Switching Frequency Improvement of a High Speed on/off Valve Based on Pre-excitation Control Algorithm

The high-speed on/off valve(HSV)serves as the fundamental component responsible for generating discrete fluids within digital hydraulic systems.As the switching frequency of the HSV increases,the properties of the generated discrete fluid approach those of continuous fluids.Therefore,a higher frequency response characteristic of HSV is the key to ensure the control accuracy of digital hydraulic systems.However,the current research mainly focuses on its dynamic performance,but neglect its FRC.This paper presents a theoretical analysis demonstrating that the FRC of the HSV can be enhanced by minimizing its switching time.The maximum switching frequency(MSF)is mainly determined by opening dynamic performance when HSV operates with low switching duty ratio(SDR),whereas the closing dynamic performance limits the MSF when HSV operates with high SDR.Building upon these findings,the pre-excitation control algorithm(PECA)is proposed to reduce the switching time of the HSV,and consequently enhance its FRC.Experimental results demonstrate that PECA shortens the opening delay time of HSV by 1.12 ms,the closing delay time by 2.54 ms,and the closing moving time by 0.47 ms in comparison to the existing advanced control algorithms.As a result,a larger MSF of 417 Hz and a wider controllable SDR range from 20%to 70%were achieved at a switching frequency of 250 Hz.Thus,the proposed PFCA in this paper has been verified as an effective and promising approach for enhancing the control performance of digital hydraulic systems.

Modeling the System for Hybrid Renewable Energy Using Highly Efficient Converters and Generator

High-efficient isolated DC/DC converters with a high-efficiency synchronous reluctance generator(SRG)are the ultimate solutions in DC microgrid systems.The design and modeling of isolated DC/DC converters with the performance of SRG are carried out.On the generator side,reactive and active powers are used as pulse width modulation(PWM)control variables.Further,the flux estimator is used.Three-phase PWM rectifier is used by applying space vector modulation(SVM)with a constant switching frequency for direct power control.Further,the paper also includes the experimental validation of the results.The paper also proposes that highly efficient power converters and synchronous reluctance generators are required to achieve high performance for hybrid renewable energy systems applications.

Role of Duty Ratio in Diamond Growth by Pulsed DC-Bias Enhanced Hot Filament Chemical Vapour Deposition

In this study, the role of the pulse duty ratio was investigated during the deposition of diamond films in a hot filament chemical vapour deposition reactor with a pulsed-tic biased substrate positively relative to the hot filaments. The voltage-current characteristics showed that the discharge current rose with the increase of biasing voltage, which was modified by the duty ratio. Before deposition, two approaches were adopted for the pre-treatment of the silicon substrates, respectively, and the substrates were scratched by diamond paste or seeded by diamond powders using the so-called ＇soft dry polished＇ technique. Diamond films were deposited under a fixed discharge power by changing the duty ratios. In the first group with scratched substrates, it was found that under a high duty ratio the diamond grew slowly with quite poor nucleation, while in the second case a high duty ratio induced a high deposition rate and good diamond qual- ity. Reactive hydrocarbon species with high energy are essential for the initial nucleation process, which is more effectively achieved at a high biasing voltage in the condition of a low duty ratio. In the film growth process, the large discharge current at a high duty ratio represents an increased concentration of electrons and reactive species as well, promoting the growth of diamond films.

Effects of electrical parameters and their interactions on plasma electrolytic oxidation coatings on aluminum substrates

Based on orthogonal experiments,the effects of voltage,frequency,duty ratio and their interactions on the thickness and corrosion resistance of coatings prepared by plasma electrolytic oxidation(PEO)on aluminum in an alkaline silicate-containing electrolyte were investigated.The thicknesses of these coatings were obtained by measuring their cross-section using Image J software.Their corrosion resistances were evaluated in HCl and NaCl media through spot test and electrochemical test.The results show that the experimental design of this study is the key to investigate the interactions among these electrical parameters.Additionally,not only each independent factor,but also their interactions exhibit a remarkable influence on the coatings.The combination of high voltage,low frequency and large duty ratio significantly increases the coating thickness and content of the corrosion resistance phase,and thus improves the corrosion resistance of the coating in HNO3 medium.Conversely,the coating possessing the densest microstructure and best corrosion resistance in NaCl medium is obtained when low voltage and high frequency match with a small duty ratio.

In vivo hyperthermia effect induced by high-intensity pulsed ultrasound

Hyperthermia effects （39-44 ℃） induced by pulsed high-intensity focused ultrasound （HIFU） have been regarded as a promising therapeutic tool for boosting immune responses or enhancing drug delivery into a solid tumor. However, previous studies also reported that the cell death occurs when cells are maintained at 43 ℃ for more than 20 minutes. The aim of this study is to investigate thermal responses inside in vivo rabbit auricular veins exposed to pulsed HIFU （1.17 MHz, 5300 W/cm2, with relatively low-duty ratios （0.2%-4.3%）. The results show that： （1） with constant pulse repetition frequency （PRF） （e.g., 1 Hz）, the thermal responses inside the vessel will increase with the increasing duty ratio; （2） a temperature elevation to 43 ℃ can be identified at the duty ratio of 4.3%; （3） with constant duty ratios, the change of PRF will not significantly affect the temperature measurement in the vessel; （4） as the duty ratios lower than 4.3%, the presence of microbubbles will not significantly enhance the thermal responses in the vessel, but will facilitate HIFU-induced inertial cavitation events.

Passive Matrix Organic Electroluminescent Display for 3G Cellular Phone

The major features of the display technologies for 3G cellular phone are reviewed. The comparison between their potential candidates for 3G cellular phone is given, and a detailed discussion is made on passive matrix organic electroluminescent display technology. A novel method to improve display contrast ratio is presented. Finally several 3G phone set prototypes with OLED display panels are given as well as the market forecast.

ROBUST CONTROL OF GAS TUNGSTEN ARC WELDING SYSTEM

The robust control law for gas tungsten arc welding dynamic process, which is a typical sampled-data system and full of uncertainties, is presented. By using the Lyapunov, second method, the robust control and robust optimal control for a class of sampled-data systems whose underlying continuous-time systems are subjected to structured uncertainties are discussed in time-domain. As a result, some sufficient conditions of robust stability and the corresponding robust control laws are derived. All these results are designed by solving a class of linear matrix inequalities （LMIs） and a class of dynamic optimization problem with LMIs constraints respectively. An example adapted under some experimental conditions in the dynamic process of gas tungsten arc welding system in which the controlled variable is the backside width of weld pool and controlling variable pulse duty ratio, is worked out to illustrate the proposed results, it is shown that the sampling period is the crucial design oarameter.

Synthetic Effects of Frequency and Duty Ratio on Growth Characteristics, Energy Consumption and Corrosion Properties of Microarc Oxidized Coating Formed on Ti6Al4V

The synthetic effects of frequency and duty ratio on growth characteristics and corrosion properties of coating on Ti6Al4V fabricated by microarc oxidation are investigated comprehensively. Under the condition of uniform cumulating time of positive impulse width, the essence of altering frequency and duty ratio to determine the formation of coating is to vary the duration and interval time of positive pulse. The growth of coating is mainly controlled by duration time of positive pulse and hardly correlated to the interval time of positive pulse, while both duration and interval time of positive pulse have few influences on the morphology and phase structures of coating. The dynamic current is related to positive impulse width and the ratio of positive pulse on-time to pulse off-time. Regardless of uniform duration or interval time of positive pulse, the energy dissipation presents a descending tendency. The relationship between energy consumption and anticorrosion performance is contradictory, and obtaining excellent corrosion ratio and frequency can be designed purposefully to realize the resistance is bound to sacrifice lots of energy. The duty optimal process.