For expedited transportation,vehicular tunnels are often designed as two adjacent tunnels,which frequently experience dynamic stress waves from various orientations during blasting excavation.To analyze the impact of ...For expedited transportation,vehicular tunnels are often designed as two adjacent tunnels,which frequently experience dynamic stress waves from various orientations during blasting excavation.To analyze the impact of dynamic loading orientation on the stability of the twin-tunnel,a split Hopkinson pressure bar(SHPB)apparatus was used to conduct a dynamic test on the twin-tunnel specimens.The two tunnels were rotated around the specimen’s center to consider the effect of dynamic loading orientation.LS-DYNA software was used for numerical simulation to reveal the failure properties and stress wave propagation law of the twin-tunnel specimens.The findings indicate that,for a twin-tunnel exposed to a dynamic load from different orientations,the crack initiation position appears most often at the tunnel corner,tunnel spandrel,and tunnel floor.As the impact direction is created by a certain angle(30°,45°,60°,120°,135°,and 150°),the fractures are produced in the middle of the line between the left tunnel corner and the right tunnel spandrel.As the impact loading angle(a)is 90°,the tunnel sustains minimal damage,and only tensile fractures form in the surrounding rocks.The orientation of the impact load could change the stress distribution in the twin-tunnel,and major fractures are more likely to form in areas where the tensile stress is concentrated.展开更多
The study of high-energy and low-vulnerability propellants is important for the power performance and safety of solid propellant rocket motors.The modified split Hopkinson pressure bar(SHPB)tests are performed on two ...The study of high-energy and low-vulnerability propellants is important for the power performance and safety of solid propellant rocket motors.The modified split Hopkinson pressure bar(SHPB)tests are performed on two kinds of propellant with different crosslinking density to study the dynamic mechanical responses and damage-ignition mechanism.SHPB apparatus is equipped with a highperformance infrared camera and high-speed camera to capture the deformation,damage-ignition feature and temperature evolution images in the impact process.The results suggested that the mechanical responses and damage-ignition mechanism of the propellants were affected by the strain rates and crosslinking density.The damage-ignition degree is more intense and the reaction occurs earlier with the increase of strain rates.For propellant 1 with higher crosslinking density,the critical ignition strain rate is 4500 s^(-1).Two kinds of propellants show different ignition mechanism,i.e.crack generation,propagation and final fracture for propellant 1 while viscous shear flow for propellant 2.Meanwhile,the SEM images also reveal the difference of damage-ignition mechanism of the two kinds of propellants.Finally,the ignition mechanism under different strain rates and critical ignition strain rate of propellants are further explained by the theoretical calculation of temperature variations.展开更多
It is not uncommon that backfill material used in underground mining being exposed to repetitive dynamic stresses induced by blasting operations or rockburst events. Understanding the strength and fracture evolution o...It is not uncommon that backfill material used in underground mining being exposed to repetitive dynamic stresses induced by blasting operations or rockburst events. Understanding the strength and fracture evolution of backfilled stopes is critical to maintain the long-term stope stability and ensure safe mining activities. This paper aims to study the damage evolution of the backfill material and its host rock behaviour under three-dimensional(3D) dynamic loading. Using a true-triaxial testing machine, multiple samples of backfill material enclosed by country rock were fabricated and tested under various dynamic loadings with different true-triaxial confining stress conditions. In addition, the nuclear magnetic resonance(NMR) measurement was conducted on the samples before and after exerting static and dynamic loading to obtain their porosity distribution changes. The experiment results suggested that with the increase of the dynamic loading, the porosity of the backfill sample goes through a two-stage process,which shows a slightly linear decrease and then followed by an exponential increase. The research findings can help understand the damage mechanism and fracture development of backfilled stopes and its host rock in deep underground mines, which are constantly subject to the combination of 3D static confining stress and dynamic loading.展开更多
Centrifuge experiments are carried out to investigate the responses of suction bucket foundations under horizontal dynamic loading. The effects of loading amplitude, the size of the bucket and the structural weight on...Centrifuge experiments are carried out to investigate the responses of suction bucket foundations under horizontal dynamic loading. The effects of loading amplitude, the size of the bucket and the structural weight on the dynamic responses are investigated. It is shown that, when the loading amplitude is over a critical value, the sand at the upper part around the bucket softens or even liquefies. The liquefaction index (excess pore pressure divided by initial effective stress. In this paper, the developmental degree of excess pore pressure is described by liquefaction index) decreases from the upper part to the lower part of the sand foundation in the vertical direction and decreases from near to far away from the bucket's side wall in the horizontal direction, large settlements of the bucket and the sand around the bucket are induced by the horizontal dynamic loading. The dynamic responses of the bucket of a smaller height (when the diameter is the same) are heavier. A cyclic crack some distance near the bucket occurs in the sand.展开更多
Centrifugal experiments were carried out to investigate the responses of suction bucket foundations under horizontal and vertical dynamic loading. It is shown that when the loading amplitude is over a critical value, ...Centrifugal experiments were carried out to investigate the responses of suction bucket foundations under horizontal and vertical dynamic loading. It is shown that when the loading amplitude is over a critical value, the sand at the upper part around the bucket is softened or even liquefied. The excess pore pressure decreases from the upper part to the lower part of the sand layer in the vertical direction and decreases radially from the bucket's side wall in the horizontal direction. Large settlements of the bucket and the sand layer around the bucket are induced by dynamic loading. The dynamic responses of the bucket with smaller height (the same diameter) are heavier.展开更多
Steel fiber reinforced concrete(SFRC)has drawn extensive attention in recent years for its superior mechanical response to dynamic and impact loadings.Based on the existing test results,the highstrength steel fibers e...Steel fiber reinforced concrete(SFRC)has drawn extensive attention in recent years for its superior mechanical response to dynamic and impact loadings.Based on the existing test results,the highstrength steel fibers embedded in a concrete matrix usually play a strong bridging effect to enhance the bonding force between fiber and the matrix,and directly contribute to the improvement of the post-cracking behavior and residual strength of SFRC.To gain a better understanding of the action behavior of steel fibers in matrix and further capture the failure mechanism of SFRC under dynamic loads,the mesoscopic modeling approach that assumes SFRC to be composed of different mesoscale phases(i.e.,steel fibers,coarse aggregates,mortar matrix,and interfacial transition zone(ITZ))has been widely employed to simulate the dynamic responses of SFRC material and structural members.This paper presents a comprehensive review of the state-of-the-art mesoscopic models and simulations for SFRC under dynamic loading.Generation approaches for the SFRC mesoscale model in the simulation works,including steel fiber,coarse aggregate,and the ITZ between them,are reviewed and compared systematically.The material models for different phases and the interaction relationship between fiber and concrete matrix are summarized comprehensively.Additionally,some example applications for SFRC under dynamic loads(i.e.,compression,tension,and contact blast)simulated using the general mesoscale models are given.Finally,some critical analysis on the current shortcomings of the mesoscale modeling of SFRC is highlighted,which is of great significance for the future investigation and development of SFRC.展开更多
The changes in mechanical properties and fracture toughness by dynamic loading were investigated with experiments. The parameter R, which can reflect the effect of the loading rate and the temperature rising during th...The changes in mechanical properties and fracture toughness by dynamic loading were investigated with experiments. The parameter R, which can reflect the effect of the loading rate and the temperature rising during the high loading rate, could be employed to describe the constituent relation for the typical structure steel and its weld metal. The dynamic loading effect on the stress/strain fields and the temperature variation in the vicinity of the crack tip was analyzed by the finite element method, the dynamic fracture behavior was evaluated based on the local approach. It has been found that the Weibull stress is an effective fracture parameter, independent of the temperature and the loading rate.展开更多
Although computer capabilities have been improved significantly, a large-scale virtual reality (VR) system demands much more in terms of memory and computation than the current computer systems can offer. This paper...Although computer capabilities have been improved significantly, a large-scale virtual reality (VR) system demands much more in terms of memory and computation than the current computer systems can offer. This paper discusses two important issues related to VR performance and applications in building navigation. These are dynamic loading of models based on cell segmentation for the optimal VR operation, and the route optimization based on path planning for easy navigation. The VR model of engineering and information technology complex (EITC) building at the University of Manitoba is built as an example to show the feasibility of the proposed methods. The reality, enhanced by three-dimensional (3D) real-time interactivity and visualization, leads navigators into a state of the virtual building immersion.展开更多
The dynamic swain and strength of frozen silt under long-term dynamic loading are studied based on creep tests. Three groups of tests are performed (Groups I, II, and III). The initial deviator stresses of Groups I an...The dynamic swain and strength of frozen silt under long-term dynamic loading are studied based on creep tests. Three groups of tests are performed (Groups I, II, and III). The initial deviator stresses of Groups I and II are same and the dynamic stress ampli- tude of Group II is twice as that of Group I. The minimum value of dynamic stress in Group IlI is near zero and its dynamic stress amplitude is larger than those of Groups I and II. In tests of all three groups there are similar change trends of accttmulative sWain, but with different values. The accumulative swain curves consist of three stages, namely, the initial stage, the steady stage, and the gradual flow stage. In the tests of Groups I and II, during the initial stage with vibration times less than 50 loops the strain ampli- tude decreased with the increase of vibration times and then basically remained constant, fluctuating in a very small range. For the tests of Group III, during the initial and steady stages the sWain amplitude decreased with the increase of vibration times, and then increased rapidly in the gradual flow stage. The dynamic strength of frozen silt decreases and trends to terminal dynamic strength as the vibration times of loading increase.展开更多
To investigate the effect of dynamic loading on fracture behavior of weldedjoints of structural steel Q235B and 16Mn in common use and compare the earthquake resistances ofthe two kinds of materials, dynamic tension a...To investigate the effect of dynamic loading on fracture behavior of weldedjoints of structural steel Q235B and 16Mn in common use and compare the earthquake resistances ofthe two kinds of materials, dynamic tension and fracture toughness tests are carried out at roomtemperature. On the basis of the tests, the stress-strain fields near the crack tip of the compactspecimens are analyzed by three-dimensional finite element model. The test results and finiteelement analysis results show that, the fracture toughness of welds and base metal of 16Mn steelincreases with the increment of loading rate. Compared with 16Mn steel, Q235B steel is moresensitive to dynamic loading. The fracture toughness of welds of Q235B is comparatively low understatic loading and dynamic loading at room temperature. Compared with the static loading, thefracture toughness of Q235B parent metal under dynamic loading decreases by about four times.Therefore, it can be concluded that compared with 16Mn steel, the earthquake resistances of weld andparent metal of Q235B are rather poor.展开更多
This paper is the second in a two-part series that discusses the principal axes of M-DOF structures subjected to static and dynamic loads.The primary purpose of this series is to understand the magnitude of the dynami...This paper is the second in a two-part series that discusses the principal axes of M-DOF structures subjected to static and dynamic loads.The primary purpose of this series is to understand the magnitude of the dynamie response of structures to enable better design of structures and response modification devices/systems.Under idealized design condi- tions,the structural responses are obtained by using single directinn input ground motions in the direction of the intended response modification devices/systems,and by assuming that the responses of the structure is deconpleable in three mutual- ly perpendicular directions.This standard practice has been applied to both new and retrofitted structures using various seis- mic protective systems.Very limited information is available on the effects of neglecting the impact of directional couplings (cross effects of which torsion is a component)of the dynamic response of structures.In order to quantify such effects,it is necessary to examine the principal axes of structures under both static and dynamic loading.In this twn-part series,the first paper is concerned with static loading,which provides definitions and fundamental formulations,with the conclusion that cross effects of a statically loaded M-DOF structure resulting from the lack of principal axes are of insignificant magnitude. However,under dynamic or earthquake loading,a relatively small amount of energy transferred across perpendicular direc- tions is accumulated,which may result in significant enlargement of the structural response.This paper deals with a formu- lation to define the principal axes of M-DOF structures under dynamic loading and develops quantitative measures to identify cross effects resuhing from the non-existence of principal axes.展开更多
A series of tests were conducted to analyze temperature field distribution and thawing settlement of a thawing soil under static and dynamic loading at various cooling and thawing temperatures. The results demonstrate...A series of tests were conducted to analyze temperature field distribution and thawing settlement of a thawing soil under static and dynamic loading at various cooling and thawing temperatures. The results demonstrate: (1) the temperature field distribution of the thawing soil was not significantly influenced by the loading form under the tested loading conditions; similar results were obtained for samples at different dynamic loading frequencies and different dynamic loading ampli- tudes, which verified the independence of loading form and temperature field; (2) changed temperature field distributions were found in thawing soil with different cooling and thawing temperatures, and the cooling and thawing temperature of the samples were the main factors affecting their temperature distributions; (3) under the tested conditions, thawing set- tlements were little influenced by the thawing temperature and the dynamic loading frequency; and (4) a linear relation- ship existed between the thawing settlement and the cooling temperature, and a logarithmic function could be used to describe the relationship between the thawing settlement and the loading amplitude.展开更多
Ply-by-ply failure analysis of symmetric and anti-symmetric laminates under uniform sinusoidal transverse dynamic loading is performed for a specified duration.The study investigates the first ply failure load,followe...Ply-by-ply failure analysis of symmetric and anti-symmetric laminates under uniform sinusoidal transverse dynamic loading is performed for a specified duration.The study investigates the first ply failure load,followed by the detection of successive ply failures and their failure modes using various failure theories.Some of the well-established failure theories,mostly used by the researchers,are considered for the failure prediction in laminates.The finite element computational model based on higher order shear deformation displacement field is used for the failure analysis and the complete methodology is computer coded using FORTRAN.The ply-discount stiffness reduction scheme is employed to modify the material properties of the failed lamina.The failure theories used in the analysis are compared according to their ability to predict failure load,failed ply,failure mode and progression of failure.The failure analysis is performed for both the cross-ply and angle-ply laminates with all edges simply supported and clamped.The significance of fibre orientation and stacking sequence in terms of the strength of a laminate and failure progression is also highlighted.展开更多
To reveal the dynamic mechanical characteristics of deep rocks,a series of impact tests under triaxial static stress states corresponding to depths of 300-2400 m were conducted.The results showed that both the strain ...To reveal the dynamic mechanical characteristics of deep rocks,a series of impact tests under triaxial static stress states corresponding to depths of 300-2400 m were conducted.The results showed that both the strain rates and the stress environments in depth significantly affect the mechanical characteristics of rocks.The sensitivity of strain rate to the dynamic strength and deformation modulus shows a negative correlation with depth,indicating that producing penetrative cracks in deep environments is more difficult when damage occurs.The dynamic strength shows a tendency to decrease and then increase slightly,but decreases sharply finally.Transmissivity demonstrates a similar trend as that of strength,whereas reflectivity indicates the opposite trend.Furthermore,two critical depths with high dynamically induced hazard possibilities based on the China Jinping Underground Laboratory(CJPL)were proposed for deep engineering.The first critical depth is 600-900 m,beyond which the sensitivity of rock dynamic characteristics to the strain rate and restraint of circumferential stress decrease,causing instability of surrounding rocks under axial stress condition.The second one lies at 1500-1800 m,where the wave impedance and dynamic strength of deep surrounding rocks drop sharply,and the dissipation energy presents a negative value.It suggests that the dynamic instability of deep surrounding rocks can be divided into dynamic load dominant and dynamic load induced types,depending on the second critical depth.展开更多
The stability control of fissured rock is difficult,especially under static and dynamic loads in deep coal mines.In this paper,the dynamic mechanical properties,strain rate evolution and energy dissipation of fissured...The stability control of fissured rock is difficult,especially under static and dynamic loads in deep coal mines.In this paper,the dynamic mechanical properties,strain rate evolution and energy dissipation of fissured and anchored rocks were respectively obtained by SHPB tests.It was found that bolt can provide supporting efficiency-improving effect for fissured rock against dynamic disturbance,and this effect increased quadratically with decrease in anchoring angles.Then,the energy dissipation mechanism of anchored rock was obtained by slipping model.Furthermore,bolt energy-absorbing mechanism by instantaneous tensile-shear deformation was expressed based on material mechanics,which was the larger the anchoring angle,the smaller the energy absorption,and the less the contribution to supporting efficiency improvement.On this basis,the functional relationship between energy dissipation of anchored rock and energy absorption of bolt was established.Taking the coal-gangue separation system of Longgu coal mine as an example,the optimal anchoring angle can be determined as 57.5°–67.5°.Field monitoring showed fissured rock with the optimal anchoring angle,can not only effectively control the deformation,but also fully exert the energy-absorbing and efficiency-improving effect of bolt itself.This study provides guidance to the stability control and supporting design for deep engineering under the same or similar conditions.展开更多
This study explores the effects of dynamic and static loading on rock bolt performance a key factor in maintaining the structural safety of coal mine roadways susceptible to coal bursts.Employing a housemade load fram...This study explores the effects of dynamic and static loading on rock bolt performance a key factor in maintaining the structural safety of coal mine roadways susceptible to coal bursts.Employing a housemade load frame to simulate various failure scenarios,pretension-impact-pull tests on rock bolts were conducted to scrutinize their dynamic responses under varied static load conditions and their failure traits under combined loads.The experimental results denote that with increased impact energy,maximum and average impact loads on rock bolts escalate significantly under pretension,initiating plastic deformation beyond a certain threshold.Despite minor reductions in the yield load due to impactinduced damage,pretension aids in constraining post-impact deformation rate and fluctuation degree of rock bolts.Moreover,impact-induced plastic deformation causes internal microstructure dislocation,fortifying the stiffness of the rock bolt support system.The magnitude of this fortification is directly related to the plastic deformation induced by the impact.These findings provide crucial guidance for designing rock bolt support in coal mine roadway excavation,emphasizing the necessity to consider both static and dynamic loads for improved safety and efficiency.展开更多
Cavity growth in ductile metal materials under dynamic loading is investigated via the material point method. Two typical cavity effects in the region subjected to rarefaction wave are identified: (i) part of mater...Cavity growth in ductile metal materials under dynamic loading is investigated via the material point method. Two typical cavity effects in the region subjected to rarefaction wave are identified: (i) part of material particles flow away from the cavity in comparison to the initial loading velocity, (ii) local regions show weaker negative or even positive pressures. Neighboring cavities interact via coalescence of isobaric contours. The growth of cavity under tension shows staged behaviors. After the initial slow stage, the volume and the dimensions in both the tensile and transverse directions show linear growth rate with time until the global tensile wave arrives at the upper free surface. It is interesting that the growth rate in the transverse direction is faster than that in the tensile direction. The volume growth rate linearly increases with the initial tensile velocity. After the global tensile wave passed the cavity, both the maximum particle velocity in the tensile direction and the maximum particle velocity in the opposite direction increase logarithmically with the initial tensile speed. The shock wave reflected back from the cavity and compression wave from the free surface induce the initial behavior of interracial instabilities such as the Richtmyer-Meshkov instability, which is mainly responsible for the irregularity in the morphology of deformed cavity. The local temperatures and distribution of hot spots are determined by the plastic work. Compared with the dynamical process, the heat conduction is much slower.展开更多
To prepare ultra-high-yield strength twinning-induced plasticity(TWIP)steel and reveal its work hardening mechanism at different strain rates from the microcosmic range,the microstructure evolution mechanism of Fe–2...To prepare ultra-high-yield strength twinning-induced plasticity(TWIP)steel and reveal its work hardening mechanism at different strain rates from the microcosmic range,the microstructure evolution mechanism of Fe–20Mn–0.6C TWIP steel was investigated at strain rates of 10^(-4)–10^(3)s^(-1)using a high-speed tensile testing machine and a transmission electron microscope.The results show that the strain rate and deformation had a significant effect on the twin morphology of TWIP steels.At a strain rate of 10^(2)s^(-1),secondary deformation twins were developed,which intersected with the initial deformation twins and increased the resistance of dislocation movement,as well as the plasticity.TWIP steel at a strain rate of 10^(2)s^(-1)had a higher twin formation speed than that at 10^(0)s^(-1).At the same amount of deformation,the twin boundary fraction was higher and increased linearly at a strain rate of 10^(2)s^(-1),while the rule of twin growth at 10^(0)s^(-1)was conformed to S-curve change of DoseResp model.展开更多
The quality of fruits can be reduced due to some damages and impacts which occur during harvesting.One of the most important mechanical damages that can reduce the quality of ripe fruit quality is abrasion damage.This...The quality of fruits can be reduced due to some damages and impacts which occur during harvesting.One of the most important mechanical damages that can reduce the quality of ripe fruit quality is abrasion damage.This study focused on the effect of dynamic loading based on customary harvesting method on mulberry fruit properties.To this end,different maturity stage and storage regimes were considered.Color quality parameters,firmness,total soluble solid(TSS),total anthocyanins content(TAC)and abrasion area were the measured factors.The results revealed that none of the surveyed factors were stable during the experiment.The lightness(L^*),redness(a^*),yellowness(b^*),C^* value,firmness,TSS and TAC of immature and mature mulberry decreased during storage.The value of a^*,b^* and C^* increased as dropping height increased.However,L*value,firmness,TSS and TAC of mulberry fruit decreased at both maturity stages(immature and mature mulberry).Moreover,abrasion area increased at immature and mature mulberries by increasing the dropping height and storage time.展开更多
Coal and gas outbursts are dynamic disasters in which a large mass of gas and coal suddenly emerges in a mining space within a split second.The interaction between the gas pressure and stress environment is one of the...Coal and gas outbursts are dynamic disasters in which a large mass of gas and coal suddenly emerges in a mining space within a split second.The interaction between the gas pressure and stress environment is one of the key factors that induce coal and gas outbursts.In this study,first,the coupling relationship between the gas pressure in the coal body ahead of the working face and the dynamic load was investigated using experimental observations,numerical simulations,and mine-site investigations.It was observed that the impact rate of the dynamic load on the gas-bearing coal can significantly change the gas pressure.The faster the impact rate,the speedier the increase in gas pressure.Moreover,the gas pressure rise was faster closer to the impact interface.Subsequently,based on engineering background,we proposed three models of stress and gas pressure distribution in the coal body ahead of the working face:static load,stress disturbance,and dynamic load conditions.Finally,the gas pressure distribution and outburst mechanism were investigated.The high concentration of gas pressure appearing at the coal body ahead of the working face was caused by the dynamic load.The gas pressure first increased gradually to a peak value and then decreased with increasing distance from the working face.The increase in gas pressure plays a major role in outburst initiation by resulting in the ability to more easily reach the critical points needed for outburst initiation.Moreover,the stronger the dynamic load,the greater the outburst initiation risk.The results of this study provide practical guidance for the early warning and prevention of coal and gas outbursts.展开更多
基金supported by the National Natural Science Foundation of China(Grant Nos.52204104 and U19A2098)the Science and Technology Department of Sichuan Province,China(Grant No.2023YFH0022).
文摘For expedited transportation,vehicular tunnels are often designed as two adjacent tunnels,which frequently experience dynamic stress waves from various orientations during blasting excavation.To analyze the impact of dynamic loading orientation on the stability of the twin-tunnel,a split Hopkinson pressure bar(SHPB)apparatus was used to conduct a dynamic test on the twin-tunnel specimens.The two tunnels were rotated around the specimen’s center to consider the effect of dynamic loading orientation.LS-DYNA software was used for numerical simulation to reveal the failure properties and stress wave propagation law of the twin-tunnel specimens.The findings indicate that,for a twin-tunnel exposed to a dynamic load from different orientations,the crack initiation position appears most often at the tunnel corner,tunnel spandrel,and tunnel floor.As the impact direction is created by a certain angle(30°,45°,60°,120°,135°,and 150°),the fractures are produced in the middle of the line between the left tunnel corner and the right tunnel spandrel.As the impact loading angle(a)is 90°,the tunnel sustains minimal damage,and only tensile fractures form in the surrounding rocks.The orientation of the impact load could change the stress distribution in the twin-tunnel,and major fractures are more likely to form in areas where the tensile stress is concentrated.
基金China National Nature Science Foundation(Grant No.11872119)Foundation Strengthening Project(Grant No.2020-JCJQ-ZD-220)for supporting this project。
文摘The study of high-energy and low-vulnerability propellants is important for the power performance and safety of solid propellant rocket motors.The modified split Hopkinson pressure bar(SHPB)tests are performed on two kinds of propellant with different crosslinking density to study the dynamic mechanical responses and damage-ignition mechanism.SHPB apparatus is equipped with a highperformance infrared camera and high-speed camera to capture the deformation,damage-ignition feature and temperature evolution images in the impact process.The results suggested that the mechanical responses and damage-ignition mechanism of the propellants were affected by the strain rates and crosslinking density.The damage-ignition degree is more intense and the reaction occurs earlier with the increase of strain rates.For propellant 1 with higher crosslinking density,the critical ignition strain rate is 4500 s^(-1).Two kinds of propellants show different ignition mechanism,i.e.crack generation,propagation and final fracture for propellant 1 while viscous shear flow for propellant 2.Meanwhile,the SEM images also reveal the difference of damage-ignition mechanism of the two kinds of propellants.Finally,the ignition mechanism under different strain rates and critical ignition strain rate of propellants are further explained by the theoretical calculation of temperature variations.
基金National Natural Science Foundation of China (Grant No.51804079)Fujian Natural Science Foundation (Grant No.2019J05039)
文摘It is not uncommon that backfill material used in underground mining being exposed to repetitive dynamic stresses induced by blasting operations or rockburst events. Understanding the strength and fracture evolution of backfilled stopes is critical to maintain the long-term stope stability and ensure safe mining activities. This paper aims to study the damage evolution of the backfill material and its host rock behaviour under three-dimensional(3D) dynamic loading. Using a true-triaxial testing machine, multiple samples of backfill material enclosed by country rock were fabricated and tested under various dynamic loadings with different true-triaxial confining stress conditions. In addition, the nuclear magnetic resonance(NMR) measurement was conducted on the samples before and after exerting static and dynamic loading to obtain their porosity distribution changes. The experiment results suggested that with the increase of the dynamic loading, the porosity of the backfill sample goes through a two-stage process,which shows a slightly linear decrease and then followed by an exponential increase. The research findings can help understand the damage mechanism and fracture development of backfilled stopes and its host rock in deep underground mines, which are constantly subject to the combination of 3D static confining stress and dynamic loading.
基金This study programis supported by the fund of the Chinese Ocean Oil Co.and the Chinese Academy of Sciences ,KJCX2-SW-L03-01 (40025103) andthe National Natural Science Foundation of China (Grant No.10202024)
文摘Centrifuge experiments are carried out to investigate the responses of suction bucket foundations under horizontal dynamic loading. The effects of loading amplitude, the size of the bucket and the structural weight on the dynamic responses are investigated. It is shown that, when the loading amplitude is over a critical value, the sand at the upper part around the bucket softens or even liquefies. The liquefaction index (excess pore pressure divided by initial effective stress. In this paper, the developmental degree of excess pore pressure is described by liquefaction index) decreases from the upper part to the lower part of the sand foundation in the vertical direction and decreases from near to far away from the bucket's side wall in the horizontal direction, large settlements of the bucket and the sand around the bucket are induced by the horizontal dynamic loading. The dynamic responses of the bucket of a smaller height (when the diameter is the same) are heavier. A cyclic crack some distance near the bucket occurs in the sand.
基金the fund of Chinese Ocean Oil Co.Chinese Academy of Sciences(KZCX2-YW-302-02).
文摘Centrifugal experiments were carried out to investigate the responses of suction bucket foundations under horizontal and vertical dynamic loading. It is shown that when the loading amplitude is over a critical value, the sand at the upper part around the bucket is softened or even liquefied. The excess pore pressure decreases from the upper part to the lower part of the sand layer in the vertical direction and decreases radially from the bucket's side wall in the horizontal direction. Large settlements of the bucket and the sand layer around the bucket are induced by dynamic loading. The dynamic responses of the bucket with smaller height (the same diameter) are heavier.
基金the financial support from the National Natural Science Foundation of China(52178190 and 52078250)the Science and Technology on Near-Surface Detection Laboratory(6142414200505)+1 种基金the Interdisciplinary Innovation Fundation for Graduates,Nanjing University of Aeronautics and Astronautics(KXKCXJJ202005)The support provided by the China Scholarship Council(202006830096)during a visit of Zhangyu Wu to University College London。
文摘Steel fiber reinforced concrete(SFRC)has drawn extensive attention in recent years for its superior mechanical response to dynamic and impact loadings.Based on the existing test results,the highstrength steel fibers embedded in a concrete matrix usually play a strong bridging effect to enhance the bonding force between fiber and the matrix,and directly contribute to the improvement of the post-cracking behavior and residual strength of SFRC.To gain a better understanding of the action behavior of steel fibers in matrix and further capture the failure mechanism of SFRC under dynamic loads,the mesoscopic modeling approach that assumes SFRC to be composed of different mesoscale phases(i.e.,steel fibers,coarse aggregates,mortar matrix,and interfacial transition zone(ITZ))has been widely employed to simulate the dynamic responses of SFRC material and structural members.This paper presents a comprehensive review of the state-of-the-art mesoscopic models and simulations for SFRC under dynamic loading.Generation approaches for the SFRC mesoscale model in the simulation works,including steel fiber,coarse aggregate,and the ITZ between them,are reviewed and compared systematically.The material models for different phases and the interaction relationship between fiber and concrete matrix are summarized comprehensively.Additionally,some example applications for SFRC under dynamic loads(i.e.,compression,tension,and contact blast)simulated using the general mesoscale models are given.Finally,some critical analysis on the current shortcomings of the mesoscale modeling of SFRC is highlighted,which is of great significance for the future investigation and development of SFRC.
基金supported by the National Natural Science Foundation of China,No.50275107 Fok Ying Tung Education Foundation No.81405.
文摘The changes in mechanical properties and fracture toughness by dynamic loading were investigated with experiments. The parameter R, which can reflect the effect of the loading rate and the temperature rising during the high loading rate, could be employed to describe the constituent relation for the typical structure steel and its weld metal. The dynamic loading effect on the stress/strain fields and the temperature variation in the vicinity of the crack tip was analyzed by the finite element method, the dynamic fracture behavior was evaluated based on the local approach. It has been found that the Weibull stress is an effective fracture parameter, independent of the temperature and the loading rate.
基金supported by Discovery Grants of National Science and Engineering Research Council of Canada (NSERC) and Faculty of Engineering at University of Manitoba
文摘Although computer capabilities have been improved significantly, a large-scale virtual reality (VR) system demands much more in terms of memory and computation than the current computer systems can offer. This paper discusses two important issues related to VR performance and applications in building navigation. These are dynamic loading of models based on cell segmentation for the optimal VR operation, and the route optimization based on path planning for easy navigation. The VR model of engineering and information technology complex (EITC) building at the University of Manitoba is built as an example to show the feasibility of the proposed methods. The reality, enhanced by three-dimensional (3D) real-time interactivity and visualization, leads navigators into a state of the virtual building immersion.
基金supported by the National Natural Science Foundation of China (Nos. 40971046, 41023003)the Project from the State Key Laboratory of Frozen Soil Engineering of China (No. 09SF102003)
文摘The dynamic swain and strength of frozen silt under long-term dynamic loading are studied based on creep tests. Three groups of tests are performed (Groups I, II, and III). The initial deviator stresses of Groups I and II are same and the dynamic stress ampli- tude of Group II is twice as that of Group I. The minimum value of dynamic stress in Group IlI is near zero and its dynamic stress amplitude is larger than those of Groups I and II. In tests of all three groups there are similar change trends of accttmulative sWain, but with different values. The accumulative swain curves consist of three stages, namely, the initial stage, the steady stage, and the gradual flow stage. In the tests of Groups I and II, during the initial stage with vibration times less than 50 loops the strain ampli- tude decreased with the increase of vibration times and then basically remained constant, fluctuating in a very small range. For the tests of Group III, during the initial and steady stages the sWain amplitude decreased with the increase of vibration times, and then increased rapidly in the gradual flow stage. The dynamic strength of frozen silt decreases and trends to terminal dynamic strength as the vibration times of loading increase.
基金This project is supported by National Natural Science Foundation of China (No.59975066).
文摘To investigate the effect of dynamic loading on fracture behavior of weldedjoints of structural steel Q235B and 16Mn in common use and compare the earthquake resistances ofthe two kinds of materials, dynamic tension and fracture toughness tests are carried out at roomtemperature. On the basis of the tests, the stress-strain fields near the crack tip of the compactspecimens are analyzed by three-dimensional finite element model. The test results and finiteelement analysis results show that, the fracture toughness of welds and base metal of 16Mn steelincreases with the increment of loading rate. Compared with 16Mn steel, Q235B steel is moresensitive to dynamic loading. The fracture toughness of welds of Q235B is comparatively low understatic loading and dynamic loading at room temperature. Compared with the static loading, thefracture toughness of Q235B parent metal under dynamic loading decreases by about four times.Therefore, it can be concluded that compared with 16Mn steel, the earthquake resistances of weld andparent metal of Q235B are rather poor.
基金a contract from the Federal Highway Adiministration(Contract No.ETFH61-98-C-00094)a Grant from the Earthquake Education Research Centers Program of the National Science Foundation to the Multidisciplinary Center for Earthquake Engineering Research(Grant No.EEC-9701471)
文摘This paper is the second in a two-part series that discusses the principal axes of M-DOF structures subjected to static and dynamic loads.The primary purpose of this series is to understand the magnitude of the dynamie response of structures to enable better design of structures and response modification devices/systems.Under idealized design condi- tions,the structural responses are obtained by using single directinn input ground motions in the direction of the intended response modification devices/systems,and by assuming that the responses of the structure is deconpleable in three mutual- ly perpendicular directions.This standard practice has been applied to both new and retrofitted structures using various seis- mic protective systems.Very limited information is available on the effects of neglecting the impact of directional couplings (cross effects of which torsion is a component)of the dynamic response of structures.In order to quantify such effects,it is necessary to examine the principal axes of structures under both static and dynamic loading.In this twn-part series,the first paper is concerned with static loading,which provides definitions and fundamental formulations,with the conclusion that cross effects of a statically loaded M-DOF structure resulting from the lack of principal axes are of insignificant magnitude. However,under dynamic or earthquake loading,a relatively small amount of energy transferred across perpendicular direc- tions is accumulated,which may result in significant enlargement of the structural response.This paper deals with a formu- lation to define the principal axes of M-DOF structures under dynamic loading and develops quantitative measures to identify cross effects resuhing from the non-existence of principal axes.
基金provided by National Natural Science Foundation of China (NSFC) under Grant Nos.41001036 and 41171064
文摘A series of tests were conducted to analyze temperature field distribution and thawing settlement of a thawing soil under static and dynamic loading at various cooling and thawing temperatures. The results demonstrate: (1) the temperature field distribution of the thawing soil was not significantly influenced by the loading form under the tested loading conditions; similar results were obtained for samples at different dynamic loading frequencies and different dynamic loading ampli- tudes, which verified the independence of loading form and temperature field; (2) changed temperature field distributions were found in thawing soil with different cooling and thawing temperatures, and the cooling and thawing temperature of the samples were the main factors affecting their temperature distributions; (3) under the tested conditions, thawing set- tlements were little influenced by the thawing temperature and the dynamic loading frequency; and (4) a linear relation- ship existed between the thawing settlement and the cooling temperature, and a logarithmic function could be used to describe the relationship between the thawing settlement and the loading amplitude.
文摘Ply-by-ply failure analysis of symmetric and anti-symmetric laminates under uniform sinusoidal transverse dynamic loading is performed for a specified duration.The study investigates the first ply failure load,followed by the detection of successive ply failures and their failure modes using various failure theories.Some of the well-established failure theories,mostly used by the researchers,are considered for the failure prediction in laminates.The finite element computational model based on higher order shear deformation displacement field is used for the failure analysis and the complete methodology is computer coded using FORTRAN.The ply-discount stiffness reduction scheme is employed to modify the material properties of the failed lamina.The failure theories used in the analysis are compared according to their ability to predict failure load,failed ply,failure mode and progression of failure.The failure analysis is performed for both the cross-ply and angle-ply laminates with all edges simply supported and clamped.The significance of fibre orientation and stacking sequence in terms of the strength of a laminate and failure progression is also highlighted.
基金supported by the National Natural Science Foundation of China(No.U1965203).
文摘To reveal the dynamic mechanical characteristics of deep rocks,a series of impact tests under triaxial static stress states corresponding to depths of 300-2400 m were conducted.The results showed that both the strain rates and the stress environments in depth significantly affect the mechanical characteristics of rocks.The sensitivity of strain rate to the dynamic strength and deformation modulus shows a negative correlation with depth,indicating that producing penetrative cracks in deep environments is more difficult when damage occurs.The dynamic strength shows a tendency to decrease and then increase slightly,but decreases sharply finally.Transmissivity demonstrates a similar trend as that of strength,whereas reflectivity indicates the opposite trend.Furthermore,two critical depths with high dynamically induced hazard possibilities based on the China Jinping Underground Laboratory(CJPL)were proposed for deep engineering.The first critical depth is 600-900 m,beyond which the sensitivity of rock dynamic characteristics to the strain rate and restraint of circumferential stress decrease,causing instability of surrounding rocks under axial stress condition.The second one lies at 1500-1800 m,where the wave impedance and dynamic strength of deep surrounding rocks drop sharply,and the dissipation energy presents a negative value.It suggests that the dynamic instability of deep surrounding rocks can be divided into dynamic load dominant and dynamic load induced types,depending on the second critical depth.
基金the financial support from the National Natural Science Foundation of China(Nos.52374094,52174122 and 52374218)Excellent Youth Fund of Shandong Natural Science Foundation(No.ZR2022YQ49)Taishan Scholar Project in Shandong Province(Nos.tspd20210313 and tsqn202211150)。
文摘The stability control of fissured rock is difficult,especially under static and dynamic loads in deep coal mines.In this paper,the dynamic mechanical properties,strain rate evolution and energy dissipation of fissured and anchored rocks were respectively obtained by SHPB tests.It was found that bolt can provide supporting efficiency-improving effect for fissured rock against dynamic disturbance,and this effect increased quadratically with decrease in anchoring angles.Then,the energy dissipation mechanism of anchored rock was obtained by slipping model.Furthermore,bolt energy-absorbing mechanism by instantaneous tensile-shear deformation was expressed based on material mechanics,which was the larger the anchoring angle,the smaller the energy absorption,and the less the contribution to supporting efficiency improvement.On this basis,the functional relationship between energy dissipation of anchored rock and energy absorption of bolt was established.Taking the coal-gangue separation system of Longgu coal mine as an example,the optimal anchoring angle can be determined as 57.5°–67.5°.Field monitoring showed fissured rock with the optimal anchoring angle,can not only effectively control the deformation,but also fully exert the energy-absorbing and efficiency-improving effect of bolt itself.This study provides guidance to the stability control and supporting design for deep engineering under the same or similar conditions.
基金supported by the National Natural Science Foundation of China(Nos.52074151,51927807,and 52274123)Tiandi Science and Technology Co.,Ltd.(No.2022-2-TDMS012)。
文摘This study explores the effects of dynamic and static loading on rock bolt performance a key factor in maintaining the structural safety of coal mine roadways susceptible to coal bursts.Employing a housemade load frame to simulate various failure scenarios,pretension-impact-pull tests on rock bolts were conducted to scrutinize their dynamic responses under varied static load conditions and their failure traits under combined loads.The experimental results denote that with increased impact energy,maximum and average impact loads on rock bolts escalate significantly under pretension,initiating plastic deformation beyond a certain threshold.Despite minor reductions in the yield load due to impactinduced damage,pretension aids in constraining post-impact deformation rate and fluctuation degree of rock bolts.Moreover,impact-induced plastic deformation causes internal microstructure dislocation,fortifying the stiffness of the rock bolt support system.The magnitude of this fortification is directly related to the plastic deformation induced by the impact.These findings provide crucial guidance for designing rock bolt support in coal mine roadway excavation,emphasizing the necessity to consider both static and dynamic loads for improved safety and efficiency.
文摘Cavity growth in ductile metal materials under dynamic loading is investigated via the material point method. Two typical cavity effects in the region subjected to rarefaction wave are identified: (i) part of material particles flow away from the cavity in comparison to the initial loading velocity, (ii) local regions show weaker negative or even positive pressures. Neighboring cavities interact via coalescence of isobaric contours. The growth of cavity under tension shows staged behaviors. After the initial slow stage, the volume and the dimensions in both the tensile and transverse directions show linear growth rate with time until the global tensile wave arrives at the upper free surface. It is interesting that the growth rate in the transverse direction is faster than that in the tensile direction. The volume growth rate linearly increases with the initial tensile velocity. After the global tensile wave passed the cavity, both the maximum particle velocity in the tensile direction and the maximum particle velocity in the opposite direction increase logarithmically with the initial tensile speed. The shock wave reflected back from the cavity and compression wave from the free surface induce the initial behavior of interracial instabilities such as the Richtmyer-Meshkov instability, which is mainly responsible for the irregularity in the morphology of deformed cavity. The local temperatures and distribution of hot spots are determined by the plastic work. Compared with the dynamical process, the heat conduction is much slower.
基金This work is funded by the National Natural Science Foundation of China(No.U 1860112)the Guidance Plan of Liaoning Natural Science Foundation(No.2019-ZD-0025)+1 种基金the Key Project of Liaoning Education Department(No.2019FWDF03)the Postdoctoral Research Support Project of Hebei(No.B2019003031).
文摘To prepare ultra-high-yield strength twinning-induced plasticity(TWIP)steel and reveal its work hardening mechanism at different strain rates from the microcosmic range,the microstructure evolution mechanism of Fe–20Mn–0.6C TWIP steel was investigated at strain rates of 10^(-4)–10^(3)s^(-1)using a high-speed tensile testing machine and a transmission electron microscope.The results show that the strain rate and deformation had a significant effect on the twin morphology of TWIP steels.At a strain rate of 10^(2)s^(-1),secondary deformation twins were developed,which intersected with the initial deformation twins and increased the resistance of dislocation movement,as well as the plasticity.TWIP steel at a strain rate of 10^(2)s^(-1)had a higher twin formation speed than that at 10^(0)s^(-1).At the same amount of deformation,the twin boundary fraction was higher and increased linearly at a strain rate of 10^(2)s^(-1),while the rule of twin growth at 10^(0)s^(-1)was conformed to S-curve change of DoseResp model.
文摘The quality of fruits can be reduced due to some damages and impacts which occur during harvesting.One of the most important mechanical damages that can reduce the quality of ripe fruit quality is abrasion damage.This study focused on the effect of dynamic loading based on customary harvesting method on mulberry fruit properties.To this end,different maturity stage and storage regimes were considered.Color quality parameters,firmness,total soluble solid(TSS),total anthocyanins content(TAC)and abrasion area were the measured factors.The results revealed that none of the surveyed factors were stable during the experiment.The lightness(L^*),redness(a^*),yellowness(b^*),C^* value,firmness,TSS and TAC of immature and mature mulberry decreased during storage.The value of a^*,b^* and C^* increased as dropping height increased.However,L*value,firmness,TSS and TAC of mulberry fruit decreased at both maturity stages(immature and mature mulberry).Moreover,abrasion area increased at immature and mature mulberries by increasing the dropping height and storage time.
基金the financial support from the China Postdoctoral Science Foundation(Nos.2022M713384,and 2022M721450)the National Natural Science Foundation of China(Nos.52174187,51704164,and 52130409)the Technology Innovation Fund of China Coal Research Institute(No.2020CX-I-07).
文摘Coal and gas outbursts are dynamic disasters in which a large mass of gas and coal suddenly emerges in a mining space within a split second.The interaction between the gas pressure and stress environment is one of the key factors that induce coal and gas outbursts.In this study,first,the coupling relationship between the gas pressure in the coal body ahead of the working face and the dynamic load was investigated using experimental observations,numerical simulations,and mine-site investigations.It was observed that the impact rate of the dynamic load on the gas-bearing coal can significantly change the gas pressure.The faster the impact rate,the speedier the increase in gas pressure.Moreover,the gas pressure rise was faster closer to the impact interface.Subsequently,based on engineering background,we proposed three models of stress and gas pressure distribution in the coal body ahead of the working face:static load,stress disturbance,and dynamic load conditions.Finally,the gas pressure distribution and outburst mechanism were investigated.The high concentration of gas pressure appearing at the coal body ahead of the working face was caused by the dynamic load.The gas pressure first increased gradually to a peak value and then decreased with increasing distance from the working face.The increase in gas pressure plays a major role in outburst initiation by resulting in the ability to more easily reach the critical points needed for outburst initiation.Moreover,the stronger the dynamic load,the greater the outburst initiation risk.The results of this study provide practical guidance for the early warning and prevention of coal and gas outbursts.