术标准,结合卫星通信链路预算理论,给出全球导航卫星系统(Global Navigation Satellite System,GNSS)机载天线增益适航性分析的理论方法,并对北斗卫星导航系统(Beidou Navigation Satellite System,BDS)机载天线增益进行适航性分析计算。以BDS机载天线增益适航性分析结果为设计指标进行BDS B1I频段机载无源天线的验证设计与仿真。BDS机载无源天线仿真结果满足设计指标,并具有良好的低仰角增益与圆极化性能。证明了所给GNSS机载天线增益适航性分析方法的可行性与BDS机载天线增益适航性分析结果的合理性。

Progress in dual-band dual-polarization shared-aperture SAR antennas

The progress in dual-band dual-polarization(DBDP)shared-aperture antennas for the synthetic aperture radar(SAR)application in the last decade is reviewed.Several designs of DBDP SAR antenna arrays are introduced with their main performances,then their comparison is summarized.In addition,some techniques enhancing DBDP antenna performances are presented.

一种集成滤波器和天线的低剖面双功能射频器

文中介绍了一种低剖面的双端口射频器件,它集成了一个二阶滤波器和双极化天线。文中采用选择性耦合技术来抑制谐振器的谐波,从而为滤波器提供宽阻带。同时,谐振器本身作为馈线,为一个贴片天线提供了双极化辐射,而不会占用额外的器件面积。天线的工作频率位于滤波器的第二谐波频率点。由于采用选择性耦合技术,谐波模式不会影响天线的性能,这意味着天线和滤波器的工作频率比可以扩展。为了验证该设计方案,文中制作并测试了所提出的双端口射频器件。实验结果表明,该器件在1.81 GHz处作为双极化天线工作,同时在0.9 GHz处作为滤波器工作。在天线功能方面,水平和垂直极化状态下的测量峰值增益分别为5.5 dBi和5.8 dBi。两种极化状态之间的辐射性能具有良好的一致性。在滤波器功能方面,它的工作频率位于0.8 GHz,具有高选择性和宽阻带(0.9 GHz~2.0 GHz)的特性。该器件的总剖面为2.5 mm。基于以上性能,所提出的射频器件可以为未来低剖面、高集成度的通信系统设计提供方案。

用于Wi-Fi频段的新型双频天线设计

通过对实现双频技术的分析研究,设计了一种新型紧凑单馈的双频天线。该天线采用单层微带馈线和开缝接地板构成,分别印制在介质板2侧。天线的面积只有20×26mm2。天线的工作频段分别为2.40～2.53GHz和5.00～5.96GHz,同时,运用HFSS10电磁仿真软件对影响工作频率的参数进行了分析和研究。最后对制作的实物进行测试,测试结果与仿真结果基本吻合。提出的天线仅改变了接地板的结构就可实现具有小型化和双频段的特性,适用于无线通信领域。

用投影预变换提高自适应波束形成的稳健性

在快拍数较少和（或）存在系统误差时，自适应波束形成的性能会变差，特别是会引起方向图副瓣电平升高——波束畸变。本文提出的投影变换法利用干扰方向的初略估计，在未精确预知阵列流形的条件下，可以显著改善自适应方向图的副瓣性能，并提高自适应算法的收敛性，计算机仿真结果验证了这一优点。