This paper describes a study into the development of more robust dust emission factors by means of dust and meteorological monitoring. Emission factors for nuisance dusts in the literature are scarce, with estimates o...This paper describes a study into the development of more robust dust emission factors by means of dust and meteorological monitoring. Emission factors for nuisance dusts in the literature are scarce, with estimates of dust output given for many processes in mass per unit area per year. Temporal variations and the extent and conditions in which maximum concentrations occur can therefore be impossible to predict with any accuracy. This investigation aims to improve predic-tions by “back calculating” emission levels based on dust monitoring around known dust sources. Nuisance dust and meteorological monitoring has been undertaken at a sand and gravel quarry in the UK for a consecutive period of two years. Sticky pad directional dust monitors were used to collect dust at eight locations at and around the site with meteorological data collected at an elec-tronic weather station within the site. Air quality modelling software (ADMS) was used to test emission factors from the European Environment Agency (EEA) and the US Environmental Protec-tion Agency (EPA) for emissions from mineral workings. Predictions were compared with the dust monitoring data to assess accuracy, with results showing limited poor correspondence (r<sup>2</sup> < 0.3). Trends showed that emission predictions were poorest in winter;this is likely because most emis-sion calculations are not weather dependent and seasonal fluctuations will occur. Dust emission rate calculations were altered with respect to the dust monitoring data for one monitoring location on the mineral site boundary and the model was run again. Results were then tested at two different locations up to 200 m from the site boundary, with very positive correlations (r<sup>2</sup > 0.89) and similar maximum concentrations (<5% difference). This study has therefore shown that ac-curate site-specific emission rates can be produced in combination with site boundary sticky pad dust monitoring in order to accurately derive estimations elsewhere.展开更多
The effects of natural andgeochemical factors depending on heavy metal contamination in nuisance dust particles were evaluated. The nuisance dust particles were sampled using passive deposit gauge method for one year ...The effects of natural andgeochemical factors depending on heavy metal contamination in nuisance dust particles were evaluated. The nuisance dust particles were sampled using passive deposit gauge method for one year from April2010 to March2011 and the obtained samples were measured for the total contents and the contamination levels of Fe, Mn, Cu and As usinggeo-accumulation index （Igeo ）, enrichment factor （EF） and the integrated pollution index （IPI）. The results showed that, the contamination levels of Fe and Mn based on Igeo values, were uncontaminated （Igeo 〈 0） （variations of the Igeo index was from -3.11 to -1.751 for Fe, from -0.630 to -1.925 for Mn）, while the values of Cu and As were demonstrated to have moderate contamination based on Igeo values （variations of Igeo index was from -1.125 to 0.848 for Cu, and from -2.002 to 1.249 for As）. The analysis of EF also revealed minor to moderate enrichment for Mn （1.215-4.214）, minor to moderately severe enrichment for Cu （2.791-6.484）, and As （1.370-8.462）, respectively. The variation of the IPI index also showed low to moderate level of heavy metal pollution in nuisance dust particulates （0.511-1.829）. The analysis of the results also approved that the natural processes andgeochemical variables （the changing meteorological parameters） can significantly affect the availability of heavy metals in nuisance dust particles in Western Iran.展开更多
文摘This paper describes a study into the development of more robust dust emission factors by means of dust and meteorological monitoring. Emission factors for nuisance dusts in the literature are scarce, with estimates of dust output given for many processes in mass per unit area per year. Temporal variations and the extent and conditions in which maximum concentrations occur can therefore be impossible to predict with any accuracy. This investigation aims to improve predic-tions by “back calculating” emission levels based on dust monitoring around known dust sources. Nuisance dust and meteorological monitoring has been undertaken at a sand and gravel quarry in the UK for a consecutive period of two years. Sticky pad directional dust monitors were used to collect dust at eight locations at and around the site with meteorological data collected at an elec-tronic weather station within the site. Air quality modelling software (ADMS) was used to test emission factors from the European Environment Agency (EEA) and the US Environmental Protec-tion Agency (EPA) for emissions from mineral workings. Predictions were compared with the dust monitoring data to assess accuracy, with results showing limited poor correspondence (r<sup>2</sup> < 0.3). Trends showed that emission predictions were poorest in winter;this is likely because most emis-sion calculations are not weather dependent and seasonal fluctuations will occur. Dust emission rate calculations were altered with respect to the dust monitoring data for one monitoring location on the mineral site boundary and the model was run again. Results were then tested at two different locations up to 200 m from the site boundary, with very positive correlations (r<sup>2</sup > 0.89) and similar maximum concentrations (<5% difference). This study has therefore shown that ac-curate site-specific emission rates can be produced in combination with site boundary sticky pad dust monitoring in order to accurately derive estimations elsewhere.
文摘The effects of natural andgeochemical factors depending on heavy metal contamination in nuisance dust particles were evaluated. The nuisance dust particles were sampled using passive deposit gauge method for one year from April2010 to March2011 and the obtained samples were measured for the total contents and the contamination levels of Fe, Mn, Cu and As usinggeo-accumulation index （Igeo ）, enrichment factor （EF） and the integrated pollution index （IPI）. The results showed that, the contamination levels of Fe and Mn based on Igeo values, were uncontaminated （Igeo 〈 0） （variations of the Igeo index was from -3.11 to -1.751 for Fe, from -0.630 to -1.925 for Mn）, while the values of Cu and As were demonstrated to have moderate contamination based on Igeo values （variations of Igeo index was from -1.125 to 0.848 for Cu, and from -2.002 to 1.249 for As）. The analysis of EF also revealed minor to moderate enrichment for Mn （1.215-4.214）, minor to moderately severe enrichment for Cu （2.791-6.484）, and As （1.370-8.462）, respectively. The variation of the IPI index also showed low to moderate level of heavy metal pollution in nuisance dust particulates （0.511-1.829）. The analysis of the results also approved that the natural processes andgeochemical variables （the changing meteorological parameters） can significantly affect the availability of heavy metals in nuisance dust particles in Western Iran.
