Effect of quenching process on the microstrucmre and mechanical properties of a kind of seamless tubes of steel 28CrMnMoV was investigated. Then, an investigation on the influence of two different quenching processes ...Effect of quenching process on the microstrucmre and mechanical properties of a kind of seamless tubes of steel 28CrMnMoV was investigated. Then, an investigation on the influence of two different quenching processes on the ductile-brittle transition behavior of this steel was undertaken. The ductile-brittle transition temperatures of the steel by two different quenching processes were also determined. The results show that a good combination of mechanical properties can be obtained through austenitizing experimental steel at 800 ℃ or 890 ℃ followed by tempering at 630 ℃. Ductile-to-brittle transition temperature of 28CrMnMoV steel austenitized at 800 ℃ followed by tempering at 640 ℃ is about -73 ℃, which is much lower than the value -37 ℃ when the steel was austenitized at 890℃ and then tempered at 650 ℃. This indicates that subcritical quenching process could decrease largely the ductile-to-brittle transition temperature of 28CrMnMoV steel.展开更多
Brittleness is a dominant issue that restricts potential applications of Mg_2Si intermetallic compounds(IMC). In this paper, guided by first-principles calculations, we found that Al doping will enhance the ductility ...Brittleness is a dominant issue that restricts potential applications of Mg_2Si intermetallic compounds(IMC). In this paper, guided by first-principles calculations, we found that Al doping will enhance the ductility of Mg_2Si. The underlying mechanism is that Al doping could reduce the electronic exchange effect between Mg and Si atoms, and increase the volume module/shear modulus ratio, both of which are beneficial to the deformation capability of Mg_2Si. Experimental investigations were then carried out to verify the calculation results with Al doping contents ranging from Al-free to 10 wt%. Results showed that the obtained ductile-brittle transition temperature of the Mg_2Si–Al alloy decreased and the corresponding ductility increased. Specifically, the ductile-brittle transition temperature could be reduced by about 100℃. When the content of Al reached 6 wt%, α-Al phase started to precipitate, and the ductile-brittle transition temperature of the alloy no longer decreased.展开更多
Based on the crack tip structure a new model of ductile -brittle transition was proposed. Using this new model we calculated the dependence of the transition temperature-strain rate over a wide range of strain rate. F...Based on the crack tip structure a new model of ductile -brittle transition was proposed. Using this new model we calculated the dependence of the transition temperature-strain rate over a wide range of strain rate. Finally the significance of this new model is discussed in detail.展开更多
The surface of sequence boundary is a negative record. Its recognition largely depends on the physics of the sediments below and above the boundaries, or on the different sedimentary structures are synthetic marks for...The surface of sequence boundary is a negative record. Its recognition largely depends on the physics of the sediments below and above the boundaries, or on the different sedimentary structures are synthetic marks for the sedimentation and tectonic movements in the sedimentary basin. The Qiangtang Basin that is in 5000m above the sea level is located in Northern Tibet. The Lazhulung—Jinshajiang suture zone now bound it to the north and the Bangong—Nujiang suture zone to the south. Three second\|order tectonic units have been distinguished, i.e. North Qiangtang depression, Central rise and South Qiangtang depression from north to south.The Upper Permian Riejuichaka Formation is built up of mudstone and mud\|limestone, which is represented by sediments in seamarsh. The Lower Triassic Kuanglu Formation, which exhibits the structure unconformable contact with the overlying Upper Permian strata, is characterized by terrigenous clastic rocks in the lower area and is carbonate rocks in the upwarding area and the Middle Triassic Kuangnan Formation. The Upper Triassic Xiachaka Formation consisting of terrigenous clastic rocks, carbonates rocks and mixed sediments, is confined to the uplift zones. The lower Jurassic volcanic rocks are deposited in continental rift. The middle and Upper Jurassic Yangshiping Group are conformable contact and assembled by the gypsum\|bearing terrigenous clastic rock formations and carbonate rock formation. The Middle Cretaceous and the Paleocene strata is built up of the terrigenous clastic rock formations.展开更多
The dynamic fracture toughness of a mild steel has been studied at different loading rates and temperatures.The material exhibits a transition from tough to brittle fracture with the chang- ing loading rate alone.Anal...The dynamic fracture toughness of a mild steel has been studied at different loading rates and temperatures.The material exhibits a transition from tough to brittle fracture with the chang- ing loading rate alone.Analysis of the fracture process by the theory of thermal activation suggests that the fracture activation energy approximates to the bond energy of the{100}of a unit cell.The toughness can be resolved into two parts,J-(fd)=J_a+J_l,where J_a is the athermal part,being independent on temperature and loading rate,while J_l=(K/K_o)^(1/n)exp(Q_f/nkT),which controls the fracture process is temperature and load- ing rate dependent.The transition of fracture mechanism caused by both temperature and loading rate is associated with the thermal movement of atoms.展开更多
Effects of hydrogen on the mechanical properties of differently aged 7175 aluminum alloys were investigated by using cathodic H-permeation, slow strain rate tension and so on. The results indicate that both the yield ...Effects of hydrogen on the mechanical properties of differently aged 7175 aluminum alloys were investigated by using cathodic H-permeation, slow strain rate tension and so on. The results indicate that both the yield stress and the percentage reduction of area decrease with increasing hydrogen charging time, and the degree of reduction decreases as aging time increases for the same hydrogen charging time.展开更多
The present work investigates the effect of europium substitution on the （Bi, Pb）-2212 system in the concentration range 0.5 ≤ x ≤1.0. Phase analysis and lattice parameter calculations on the powder diffraction da...The present work investigates the effect of europium substitution on the （Bi, Pb）-2212 system in the concentration range 0.5 ≤ x ≤1.0. Phase analysis and lattice parameter calculations on the powder diffraction data and the elemental analysis of EDX show that the Eu atoms are successfully substituted into the （Bi, Pb）-2212 system. Resistivity measurements （64-300 K） reveal that the system exhibits superconductivity at x ≤ 0.5 and semiconductivity at x 〉 0.5. With the complete suppression of superconductivity which is known to be a quasi-two dimensional phenomenon in these materials, a metal to insulator transition takes place at x = 0.6 and the predominant conduction mechanism is found to be variable range hopping between localized states, resulting in macroscopic semiconducting behaviour. The results of electrical and structural properties of the doped （Bi, Pb）-2212 compounds suggest that the decrease of charge carrier concentration and the induced structural disorder are the more effective and dominant mechanisms in the origin of the metal to insulator transition and suppression of superconductivity due to Eu substitution at its Sr site.展开更多
The effect of Al content on the ductile-brittle transition temperature of Al-Si coating and the effect of fracture behaviour.of the Al-Si coating on the fatigue properties of Ni-base superallovs have been investigated...The effect of Al content on the ductile-brittle transition temperature of Al-Si coating and the effect of fracture behaviour.of the Al-Si coating on the fatigue properties of Ni-base superallovs have been investigated to propose the theoretical basis of search for an optimum of mechanical properties of the high temperature coating on Ni-base alloys.展开更多
On the insulating side of the metal-insulator transition (MIT), the study of the effect of low Temperatures T on the electrical transport in amorphous silicon-nickel alloys a-Si1-yNiy:H exhibits that the electrical co...On the insulating side of the metal-insulator transition (MIT), the study of the effect of low Temperatures T on the electrical transport in amorphous silicon-nickel alloys a-Si1-yNiy:H exhibits that the electrical conductivity follows, at the beginning, the Efros-Shklovskii Variable Range Hopping regime (ES VRH) with T-1/2. This behaviour showed that long range electron-electron interaction reduces the Density Of State of carriers (DOS) at the Fermi level and creates the Coulomb gap (CG). For T higher than a critical value of temperature TC, we obtained the Mott Variable Range Hopping regime with T-1/4, indicating that the DOS becomes almost constant in the vicinity of the Fermi level. The critical temperature TC decreases with nickel content in the alloys.展开更多
To improve the performance of composite pseudo-noise （PN） code clock recovery in a regenerative PN ranging system at a low symbol signal-to-noise ratio （SNR）, a novel chip tracking loop （CTL） used for regenerati...To improve the performance of composite pseudo-noise （PN） code clock recovery in a regenerative PN ranging system at a low symbol signal-to-noise ratio （SNR）, a novel chip tracking loop （CTL） used for regenerative PN ranging clock recovery is adopted. The CTL is a modified data transition tracking loop （DTTL）. The difference between them is that the Q channel output of the CTL is directly multiplied by a clock component, while that of the DTTL is multiplied by the Ⅰ channel transition detector output. Under the condition of a quasi-squareware PN ranging code, the tracking （ mean square timing jitter） performance of the CTL is analyzed. The tracking performances of the CTL and the DTTL, are compared over a wide range of symbol SNRs. The result shows that the CTL and the DTTL have the same performance at a large symbol SNR, while at a low symbol SNR, the former offers a noticeable enhancement.展开更多
Magneto-plasticity occurs when a weak magnetic field alters material plasticity and offers a viable solution to enhance ductile-mode cutting of brittle materials.This study demonstrates the susceptibility of non-magne...Magneto-plasticity occurs when a weak magnetic field alters material plasticity and offers a viable solution to enhance ductile-mode cutting of brittle materials.This study demonstrates the susceptibility of non-magnetic single-crystal calcium fluoride(CaF_(2))to the magneto-plastic effect.The influence of magneto-plasticity on CaF_(2) was confirmed in micro-deformation tests under a weak magnetic field of 20 mT.The surface pile-up effect was weakened by 10-15 nm along with an enlarged plastic zone and suppressed crack propagation under the influence of the magnetic field.Micro-cutting tests along different crystal orientations on the(111)plane of CaF_(2) revealed an increase in the ductile-brittle transition of the machined surface with the aid of magneto-plasticity where the largest increase in ductile-brittle transition occurred along the[112]orientation from 512 nm to a range of 664-806 nm.Meanwhile,the subsurface damage layer was concurrently thinner under magnetic influence.An anisotropic influence of the magnetic field relative to the single-crystal orientation and the cutting direction was also observed.An analytical model was derived to determine an orientation factor M that successfully describes the anisotropy while considering the single-crystal dislocation behaviour,material fracture toughness,and the orientation of the magnetic field.Previously suggested theoretical mechanism of magneto-plasticity via formation of non-singlet electronic states in defected configurations was confirmed with density functional theory calculations.The successful findings on the influence of a weak magnetic field on plasticity present an opportunity for the adoption of magnetic-assisted micro-cutting of non-magnetic materials.展开更多
基金Project(2008FJ1003)supported by the Hunan Province Science and Technology,China
文摘Effect of quenching process on the microstrucmre and mechanical properties of a kind of seamless tubes of steel 28CrMnMoV was investigated. Then, an investigation on the influence of two different quenching processes on the ductile-brittle transition behavior of this steel was undertaken. The ductile-brittle transition temperatures of the steel by two different quenching processes were also determined. The results show that a good combination of mechanical properties can be obtained through austenitizing experimental steel at 800 ℃ or 890 ℃ followed by tempering at 630 ℃. Ductile-to-brittle transition temperature of 28CrMnMoV steel austenitized at 800 ℃ followed by tempering at 640 ℃ is about -73 ℃, which is much lower than the value -37 ℃ when the steel was austenitized at 890℃ and then tempered at 650 ℃. This indicates that subcritical quenching process could decrease largely the ductile-to-brittle transition temperature of 28CrMnMoV steel.
基金financially supported by the National Key Research and Development Program of China (No. 2016YFB0700500)the National Natural Science Foundation of China (No. 51574027)
文摘Brittleness is a dominant issue that restricts potential applications of Mg_2Si intermetallic compounds(IMC). In this paper, guided by first-principles calculations, we found that Al doping will enhance the ductility of Mg_2Si. The underlying mechanism is that Al doping could reduce the electronic exchange effect between Mg and Si atoms, and increase the volume module/shear modulus ratio, both of which are beneficial to the deformation capability of Mg_2Si. Experimental investigations were then carried out to verify the calculation results with Al doping contents ranging from Al-free to 10 wt%. Results showed that the obtained ductile-brittle transition temperature of the Mg_2Si–Al alloy decreased and the corresponding ductility increased. Specifically, the ductile-brittle transition temperature could be reduced by about 100℃. When the content of Al reached 6 wt%, α-Al phase started to precipitate, and the ductile-brittle transition temperature of the alloy no longer decreased.
文摘Based on the crack tip structure a new model of ductile -brittle transition was proposed. Using this new model we calculated the dependence of the transition temperature-strain rate over a wide range of strain rate. Finally the significance of this new model is discussed in detail.
文摘The surface of sequence boundary is a negative record. Its recognition largely depends on the physics of the sediments below and above the boundaries, or on the different sedimentary structures are synthetic marks for the sedimentation and tectonic movements in the sedimentary basin. The Qiangtang Basin that is in 5000m above the sea level is located in Northern Tibet. The Lazhulung—Jinshajiang suture zone now bound it to the north and the Bangong—Nujiang suture zone to the south. Three second\|order tectonic units have been distinguished, i.e. North Qiangtang depression, Central rise and South Qiangtang depression from north to south.The Upper Permian Riejuichaka Formation is built up of mudstone and mud\|limestone, which is represented by sediments in seamarsh. The Lower Triassic Kuanglu Formation, which exhibits the structure unconformable contact with the overlying Upper Permian strata, is characterized by terrigenous clastic rocks in the lower area and is carbonate rocks in the upwarding area and the Middle Triassic Kuangnan Formation. The Upper Triassic Xiachaka Formation consisting of terrigenous clastic rocks, carbonates rocks and mixed sediments, is confined to the uplift zones. The lower Jurassic volcanic rocks are deposited in continental rift. The middle and Upper Jurassic Yangshiping Group are conformable contact and assembled by the gypsum\|bearing terrigenous clastic rock formations and carbonate rock formation. The Middle Cretaceous and the Paleocene strata is built up of the terrigenous clastic rock formations.
文摘The dynamic fracture toughness of a mild steel has been studied at different loading rates and temperatures.The material exhibits a transition from tough to brittle fracture with the chang- ing loading rate alone.Analysis of the fracture process by the theory of thermal activation suggests that the fracture activation energy approximates to the bond energy of the{100}of a unit cell.The toughness can be resolved into two parts,J-(fd)=J_a+J_l,where J_a is the athermal part,being independent on temperature and loading rate,while J_l=(K/K_o)^(1/n)exp(Q_f/nkT),which controls the fracture process is temperature and load- ing rate dependent.The transition of fracture mechanism caused by both temperature and loading rate is associated with the thermal movement of atoms.
文摘Effects of hydrogen on the mechanical properties of differently aged 7175 aluminum alloys were investigated by using cathodic H-permeation, slow strain rate tension and so on. The results indicate that both the yield stress and the percentage reduction of area decrease with increasing hydrogen charging time, and the degree of reduction decreases as aging time increases for the same hydrogen charging time.
基金supported by Kerala State Council for Science,Technology and Environment,Council of Scientific and Industrial Researchthe University Grants Commission of India
文摘The present work investigates the effect of europium substitution on the （Bi, Pb）-2212 system in the concentration range 0.5 ≤ x ≤1.0. Phase analysis and lattice parameter calculations on the powder diffraction data and the elemental analysis of EDX show that the Eu atoms are successfully substituted into the （Bi, Pb）-2212 system. Resistivity measurements （64-300 K） reveal that the system exhibits superconductivity at x ≤ 0.5 and semiconductivity at x 〉 0.5. With the complete suppression of superconductivity which is known to be a quasi-two dimensional phenomenon in these materials, a metal to insulator transition takes place at x = 0.6 and the predominant conduction mechanism is found to be variable range hopping between localized states, resulting in macroscopic semiconducting behaviour. The results of electrical and structural properties of the doped （Bi, Pb）-2212 compounds suggest that the decrease of charge carrier concentration and the induced structural disorder are the more effective and dominant mechanisms in the origin of the metal to insulator transition and suppression of superconductivity due to Eu substitution at its Sr site.
文摘The effect of Al content on the ductile-brittle transition temperature of Al-Si coating and the effect of fracture behaviour.of the Al-Si coating on the fatigue properties of Ni-base superallovs have been investigated to propose the theoretical basis of search for an optimum of mechanical properties of the high temperature coating on Ni-base alloys.
文摘On the insulating side of the metal-insulator transition (MIT), the study of the effect of low Temperatures T on the electrical transport in amorphous silicon-nickel alloys a-Si1-yNiy:H exhibits that the electrical conductivity follows, at the beginning, the Efros-Shklovskii Variable Range Hopping regime (ES VRH) with T-1/2. This behaviour showed that long range electron-electron interaction reduces the Density Of State of carriers (DOS) at the Fermi level and creates the Coulomb gap (CG). For T higher than a critical value of temperature TC, we obtained the Mott Variable Range Hopping regime with T-1/4, indicating that the DOS becomes almost constant in the vicinity of the Fermi level. The critical temperature TC decreases with nickel content in the alloys.
文摘To improve the performance of composite pseudo-noise （PN） code clock recovery in a regenerative PN ranging system at a low symbol signal-to-noise ratio （SNR）, a novel chip tracking loop （CTL） used for regenerative PN ranging clock recovery is adopted. The CTL is a modified data transition tracking loop （DTTL）. The difference between them is that the Q channel output of the CTL is directly multiplied by a clock component, while that of the DTTL is multiplied by the Ⅰ channel transition detector output. Under the condition of a quasi-squareware PN ranging code, the tracking （ mean square timing jitter） performance of the CTL is analyzed. The tracking performances of the CTL and the DTTL, are compared over a wide range of symbol SNRs. The result shows that the CTL and the DTTL have the same performance at a large symbol SNR, while at a low symbol SNR, the former offers a noticeable enhancement.
基金supported by the Ministry of Education,Singapore,under its Academic Research Funds(Grant Nos.:MOE-T2EP50120-0010,MOE-T2EP50220-0010)the funding from the Ministère des Relations Internationales et de la Francophonie du Québec,Coopération Québec-Singapour,with which this work was partially supported。
文摘Magneto-plasticity occurs when a weak magnetic field alters material plasticity and offers a viable solution to enhance ductile-mode cutting of brittle materials.This study demonstrates the susceptibility of non-magnetic single-crystal calcium fluoride(CaF_(2))to the magneto-plastic effect.The influence of magneto-plasticity on CaF_(2) was confirmed in micro-deformation tests under a weak magnetic field of 20 mT.The surface pile-up effect was weakened by 10-15 nm along with an enlarged plastic zone and suppressed crack propagation under the influence of the magnetic field.Micro-cutting tests along different crystal orientations on the(111)plane of CaF_(2) revealed an increase in the ductile-brittle transition of the machined surface with the aid of magneto-plasticity where the largest increase in ductile-brittle transition occurred along the[112]orientation from 512 nm to a range of 664-806 nm.Meanwhile,the subsurface damage layer was concurrently thinner under magnetic influence.An anisotropic influence of the magnetic field relative to the single-crystal orientation and the cutting direction was also observed.An analytical model was derived to determine an orientation factor M that successfully describes the anisotropy while considering the single-crystal dislocation behaviour,material fracture toughness,and the orientation of the magnetic field.Previously suggested theoretical mechanism of magneto-plasticity via formation of non-singlet electronic states in defected configurations was confirmed with density functional theory calculations.The successful findings on the influence of a weak magnetic field on plasticity present an opportunity for the adoption of magnetic-assisted micro-cutting of non-magnetic materials.
