In the present work,the turbulent mixing process of a polydisperse quartz particle flow with a plasma stream generated by a radio-frequency(RF)inductively coupled plasma torch was numerically studied.The thermobaric s...In the present work,the turbulent mixing process of a polydisperse quartz particle flow with a plasma stream generated by a radio-frequency(RF)inductively coupled plasma torch was numerically studied.The thermobaric stress in the quartz particles under dynamic heating in a heterogeneous plasma flow was determined by a two-stage approximation approach.The effect of the presence of vacuoles in natural quartz on the particle thermobaric destruction conditions was studied.It was found that the equivalent thermal and baric stresses in quartz particles may significantly increase in the presence of vacuoles within a small gas volume fraction.The influence of the regime and energetic working conditions of an RF inductively coupled plasma torch system on the particle thermobaric destruction conditions was examined,and a recommendation was given to promote the degree of thermobaric destruction of quartz particles,which is of substantial importance for improving the overall enrichment efficiency of quartz concentrates.展开更多
Numerical simulation of turbulent mixing process of polydisperse quartz particle(particle size distribution in the range of 0.1-0.4 mm)flow with Ar and Ar-H2 plasma generated by radio frequency inductively coupled pla...Numerical simulation of turbulent mixing process of polydisperse quartz particle(particle size distribution in the range of 0.1-0.4 mm)flow with Ar and Ar-H2 plasma generated by radio frequency inductively coupled plasma(RF-ICP)torch has been made.An approximate two-stage approach has been proposed to calculate the spatial-temporal distributions of temperature and resulting thermal stress in quartz particles during dynamic heating in polydisperse plasma flow.The influence of working gas compositions,particle size distributions,injection angle and flow rate of carrier gas on the thermal destruction conditions of quartz particles has been determined under different particle feed rates.It is found that all the solid quartz particles(0.1-0.4 mm)could be thermal destructed without overheating in RF-ICP torch system,when the hydrogen volume fraction in working gases is more than 1.5%-2%and particle feed rate is in a certain range.The values of the maximum and minimum feed rates have been determined under different hydrogen volume fractions.An optimal particle injection angle and flow rate of carrier gas is found around 50°-60°and 160-220 slpm,under which the value of maximum equivalent thermal stress in quartz particles is highest.展开更多
Since programing complex and dynamic heat source model for welding simulation is a complex job,the parametric methods are studied in this paper.Firstly,an overall flow to achieve automatically modeling welding was int...Since programing complex and dynamic heat source model for welding simulation is a complex job,the parametric methods are studied in this paper.Firstly,an overall flow to achieve automatically modeling welding was introduced.Secondly,an expert module rule for selecting welding heat source model was founded,which is based on simulation knowledge and experiences.Thirdly,a modularity routine method was investigated using writing with C++programing,which automatically creates subroutines of 3D dynamic heat source model for user.To realize the dynamic weld path,the local weld path coordinate system was moved in the global coordinate system and it is used to model the direction of weld gun,welding path and welding pose.The weld path data file was prepared by the automatic tool for the welding heat source subroutines.All above functions were integrated in the user interface and the connection with architecture was introduced.At last,a laser beam welding heat source modeling was automatically modeled and the weld pool geometry was compared with the reported literature.It demonstrated that the automated tool is valid for welding simulation.Since modeling became convenient for welding simulation using the tool proposed,it could be easy and useful for welding engineers to acquire the needed information.展开更多
A numerical investigation is conducted to explore the evolution of a plasma discharge and its interaction with the fluid flow based on a self-consistent fluid model which couples the discharge dynamics with the fluid ...A numerical investigation is conducted to explore the evolution of a plasma discharge and its interaction with the fluid flow based on a self-consistent fluid model which couples the discharge dynamics with the fluid dynamics.The effects of the applied voltage on the distribution of velocity and temperature in initially static air are parainetrically studied.Furthermore,the spatial structure of plasma discharge and the resulting force contours in streamwise and normal directions are discussed in detail.The result shows that the plasma actuator produces a net force that should always be directed away from the exposed electrode,which results in an ionic wind pushing particles into a jet downstream of the actuator.When the energy added by the plasma is taken into account,the ambient air temperature is increased slightly around the electrode,but the velocity is almost not affected.Therefore it is unlikely that the induced flow is buoyancy driven.For the operating voltages considered in this paper,the maximum induced velocity is found to follow a power law,i.e.,it is proportional to the applied voltage to the 3.5 power.This promises an efficient application in the flow control with plasma actuators.展开更多
Using molecular dynamics (MD) simulation, we study the thermal shock behavior of tungsten (W), which has been used for the plasma facing material (PFM) of tokamaks. The thermo-elastic stress wave, corresponding ...Using molecular dynamics (MD) simulation, we study the thermal shock behavior of tungsten (W), which has been used for the plasma facing material (PFM) of tokamaks. The thermo-elastic stress wave, corresponding to the collective displacement of atoms, is analyzed with the Lagrangian atomic stress method, of which the reliability is also analyzed. The stress wave velocity corresponds to the speed of sound in the material, which is not dependent on the thermal shock energy. The peak pressure of a normal stress wave increases with the increase of thermal shock energy. We analyze the temperature evolution of the thermal shock region according to the Fourier transformation. It can be seen that the “obvious” velocity of heat propagation is less than the velocity of the stress wave; further, that the thermo-elastic stress wave may contribute little to the transport of kinetic energy. The heat propagation can be described properly by the heat conduction equation. These results may be useful for understanding the process of the thermal shock of tungsten.展开更多
A complete thermodynamic model is described for temperature and heat flow distribution simulation for ventilation networks in underground mines.The method is called the Computational Energy Dynamics(CED)model of the h...A complete thermodynamic model is described for temperature and heat flow distribution simulation for ventilation networks in underground mines.The method is called the Computational Energy Dynamics(CED)model of the heat,mass,and energy transport.The Thermal and Humidity(TH)transport elements of the full model are described for advection,convection,and accumulation,encompassing heat capacity,radiation,latent heat for evaporation,and condensation in the airways,as well as variable heat conduction and accumulation in the rock strata.The thermal flywheel effect for time-dependent temperature field applications is included in the model solution.A CED model validation exercise is described,directly evaluating the iterated,minimized energy balance errors for the mechanical and thermal energy components for each network branch after a converged solution is determined.A simulation example relevant to mine safety and health is shown with the CED-TH model,demonstrating its capabilities in efficiency and accuracy in comparison with measurement results.展开更多
Computer chip is always accompanied by the increase of heat dissipation and miniaturization. The miniature heat pipes are widely used in notebook computer to resolve the heat dissipation problems. Maximum heat removed...Computer chip is always accompanied by the increase of heat dissipation and miniaturization. The miniature heat pipes are widely used in notebook computer to resolve the heat dissipation problems. Maximum heat removed model of miniature heat pipes building by grey model is presented. In order to know the foundation for modeling, the smooth grade of error examination is inquired and the accuracy of grey relational grade is verified. The model can be used to select a suitable heat pipes to solve electric heat problems in the future. Final results show that the grey model only needs four experiment data and its error value is less than 10%, further, it is better than computational fluid dynamics (CFD) model.展开更多
Based on quasipotential analysis, a plasma sheath is studied through the derivation of the Sagdeev potential equation in dusty plasma coexisting with adiabatically heated electrons and ions. Salient features as to the...Based on quasipotential analysis, a plasma sheath is studied through the derivation of the Sagdeev potential equation in dusty plasma coexisting with adiabatically heated electrons and ions. Salient features as to the existence of sheaths are shown by solving the Sagdeev potential equation through the Runge–Kutta method, with appropriate consideration of adiabatically heated electrons and ions in the dynamical system. It has been shown that adiabatic heating of plasma sets a limit to the critical dust speed depending on the densities and Mach number, and it is believed that its role is very important to the sheath. One present problem is the contraction of the sheath region whereby dust grains levitated into the sheath lead to a crystallization similar to the formation of nebulons and are compressed to a larger chunk of the dust cloud by shrinking of the sheath. Our overall observations advance knowledge of sheath formation and are expected to be of interest in astroplasmas.展开更多
The secondary solar heat gain,defined as the heat flows from glazing to indoor environment through longwave radiation and convection,grows with the increasing of glazing absorption.With the rapid development and appli...The secondary solar heat gain,defined as the heat flows from glazing to indoor environment through longwave radiation and convection,grows with the increasing of glazing absorption.With the rapid development and application of spectrally selective glazing,the secondary solar heat gain becomes the main way of glazing heat transfer and biggest proportion,and indicates it should not be simplified calculated conventionally.Therefore,a dynamic secondary solar heat gain model is developed with electrochromic glazing system in this study,taking into account with three key aspects,namely,optical model,heat transfer model,and outdoor radiation spectrum.Compared with the traditional K-Sc model,this new model is verified by on-site experimental measurements with dynamic outdoor spectrum and temperature.The verification results show that the root mean square errors of the interior and exterior glass surface temperature are 3.25°C and 3.33°C,respectively,and the relative error is less than 10.37%.The root mean square error of the secondary heat gain is 13.15 W/m2,and the dynamic maximum relative error is only 13.2%.The simulated and measured results have a good agreement.In addition,the new model is further extended to reveal the variation characteristics of secondary solar heat gain under different application conditions(including orientations,locations,EC film thicknesses and weather conditions).In summary,based on the outdoor spectrum and window spectral characteristics,the new model can accurately calculate the increasing secondary solar heat gain in real time,caused by spectrally selective windows,and will provide a computational basis for the evaluation and development of spectrally selective glazing materials.展开更多
Concerning the specific demand on solving the long-term conjugate heat transfer (CHT) problem, a new algorithm of the global tightly-coupled transient heat transfer based on the quasi-steady flow field is further pu...Concerning the specific demand on solving the long-term conjugate heat transfer (CHT) problem, a new algorithm of the global tightly-coupled transient heat transfer based on the quasi-steady flow field is further put forward. Compared to the traditional loosely-coupled algorithm, the computational efficiency is further improved with the greatly reduced update frequency of the flow field, and moreover the update step of the flow field can be reasonably determined by using the engineering empirical formula of the Nusselt number based on the changes of the inlet and outlet boundary conditions. Taking a duct heated by inner forced air flow heating process as an example, the comparing results to the tightly-coupled transient calculation by Fluent software shows that the new algorithm can significantly improve the computational efficiency with a reasonable accuracy on the transient temperature distribution, such as the computing time is reduced to 22,8% and 40% while the duct wall temperature deviation are 7% and 5% respectively using two flow update time step of 100 s and 50 s on the variable inlet-flow rate conditions.展开更多
This paper addresses the difficulties in pinpointing reasons for unexpectedly high energy consumption in construction, and in low-energy houses especially. Statistical methods are applied to improve the insight into t...This paper addresses the difficulties in pinpointing reasons for unexpectedly high energy consumption in construction, and in low-energy houses especially. Statistical methods are applied to improve the insight into the energy performance and heat dynamics of a building based on consumption records and weather data. Dynamical methods separate influences from outdoor temperature, solar radiation, and wind on the energy consumption in the building. The studied building is a low-energy house in Sisimiut, GreenLand. Weather conditions like large temperature differences between indoors and outdoors throughout tong winters, strong winds, and very different circumstances regarding solar radiation compared to areas where Low-energy houses are usually built, make the Location very interesting for modeling and testing purposes. In 2011 new measurement equipment was installed in the house, which will be used to develop more detailed models of the heat dynamics and energy performance in relation to different meteoroLogicaL variables, heating systems, and user behavior. This type of models is known as a graybox model and is been introduced in this paper.展开更多
In the study on Ca-Mg silicate crystalline glazes, we found some disequilibrated crystallization phenomena, such as non-crystallographic small angle forking and spheroidal growth, parasitism and wedging-form of crysta...In the study on Ca-Mg silicate crystalline glazes, we found some disequilibrated crystallization phenomena, such as non-crystallographic small angle forking and spheroidal growth, parasitism and wedging-form of crystals, dendritic growth, secondary nucleation, etc. Those phenomena possibly resulted from two factors: (1) partial temperature gradient, which is caused by heat asymmetry in the electrical resistance furnace, when crystals crystalize from silicate melt; (2) constitutional supercooling near the surface of crystals. The disparity of disequilibrated crystallization phenomena in different main crystalline phases causes various morphological features of the crystal aggregates. At the same time, disequilibrated crystallization causes great stress retained in the crystals, which results in cracks in glazes when the temperature drops. According to the results, the authors analyzed those phenomena and displayed correlative figures and data.展开更多
This paper proposes a distributed real-time state estimation(RTSE)method for the combined heat and power systems(CHPSs).First,a difference-based model for the heat system is established considering the dynamics of hea...This paper proposes a distributed real-time state estimation(RTSE)method for the combined heat and power systems(CHPSs).First,a difference-based model for the heat system is established considering the dynamics of heat systems.This heat system model is further used along with the power system steady-state model for holistic CHPS state estimation.A cubature Kalman filter(CKF)-based RTSE is developed to deal with the system nonlinearity while integrating both the historical and present measurement information.Finally,a multi-timescale asynchronous distributed computation scheme is designed to enhance the scalability of the proposed method for largescale systems.This distributed implementation requires only a small amount of information exchange and thus protects the privacy of different energy systems.Simulations carried out on two CHPSs show that the proposed method can significantly improve the estimation efficiency of CHPS without loss of accuracy compared with other existing models and methods.展开更多
Effective thermal control systems are essential for reliable operation of spacecraft.A dual-driven intelligent combination control strategy is proposed to improve the temperate control and heat flux tracking effects.B...Effective thermal control systems are essential for reliable operation of spacecraft.A dual-driven intelligent combination control strategy is proposed to improve the temperate control and heat flux tracking effects.Both temperature regulation and heat flux tracking errors are employed to generate the final control action;their contributions are adaptively adjusted by a fuzzy fusing policy of control actions.To evaluate the control effects,describe a four-nodal mathematical model for analyzing the dynamic characteristics of the controlled heat pipe space cooling system(HP-SCS) consisting of an aluminum-ammonia heat pipe and a variable-emittance micro-electromechanical-system(MEMS) radiator.This dynamical model calculates the mass flow-rate and condensing pressure of the heat pipe working fluid directly from the systemic nodal temperatures,therefore,it is more suitable for control engineering applications.The closed-loop transient performances of four different control schemes have been numerically investigated.The results conclude that the proposed intelligent combination control scheme not only improves the thermal control effects but also benefits the safe operation of HP-SCS.展开更多
Effects of different parameters on the melting, vaporization and resolidification processes of thin gold film irradiated by femtosecond pulses and pulse train were systematically studied. The classical two-temperature...Effects of different parameters on the melting, vaporization and resolidification processes of thin gold film irradiated by femtosecond pulses and pulse train were systematically studied. The classical two-temperature model was adopted to depict the non-equilibrium heat transfer in electrons and lattice, the melting and resolidification processes, which was~ characterized by the solid-liquid interfacial velocity, as well as elevated melting temperature and depressed solidifcation tempera- ture, was obtained by considering the interfacial energy balance and nucleation dynamics. Vaporization process which leads to ablation was described by tracking the location of liquid-vapor interface with an iterative procedure based on energy balance and gas kinetics law. The parameters in discussion included film thickness, laser fluence, pulse duration, pulse number, repetition rate, pulse train number, etc. Their effects on the maximum lattice temperature, melting depth and ablation depth were discussed based on the simulation results.展开更多
Open source feld operation and manipulation(OpenFOAM)is one of the most prevalent open source computational fluid dynamics(CFD)software.It is very convenient for researchers to develop their own codes based on the...Open source feld operation and manipulation(OpenFOAM)is one of the most prevalent open source computational fluid dynamics(CFD)software.It is very convenient for researchers to develop their own codes based on the class library toolbox within OpenFOAM.In recent years,several density-based solvers within OpenFOAM for supersonic/hypersonic compressible flow are coming up.Although the capabilities of these solvers to capture shock wave have already been verifed by some researchers,these solvers still need to be validated comprehensively as commercial CFD software.In boundary layer where diffusion is the dominant transportation manner,the convective discrete schemes'capability to capture aerothermal variables,such as temperature and heat flux,is different from each other due to their own numerical dissipative characteristics and from viewpoint of this capability,these compressible solvers within OpenFOAM can be validated further.In this paper,frstly,the organizational architecture of density-based solvers within OpenFOAM is analyzed.Then,from the viewpoint of the capability to capture aerothermal variables,the numerical results of several typical geometrical felds predicted by these solvers are compared with both the outcome obtained from the commercial software Fastran and the experimental data.During the computing process,the Roe,AUSM+(Advection Upstream Splitting Method),and HLLC(Harten-Lax-van Leer-Contact)convective discrete schemes of which the spatial accuracy is 1st and 2nd order are utilized,respectively.The compared results show that the aerothermal variables are in agreement with results generated by Fastran and the experimental data even if the1st order spatial precision is implemented.Overall,the accuracy of these density-based solvers can meet the requirement of engineering and scientifc problems to capture aerothermal variables in diffusion boundary layer.展开更多
基金supported by National Natural Science Foundation of China(Nos.52202460,52177128)National Key R&D Program of China(Nos.2020YFC2201100,2021YFC2202804)+2 种基金China Postdoctoral Science Foundation(Nos.2021M690392,2021TQ0036)Science Foundation for Youth Scholars of the Beijing Institute of TechnologyAdvanced Space Propulsion Laboratory of BICE and the Beijing Engineering Research Centre of Efficient and Green Aerospace Propulsion Technology(No.LabASP-2021-04)。
文摘In the present work,the turbulent mixing process of a polydisperse quartz particle flow with a plasma stream generated by a radio-frequency(RF)inductively coupled plasma torch was numerically studied.The thermobaric stress in the quartz particles under dynamic heating in a heterogeneous plasma flow was determined by a two-stage approximation approach.The effect of the presence of vacuoles in natural quartz on the particle thermobaric destruction conditions was studied.It was found that the equivalent thermal and baric stresses in quartz particles may significantly increase in the presence of vacuoles within a small gas volume fraction.The influence of the regime and energetic working conditions of an RF inductively coupled plasma torch system on the particle thermobaric destruction conditions was examined,and a recommendation was given to promote the degree of thermobaric destruction of quartz particles,which is of substantial importance for improving the overall enrichment efficiency of quartz concentrates.
文摘Numerical simulation of turbulent mixing process of polydisperse quartz particle(particle size distribution in the range of 0.1-0.4 mm)flow with Ar and Ar-H2 plasma generated by radio frequency inductively coupled plasma(RF-ICP)torch has been made.An approximate two-stage approach has been proposed to calculate the spatial-temporal distributions of temperature and resulting thermal stress in quartz particles during dynamic heating in polydisperse plasma flow.The influence of working gas compositions,particle size distributions,injection angle and flow rate of carrier gas on the thermal destruction conditions of quartz particles has been determined under different particle feed rates.It is found that all the solid quartz particles(0.1-0.4 mm)could be thermal destructed without overheating in RF-ICP torch system,when the hydrogen volume fraction in working gases is more than 1.5%-2%and particle feed rate is in a certain range.The values of the maximum and minimum feed rates have been determined under different hydrogen volume fractions.An optimal particle injection angle and flow rate of carrier gas is found around 50°-60°and 160-220 slpm,under which the value of maximum equivalent thermal stress in quartz particles is highest.
基金supported by Young Innovative Talents Training Plan of Heilongjiang(UNPYSCT-2018133).
文摘Since programing complex and dynamic heat source model for welding simulation is a complex job,the parametric methods are studied in this paper.Firstly,an overall flow to achieve automatically modeling welding was introduced.Secondly,an expert module rule for selecting welding heat source model was founded,which is based on simulation knowledge and experiences.Thirdly,a modularity routine method was investigated using writing with C++programing,which automatically creates subroutines of 3D dynamic heat source model for user.To realize the dynamic weld path,the local weld path coordinate system was moved in the global coordinate system and it is used to model the direction of weld gun,welding path and welding pose.The weld path data file was prepared by the automatic tool for the welding heat source subroutines.All above functions were integrated in the user interface and the connection with architecture was introduced.At last,a laser beam welding heat source modeling was automatically modeled and the weld pool geometry was compared with the reported literature.It demonstrated that the automated tool is valid for welding simulation.Since modeling became convenient for welding simulation using the tool proposed,it could be easy and useful for welding engineers to acquire the needed information.
基金supported by the Foundation for Innovative Research Groups of National Natural Science Foundation of China(No.51121004)National Natural Science Foundation of China(No.50976026)
文摘A numerical investigation is conducted to explore the evolution of a plasma discharge and its interaction with the fluid flow based on a self-consistent fluid model which couples the discharge dynamics with the fluid dynamics.The effects of the applied voltage on the distribution of velocity and temperature in initially static air are parainetrically studied.Furthermore,the spatial structure of plasma discharge and the resulting force contours in streamwise and normal directions are discussed in detail.The result shows that the plasma actuator produces a net force that should always be directed away from the exposed electrode,which results in an ionic wind pushing particles into a jet downstream of the actuator.When the energy added by the plasma is taken into account,the ambient air temperature is increased slightly around the electrode,but the velocity is almost not affected.Therefore it is unlikely that the induced flow is buoyancy driven.For the operating voltages considered in this paper,the maximum induced velocity is found to follow a power law,i.e.,it is proportional to the applied voltage to the 3.5 power.This promises an efficient application in the flow control with plasma actuators.
基金Project supported by the National Magnetic Confinement Fusion Science Program of China(Grant No.2013GB109004)the National Natural Science Foundation of China(Grant Nos.51071095 and 50971077)
文摘Using molecular dynamics (MD) simulation, we study the thermal shock behavior of tungsten (W), which has been used for the plasma facing material (PFM) of tokamaks. The thermo-elastic stress wave, corresponding to the collective displacement of atoms, is analyzed with the Lagrangian atomic stress method, of which the reliability is also analyzed. The stress wave velocity corresponds to the speed of sound in the material, which is not dependent on the thermal shock energy. The peak pressure of a normal stress wave increases with the increase of thermal shock energy. We analyze the temperature evolution of the thermal shock region according to the Fourier transformation. It can be seen that the “obvious” velocity of heat propagation is less than the velocity of the stress wave; further, that the thermo-elastic stress wave may contribute little to the transport of kinetic energy. The heat propagation can be described properly by the heat conduction equation. These results may be useful for understanding the process of the thermal shock of tungsten.
基金the Alpha Foundation for the Improvement of Mine Safety and Health,Inc.National Institute of Occupational Safety and Health(NIOSH)
文摘A complete thermodynamic model is described for temperature and heat flow distribution simulation for ventilation networks in underground mines.The method is called the Computational Energy Dynamics(CED)model of the heat,mass,and energy transport.The Thermal and Humidity(TH)transport elements of the full model are described for advection,convection,and accumulation,encompassing heat capacity,radiation,latent heat for evaporation,and condensation in the airways,as well as variable heat conduction and accumulation in the rock strata.The thermal flywheel effect for time-dependent temperature field applications is included in the model solution.A CED model validation exercise is described,directly evaluating the iterated,minimized energy balance errors for the mechanical and thermal energy components for each network branch after a converged solution is determined.A simulation example relevant to mine safety and health is shown with the CED-TH model,demonstrating its capabilities in efficiency and accuracy in comparison with measurement results.
文摘Computer chip is always accompanied by the increase of heat dissipation and miniaturization. The miniature heat pipes are widely used in notebook computer to resolve the heat dissipation problems. Maximum heat removed model of miniature heat pipes building by grey model is presented. In order to know the foundation for modeling, the smooth grade of error examination is inquired and the accuracy of grey relational grade is verified. The model can be used to select a suitable heat pipes to solve electric heat problems in the future. Final results show that the grey model only needs four experiment data and its error value is less than 10%, further, it is better than computational fluid dynamics (CFD) model.
文摘Based on quasipotential analysis, a plasma sheath is studied through the derivation of the Sagdeev potential equation in dusty plasma coexisting with adiabatically heated electrons and ions. Salient features as to the existence of sheaths are shown by solving the Sagdeev potential equation through the Runge–Kutta method, with appropriate consideration of adiabatically heated electrons and ions in the dynamical system. It has been shown that adiabatic heating of plasma sets a limit to the critical dust speed depending on the densities and Mach number, and it is believed that its role is very important to the sheath. One present problem is the contraction of the sheath region whereby dust grains levitated into the sheath lead to a crystallization similar to the formation of nebulons and are compressed to a larger chunk of the dust cloud by shrinking of the sheath. Our overall observations advance knowledge of sheath formation and are expected to be of interest in astroplasmas.
基金the National Natural Science Foundation of China(51808011)the Natural Science Foundation of Chongqing(2022NSCQ-MSX5521).
文摘The secondary solar heat gain,defined as the heat flows from glazing to indoor environment through longwave radiation and convection,grows with the increasing of glazing absorption.With the rapid development and application of spectrally selective glazing,the secondary solar heat gain becomes the main way of glazing heat transfer and biggest proportion,and indicates it should not be simplified calculated conventionally.Therefore,a dynamic secondary solar heat gain model is developed with electrochromic glazing system in this study,taking into account with three key aspects,namely,optical model,heat transfer model,and outdoor radiation spectrum.Compared with the traditional K-Sc model,this new model is verified by on-site experimental measurements with dynamic outdoor spectrum and temperature.The verification results show that the root mean square errors of the interior and exterior glass surface temperature are 3.25°C and 3.33°C,respectively,and the relative error is less than 10.37%.The root mean square error of the secondary heat gain is 13.15 W/m2,and the dynamic maximum relative error is only 13.2%.The simulated and measured results have a good agreement.In addition,the new model is further extended to reveal the variation characteristics of secondary solar heat gain under different application conditions(including orientations,locations,EC film thicknesses and weather conditions).In summary,based on the outdoor spectrum and window spectral characteristics,the new model can accurately calculate the increasing secondary solar heat gain in real time,caused by spectrally selective windows,and will provide a computational basis for the evaluation and development of spectrally selective glazing materials.
文摘Concerning the specific demand on solving the long-term conjugate heat transfer (CHT) problem, a new algorithm of the global tightly-coupled transient heat transfer based on the quasi-steady flow field is further put forward. Compared to the traditional loosely-coupled algorithm, the computational efficiency is further improved with the greatly reduced update frequency of the flow field, and moreover the update step of the flow field can be reasonably determined by using the engineering empirical formula of the Nusselt number based on the changes of the inlet and outlet boundary conditions. Taking a duct heated by inner forced air flow heating process as an example, the comparing results to the tightly-coupled transient calculation by Fluent software shows that the new algorithm can significantly improve the computational efficiency with a reasonable accuracy on the transient temperature distribution, such as the computing time is reduced to 22,8% and 40% while the duct wall temperature deviation are 7% and 5% respectively using two flow update time step of 100 s and 50 s on the variable inlet-flow rate conditions.
文摘This paper addresses the difficulties in pinpointing reasons for unexpectedly high energy consumption in construction, and in low-energy houses especially. Statistical methods are applied to improve the insight into the energy performance and heat dynamics of a building based on consumption records and weather data. Dynamical methods separate influences from outdoor temperature, solar radiation, and wind on the energy consumption in the building. The studied building is a low-energy house in Sisimiut, GreenLand. Weather conditions like large temperature differences between indoors and outdoors throughout tong winters, strong winds, and very different circumstances regarding solar radiation compared to areas where Low-energy houses are usually built, make the Location very interesting for modeling and testing purposes. In 2011 new measurement equipment was installed in the house, which will be used to develop more detailed models of the heat dynamics and energy performance in relation to different meteoroLogicaL variables, heating systems, and user behavior. This type of models is known as a graybox model and is been introduced in this paper.
基金Supported by the Natural Science Foundation of Fujian Province(No.D0 2 10 0 12 )
文摘In the study on Ca-Mg silicate crystalline glazes, we found some disequilibrated crystallization phenomena, such as non-crystallographic small angle forking and spheroidal growth, parasitism and wedging-form of crystals, dendritic growth, secondary nucleation, etc. Those phenomena possibly resulted from two factors: (1) partial temperature gradient, which is caused by heat asymmetry in the electrical resistance furnace, when crystals crystalize from silicate melt; (2) constitutional supercooling near the surface of crystals. The disparity of disequilibrated crystallization phenomena in different main crystalline phases causes various morphological features of the crystal aggregates. At the same time, disequilibrated crystallization causes great stress retained in the crystals, which results in cracks in glazes when the temperature drops. According to the results, the authors analyzed those phenomena and displayed correlative figures and data.
基金supported by the Science and Technology Project of State Grid Corporation of China(No.52060019001H)。
文摘This paper proposes a distributed real-time state estimation(RTSE)method for the combined heat and power systems(CHPSs).First,a difference-based model for the heat system is established considering the dynamics of heat systems.This heat system model is further used along with the power system steady-state model for holistic CHPS state estimation.A cubature Kalman filter(CKF)-based RTSE is developed to deal with the system nonlinearity while integrating both the historical and present measurement information.Finally,a multi-timescale asynchronous distributed computation scheme is designed to enhance the scalability of the proposed method for largescale systems.This distributed implementation requires only a small amount of information exchange and thus protects the privacy of different energy systems.Simulations carried out on two CHPSs show that the proposed method can significantly improve the estimation efficiency of CHPS without loss of accuracy compared with other existing models and methods.
基金National Natural Science Foundation of China(50506003)
文摘Effective thermal control systems are essential for reliable operation of spacecraft.A dual-driven intelligent combination control strategy is proposed to improve the temperate control and heat flux tracking effects.Both temperature regulation and heat flux tracking errors are employed to generate the final control action;their contributions are adaptively adjusted by a fuzzy fusing policy of control actions.To evaluate the control effects,describe a four-nodal mathematical model for analyzing the dynamic characteristics of the controlled heat pipe space cooling system(HP-SCS) consisting of an aluminum-ammonia heat pipe and a variable-emittance micro-electromechanical-system(MEMS) radiator.This dynamical model calculates the mass flow-rate and condensing pressure of the heat pipe working fluid directly from the systemic nodal temperatures,therefore,it is more suitable for control engineering applications.The closed-loop transient performances of four different control schemes have been numerically investigated.The results conclude that the proposed intelligent combination control scheme not only improves the thermal control effects but also benefits the safe operation of HP-SCS.
文摘Effects of different parameters on the melting, vaporization and resolidification processes of thin gold film irradiated by femtosecond pulses and pulse train were systematically studied. The classical two-temperature model was adopted to depict the non-equilibrium heat transfer in electrons and lattice, the melting and resolidification processes, which was~ characterized by the solid-liquid interfacial velocity, as well as elevated melting temperature and depressed solidifcation tempera- ture, was obtained by considering the interfacial energy balance and nucleation dynamics. Vaporization process which leads to ablation was described by tracking the location of liquid-vapor interface with an iterative procedure based on energy balance and gas kinetics law. The parameters in discussion included film thickness, laser fluence, pulse duration, pulse number, repetition rate, pulse train number, etc. Their effects on the maximum lattice temperature, melting depth and ablation depth were discussed based on the simulation results.
基金supported by the National Natural Science Foundation of China(Grant Nos.51176038,51121004)
文摘Open source feld operation and manipulation(OpenFOAM)is one of the most prevalent open source computational fluid dynamics(CFD)software.It is very convenient for researchers to develop their own codes based on the class library toolbox within OpenFOAM.In recent years,several density-based solvers within OpenFOAM for supersonic/hypersonic compressible flow are coming up.Although the capabilities of these solvers to capture shock wave have already been verifed by some researchers,these solvers still need to be validated comprehensively as commercial CFD software.In boundary layer where diffusion is the dominant transportation manner,the convective discrete schemes'capability to capture aerothermal variables,such as temperature and heat flux,is different from each other due to their own numerical dissipative characteristics and from viewpoint of this capability,these compressible solvers within OpenFOAM can be validated further.In this paper,frstly,the organizational architecture of density-based solvers within OpenFOAM is analyzed.Then,from the viewpoint of the capability to capture aerothermal variables,the numerical results of several typical geometrical felds predicted by these solvers are compared with both the outcome obtained from the commercial software Fastran and the experimental data.During the computing process,the Roe,AUSM+(Advection Upstream Splitting Method),and HLLC(Harten-Lax-van Leer-Contact)convective discrete schemes of which the spatial accuracy is 1st and 2nd order are utilized,respectively.The compared results show that the aerothermal variables are in agreement with results generated by Fastran and the experimental data even if the1st order spatial precision is implemented.Overall,the accuracy of these density-based solvers can meet the requirement of engineering and scientifc problems to capture aerothermal variables in diffusion boundary layer.