A 5MS/s 12-Bit Successive Approximation Analog-to-Digital Converter

With the continuous development of science and technology, digital signal processing is more and more widely used in various fields. Among them, the analog-to-digital converter (ADC) is one of the key components to convert analog signals to digital signals. As a common type of ADC, 12-bit sequential approximation analog-to-digital converter (SAR ADC) has attracted extensive attention for its performance and application. This paper aims to conduct in-depth research and analysis of 12-bit SAR ADC to meet the growing demands of digital signal processing. This article designs a 12-bit, successive approximation analog-to-digital converter (SAR ADC) with a sampling rate of 5 MS/s. The overall circuit adopts a fully differential structure, with key modules including DAC capacitor array, comparator, and control logic. According to the DAC circuit in this paper, a fully differential capacitor DAC array structure is proposed to reduce the area of layout DAC. The comparator uses a digital dynamic comparator to improve the ADC conversion speed. The chip is designed based on the SMIC180 nm CMOS process. The simulation results show that when the sampling rate is 5 MS/s, the effective bit of SAR ADC is 11.92 bit, the SNR is 74.62 dB, and the SFDR is 89.24 dB.

Overview of Energy-Efficient Successive-Approximation Analog-to-Digital Converters: State-of-the-Art and a Design Example

This paper makes a review of state-of-the- arts designs of successive-approximation register analog-to-digital converters （SAR ADCs）. Methods and technique specifications are collected in view of innovative ideas. At the end of this paper, a design example is given to illustrate the procedure to design an SAR ADC. A new method, which extends the width of the internal clock, is also proposed to facilitate different sampling frequencies, which provides more time for the digital-to-analog convert （DAC） and comparator to settle. The 10 bit ADC is simulated in 0.13 μm CMOS process technology. The signal-to-noise and distortion ratio （SNDR） is 54.41 dB at a 10 MHz input with a 50 MS/s sampling rate, and the power is 330 μW.

Effect of ionizing radiation on dual 8-bit analog-to-digital converters (AD9058) with various dose rates and bias conditions

The radiation effects on several properties （reference voltage, digital output logic voltage, and supply current） of dual 8-bit analog-to-digital （A/D） converters （AD9058） under various biased conditions are investigated in this paper. Gamma ray and 10-MeV proton irradiation are selected for a detailed evaluation and comparison. Based on the measurement results induced by the gamma ray with various dose rates, the devices exhibit enhanced low dose rate sensitivity （ELDRS） under zero and working bias conditions. Meanwhile, it is obvious that the ELDRS is more severe under the working bias condition than under the zero bias condition. The degradation of AD9058 does not display obvious ELDRS during 10-MeV proton irradiation with the selected flux.

Design of Digital to Analog Converters with Arbitrary Radix

There are DAC structures available in the literature for radix r = 2, 3, and 4;but how they are arrived at is missing. No general structure is available for any radix r. The aim of the paper is, therefore, to fulfil these gaps. To start with, the design relations are derived for the simplest possible attenuator circuit when connected to a voltage source V and a series resistance R, such that the complete circuit offers the Thevenin resistance R. Spread relations for this attenuator are derived. An example when 3 such attenuators with different attenuation constants are connected in cascade is given. Interestingly, the two attenuators with attenuation factors 1/2 and 1/3 have the same spread of 2. A generalized attenuator is then obtained when N number of identical attenuators are connected in cascade. This is modified to derive a digital to analog converter for any radix r.

A 1.5 bit/s Pipelined Analog-to-Digital Converter Design with Independency of Capacitor Mismatch

A new technique which is named charge temporary storage technique (CTST) was presented to improve the linearity of a 1.5 bit/s pipelined analog-to-digital converter (ADC). The residual voltage was obtained from the sampling capacitor, and the other capacitor was just a temporary storage of charge. Then, the linearity produced by the mismatch of these capacitors was eliminated without adding extra capacitor error-averaging amplifiers. The simulation results confirmed the high linearity and low dissipation of pipelined ADCs implemented in CTST, so CTST was a new method to implement high resolution, small size ADCs.

Novel Optical Analog-To-Digital Converter Based on Optical Time Division Multiplexing

A novel optical analog-to-digital converter based on optical time division multiplexing(OTDM) is described which uses electrooptic sampling and time-demultiplexing together with multiple electronic analog-to-digital converter(ADC). Compared with the previous scheme, the time-division multiplexer and the time-division demultiplexer are applied in the optical analog-to-digital converter(OADC) at the same time, the design of the OADC is simplified and the performance of the OADC based on time-division demultiplexer is improved. A core optical part of the system is demonstrated with a sample rate of 10 Gs/s. The signals in three channels are demultiplexed from the optical pulses.The result proves our scheme is feasible.

Analog-to-digital conversion of information in the retina

We considered the physiological mechanisms of functioning of the retina’s neural network. It is marked that the primary function of a neural network is an analog-to-digital conversion of the receptor potential of photoreceptor into the pulse-to-digital signal to ganglion cells. We showed the role of different types of neurons in the work of analog-to-digital converter. We gave the equivalent circuit of this converter. We researched the mechanism of the numeric coding of the receptor potential of the photoreceptor.

Ionizing radiation effect on 10-bit bipolar A/D converter

In this article,radiation effects and annealing characteristics of a bipolar analog-to-digital converter(ADC) are investigated in different biases and dose rates.The results show that ADC is sensitive to both the bias and dose rate. Under high-dose-rate irradiation,the ADC functions well,while under low-dose-rate irradiation,the parameters of ADC change obviously at low dose level,and the damage is significant at zero bias.Combining the fringing field with the space charge model,the underlying mechanism for this response is discussed.

A FAST FOREGROUND DIGITAL CALIBRATION TECHNIQUE FOR PIPELINED ADC

Digital calibration techniques are widely developed to cancel the non-idealities of the pipelined Analog-to-Digital Converters (ADCs). This letter presents a fast foreground digital calibration technique based on the analysis of error sources which influence the resolution of pipelined ADCs. This method estimates the gain error of the ADC prototype quickly and calibrates the ADC simultaneously in the operation time. Finally, a 10 bit, 100 Ms/s pipelined ADC is implemented and calibrated. The simulation results show that the digital calibration technique has its efficiency with fewer operation cycles.

320×240 Pixels CMOS Digital Image Sensor with Wide Dynamic Range

A 320×240 CMOS image sensor is demonstrated,which is implemented by a standard 0.6 μm 2P2M CMOS process.For reducing the chip area,each 2×2-pixel block shares a sample/hold circuit,analog-to-digital converter and 1-b memory.The 2×2 pixel pitch has an area of 40 μm×40 μm and the fill factor is about 16%.While operating at a low frame rate,the sensor dissipates a very low power by power-management circuit making pixel-level comparators in an idle state.A digital correlated double sampling,which eliminates fixed pattern noise,improves SNR of the sensor, and multiple sampling operations make the sensor have a wide dynamic range.

DIGITAL BACKGROUND CALIBRATION OF CAPACITOR MISMATCHES AND HARMONIC DISTORTION IN PIPELINED ADC

A correlation-based digital background calibration algorithm for pipelined Analog-to- Digital Converters (ADCs) is presented in this paper. The merit of the calibration algorithm is that the main errors information, which include the capacitor mismatches and residue amplifier distortion, are extracted integrally. A modified 1st pipelined stage is adopted to solve the signal overflow caused by the Pseudo-random Noise (PN) sequences. Behavioral simulation results verify the effectiveness of the algorithm. It improves the Signal-to-Noise-plus-Distortion Ratio (SNDR) and Spurious-Free-Dynamic-Range (SFDR) of the pipelined ADC from 41.8 dB to 78.3 dB and 55.6 dB to 98.6 dB, respectively, which is comparable to the prior arts.

基于0.18μm SiGe BiCMOS工艺的4GS/s、14 bit数模转换器

基于0.18μm SiGe BiCMOS工艺,设计了超高速高精度数模转换器(DAC),其时钟采样率为4 GS/s、精度为14 bit。为满足4 GHz处理速度,该DAC中所有电路均采用异质结晶体管(HBTs)搭建。为了降低功耗和节约面积,本设计采用10+4分段译码的方式,其中低10位电流舵使用R-2R梯形电阻网络,而高4位使用温度计码结构。仿真结果表明,所设计DAC的DNL、INL分别为0.54 LSB和0.39 LSB,全奈奎斯特频域内的无杂散动态范围均大于82 dBc。在3.3 V和5 V混合电源供电下,整个DAC的平均功耗为2.39 W。芯片总面积为11.22 mm^(2)。

一种应用于12 bit SAR ADC C-R混和式DAC

针对ADC中功耗、精度与成本之间相互制约的问题,提出一种应用于12 bitSARADC的混合电容电阻型(C-R)DAC结构。高6位采用温度计编码的电容阵列结构;低6位选择电阻阵列结构。对电路进行非线性分析选取合理的元件尺寸。另外,采用非交叠时钟电路作为开关控制时序,避免开关切换时引起瞬态毛刺导致电容电荷泄露。基于GSMC 95 nm工艺,完成电路、版图设计与仿真,并完成流片测试,DAC版图总面积为317.2μm×262.5μm,流片测试结果表明,DNL的范围为-0.38~+0.44 LSB,INL的范围为-0.73~+0.4 LSB,满足12位ADC的设计要求。

A digital calibration technique for an ultra high-speed wide-bandwidth folding and interpolating analog-to-digital converter in 0.18-μm CMOS technology

A digital calibration technique for an ultra high-speed folding and interpolating analog-to-digital con- verter in 0.18-μm CMOS technology is presented. The similar digital calibration techniques are taken for high 3-bit flash converter and low 5-bit folding and interpolating converter, which are based on well-designed calibration reference, calibration DAC and comparators. The spice simulation and the measured results show the ADC produces 5.9 ENOB with calibration disabled and 7.2 ENOB with calibration enabled for high-frequency wide-bandwidth analog input.

A 12-bit 250-MS/s Charge-Domain Pipelined Analog-to-Digital Converter with Feed-Forward Common-Mode Charge Control

A feed-forward Common-Mode （CM） charge control circuit for a high-speed Charge-Domain （CO） pipelined Analog-to-Digital Converter （ADC） is presented herein. This study aims at solving the problem whereby the precision of CD pipelined ADCs is restricted by the variation in input CM charge, which can compensate for CM charge errors caused by a variation in CM charge input in real time. Based on the feed-forward CM charge control circuit, a 12-bit 250-MS/s CD pipelined ADC is designed and realized using a 1P6M 0.18-μm CMOS process. The ADC achieved a Spurious Free Dynamic Range （SFDR） of 78.1 dB and a Signal-to-Noise-and-Distortion Ratio （SNDR） of 64.6 dB for a 20.1-MHz input; a SFDR of 74.9 dB and SNDR of 62.0 dB were achieved for a 239.9-MHz input at full sampling rate. The variation in signal-to-noise ratio was less than 3 dB over a 0-1.2 V input CM voltage range. The power consumption of the prototype ADC is only 85 mW at 1.8 V supply, and it occupies an active die area of 2.24 mm^2.

An optimized analog to digital converter for WLAN analog front end

A 10 bit 80 MSPS analog to digital converter optimized for WLAN analog front end is presented. In contrast to conventional 1.5 bit pipeline architecture, four optimized multiit multiply digital to analog converter stages are implemented. An on-chip low-noise reference buffer is proposed for SoC integration purposes, and a wide-bandwidth wide swing sample and hold amplifier is also presented for achieving a good dynamic range. The converter was fabricated in 0.18 #m 1P6M CMOS technology, and the core area occupies approximately 0.85 mm2. Measured results show that with an 11 MHz input signal, it provides a 9.4 bit effective number of bits and a 72 dBc spurious frequency dynamic range when sampled at 80 MHz.

基于量子电压的模数转换器性能评估

相比于用传统半导体器件研制的信号源,约瑟夫森任意波形发生器合成信号的幅值可溯源至自然常数,其输出波形具有超低噪声、超低失真的优点。使用约瑟夫森任意波形发生器评估了National Instruments公司24位数字采集卡PXI 5922的性能。其中,采用零补偿波形合成方法简化系统硬件结构,并且使用高精度、多比例的感应分压器提升评估效率。首先,在10 kHz的带宽内标定了PXI 5922单通道的增益及其稳定性、信噪比、无杂散动态范围、总谐波失真、信纳比和有效位数;其次,标定了PXI 5922两通道不同相位下的相位差;最后,结合电网的谐波情况,以60 Hz的基波频率为例,标定了PXI 5922在12阶谐波以内各谐波的幅度与相位响应。约瑟夫森任意波形发生器的超高精度和宽带输出能力在评估高精度模数转换器的性能方面具有广阔的应用前景。

一种16位110 dB无杂散动态范围的低功耗SAR ADC

该文设计了一款16位、转换速率为625 kS/s的逐次逼近寄存器型模数转换器(SAR ADC)。改进的采样保持电路结构,优化了采样线性度和噪声性能。采用分段结构设计电容型数模转换器并使用混合方式的电容切换方案,减小面积和能耗。利用扰动注入技术提升ADC的线性度。比较器采用两级积分型预放大器减小噪声,利用输出失调存储技术及优化的电路设计减小了比较器失调电压和失调校准引入的噪声,优化并提升了比较器速度。芯片采用CMOS 0.18μm工艺设计和流片,ADC核心面积为1.15 mm^(2)。测试结果表明,在1 kHz正弦信号输入下,ADC差分输入峰峰值幅度达8.8 V,信纳比为85.9 dB,无杂散动态范围为110 dB,微分非线性为-0.27/+0.32 LSB,积分非线性为-0.58/+0.53 LSB,功耗为4.31 mW。

一种6倍无源增益低OSR低功耗的二阶NS SAR ADC

针对一阶噪声整形(NS)往往需要增加功耗而以较高的过采样比(OSR)来实现较高的有效位数(ENOB),提出了一种低OSR、低功耗的二阶无源NS SAR ADC。该无源NS模块较高的无源增益可以更好地抑制比较器的噪声;其残差电压是通过开关MOS阵列复用积分电容实现采样,从而无需额外的残差采样电容,避免了残差采样电容清零和残差采样时kT/C噪声的产生,因此减小了总的kT/C噪声。180 nm CMOS工艺仿真结果表明,在不使用数字校准的情况下,所设计的10位二阶无源NS SAR ADC电路以100 kS/s的采样率和5的OSR,实现了13.5位ENOB,电路功耗仅为6.98μW。

基于高速ADC的数字双混频时差测量系统

使用双混频时差法进行时间和频率测量时,模拟部分引入的噪声会干扰信号过零点的判断,降低测量精度,而使用数字信号处理技术后不再需要判断过零点,量化噪声成为系统内的主要噪声来源,可以通过数字滤波器对其进行抑制。同时有利于设计结构紧凑的系统,更易于小型化,测量速度也可以进行灵活配置。通过引入高速模数转换器、数控振荡器、低通抽取滤波器、数字鉴相器等,设计了数字双混频时差测量系统,并研制了4通道的原理样机。测试结果表明,当频率源为10 MHz的信号时,原理样机中属于同片ADC(analog-to-digital converter)的两个通道间的本底噪声约为5×10^(-14)@1 s,属于不同片ADC的两个通道间的本底噪声约为8×10^(-14)@1 s,满足原子振荡器的测量要求。并以主动型氢钟VCH-1003M为参考,使用原理样机分别对Microchip的5071A铯原子钟和SRS的FS725铷原子钟的稳定度进行测量,测量结果与Microchip的相噪分析仪53100A和5120A无显著差异。