Brittleness is a dominant issue that restricts potential applications of Mg_2Si intermetallic compounds(IMC). In this paper, guided by first-principles calculations, we found that Al doping will enhance the ductility ...Brittleness is a dominant issue that restricts potential applications of Mg_2Si intermetallic compounds(IMC). In this paper, guided by first-principles calculations, we found that Al doping will enhance the ductility of Mg_2Si. The underlying mechanism is that Al doping could reduce the electronic exchange effect between Mg and Si atoms, and increase the volume module/shear modulus ratio, both of which are beneficial to the deformation capability of Mg_2Si. Experimental investigations were then carried out to verify the calculation results with Al doping contents ranging from Al-free to 10 wt%. Results showed that the obtained ductile-brittle transition temperature of the Mg_2Si–Al alloy decreased and the corresponding ductility increased. Specifically, the ductile-brittle transition temperature could be reduced by about 100℃. When the content of Al reached 6 wt%, α-Al phase started to precipitate, and the ductile-brittle transition temperature of the alloy no longer decreased.展开更多
The effect of Al content on the ductile-brittle transition temperature of Al-Si coating and the effect of fracture behaviour.of the Al-Si coating on the fatigue properties of Ni-base superallovs have been investigated...The effect of Al content on the ductile-brittle transition temperature of Al-Si coating and the effect of fracture behaviour.of the Al-Si coating on the fatigue properties of Ni-base superallovs have been investigated to propose the theoretical basis of search for an optimum of mechanical properties of the high temperature coating on Ni-base alloys.展开更多
The ductile to brittle transition temperature (DBTT) of the modified 9Cr-1Mo steel and its laser welds was studied. The increase in grain size of the weld structure ascended the DBTT of the steel significantly. The tr...The ductile to brittle transition temperature (DBTT) of the modified 9Cr-1Mo steel and its laser welds was studied. The increase in grain size of the weld structure ascended the DBTT of the steel significantly. The transformation of retained austenite at martensite interlath boundaries into untempered and/or twinned martensite could also contribute to increased DBTTs of the steel and its welds tempered at 540℃.展开更多
The brittle–ductile transition(BDT) widely exists in the manufacturing with extremely small deformation scale, thermally assisted machining, and high-speed machining. This paper reviews the BDT in extreme manufacturi...The brittle–ductile transition(BDT) widely exists in the manufacturing with extremely small deformation scale, thermally assisted machining, and high-speed machining. This paper reviews the BDT in extreme manufacturing. The factors affecting the BDT in extreme manufacturing are analyzed, including the deformation scale and deformation temperature induced brittle-to-ductile transition, and the reverse transition induced by grain size and strain rate. A discussion is arranged to explore the mechanisms of BDT and how to improve the machinability based on the BDT. It is proposed that the mutual transition between brittleness and ductility results from the competition between the occurrence of plastic deformation and the propagation of cracks. The brittleness or ductility of machined material should benefit a specific manufacturing process, which can be regulated by the deformation scale, deformation temperature and machining speed.展开更多
In order to better understand the relation between grain boundary characteristic distribution （GBCD） and the brittle cracking of ferritic stainless steel, the GBCD, impact test and bend test were investigated using ...In order to better understand the relation between grain boundary characteristic distribution （GBCD） and the brittle cracking of ferritic stainless steel, the GBCD, impact test and bend test were investigated using scanning electron microscopy （SEM） and the electron backscatter diffraction （EBSD） technique. The results show that a crack occurs preferentially at high angle boundaries, and that low angle and low-∑ coincidence site lattice（CSL） boundaries can offer resistance to the propagation of cracks. It is suggested that an optimum GBCD, i.e. a high frequency of low angle or low-∑ CSL boundaries and discontinuous high angle boundaries network can offer the potential for decreasing the ductile-to-brittle transition temoerature （DBTT） of ferritic stainless steels.展开更多
基金financially supported by the National Key Research and Development Program of China (No. 2016YFB0700500)the National Natural Science Foundation of China (No. 51574027)
文摘Brittleness is a dominant issue that restricts potential applications of Mg_2Si intermetallic compounds(IMC). In this paper, guided by first-principles calculations, we found that Al doping will enhance the ductility of Mg_2Si. The underlying mechanism is that Al doping could reduce the electronic exchange effect between Mg and Si atoms, and increase the volume module/shear modulus ratio, both of which are beneficial to the deformation capability of Mg_2Si. Experimental investigations were then carried out to verify the calculation results with Al doping contents ranging from Al-free to 10 wt%. Results showed that the obtained ductile-brittle transition temperature of the Mg_2Si–Al alloy decreased and the corresponding ductility increased. Specifically, the ductile-brittle transition temperature could be reduced by about 100℃. When the content of Al reached 6 wt%, α-Al phase started to precipitate, and the ductile-brittle transition temperature of the alloy no longer decreased.
文摘The effect of Al content on the ductile-brittle transition temperature of Al-Si coating and the effect of fracture behaviour.of the Al-Si coating on the fatigue properties of Ni-base superallovs have been investigated to propose the theoretical basis of search for an optimum of mechanical properties of the high temperature coating on Ni-base alloys.
文摘The ductile to brittle transition temperature (DBTT) of the modified 9Cr-1Mo steel and its laser welds was studied. The increase in grain size of the weld structure ascended the DBTT of the steel significantly. The transformation of retained austenite at martensite interlath boundaries into untempered and/or twinned martensite could also contribute to increased DBTTs of the steel and its welds tempered at 540℃.
基金support from the National Natural Science Foundation of China (Grant No. 51835004)。
文摘The brittle–ductile transition(BDT) widely exists in the manufacturing with extremely small deformation scale, thermally assisted machining, and high-speed machining. This paper reviews the BDT in extreme manufacturing. The factors affecting the BDT in extreme manufacturing are analyzed, including the deformation scale and deformation temperature induced brittle-to-ductile transition, and the reverse transition induced by grain size and strain rate. A discussion is arranged to explore the mechanisms of BDT and how to improve the machinability based on the BDT. It is proposed that the mutual transition between brittleness and ductility results from the competition between the occurrence of plastic deformation and the propagation of cracks. The brittleness or ductility of machined material should benefit a specific manufacturing process, which can be regulated by the deformation scale, deformation temperature and machining speed.
文摘In order to better understand the relation between grain boundary characteristic distribution （GBCD） and the brittle cracking of ferritic stainless steel, the GBCD, impact test and bend test were investigated using scanning electron microscopy （SEM） and the electron backscatter diffraction （EBSD） technique. The results show that a crack occurs preferentially at high angle boundaries, and that low angle and low-∑ coincidence site lattice（CSL） boundaries can offer resistance to the propagation of cracks. It is suggested that an optimum GBCD, i.e. a high frequency of low angle or low-∑ CSL boundaries and discontinuous high angle boundaries network can offer the potential for decreasing the ductile-to-brittle transition temoerature （DBTT） of ferritic stainless steels.
