Dynamic simulation analysis of molten salt reactor-coupled air-steam combined cycle power generation system

A nonlinear dynamic simulation model based on coordinated control of speed and flow rate for the molten salt reactor and combined cycle systems is proposed here to ensure the coordination and stability between the molten salt reactor and power system.This model considers the impact of thermal properties of fluid variation on accuracy and has been validated with Simulink.This study reveals the capability of the control system to compensate for anomalous situations and maintain shaft stability in the event of perturbations occurring in high-temperature molten salt tank outlet parameters.Meanwhile,the control system’s impact on the system’s dynamic characteristics under molten salt disturbance is also analyzed.The results reveal that after the disturbance occurs,the controlled system benefits from the action of the control,and the overshoot and disturbance amplitude are positively correlated,while the system power and frequency eventually return to the initial values.This simulation model provides a basis for utilizing molten salt reactors for power generation and maintaining grid stability.

Dynamic mechanical characteristics of frozen subgrade soil subjected to freeze-thaw cycles

As a widely-applied engineering material in cold regions, the frozen subgrade soils are usually subjected to seismic loading, which are also dramatically influenced by the freeze-thaw(F-T)cycles due to the varying temperature. A series of dynamic cyclic triaxial experiments were conducted through a cryogenic triaxial apparatus for exploring the influences of F-T cycles on the dynamic mechanical properties of frozen subgrade clay.According to the experimental results of frozen clay at the temperature of-10℃, the dynamic responses and microstructure variation at different times of F-T cycles(0, 1, 5, and 20 cycles) were explored in detail.It is experimentally demonstrated that the dynamic stress-strain curves and dynamic volumetric strain curves of frozen clay are significantly sparse after 20F-T cycles. Meanwhile, the cyclic number at failure(Nf) of the frozen specimen reduces by 89% after 20freeze-thaw cycles at a low ratio of the dynamic stress amplitude. In addition, with the increasing F-T cycles,the axial accumulative strain, residual deformation,and the value of damage variable of frozen clay increase, while the dynamic resilient modulus and dynamic strength decrease. Finally, the influence of the F-T cycles on the failure mechanisms of frozen clay was discussed in terms of the microstructure variation. These studies contribute to a better understanding of the fundamental changes in the dynamic mechanical of frozen soils exposed to F-T cycles in cold and seismic regions.

Dynamic behaviors of water-saturated and frozen sandstone subjected to freeze-thaw cycles

In high-altitude cold areas,freeze-thaw(F-T)cycles induced by day-night and seasonal temperature changes cause numerous rock mass slope engineering disasters.To investigate the dynamic properties of rock in the natural environment of a high-altitude cold area,standard specimens were drilled from the slope of the Jiama copper mine in Tibet,and dynamic compression tests were performed on watersaturated and frozen sandstone with different numbers of F-T cycles(0,10,20,30,and 40)by the split Hopkinson pressure bar(SHPB)system with a cryogenic control system.The influence of water-saturated and frozen conditions on the dynamic performance of sandstone was investigated.The following conclusions are drawn:(1)With increasing strain rate,the attenuation factor(la)of water-saturated sandstone and the intensifying factor(li)of frozen sandstone linearly increase.As the number of F-T cycles increases,the dependence factor(ld)of water-saturated sandstone linearly decreases,whereas the ld of frozen sandstone linearly increases.(2)The prediction equation of the dynamic compressive strength of water-saturated and frozen sandstone is obtained,which can be used to predict the dynamic compressive strength of sandstone after various F-T cycles based on the strain rate.(3)The mesoscopic mechanism of water-saturated and frozen sandstone’s dynamic compressive strength evolution is investigated.The water softening effect causes the dynamic compressive strength of water-saturated sandstone to decrease,whereas the strengthening effect of pore ice causes it to increase.(4)The decrease in the relative dynamic compressive strength of water-saturated sandstone and the increase in the relative dynamic compressive strength of frozen sandstone can be attributed to the increased porosity.

Optimal Dynamic Voltage Restorer Using Water Cycle Optimization Algorithm

This paper proposes a low complexity control scheme for voltage control of a dynamic voltage restorer(DVR)in a three-phase system.The control scheme employs the fractional order,proportional-integral-derivative(FOPID)controller to improve on the DVR performance in order to enhance the power quality in terms of the response time,steady-state error and total harmonic distortion(THD).The result obtained was compared with fractional order,proportionalintegral(FOPI),proportional-integral-derivative(PID)and proportional-integral(PI)controllers in order to show the effectiveness of the proposed DVR control scheme.A water cycle optimization algorithm(WCA)was utilized to find the optimal set for all the controller gains.They were used to solve four power quality issues;balanced voltage sag,balanced voltage swell,unbalanced voltage sag,and unbalanced voltage swell.It showed that one set of controller gain obtained from the WCA could solve all the power quality issues while the others in the literature needed an individual set of optimal gain for each power quality problem.To prove the concept,the proposed DVR algorithm was simulated in the MATLAB/Simulink software and the results revealed that the four optimal controllers can compensate for all the power quality problems.A comparative analysis of the results in various aspects of their dynamic response and%THD was discussed and analyzed.It was found that PID controller yields the most rapid performance in terms of average response time while FOPID controller yields the best performance in term of average%steady-state error.FOPI controller was found to provide the lowest THD percentage in the average%THD.FOPID did not differ much in average response from the PID and average%THD from FOPI;however,FOPID provided the most outstanding average steady-state error.According to the CBMA curve,the dynamic responses of all controllers fall in the acceptable power quality area.The total harmonic distortion(THD)of the compensated load voltage from all the controllers were within the 8%limit in accordance to the IEEE std.519-2014.

Predicting dynamic compressive strength of frozen-thawed rocks by characteristic impedance and data-driven methods

In cold regions,the dynamic compressive strength(DCS)of rock damaged by freeze-thaw weathering significantly influences the stability of rock engineering.Nevertheless,testing the dynamic strength under freeze-thaw weathering conditions is often both time-consuming and expensive.Therefore,this study considers the effect of characteristic impedance on DCS and aims to quickly determine the DCS of frozen-thawed rocks through the application of machine-learning techniques.Initially,a database of DCS for frozen-thawed rocks,comprising 216 rock specimens,was compiled.Three external load parameters(freeze-thaw cycle number,confining pressure,and impact pressure)and two rock parameters(characteristic impedance and porosity)were selected as input variables,with DCS as the predicted target.This research optimized the kernel scale,penalty factor,and insensitive loss coefficient of the support vector regression(SVR)model using five swarm intelligent optimization algorithms,leading to the development of five hybrid models.In addition,a statistical DCS prediction equation using multiple linear regression techniques was developed.The performance of the prediction models was comprehensively evaluated using two error indexes and two trend indexes.A sensitivity analysis based on the cosine amplitude method has also been conducted.The results demonstrate that the proposed hybrid SVR-based models consistently provided accurate DCS predictions.Among these models,the SVR model optimized with the chameleon swarm algorithm exhibited the best performance,with metrics indicating its effectiveness,including root mean square error(RMSE)﹦3.9675,mean absolute error(MAE)﹦2.9673,coefficient of determination(R^(2))﹦0.98631,and variance accounted for(VAF)﹦98.634.This suggests that the chameleon swarm algorithm yielded the most optimal results for enhancing SVR models.Notably,impact pressure and characteristic impedance emerged as the two most influential parameters in DCS prediction.This research is anticipated to serve as a reliable reference for estimating the DCS of rocks subjected to freeze-thaw weathering.

Improved Diurnal Cycle of Precipitation on Land in a Global Non-Hydrostatic Model Using a Revised NSAS Deep Convective Scheme

In relatively coarse-resolution atmospheric models,cumulus parameterization helps account for the effect of subgridscale convection,which produces supplemental rainfall to the grid-scale precipitation and impacts the diurnal cycle of precipitation.In this study,the diurnal cycle of precipitation was studied using the new simplified Arakawa-Schubert scheme in a global non-hydrostatic atmospheric model,i.e.,the Yin-Yang-grid Unified Model for the Atmosphere.Two new diagnostic closures and a convective trigger function were suggested to emphasize the job of the cloud work function corresponding to the free tropospheric large-scale forcing.Numerical results of the 0.25-degree model in 3-month batched real-case simulations revealed an improvement in the diurnal precipitation variation by using a revised trigger function with an enhanced dynamical constraint on the convective initiation and a suitable threshold of the trigger.By reducing the occurrence of convection during peak solar radiation hours,the revised scheme was shown to be effective in delaying the appearance of early-afternoon rainfall peaks over most land areas and accentuating the nocturnal peaks that were wrongly concealed by the more substantial afternoon peak.In addition,the revised scheme enhanced the simulation capability of the precipitation probability density function,such as increasing the extremely low-and high-intensity precipitation events and decreasing small and moderate rainfall events,which contributed to the reduction of precipitation bias over mid-latitude and tropical land areas.

Valve Dynamic and Thermal Cycle Model in Stepless Capacity Regulation for Reciprocating Compressor

The existing researches of stepless capacity regulation system by depressing the suction valve for reciprocation compressor always adopt hypothesis that the compressor valves are open or close instantaneously, the valve dynamic has not been taken account into thermal cycle computation, the influence of capacity regulation system on suction valves dynamic performance and cylinder thermal cycle operation has not been considered. This paper focuses on theoretical and experimental analysis of the valve dynamic and thermal cycle for reciprocating compressor in the situation of stepless capacity regulation. The valve dynamics equation, gas forces for normal and back flow, and the cylinder pressure varying with suction valve unloader moment during compression thermal cycle are discussed. A new valve dynamic model based on L-K real gas state equation for reciprocating compressor is first deduced to reduce the calculation errors induced by the ideal gas state equation. The variations of valve dynamic and cylinder pressure during part of compression stroke are calculated numerically. The calculation results reveal the non-normal thermal cycle and operation condition of compressor in stepless capacity regulation situation. The numerical simulation results of the valve dynamic and thermal cycle parameters are also verified by the stepless capacity regulation experiments in the type of 3L-10/8 reciprocating compressor. The experimental results agree with the numerical simulation results, which show that the theoretical models proposed are effective and high-precision. The proposed theoretical models build the theoretical foundation to design the real stepless capacity regulation system.

Experimental study of dynamic resilient modulus of subgrade soils under coupling of freeze–thaw cycles and dynamic load

Although the dynamic properties of subgrade soils in seasonally frozen areas have already been studied, few researchers have considered the influence of shallow groundwater during the freeze–thaw(F–T) cycles. So a multifunctional F–T cycle system was developed to imitate the groundwater recharge in the subgrade during the freezing process and a large number of dynamic triaxial experiments were conducted after the F–T cycles. Some significant factors including the F–T cycle number, compaction degree, confining pressure, cyclic deviator stress, loading frequency, and water content were investigated for the resilient modulus of soils. The experimental results indicated that the dynamic resilient modulus of the subgrade was negatively correlated with the cyclic deviator stress, F–T cycle number, and initial water content, whereas the degree of compaction, confining pressure, and loading frequency could enhance the resilient modulus. Furthermore, a modified model considering the F–T cycle number and stress state was established to predict the dynamic resilient modulus. The calculated results of this modified model were very close to the experimental results. Consequently, calculation of the resilient modulus for F–T cycles considering the dynamic load was appropriate. This study provides reference for research focusing on F–T cycles with groundwater supply and the dynamic resilient moduli of subgrade soils in seasonally frozen areas.

Dynamic grey model of verification cycle and lifecycle of measuring instrument and its application

Two dynamic grey models DGM (1, 1) for the verification cycle and the lifecycle of measuring instrument based on time sequence and frequency sequence were set up, according to the statistical feature of examination data and weighting method. By a specific case, i.e. vernier caliper, it is proved that the fit precision and forecast precision of the models are much higher, the cycles are obviously different under different working conditions, and the forecast result of the frequency sequence model is better than that of the time sequence model. Combining dynamic grey model and auto-manufacturing case the controlling and information subsystems of verification cycle and the lifecycle based on information integration, multi-sensor controlling and management controlling were given. The models can be used in production process to help enterprise reduce error, cost and flaw.

GPS dynamic cycle slip detection and correction with baseline constraint

When the cycle slips take place in the attitude determination of a moving platform, the precision of the attitude will be impaired badly. A method of cycle slip detection and correction is proposed, which is suitable to the dynamic measurement using GPS carrier phase： the cycle slips detection is first achieved by triple difference observables, then the cycle slips correction is performed with baseline length constraint. The simulation results show that the proposed method is effective to the dynamic cycle slips problem.

A model study on carbon cycle and phytoplankton dynamical processes in the Bohai Sea

The carbon cycle of lower trophic level in the Bohai Sea is studied with a three-dimensional biological and physical coupled model. The influences of the processes (including horizontal advection, river nutrient load, active transport etc. ) on the phytoplankton biomass and its evolution are estimated. The Bohai Sea is a weak sink of the CO2 in the atmosphere. During the cycle, 13.7% of the gross production of the phytoplankton enter the higher trophic level and 76.8 % of it are consumed by the respiration itself. The nutrient reproduction comes mainly from the internal biogeochemical loop and the rem-ineralization is an important mechanism of the nutrient transfer from organic form to inorganic. Horizontal advection decreases the total biomass and the eutrophication in some sea areas. Change in the nutrient load of a river can only adjust the local system near its estuary. Controlling the input of the nutrient, which limits the alga growth, can be very useful in lessening the phytoplankton biomass.

EFFECT OF DYNAMIC STRAIN AGING ON LOW CYCLE FATIGUE BEHAVIOUR OF 18-8 AUSTENITIC STAINLESS STEEL

Studies were made of the symmetric tensile-compressive low cycle fatigue behaviour and the influence of dynamic strain aging(DSA)pre-treatment of 18-8 austenitic stainless steel. Within the testing amplitude range of strain.±0.5 % to±1.5 %,the three processes of cyclic hardening,cyclic saturation and cyclic softening were observed.In the same amplitude of strain,the peak stress of the samples pre-treated by DSA is higher than that of solid-solu- tion and cold working pre-treatment,but no remarkable differences of the fatigue lives of them were found.TEM observation shows that the uniform and stable dislocation networks with high density form after DSA pre-treatment,which increases the cyclic peak stress.The cyclic softening results from the low dislocation density and elongated cell structure with low energy.

Dynamic test on waste heat recovery system with organic Rankine cycle

Dynamic performance is important to the controlling and monitoring of the organic Rankine cycle(ORC) system so to avoid the occurrence of unwanted conditions. A small scale waste heat recovery system with organic Rankine cycle was constructed and the dynamic behavior was presented. In the dynamic test, the pump was stopped and then started. In addition, there was a step change of the flue gas volume flow rate and the converter frequency of multistage pump, respectively. The results indicate that the working fluid flow rate has the shortest response time, followed by the expander inlet pressure and the expander inlet temperature.The operation frequency of pump is a key parameter for the ORC system. Due to a step change of pump frequency(39.49-35.24 Hz),the expander efficiency and thermal efficiency drop by 16% and 21% within 2 min, respectively. Besides, the saturated mixture can lead to an increase of the expander rotation speed.

Fracture Behavior of CrN Coatings Under Indentation and Dynamic Cycle Impact

Fracture behavior of CrN coatings deposited on the surface of silicon and AISI52100 steel by different energy ion beam assisted magnetron sputtering technique （IBAMS） was studied using indentation and dynamic cycle impact. It is found that, for the coatings on silicon substrate, the cracks form in the indentation corners and then propagate outward under Vickers indentation. The coating prepared using ion assisted energy of 800 eV shows the highest fracture resistance due to its compact structure. Under Rockwell indentation, only finer radial cracks are found in the CrN coating on AISI 52100 steel without ion assisting while in the condition of ion assisting energy of 800 eV, radial, lateral cracks and spalling appear in the vicinity of indentation. The fracture of CrN coatings under dynamic cycle impact is similar to fatigue. The impact fracture resistance of CrN coatings increases with the increase of ion assisting energy.

Dynamic pursuing ecological model concerning the nitrogen cycle in the environment of Chinese mainland

The paper gives a special dynamic pursuing ecological model on the bio-geochemical cycle of nitrogen in the whole range 9.6 million square kilometers of Chinese mainland, basing on the reservoir-content and flux-rate of nitrogen and among the four spheres: atmosphere, pedosphere, biosphere, and hydrosphere, and the law of bio-geochemical cycle of nitrogen, the model predicted the size of reservoir capacities and fluxes of nitrogen in each sphere. Through tested and verified, the model was proven reasonable and reliable.

A Dynamic Programming Approach for the Max-Min Cycle Packing Problem in Even Graphs

Let be an undirected graph. The maximum cycle packing problem in G then is to find a collection of edge-disjoint cycles Ciin G such that s is maximum. In general, the maximum cycle packing problem is NP-hard. In this paper, it is shown for even graphs that if such a collection satisfies the condition that it minimizes the quantityon the set of all edge-disjoint cycle collections, then it is a maximum cycle packing. The paper shows that the determination of such a packing can be solved by a dynamic programming approach. For its solution, an-shortest path procedure on an appropriate acyclic networkis presented. It uses a particular monotonous node potential.

Research on Ecological Assessment and Dynamic Optimization of Energy-saving and New Energy Vehicle Business Model Based on Full Life Cycle Theory

The rapid development of China’s automobile industry has brought ever-increasing impact on resources,energy and environment,the energy-saving and new energy vehicles come into being accordingly.This article firstly systematically introduces the technical route of energy-saving and new energy vehicles of China,focusing on the key bottleneck problems arising from the construction process of current assessment system of the technical route for energy-saving and new energy vehicles,establishes the energy-saving and new energy vehicle business model assessment index system afterward based on the comparative analysis on energy-saving and new energy vehicle business assessment model and the full life cycle theory,and finally makes prospects and forecasts on vital problems of system boundary,dynamic optimization,simulation system of full life cycle assessment of energy-saving and new energy vehicle.

Dynamic Quantity Theory of Money:Research on Monetary Cycle and Business Cycle Based on the Concepts of Issuing Money and Operating Money

The Quantity Theory of Money and the Theory of Credit Creation have been the major streams in the study of the quantity of money.Nowadays,monetary theory is dominated by the Quantity Theory of Money because the Monetarist School and the Rational Expectation School are both the advocates of the Quantity Theory of Money,which has resulted in a sharp decrease of scholars studying the Theory of Credit Creation.Nevertheless,the two theories will ultimately converge.Given that reason,we propose a new theory-Dynamic Quantity Theory of Money in this paper,by which the unification of the Quantity Theory of Money and the Theory of Credit Creation can be achieved.Based on the Dynamic Quantity Theory of Money,we further put forward the Theory of Money Operation Cycle,the Theory of Monetary Compensation and Theory of Investment Compensation targeting economic crises,expound why Quantitative Easing monetary policy fails and why Quantitative Easing does not cause inflation in the short term under the premise of these theories,and demonstrate the necessity of fiscal investment for rescuing economic crisis from the perspective of theories of money.

High-resolution spatiotemporal mapping:a comprehensive view of eukaryotic cell cycle proteome dynamics

In a recent study published in Cell,Litsios et al.revealed a highresolution spatiotemporal map of the eukaryotic cell cycle proteome.1 They identified proteome-level changes in both abundance and spatial distribution throughout the cell cycle and provided a valuable resource for future exploration into the global proteome dynamics that drive cell cycle progression(https://thecellvision.org/cellcycle).

Microscopic damage and dynamic mechanical properties of rock under freeze-thaw environment

For understanding the rock microscopic damage and dynamic mechanical properties subjected to recurrent freeze-thaw cycles, experiments for five groups of homogeneous sandstone under different freeze-thaw cycles were conducted. After freezethaw, nuclear magnetic resonance(NMR) tests and impact loading tests were carried out, from which microscopic damage characteristics of sandstone and dynamic mechanical parameters were obtained. The results indicate that the porosity increases with the increase of cycle number, the rate of porosity growth descends at the beginning of freeze-thaw, yet accelerates after a certain number of cycles. The proportion of pores with different sizes changes dynamically and the multi-scale distribution of pores tends to develop on pore structure with the continuing impact of freeze-thaw and thawing. Dynamic compressive stress-strain curve of sandstone undergoing freeze-thaw can be divided into four phases, and the phase of compaction is inconspicuous compared with the static curve. Elastic modulus and dynamic peak intensity of sandstone gradually decrease with freeze-thaw cycles, while peak strain increases. The higher the porosity is, the more serious the degradation of dynamic intensity is. The porosity is of a polynomial relationship with the dynamic peak intensity.