Brittleness is a dominant issue that restricts potential applications of Mg_2Si intermetallic compounds(IMC). In this paper, guided by first-principles calculations, we found that Al doping will enhance the ductility ...Brittleness is a dominant issue that restricts potential applications of Mg_2Si intermetallic compounds(IMC). In this paper, guided by first-principles calculations, we found that Al doping will enhance the ductility of Mg_2Si. The underlying mechanism is that Al doping could reduce the electronic exchange effect between Mg and Si atoms, and increase the volume module/shear modulus ratio, both of which are beneficial to the deformation capability of Mg_2Si. Experimental investigations were then carried out to verify the calculation results with Al doping contents ranging from Al-free to 10 wt%. Results showed that the obtained ductile-brittle transition temperature of the Mg_2Si–Al alloy decreased and the corresponding ductility increased. Specifically, the ductile-brittle transition temperature could be reduced by about 100℃. When the content of Al reached 6 wt%, α-Al phase started to precipitate, and the ductile-brittle transition temperature of the alloy no longer decreased.展开更多
The effect of Al content on the ductile-brittle transition temperature of Al-Si coating and the effect of fracture behaviour.of the Al-Si coating on the fatigue properties of Ni-base superallovs have been investigated...The effect of Al content on the ductile-brittle transition temperature of Al-Si coating and the effect of fracture behaviour.of the Al-Si coating on the fatigue properties of Ni-base superallovs have been investigated to propose the theoretical basis of search for an optimum of mechanical properties of the high temperature coating on Ni-base alloys.展开更多
The comparative study of submerged arc welding(SAW)and laser hybrid welding(LHW)was carried out for a 690 MPa high strength steel with thickness of 20 mm.Microstructure and ductile–brittle transition temperature(DBTT...The comparative study of submerged arc welding(SAW)and laser hybrid welding(LHW)was carried out for a 690 MPa high strength steel with thickness of 20 mm.Microstructure and ductile–brittle transition temperature(DBTT)evolution in welded zone were elucidated from the aspect of crystallographic structure,particularly,digitization and visualization of 24 variants.The impact toughness of each micro zone in LHW joint is better than that of SAW,in which the DBTT of equivalent fusion line and heat-affected zone(HAZ)can reach−70 and−80℃,while that of SAW is only−50℃.LHW technology induces narrowing of the HAZ and refining of the microstructure obtained in weld metal and HAZ.Meanwhile,the austenite grain size and transformation driving force in the coarse grained heat-affected zone(CGHAZ)are reduced and increased,respectively.It makes variant selection mechanism occurring in CGHAZ of LHW dominate by close-packed plane grouping,which promotes lath bainite formation with high density of high angle grain boundary,especially block boundary dominated by V1/V2 pair.While for SAW,the lower transformation driving force inferred from the large amount of retained austenite in CGHAZ induces Bain grouping of variants,and thus triggers the brittle crack propagating straightly in granular bainite,resulting in lower impact toughness and higher DBTT.展开更多
Mechanical and magnetic properties as well as their relationship in the reduced activation martensitic （RAM） steel were investigated in the temperature range from -90℃ to 20℃. Charpy impact tests show that the duc...Mechanical and magnetic properties as well as their relationship in the reduced activation martensitic （RAM） steel were investigated in the temperature range from -90℃ to 20℃. Charpy impact tests show that the ductile-to-brittle transition temperature （DBTT） of the RAM steel is about -60℃. Low-temperature tensile tests show that the yield strength, ultimate tensile strength and total elongation values increase as temperature decreases, indicating that the strength and plasticity below the DBTT are higher than those above the DBTT. The coercive field （Hc） in the scale of logarithm decreases linearly with the increasing temperature and the absolute value of the slope of InHc versus temperature above the DBTT is obviously larger than that below the DBTT, also confirmed in the T91 steel. The results indicate that the non-destructive magnetic measurement is a promising candidate method for the DBTT detection of ferromagnetic steels.展开更多
The effects of Ti-Mo-V composite addition on the evolution of precipitates in marine 10Ni5CrMoV steel andthe corresponding strength and toughness mechanisms were systematically investigated.Ti-Mo-V composite addition ...The effects of Ti-Mo-V composite addition on the evolution of precipitates in marine 10Ni5CrMoV steel andthe corresponding strength and toughness mechanisms were systematically investigated.Ti-Mo-V composite addition canform the Ti_(x)Mo_(y)V_(z)C carbide with TiC as core and Mo-V as shell in the order of Ti(C)→V→Mo.The yield strength of thespecimens is increased from 815 MPa to 876 MPa due to the nanoscale precipitates enhancing the pinning effect on grainboundaries and dislocations,and the contribution of precipitation and dislocation strengthening is increased.The decrease of ductile-brittle transition temperature from−103 to−116℃is attributed to the decrease in equivalent grainsize and the increase of high-angle grain boundary misorientation,which hinders the initiation and propagation of cracks.When the mass fraction of Ti is 0.05%,the strength and cryogenic toughness can be improved synergistically,which alsoprovides a theoretical basis and experimental reference for exploring the more excellent combination of strength andcryogenic toughness of marine 10Ni5CrMoV steel.展开更多
A hot-rolled steel with high yield strength of 700 MPa, good elongation of about 20% and low ductile-brittle transition temperature （DBTT） lower than -70℃ has been developed in laboratory. The results show that ado...A hot-rolled steel with high yield strength of 700 MPa, good elongation of about 20% and low ductile-brittle transition temperature （DBTT） lower than -70℃ has been developed in laboratory. The results show that adopting finishing rolling temperature of around 800℃ is rational, and coiling temperature is between 400 and 500℃ The strength of developed 700 MPa hot-rolled high strength steel is derived from the cumulative contribution of fine grain size, dislocation hardening and precipitation hardening. The fine grain strengthening and precipitation hardening are the dominant factors responsible for such high strength, and good elongation and toughness are predominantly due to fine grain ferrite.展开更多
In order to explore the eff ect of a small amount of rare earth addition in ultra-cleaned pipeline steel and the influence of the cooling process on the tensile and impact properties,three API X80 pipeline steels were...In order to explore the eff ect of a small amount of rare earth addition in ultra-cleaned pipeline steel and the influence of the cooling process on the tensile and impact properties,three API X80 pipeline steels were fabricated by varying RE addition and the cooling process at the same time.Three microstructures with different features for a low C high Nb microalloyed high-strength pipeline steel and the corresponding mechanical properties were investigated.The results showed that even in the ultra-cleaned steel with O and S contents less than 10 ppm,the addition of RE would still cause an increase in the volume fraction of inclusions consisting of complicated RE oxysulfide and RE sulfide.More inclusions formed in the 112 ppm RE steel were harmful to the low temperature toughness,while few inclusions formed in the 47 ppm RE steel had almost no influence on the low temperature toughness.The two RE additions had no effect on strength of the steels.As the finishing cooling temperature was increased and the cooling rate was decreased within a certain range,the volume fractions of polygonal ferrite and quasi-polygonal ferrite as well as the number density and size of martensite–austenite islands were increased.Under such combined effect,the strength of the steels had almost no change.As the finishing cooling temperature was increased from 481 to 584℃and the cooling rate was reduced from 20 to 13℃/s,for the steel with 112 ppm addition of RE,there was an obvious decrease in the low temperature toughness.The reduced value(about 33 J)of the USE of steel consisted of two parts including the influence(about 18 J)of more inclusions formed due to 112 ppm addition of RE and the eff ect(about 15 J)of the lower high-angle grain boundaries.展开更多
基金financially supported by the National Key Research and Development Program of China (No. 2016YFB0700500)the National Natural Science Foundation of China (No. 51574027)
文摘Brittleness is a dominant issue that restricts potential applications of Mg_2Si intermetallic compounds(IMC). In this paper, guided by first-principles calculations, we found that Al doping will enhance the ductility of Mg_2Si. The underlying mechanism is that Al doping could reduce the electronic exchange effect between Mg and Si atoms, and increase the volume module/shear modulus ratio, both of which are beneficial to the deformation capability of Mg_2Si. Experimental investigations were then carried out to verify the calculation results with Al doping contents ranging from Al-free to 10 wt%. Results showed that the obtained ductile-brittle transition temperature of the Mg_2Si–Al alloy decreased and the corresponding ductility increased. Specifically, the ductile-brittle transition temperature could be reduced by about 100℃. When the content of Al reached 6 wt%, α-Al phase started to precipitate, and the ductile-brittle transition temperature of the alloy no longer decreased.
文摘The effect of Al content on the ductile-brittle transition temperature of Al-Si coating and the effect of fracture behaviour.of the Al-Si coating on the fatigue properties of Ni-base superallovs have been investigated to propose the theoretical basis of search for an optimum of mechanical properties of the high temperature coating on Ni-base alloys.
基金financially supported by the National Natural Science Foundation of China(No.52001023)the Special Fund for Science and Technology Project of Guangdong Province(No.SDZX2020008)the Key Research and Development Program of Shandong Province,China(No.2019JZZY020238).
文摘The comparative study of submerged arc welding(SAW)and laser hybrid welding(LHW)was carried out for a 690 MPa high strength steel with thickness of 20 mm.Microstructure and ductile–brittle transition temperature(DBTT)evolution in welded zone were elucidated from the aspect of crystallographic structure,particularly,digitization and visualization of 24 variants.The impact toughness of each micro zone in LHW joint is better than that of SAW,in which the DBTT of equivalent fusion line and heat-affected zone(HAZ)can reach−70 and−80℃,while that of SAW is only−50℃.LHW technology induces narrowing of the HAZ and refining of the microstructure obtained in weld metal and HAZ.Meanwhile,the austenite grain size and transformation driving force in the coarse grained heat-affected zone(CGHAZ)are reduced and increased,respectively.It makes variant selection mechanism occurring in CGHAZ of LHW dominate by close-packed plane grouping,which promotes lath bainite formation with high density of high angle grain boundary,especially block boundary dominated by V1/V2 pair.While for SAW,the lower transformation driving force inferred from the large amount of retained austenite in CGHAZ induces Bain grouping of variants,and thus triggers the brittle crack propagating straightly in granular bainite,resulting in lower impact toughness and higher DBTT.
文摘Mechanical and magnetic properties as well as their relationship in the reduced activation martensitic （RAM） steel were investigated in the temperature range from -90℃ to 20℃. Charpy impact tests show that the ductile-to-brittle transition temperature （DBTT） of the RAM steel is about -60℃. Low-temperature tensile tests show that the yield strength, ultimate tensile strength and total elongation values increase as temperature decreases, indicating that the strength and plasticity below the DBTT are higher than those above the DBTT. The coercive field （Hc） in the scale of logarithm decreases linearly with the increasing temperature and the absolute value of the slope of InHc versus temperature above the DBTT is obviously larger than that below the DBTT, also confirmed in the T91 steel. The results indicate that the non-destructive magnetic measurement is a promising candidate method for the DBTT detection of ferromagnetic steels.
基金Project(2023YFE0200300)supported by the National Key K&D Program of ChinaProject(52174303,51874084)supported by the National Natural Science Foundation of ChinaProject(B21001)supported by the Introducing Talents of Discipline to Universities,China。
文摘The effects of Ti-Mo-V composite addition on the evolution of precipitates in marine 10Ni5CrMoV steel andthe corresponding strength and toughness mechanisms were systematically investigated.Ti-Mo-V composite addition canform the Ti_(x)Mo_(y)V_(z)C carbide with TiC as core and Mo-V as shell in the order of Ti(C)→V→Mo.The yield strength of thespecimens is increased from 815 MPa to 876 MPa due to the nanoscale precipitates enhancing the pinning effect on grainboundaries and dislocations,and the contribution of precipitation and dislocation strengthening is increased.The decrease of ductile-brittle transition temperature from−103 to−116℃is attributed to the decrease in equivalent grainsize and the increase of high-angle grain boundary misorientation,which hinders the initiation and propagation of cracks.When the mass fraction of Ti is 0.05%,the strength and cryogenic toughness can be improved synergistically,which alsoprovides a theoretical basis and experimental reference for exploring the more excellent combination of strength andcryogenic toughness of marine 10Ni5CrMoV steel.
基金Item Sponsored by High Technology Development Program of China(2001AA332020)
文摘A hot-rolled steel with high yield strength of 700 MPa, good elongation of about 20% and low ductile-brittle transition temperature （DBTT） lower than -70℃ has been developed in laboratory. The results show that adopting finishing rolling temperature of around 800℃ is rational, and coiling temperature is between 400 and 500℃ The strength of developed 700 MPa hot-rolled high strength steel is derived from the cumulative contribution of fine grain size, dislocation hardening and precipitation hardening. The fine grain strengthening and precipitation hardening are the dominant factors responsible for such high strength, and good elongation and toughness are predominantly due to fine grain ferrite.
基金financially supported by the National Key Research and Development Program of China(Grant No.2017YFB0304901)。
文摘In order to explore the eff ect of a small amount of rare earth addition in ultra-cleaned pipeline steel and the influence of the cooling process on the tensile and impact properties,three API X80 pipeline steels were fabricated by varying RE addition and the cooling process at the same time.Three microstructures with different features for a low C high Nb microalloyed high-strength pipeline steel and the corresponding mechanical properties were investigated.The results showed that even in the ultra-cleaned steel with O and S contents less than 10 ppm,the addition of RE would still cause an increase in the volume fraction of inclusions consisting of complicated RE oxysulfide and RE sulfide.More inclusions formed in the 112 ppm RE steel were harmful to the low temperature toughness,while few inclusions formed in the 47 ppm RE steel had almost no influence on the low temperature toughness.The two RE additions had no effect on strength of the steels.As the finishing cooling temperature was increased and the cooling rate was decreased within a certain range,the volume fractions of polygonal ferrite and quasi-polygonal ferrite as well as the number density and size of martensite–austenite islands were increased.Under such combined effect,the strength of the steels had almost no change.As the finishing cooling temperature was increased from 481 to 584℃and the cooling rate was reduced from 20 to 13℃/s,for the steel with 112 ppm addition of RE,there was an obvious decrease in the low temperature toughness.The reduced value(about 33 J)of the USE of steel consisted of two parts including the influence(about 18 J)of more inclusions formed due to 112 ppm addition of RE and the eff ect(about 15 J)of the lower high-angle grain boundaries.
