Dynamic Control System of Automatic Monitoring Equipment for Waste Gas Pollution Source

In order to improve the quality of automatic monitoring data of pollution sources and apply the automatic monitoring data to verify the environmental tax,Shandong Province took the lead in adopting the Internet of Things technology and drawing on the successful experience of air automatic monitoring stations and surface water automatic monitoring stations in management,and developed a dynamic management and control system for automatic monitoring equipment of pollution sources to improve and strengthen the quality audit of automatic monitoring data,further improve the quality of automatic monitoring data and better provide a basis for environmental management and decision making.The system realizes the simultaneous monitoring of monitoring data,running state and parameters of the automatic monitoring equipment,eliminates the phenomenon of falsification by modifying equipment parameters,and judges the validity of the collected data by acquiring the working state of the equipment remotely and randomly.After the actual operation test of the Department of Ecological Environment of Shandong Province,the system is proved to have the characteristics of practicality,real time and high efficiency,and be able to make up for low frequency and narrow coverage of manual inspection,with good application prospect in the field of environment and pollution source monitoring.

Dynamic Constraint-Driven Event-Triggered Control of Strict-Feedback Systems Without Max/Min Values on Irregular Constraints

This work proposes an event-triggered adaptive control approach for a class of uncertain nonlinear systems under irregular constraints.Unlike the constraints considered in most existing papers,here the external irregular constraints are considered and a constraints switching mechanism(CSM)is introduced to circumvent the difficulties arising from irregular output constraints.Based on the CSM,a new class of generalized barrier functions are constructed,which allows the control results to be independent of the maximum and minimum values(MMVs)of constraints and thus extends the existing results.Finally,we proposed a novel dynamic constraint-driven event-triggered strategy(DCDETS),under which the stress on signal transmission is reduced greatly and no constraints are violated by making a dynamic trade-off among system state,external constraints,and inter-execution intervals.It is proved that the system output is driven to close to the reference trajectory and the semi-global stability is guaranteed under the proposed control scheme,regardless of the external irregular output constraints.Simulation also verifies the effectiveness and benefits of the proposed method.

Dynamic event-triggered formation control of second-order nonholonomic systems

In this paper,the formation control problem of secondorder nonholonomic mobile robot systems is investigated in a dynamic event-triggered scheme.Event-triggered control protocols combined with persistent excitation(PE)conditions are presented.In event-detecting processes,an inactive time is introduced after each sampling instant,which can ensure a positive minimum sampling interval.To increase the flexibility of the event-triggered scheme,internal dynamic variables are included in event-triggering conditions.Moreover,the dynamic event-triggered scheme plays an important role in increasing the lengths of time intervals between any two consecutive events.In addition,event-triggered control protocols without forward and angular velocities are also presented based on approximate-differentiation(low-pass)filters.The asymptotic convergence results are given based on a nested Matrosov theorem and artificial sampling methods.

Fixed-Time Stabilization of a Class of Strict-Feedback Nonlinear Systems via Dynamic Gain Feedback Control

This paper presents a novel fixed-time stabilization control(FSC)method for a class of strict-feedback nonlinear systems involving unmodelled system dynamics.The key feature of the proposed method is the design of two dynamic parameters.Specifically,a set of auxiliary variables is first introduced through state transformation.These variables combine the original system states and the two introduced dynamic parameters,facilitating the closed-loop system stability analyses.Then,the two dynamic parameters are delicately designed by utilizing the Lyapunov method,ensuring that all the closed-loop system states are globally fixed-time stable.Compared with existing results,the“explosion of complexity”problem of backstepping control is avoided.Moreover,the two designed dynamic parameters are dependent on system states rather than a time-varying function,thus the proposed controller is still valid beyond the given fixedtime convergence instant.The effectiveness of the proposed method is demonstrated through two practical systems.

Emotion detection on webpages using biosensors integrated to a window-based dynamic control system

Purpose-Detecting emotion on user experience of web applications and browsing is important in many ways.Web designers and developers find such approach quite useful in enhancing navigational features of webpages,and biomedical personnel regularly use computer simulations to monitor and control the behaviour of patients.On the other hand,law enforcement agents rely on human physiological functions to determine the likelihood of falsehood in interrogations.Quite often,online user experience is studied via tangible measures such as task completion time,surveys and comprehensive tests from which data attributes are generated.Prediction of users’emotion and behaviour in some of these cases depends mostly on task completion time and number of clicks per given time interval.However,such approaches are generally subjective and rely heavily on distributional assumptions making the results prone to recording errors.Design/methodology/approach-The authors propose a novel method-a window dynamic control system that addresses the foregoing issues.Primary data were obtained from laboratory experiments during which forty-four volunteers had their synchronised physiological readings,skin conductance response(SCR),skin temperature(ST),eye movement behaviour and users’activity attributes taken using biosensors.The windowbased dynamic control system(PHYCOB I)is integrated to the biosensor which collects secondary data attributes from these synchronised physiological readings and uses them for two purposes.For both detection of optimal emotional responses and users’stress levels.The method’s novelty derives from its ability to integrate physiological readings and eye movement records to identify hidden correlates on a webpage.Findings-Results show that the control system detects basic emotions and outperforms other conventional models in terms of both accuracy and reliability,when subjected to model comparison that is,the average recoverable natural structures for the three models with respect to accuracy and reliability are more consistent within the window-based control system environment than with the conventional methods.Research limitations/implications-The paper is limited to using a window control system to detect emotions on webpages,while integrated to biosensors and eye-tracker.Originality/value-The originality of the proposed model is its resistance to overfitting and its ability to automatically assess human emotion(stress levels)while dealing with specific web contents.The latter is particularly important in that it can be used to predict which contents of webpages cause stress-induced emotions to users when involved in online activities.

Adaptive Fuzzy Dynamic Surface Control of Flexible-Joint Robot Systems With Input Saturation

In this paper, we propose an adaptive fuzzy dynamic surface control(DSC) scheme for single-link flexible-joint robotic systems with input saturation. A smooth function is utilized with the mean-value theorem to deal with the difficulties associated with input saturation. An adaptive DSC design with an auxiliary first-order filter is used to solve the "explosion of complexity"problem. It is proved that all the signals in the closed-loop system are semi-globally uniformly ultimately bounded, and the tracking error eventually converges to a small neighborhood around zero. The main advantage of the proposed method is that only one adaptation parameter needs to be updated,which reduces the computational burden significantly. Simulation results demonstrate the feasibility of the proposed scheme and the comparison results show that the improved DSC method can reduce the computational burden by almost two thirds in comparison with the standard DSC method.

Output-feedback Dynamic Surface Control for a Class of Nonlinear Non-minimum Phase Systems

In this paper, an output-feedback tracking controller is proposed for a class of nonlinear non-minimum phase systems.To keep the unstable internal dynamics bounded, the method of output redefinition is applied to let the stability of the internal dynamics depend on that of redefined output, thus we only need to consider the new external dynamics rather than internal dynamics in the process of designing control law. To overcome the explosion of complexity problem in traditional backstepping design, the dynamic surface control(DSC) method is firstly used to deal with the problem of tracking control for the nonlinear non-minimum phase systems. The proposed outputfeedback DSC controller not only forces the system output to asymptotically track the desired trajectory, but also drives the unstable internal dynamics to follow its corresponding bounded and causal ideal internal dynamics, which is solved via stable system center method. Simulation results illustrate the validity of the proposed output-feedback DSC controller.

Adaptive Neural Network Dynamic Surface Control for Perturbed Nonlinear Time-delay Systems

This paper proposes an adaptive neural network control method for a class of perturbed strict-feedback nonlinear systems with unknown time delays. Radial basis function neural networks are used to approximate unknown intermediate control signals. By constructing appropriate Lyapunov-Krasovskii functionals, the unknown time delay terms have been compensated. Dynamic surface control technique is used to overcome the problem of ＂explosion of complexity＂ in backstepping design procedure. In addition, the semiglobal uniform ultimate boundedness of all the signals in the closed-loop system is proved. A main advantage of the proposed controller is that both problems of ＂curse of dimensionality＂ and ＂explosion of complexity＂ are avoided simultaneously. Finally, simulation results are presented to demonstrate the effectiveness of the approach.

Adaptive Fuzzy Dynamic Surface Control for Uncertain Nonlinear Systems

In this paper, a robust adaptive fuzzy dynamic surface control for a class of uncertain nonlinear systems is proposed. A novel adaptive fuzzy dynamic surface model is built to approximate the uncertain nonlinear functions by only one fuzzy logic system. The approximation capability of this model is proved and the model is implemented to solve the problem that too many approximators are used in the controller design of uncertain nonlinear systems. The shortage of ＂explosion of complexity＂ in backstepping design procedure is overcome by using the proposed dynamic surface control method. It is proved by constructing appropriate Lyapunov candidates that all signals of closed-loop systems are semi-globally uniformly ultimate bounded. Also, this novel controller stabilizes the states of uncertain nonlinear systems faster than the adaptive sliding mode controller （SMC）. Two simulation examples are provided to illustrate the effectiveness of the control approach proposed in this paper.

Robust missile autopilot design based on dynamic surface control

Since the dynamical system and control system of the missile are typically nonlinear, an effective acceleration tracking autopilot is designed using the dynamic surface control(DSC)technique in order to make the missile control system more robust despite the uncertainty of the dynamical parameters and the presence of disturbances. Firstly, the nonlinear mathematical model of the tail-controlled missile is decomposed into slow acceleration dynamics and fast pitch rate dynamics based on the naturally existing time scale separation. Secondly, the controller based on DSC is designed after obtaining the linear dynamics characteristics of the slow and fast subsystems. An extended state observer is used to detect the uncertainty of the system state variables and aerodynamic parameters to achieve the compensation of the control law. The closed-loop stability of the controller is derived and rigorously analyzed. Finally, the effectiveness and robustness of the design is verified by Monte Carlo simulation considering different initial conditions and parameter uptake. Simulation results illustrate that the missile autopilot based DSC controller achieves better performance and robustness than the other two well-known autopilots.The method proposed in this paper is applied to the design of a missile autopilot, and the results show that the acceleration tracking autopilot based on the DSC controller can ensure accurate tracking of the required commands and has better performance.

Dynamic Surface Control with Nonlinear Disturbance Observer for Uncertain Flight Dynamic System

A new robust control method of a nonlinear flight dynamic system with aerodynamic coefficients and external disturbance has been proposed.The proposed control system is a combination of the dynamic surface control(DSC)and the nonlinear disturbance observer(NDO).DSC technique provides the ability to overcome the″explosion of complexity″problem in backstepping control.NDO is adopted to observe the uncertainties in nonlinear flight dynamic system.It has been proved that the proposed design method can guarantee uniformly ultimately boundedness of all the signals in the closed-loop system by Lyapunov stability theorem.Finally,simulation results show that the proposed controller provides better performance than the traditional nonlinear controller.

Dynamic Flow Control Strategies of Vehicle SCR Urea Dosing System

Selective Catalyst Reduction（SCR）Urea Dosing System（UDS）directly affects the system accuracy and the dynamic response performance of a vehicle.However,the UDS dynamic response is hard to keep up with the changes of the engine＇s operating conditions.That will lead to low NO_χconversion efficiency or NH_3 slip.In order to optimize the injection accuracy and the response speed of the UDS in dynamic conditions,an advanced control strategy based on an air-assisted volumetric UDS is presented.It covers the methods of flow compensation and switching working conditions.The strategy is authenticated on an UDS and tested in different dynamic conditions.The result shows that the control strategy discussed results in higher dynamic accuracy and faster dynamic response speed of UDS.The inject deviation range is improved from being between-8%and 10%to-4%and 2%and became more stable than before,and the dynamic response time was shortened from 200 ms to 150 ms.The ETC cycle result shows that after using the new strategy the NH_3 emission is reduced by 60%,and the NO_χemission remains almost unchanged.The trade-off between NO_χconversion efficiency and NH_3 slip is mitigated.The studied flow compensation and switching working conditions can improve the dynamic performance of the UDS significantly and make the UDS dynamic response keep up with the changes of the engine＇s operating conditions quickly.

Advances in Active Suspension Systems for Road Vehicles

Active suspension systems(ASSs)have been proposed and developed for a few decades,and have now once again become a thriving topic in both academia and industry,due to the high demand for driving comfort and safety and the compatibility of ASSs with vehicle electrification and autonomy.Existing review papers on ASSs mainly cover dynamics modeling and robust control;however,the gap between academic research outcomes and industrial application requirements has not yet been bridged,hindering most ASS research knowledge from being transferred to vehicle companies.This paper comprehensively reviews advances in ASSs for road vehicles,with a focus on hardware structures and control strategies.In particular,state-of-the-art ASSs that have been recently adopted in production cars are discussed in detail,including the representative solutions of Mercedes active body control(ABC)and Audi predictive active suspension;novel concepts that could become alternative candidates are also introduced,including series active variable geometry suspension,and the active wheel-alignment system.ASSs with compact structure,small mass increment,low power consumption,high-frequency response,acceptable economic costs,and high reliability are more likely to be adopted by car manufacturers.In terms of control strategies,the development of future ASSs aims not only to stabilize the chassis attitude and attenuate the chassis vibration,but also to enable ASSs to cooperate with other modules(e.g.,steering and braking)and sensors(e.g.,cameras)within a car,and even with high-level decision-making(e.g.,reference driving speed)in the overall transportation system-strategies that will be compatible with the rapidly developing electric and autonomous vehicles.

The H_∞ synchronization of nonlinear Bloch systems via dynamic feedback control approach

We consider an H∞ synchronization problem in nonlinear Bloch systems. Based on Lyapunov stability theory and linear matrix inequality formulation, a dynamic feedback controller is designed to guarantee asymptotic stability of the master-slave synchronization. Moreover, this controller reduces the effect of an external disturbance to the H∞ norm constraint. A numerical example is given to validate the proposed synchronization scheme.

Adaptive Synchronization of Rssler System Based on Dynamic Surface Control

A synchronization scheme for R6ssler system based on Dynamic Surface Control （DSC） is proposed in this paper. The DSC method is a recursive design procedure like conventional backstepping methods. Different from the backstepping design, a first-order fdter is introduced in every DSC design step. For this introduced fdter, the derivative of the selected virtual control is avoided and then the drawback of ＂explosion of complexity＂ existing in backstepping design is overcome. Moreover, adaptive method is used for controller design when the system parameters are unknown. Finally, a numerical example is given to illustrate the effectiveness and performance of the proposed method.

Research on Self-balancing Two Wheels Mobile Robot Control System Analysis

The paper presents the research on self-balancing two-wheels mobile robot control system analysis with experimental studies.The research problem in this work is to stabilize the mobile robot with self-control and to carry the sensitive things without failing in a long span period.The main objective of this study is to focus on the mathematical modelling of mobile robot from laboratory scale to real world applications.The numerical expression with mathematical modelling is very important to control the mobile robot system with linearization.The fundamental concepts of dynamic system stability were utilized for maintaining the stability of the constructed mobile robot system.The controller design is also important for checking the stability and the appropriate controller design is proportional,integral,and derivative-PID controller and Linear Quadratic Regulator(LQR).The steady state error could be reduced by using such kind of PID controller.The simulation of numerical expression on mathematical modeling was conducted in MATLAB environments.The confirmation results from the simulation techniques were applied to construct the hardware design of mobile robot system for practical study.The results from simulation approaches and experimental approaches are matched in various kinds of analyses.The constructed mobile robot system was designed and analyzed in the control system design laboratory of Yangon Technological University(YTU).

Temperature distribution and dynamic control of secondary cooling in slab continuous casting

To predict and optimize the temperature distribution of slab continuous casting in steady operational state, a three-dimensional model （named ＂offline model＂） based on the heat transfer and solidification theories was developed. Both heat transfer and flux distribution characteristics of the nozzle sprays on the slab were considered, and the complicated boundary conditions, such as spray cooling, natural convection, thermal radiation as well as contact cooling of individual rolls were involved in the model. By using the calibrated caster dependent model factors, the calculated temperature and shell thickness accorded well with the measured. Furthermore, a dynamic secondary water cooling control system was also developed on the basis of a two-dimensional transient heat transfer model （named ＂online model＂） and incremental PID control algorithm to reduce slab surface temperature fluctuation in unsteady state. Compared with the traditional spray table control method, the present online model and dynamic PID control demonstrate a higher capability and flexibility to adjust cooling water flowrate and reduce slab surface temperature fluctuation when the casting speed is changed.

Adaptive Dynamic Surface Control for Integrated Missile Guidance and Autopilot

Integrated guidance and control for homing missiles utilizing adaptive dynamic surface control approach is considered based on the three channels independence design idea. A time-varying integrated guidance and control model with unmatched uncertainties is first formulated for the pitch channel, and an adaptive dynamic surface control algorithm is further developed to deal with these unmatched uncertainties. It is proved that the proposed feedback controller can ensure not only the accuracy of target interception, but also the stability of the missile dynamics. Then, the same control approach is further applied to the control design of the yaw and roll channels. The 6-degree-of-freedom （6-DOF） nonlinear missile simulation results demonstrate the feasibility and advantage of the proposed integrated guidance and control design scheme.

Dynamics and adaptive control of a dual-arm space robot with closed-loop constraints and uncertain inertial parameters

A dynamics-based adaptive control approach is proposed for a planar dual-arm space robot in the presence of closed-loop constraints and uncertain inertial parameters of the payload. The controller is capable of controlling the po- sition and attitude of both the satellite base and the payload grasped by the manipulator end effectors. The equations of motion in reduced-order form for the constrained system are derived by incorporating the constraint equations in terms of accelerations into Kane＇s equations of the unconstrained system. Model analysis shows that the resulting equations perfectly meet the requirement of adaptive controller design. Consequently, by using an indirect approach, an adaptive control scheme is proposed to accomplish position/attitude trajectory tracking control with the uncertain parameters be- ing estimated on-line. The actuator redundancy due to the closed-loop constraints is utilized to minimize a weighted norm of the joint torques. Global asymptotic stability is proven by using Lyapunov＇s method, and simulation results are also presented to demonstrate the effectiveness of the proposed approach.

Dynamic Feedforward Control of a Novel 3-PSP 3-DOF Parallel Manipulator

Parallel manipulators with less than six degrees of freedom （DOF） have been increasingly used in high-speed hybrid machine tools. The structural features of parallel manipulators are dynamic, a characteristic that is particularly significant when these manipulators are used in high-speed machine tools. However, normal kinematic control method cannot satisfy the requirements of the control system. Many researchers use model-based dynamic control methods, such as the dynamic feedforward control method. However, these methods are rarely used in hybrid machine tools because of the complex dynamic model of the parallel manipulator. In order to study the dynamic control method of parallel manipulators, the dynamic feedforward control method is used in the dynamic control system of a 3-PSP （prismatic-spherical-prismatic） 3-DOF spatial parallel manipulator used as a spindle head in a high-speed hybrid machine tool. Using kinematic analysis as basis and the Newton-Euler method, we derive the dynamic model of the parallel manipulator. Furthermore, a model-based dynamic feedforward control system consisting of both kinematic control and dynamic control subsystems is established. The dynamic control subsystem consists of two modules. One is used to eliminate the influence of the dynamic characteristics of high-speed movement, and the other is used to eliminate the dynamic disturbances in the milling process. Finally, the simulation model of the dynamic feedforward control system of the 3-PSP parallel manipulator is constructed in Matlab/Simulink. The simulations of the control system eliminating the influence of the dynamic characteristics and dynamic disturbances are conducted. A comparative study between the simulations and the normal kinematic control method is also presented.The simulations prove that the dynamic feedforward control method effectively eliminates the influence of the dynamic disturbances and dynamic characteristics of the parallel manipulator on high-speed machine tools, and significantly improves the trajectory accuracy. This is the first attempt to introduce the dynamic feedfordward control method into the 3-PSP spatial parallel manipulator whose dynamic model is complex and provides a study basis for the real-time dynamic control of the high-speed hybrid machine tools.