Application of strength reduction method to dynamic anti-sliding stability analysis of high gravity dam with complex dam foundation

Considering that there are some limitations in analyzing the anti-sliding seismic stability of dam-foundation systems with the traditional pseudo-static method and response spectrum method, the dynamic strength reduction method was used to study the deep anti-sliding stability of a high gravity dam with a complex dam foundation in response to strong earthquake-induced ground action. Based on static anti-sliding stability analysis of the dam foundation undertaken by decreasing the shear strength parameters of the rock mass in equal proportion, the seismic time history analysis was carried out. The proposed instability criterion for the dynamic strength reduction method was that the peak values of dynamic displacements and plastic strain energy change suddenly with the increase of the strength reduction factor. The elasto-plastic behavior of the dam foundation was idealized using the Drucker-Prager yield criterion based on the associated flow rule assumption. The result of elasto-plastic time history analysis of an overflow dam monolith based on the dynamic strength reduction method was compared with that of the dynamic linear elastic analysis, and the reliability of elasto-plastic time history analysis was confirmed. The results also show that the safety factors of the dam-foundation system in the static and dynamic cases are 3.25 and 3.0, respectively, and that the F2 fault has a significant influence on the anti-sliding stability of the high gravity dam. It is also concluded that the proposed instability criterion for the dynamic strength reduction method is feasible.

Simplified Full Dynamic Analysis of a Railway Tunnel in Ethiopia

This paper presents an effective means of analyzing the safety of a tunnel under dynamic loading in areas with seismic records. A particular case of the railway tunnel in the earthquake-prone regions of the escarpment seismic zone of Ethiopia was the specific focus area of the research. Probabilistic seismic hazard analysis (PSHA) and deaggregation have been conducted to determine the design earthquake required as an input for the dynamic analysis. The PSHA performed by considering the operating design earthquake with conservative assumptions of the local geological features resulted in a peak ground acceleration of 0.36. Two pairs of design earthquake have been obtained from the deaggregation process, which were used to filter acceleration time histories for the selected design earthquake from the ground motion database of Pacific Earthquake Engineering Research Center. Finally, full dynamic analyses of the tunnel have been performed by applying the scaled acceleration time histories corresponding to the structure in the specific site. It was demonstrated how to prove the stability of the tunnel located in difficult ground conditions by performing plane strain analyses with the possible minimum computational efforts.

On the Dynamic Behavior of Town Gas Pipelines

Pipelines have been acknowledged as the most reliable, economic and efficient means for the transportation of gas and other commercial fluids such as oil and water. The designation of pipeline system as “lifelines” signifies that their operation is essential in maintaining the public safety and well being. A pipeline transmission system is a linear system which traverses a large geographical area, and soil conditions thus, is susceptible to a wide variety of hazards. This pa-per is concerned with the dynamic behavior of buried town gas pipelines. A computer model with a finite number of nodes is created to simulate the behavior of the real gas pipeline. The dynamic susceptibility method is applied for twenty mode shapes of this model, which utilizes the stress per velocity method and is an incisive analytical tool for screening the vibration modes of the system. It can be readily identified, which modes, if excited, could potentially cause large dynamic stresses. This paper discusses also two of the piping dynamic analyses, namely the effect of the response spectrum of an earthquake and the time history analysis of a truck crosses the pipeline.

Earthquake Analysis for the System of RC Building with a Steel Tower

A steel tower topping an RC building comprises a non-proportional damping structural sys- tem with different damping ratios. To compare the results from the non-proportional damping model and the equivalent damping model.the structural system was calculated with the two damping mod- els during earthquake respectively, using earthquake time history analysis computer program devel- oped by the authors. Differences in the calculated results of inner forces and displacements using the two damping models were observed. It is found that if the equivalent damping model is used in design, the consequence will be unsafe for the steel tower and too safe for the RC building at the same time.

Seismic Analysis for Rigid-Framed Prestressed Reinforced Concrete Bridge in Tianjin Light Railway

The seismic analysis of a rigid-framed prestressed concrete bridge in Tianjin Light Railway is performed. A 3-D dynamic finite element model of the bridge is established considering the weakening effect caused by the soft soil foundation. After the dynamic characteristics are calculated in terms of natural frequencies and modes, the seismic analysis is carried out using the modal response spectrum method and the time-history method, respectively. Based on the calculated results, the reasonable design values are finally suggested as the basis of the seismic design of the bridge, and meanwhile the problems encountered were also analyzed. Finally, some conclusions are drawn as: 1) Despite the superiority of rigid-framed prestressed concrete bridge, the upper and lower ends of the piers of the bridge are proved to be the crucial parts of the bridge, which are easily destroyed under designed earthquake excitations and should be carefully analyzed and designed; 2) The soft soil foundation can possibly result in rather weakening of the lateral rigidity of the rigid-framed bridge, and should be paid considerable attention; 3) The modal response spectrum method, combined with time-history method, is suggested for the seismic analysis in engineering design of the rigid-framed prestressed concrete bridge.

附设黏滞阻尼器的RC框架结构抗震韧性评估

为研究黏滞阻尼器对钢筋混凝土(reinforced concrete,RC)框架结构抗震韧性影响,基于增量动力时程分析方法,对附设黏滞阻尼器的RC框架结构开展抗震韧性能力评估。结合FEMA P-58以及我国抗震韧性评价标准,将主要受损构件的修复费用、修复时间曲线以及易损性信息按实际情况进行相应修正,并对无控结构和有控结构的修复费用、修复时间和人员伤亡等主要抗震韧性指标进行对比分析,明确了黏滞阻尼器对RC框架结构抗震韧性的影响。研究表明,在RC框架结构中适当设置黏滞阻尼器不仅能够减小结构地震响应、降低结构破坏概率,还能有效提升结构抗震韧性。

某高层木混合结构抗震分析与性能测试

木混凝土混合结构在多高层木结构建筑中应用广泛,但此类结构的整体抗震性能以及楼盖动力特性有待研究。本文以江苏省康复医院医技楼为例,应用反应谱法与弹性时程分析法分别开展木混合结构的抗震性能分析,并对局部正交胶合木(CLT)楼盖通过原位测试,开展力学性能、动力特性以及人致振动研究。结果表明:结构抗震指标符合规范要求;CLT楼盖荷载位移关系呈双折线,挠度、应力理论计算时,建议板两端按简支考虑;CLT楼盖竖向自振频率均值约15.49 Hz,满足建筑楼盖限值要求,但在单人快走、单人小跑以及多人随机人致振动工况下,楼盖的峰值加速度偏大,应考虑增加现浇建筑面层,改善纯CLT楼盖舒适度不足的问题。可见,木混合结构通过设计可满足抗震要求,但轻质楼盖应注意舒适度构造措施。

基于地下结构整体损伤表征的复合地震动参数构造及其性能验证

在地下结构抗震设计中,不同的输入地震动引起的地下结构响应有显著差异,因此,合理通过地震动参数选择输入地震动是正确开展地下结构抗震设计的重要前提。针对单一地震动参数难以表征地下结构地震动潜在破坏势问题,文章构造了能更好表征地下结构损伤破坏的复合地震动参数。具体开展了以下工作:提出基于变形与滞回耗能的地下结构整体损伤指标作为结构需求参数,以定量化评估地下结构的整体破坏状态。选取64条真实地震动记录作为输入地震动,开展四层三跨地铁车站地震弹塑性动力时程分析。基于分析结果提供的数据样本,采用偏最小二乘法从统计角度构造复合地震动参数。最后,选用100条真实地震动记录开展两层三跨地铁车站弹塑性动力时程分析,对文章所构造的复合地震动参数进行验证。对比分析复合地震动参数、12个常用地震动参数与地下结构整体损伤指数的回归统计特征。结果表明:复合地震动参数与结构需求数之间具有更好拟合优度值,其Pearson相关性、有效性也优于单一地震动参数。

地下管廊抗震研究现状综述

针对地下管廊工程建设高速发展、抗震减灾需求愈发凸显的现状,综述地下管廊抗震研究现状.首先,通过国内外以往的震害实例,对地下管廊的震害形式、震害影响因素及震害机理进行了系统性总结.其次,从拟静力试验和振动台试验两个方面总结了地下管廊抗震性能的试验研究现状.再次,总结了地下管廊抗震分析的简化分析方法、动力时程方法、地震易损性评估及减隔震技术的研究现状.最后,基于文献综述提出了目前地下管廊抗震研究亟待解决的问题并做出展望,以期促进地下管廊抗震研究的发展.研究表明:地下管廊在地震作用下的破坏形式主要有混凝土剥落、裂缝贯通、接缝错位或张开、管廊受剪断裂等;地震作用下地下管廊穿越非均匀场地时动力响应的放大效应显著,地下管廊穿越软硬交互等非均匀场地时的抗震性能研究值得重视;交叉节点是地下管廊的薄弱环节,交叉管廊的抗震设计方法研究值得关注;预制管廊接头易受到地震破坏,不同类型预制管廊接头的抗震性能研究需深入探索;城市大型地下管廊系统抗震性能受到不同交叉节点和不同管廊之间的交互影响,高效的地下管廊系统建模方法和高效的简化分析方法亟待研究;城市大型地下管廊系统地震易损性分析是重要的发展方向;地下管廊的减隔震技术值得发展.

节点域承载力对半刚性钢框架地震易损性影响研究

目的 通过考察节点域承载力变化与地震易损性曲线间的关系,获得半刚性钢框架地震易损性曲线,量化节点域屈服承载力对半刚性钢框架地震易损性的影响。方法 采用OpenSEES抗震分析软件建立以节点域承载力比为主要参数的半刚性钢框架模型,通过地震需求分析和抗震能力分析,绘制不同节点域屈服承载力比(0.5~1.0)对应的半刚性钢框架地震易损性曲线。结果 节点域屈服承载力比的取值为0.7时,半刚性钢框架地震易损性曲线在四种极限状态下均小于其他半刚性钢框架,且形成包络趋势。结论 在水平地震作用下,允许节点域屈服,可显著降低钢框架的失效概率,结构的抗震性能也得到了明显改善;节点域屈服承载力比取0.7时,结构抗震性改善效果最显著。

双向地震作用下崩塌堆积体边坡动力模糊可靠性分析

考虑崩塌堆积体边坡岩土体参数随机性和模糊性,以及地震力双向性,建立一种边坡地震动力模糊可靠度计算方法,针对竖向地震力对崩塌堆积体边坡稳定可靠性的影响进行进一步研究。首先,选用动力有限元时程分析法计算出双向地震工况下崩塌堆积体边坡的响应特征,并运用模糊理论对强度参数进行模糊性处理;然后,根据Mohr-Coulumb强度准则构建边坡安全系数与可靠度的时程计算模型;最后,采用边坡地震可靠性评价新方法,通过MATLAB编写相应程序,实现计算和分析结果的快速输出。案例结果表明:新方法计算结果更加合理,对工程而言也更加安全;竖向地震作用均对崩塌堆积体边坡整体可靠性存在影响,但影响程度需根据工程实际情况进行分析。在算例工况下,竖向地震对崩塌堆积体边坡的可靠性影响很小,仅使得可靠度降低3.55%,因此,可仅考虑水平地震的影响。

考虑SSI效应的带地下室RC框架结构抗震性能研究

土-结构相互作用效应(Soil-Structure Interaction,SSI)是带地下室钢筋混凝土(Reinforced Concrete,RC)框架结构抗震性能分析的重要因素。基于模态和动力时程分析,通过有限元分析软件系统探究了地下室顶板嵌固、基础顶面嵌固和考虑SSI效应地下室周围土体嵌固等3种不同嵌固方式的RC框架结构抗震性能。结果表明:考虑SSI效应带地下室RC框架结构的自振周期明显延长,其中心柱剪力、各层加速度和层间位移角均有所减小;基础顶面嵌固模型未考虑SSI效应,其计算结果较为保守;SSI效应对带地下室RC框架结构会产生较大的减震影响。

远场水下爆炸冲击作用下重力坝动力稳定性的简化时程分析方法

高坝大库的抗爆与防护是国防安全的重要研究课题。该文针对远场水下爆炸冲击作用下混凝土重力坝的稳定安全评价问题,研究了远场水下爆炸冲击波的传播及其与坝体的相互作用过程;基于波动理论和平面波假设,建立了重力坝爆炸动应力场的简化理论计算模型,最终建议了一种远场水下爆炸冲击波作用下重力坝动力稳定性的简化时程分析方法;同时结合工程实际,采用该方法对某混凝土重力坝的动力稳定性进行了分析。结果表明:在远场爆炸冲击荷载作用下,重力坝的稳定安全系数呈现出先增后减再增并最终保持恒定的变化规律;下游坝面反射形成的拉伸波与剪切波的共同作用是导致建基面稳定安全系数降低的主要原因。

矩形钢管混凝土束风机塔筒风振特性研究

随着风电资源优势区开发逐渐饱和,风电开发的重心开始向风资源条件相对恶劣的低风速地区转移,分布式、大功率、高塔筒和长叶片已经成为风电行业发展趋势。基于此提出了一种新型的矩形钢管混凝土束风机塔筒,该塔筒由矩形钢管混凝土束拼接而成,具有强度高、刚度大和耗能能力强的优点。为研究该塔筒结构的风振响应特性,选用Kaimal脉动风速功率谱,采用谐波合成法模拟风荷载时程曲线,对其进行了动力时程分析,并计算了风振系数及等效静力风荷载。结果表明:该新型塔筒在额定风速下位移塔顶位移最大值为911.84 mm,对应的水平位移角为1/154,符合规范要求。塔筒各构件的强度较好,且具有较大的安全富余度。基于位移等效的阵风荷载因子法计算得到的风振系数值较低;在惯性风荷载法计算得到的等效静力风荷载作用下,结构位移、基底剪力与结构随机振动分析得到的基本一致。

滑坡涌浪作用下弧形闸门动力响应数值分析

库岸滑坡是一种常见的地质灾害,滑坡体入库后诱发的涌浪可能会严重威胁库区内闸门结构稳定性。针对弧形钢闸门在滑坡涌浪作用下的动力响应问题,以某深孔弧形工作闸门为例,通过自编有限元程序模拟滑坡涌浪过程,将计算出的涌浪动水压力转化为闸门的节点荷载,基于动力时程法得到闸门动力响应,并结合闸门静力计算结果进行对比分析。结果表明,在滑坡涌浪作用下,主梁后翼缘和竖梁后翼缘的应力响应最大,闸门各个构件中支臂的位移响应最大;相比于正常蓄水位时的滑坡涌浪,死水位时的滑坡涌浪对闸门结构应力和位移响应的影响更大。

多自由度结构-串并联调谐质量阻尼器减震性能

针对提出的串并联调谐质量阻尼器(TTMD)减震系统,采用粒子群算法,在频域内对多自由度结构⁃TTMD系统进行优化分析。建立多自由度结构⁃TTMD系统减震控制仿真分析模型,分别考虑不同类型实际地震记录,在时域内研究了TTMD对结构地震响应的控制效率,并与相同总质量比的调谐质量阻尼器(TMD)进行比较。进一步考虑了结构刚度发生10%和30%退化的情况,分析了TTMD系统对刚度退化结构的减震效果。数值结果表明,TTMD系统减震性能和鲁棒性能优于TMD系统,且具有阻尼需求小、安装简单、易于实现等优势,是一种增强型减震系统。

不同水头下深孔弧形工作闸门地震响应分析研究

水工钢闸门被广泛应用于我国西南地震高烈度地区。为了确保在脉动水流与地震荷载作用下的安全可靠运行,需要分析不同水头下闸门的抗震性能。采用ANSYS建立三峡大坝某深孔弧形工作闸门有限元模型,基于动力时程法,对其开展地震响应分析,研究闸门在无水、20 m、40 m、60 m和85 m水头下动水压力与地震荷载对闸门强度、刚度的耦合影响。结果表明:水头越高,闸门在有、无动水时的最大应力及主横梁径向位移差值越大,动水压力对闸门的地震响应影响越显著。该研究对于同类水工钢闸门的地震响应分析具有参考借鉴意义。

高层装配整体式剪力墙结构动力弹塑性时程分析

为了研究某高层建筑的抗震性能,对高层装配整体式剪力墙结构动力弹塑性时程进行分析。利用ABAQUS有限元软件,构建高层装配整体式剪力墙结构动力弹塑性材料本构关系有限元模型,模拟地震作用下高层装配整体式剪力墙结构动力时程变化情况。分析结果表明:整体剪力墙结构前6阶振型每两阶平动振型出现一个扭转,且计算结果符合规定,测试剪力墙时程位移变化结构也符合相关规定。随着地震波加载时间的增长,高层装配整体式剪力墙结构受拉损伤逐渐严重。加载至40s时,该结构的混凝土材料已经不能发挥作用,只能依靠钢筋支撑,但未出现明显坍塌,剪力墙结构受压损伤主要出现在剪力墙结构的连接位置,未出现明显受压损伤。说明该高层装配整体式剪力墙结构抗震性能良好。

某高层剪力墙结构的地震响应分析

为研究高层结构在地震作用下的抗震性能,文中以某15层高层剪力墙结构为主要研究对象,利用ABAQUS有限元软件,构建了有限元模型,并进行模态分析与动力时程研究,通过输入3条8度罕遇强度等级的地震波作用,确定了结构在大地震影响下的震害动力响应,得出其最大层间位移角在规范限值以内,结构满足大震不倒的抗震设防要求,以此确定结构的可靠性。

约束砌体结构抗震加固研究

为研究约束砌体结构在采用混凝土条带、窗下墙设缝、窗间墙宽度增大等加固方法作用下的破坏模式,该文以2层开洞砌体结构为研究对象,采用数值模拟技术,建立多组试验模型,研究了条带配筋率、窗下墙设缝深度、窗间墙宽度在动力时程作用下对约束砌体结构抗震性能及自振周期的影响,并以墙体破坏率为指标,定量研究了条带配筋率、窗下墙设缝深度、窗间墙墙体宽度等单因素下的合理取值,研究表明:窗间墙宽度的合理取值应大于900 mm;混凝土条带的钢筋配筋率合理取值为大于0.65%;窗下墙设缝深度的合理取值为200 mm。