Dynamic modeling of total ionizing dose-induced threshold voltage shifts in MOS devices

The total ionizing dose(TID) effect is a key cause for the degradation/failure of semiconductor device performance under energetic-particle irradiation. We developed a dynamic model of mobile particles and defects by solving the rate equations and Poisson's equation simultaneously, to understand threshold voltage shifts induced by TID in silicon-based metal–oxide–semiconductor(MOS) devices. The calculated charged defect distribution and corresponding electric field under different TIDs are consistent with experiments. TID changes the electric field at the Si/SiO_(2) interface by inducing the accumulation of oxide charged defects nearby, thus shifting the threshold voltage accordingly. With increasing TID, the oxide charged defects increase to saturation, and the electric field increases following the universal 2/3 power law. Through analyzing the influence of TID on the interfacial electric field by different factors, we recommend that the radiation-hardened performance of devices can be improved by choosing a thin oxide layer with high permittivity and under high gate voltages.

Dynamic Modeling and Sensitivity Analysis for an MEA-Based CO_(2) Capture Absorber

The absorber is the key unit in the post-combustion monoethanolamine(MEA)-based carbon dioxide(CO_(2))capture process.A rate-based dynamic model for the absorber is developed and validated using steady-state experimental data reported in open literature.Sensitivity analysis is performed with respect to important model parameters associated with the reaction,mass transport and phy-sical property relationships.Then,a singular value decomposition(SVD)-based subspace parameter estimation method is proposed to improve the model accu-racy.Finally,dynamic simulations are carried out to investigate the effects of the feed rate of lean MEA solution and the flue inlet conditions.Simulation results indicate that the established dynamic model can reasonably reflect the physical behavior of the absorber.Some new insights are gained from the simulation results.

Review on Dynamic Modeling and Vibration Characteristics of Rotating Cracked Blades

As one of the most important parts in the engine,the structure and state of the rotating blade directly affect the normal performance of the aeroengine.In order to monitor engine crack failure and ensure flight safety,it is necessary to carry out research on the dynamic modeling of the cracked blade and breathing crack-induced vibration mechanisms.This paper summarizes the current research status on the dynamics of cracked blade,and the related topics mainly include four aspects:crack propagation path,mechanical model of open and breathing cracks,dynamic modeling methods of cracked blades such as lumped mass model,semi-analytical model and finite element model,and dynamic characteristics of cracked blades.The review will provide valuable references for future studies on dynamics and fault diagnosis of cracked blade in aeroengine.

Research on Mixed Logic Dynamic Modeling and Finite Control Set Model Predictive Control of Multi-Inverter Parallel System

Parallel connection of multiple inverters is an important means to solve the expansion,reserve and protection of distributed power generation,such as photovoltaics.In view of the shortcomings of traditional droop control methods such as weak anti-interference ability,low tracking accuracy of inverter output voltage and serious circulation phenomenon,a finite control set model predictive control(FCS-MPC)strategy of microgrid multiinverter parallel system based on Mixed Logical Dynamical(MLD)modeling is proposed.Firstly,the MLD modeling method is introduced logical variables,combining discrete events and continuous events to form an overall differential equation,which makes the modeling more accurate.Then a predictive controller is designed based on the model,and constraints are added to the objective function,which can not only solve the real-time changes of the control system by online optimization,but also effectively obtain a higher tracking accuracy of the inverter output voltage and lower total harmonic distortion rate(Total Harmonics Distortion,THD);and suppress the circulating current between the inverters,to obtain a good dynamic response.Finally,the simulation is carried out onMATLAB/Simulink to verify the correctness of the model and the rationality of the proposed strategy.This paper aims to provide guidance for the design and optimal control of multi-inverter parallel systems.

Dynamic Modeling and Analysis of Occult Transmission of Omicron SARS-CoV-2 Epidemic

At present, the Omicron variant is still the dominant strain in the global novel coronavirus pneumonia pandemic, and has the characteristics of concealed transmission, which brings heavy pressure to the health systems of different countries. Omicron infections were first found in Chinese Mainland in Tianjin in December 2021, and Omicron epidemic broke out in many parts of China in 2022. In order to enable the country and government to make scientific and accurate decisions in the face of the epidemic, it is particularly important to predict and analyze the relevant factors of Omicron’s covert transmission. In this paper, based on the official data of Jilin City and the improved SEIR dynamic model, through parameter estimation, the contact infection probability of symptomatic infected persons in Omicron infected patients is 0.4265, and the attenuation factor is 0.1440. Secondly, the influence of infectious duration in different incubation periods, asymptomatic infected persons and other factors on the epidemic situation in this area was compared. Finally, the scale of epidemic development was predicted and analyzed.

Dynamic Modeling and Motion Simulation for A Winged Hybrid-Driven Underwater Glider

PETREL, a winged hybrid-driven underwater glider is a novel and practical marine survey platform which combines the features of legacy underwater glider and conventional AUV （autonomous underwater vehicle）. It can be treated as a multi-rigid-body system with a floating base and a particular hydrodynamic profile. In this paper, theorems on linear and angular momentum are used to establish the dynamic equations of motion of each rigid body and the effect of translational and rotational motion of internal masses on the attitude control are taken into consideration. In addition, due to the unique external shape with fixed wings and deflectable rudders and the dual-drive operation in thrust and glide modes, the approaches of building dynamic model of conventional AUV and hydrodynamic model of submarine are introduced, and the tailored dynamic equations of the hybrid glider are formulated. Moreover, the behaviors of motion in glide and thrust operation are analyzed based on the simulation and the feasibility of the dynamic model is validated by data from lake field trials.

Dynamic Modeling and Three-Dimensional Motion Analysis of Underwater Gliders

For consideration of both the eccentric rotatable rigid body and the translational rigid body, the dynamic model of the underwater glider is derived. Dynamical behaviors are also studied based on the model and can be used as the guidance to underwater gliders design. Gibbs function of the underwater glider system is derived first, and then the nonlinear dynamic model is obtained by use of Appell equations. The relationships between dynamic behaviors and design parameters are studied by solving the dynamic model. The spiral motion, swerving motion in three dimensions and the saw-tooth motion of the underwater glider in vertical plane are studied. Lake trials are carried out to validate the dynamic model.

Dynamic Modeling of a Roller Chain Drive System Considering the Flexibility of Input Shaft

Roller chain drives are widely used in various high-speed, high-load and power transmission applications, but their complex dynamic behavior is not well researched. Most studies were only focused on the analysis of the vibration of chain tight span, and in these models, many factors are neglected. In this paper, a mathematical model is developed to calculate the dynamic response of a roller chain drive working at constant or variable speed condition. In the model, the complete chain transmission with two sprockets and the necessary tight and slack spans is used. The effect of the flexibility of input shaft on dynamic response of the chain system is taken into account, as well as the elastic deformation in the chain, the inertial forces, the gravity and the torque on driven shaft. The nonlinear equations of movement are derived from using Lagrange equations and solved numerically. Given the center distance and the two initial position angles of teeth on driving and driven sprockets corresponding to the first seating roller on each side of the tight span, dynamics of any roller chain drive with two sprockets and two spans can be analyzed by the procedure. Finally, a numerical example is given and the validity of the procedure developed is demonstrated by analyzing the dynamic behavior of a typical roller chain drive. The model can well simulate the transverse and longitudinal vibration of the chain spans and the torsional vibration of the sprockets. This study can provide an effective method for the analysis of the dynamic characteristics of all the chain drive systems.

Dynamic Modeling and Experiment of a New Type of Parallel Servo Press Considering Gravity Counterbalance

The large capacity servo press is traditionally realized by means of redundant actuation, however there exist the over-constraint problem and interference among actuators, which increases the control difficulty and the product cost. A new type of press mechanism with parallel topology is presented to develop the mechanical servo press with high stamping capacity. The dynamic model considering gravity counterbalance is proposed based on the virtual work principle, and then the effect of counterbalance cylinder on the dynamic performance of the servo press is studied. It is found that the motor torque required to operate the press is a lot less than the others when the ratio of the counterbalance force to the gravity of ram is in the vicinity of 1.0. The stamping force of the real press prototype can reach up to 25 MN on the position of 13 mm away from the bottom dead center. The typical deep-drawing process with 1 200 mm stroke at 8 strokes per minute is proposed by means of five order polynomial. On this process condition, the driving torques are calculated based on the above dynamic model and the torque measuring test is also carried out on the prototype. It is shown that the curve trend of calculation torque is consistent to the measured result and that the average error is less than 15%. The parallel mechanism is introduced into the development of large capacity servo press to avoid the over-constraint and interference of traditional redundant actuation, and its dynamic characteristics with gravity counterbalance are presented.

Dynamic Modeling and Analysis of 9-DOF Omnidirectional Legged Vehicle

The omnidirectional legged vehicle with steering-rails has a specific mechanism feature, and it can be controlled flexibly and accurately in omnidirectional motion. Currently there lacks further research in this area. In this paper, the mechanical characteristics of independent walking control and steering control and its kinematics principle are introduced, and a vehicle has a composite motion mode of parallel link mechanism and steering mechanism is presented. The motion direction control of the proposed vehicle is only dependant on its steering rails, so its motion is simple and effective to control. When the relative motion between the walking and steering is controlled cooperatively, the vehicle can walk perfectly. By controlling the steering rails, the vehicle can walk along arbitrary trajectory on the ground. To achieve a good result of motion control, an equivalent manipulator model needs to be built. In terms of the mechanism feature and the kinematic principle, the simplified manipulator model consists of a rail in stance phase, a rail in swing phase, and an equivalent leg. Considering the ground surface slope during walking, a parameter of inclination angle is added. Based on such a RPP manipulator model, the equations of motion are derived by means of Lagrangian dynamic approach. To verify the dynamic equations, the motion of the manipulator model is simulated based on linear and nonlinear motion planning. With the same model and motion parameters, the dynamic equations can be solved by Matlab and the calculation data can be gained. Compared with the simulation data, the result confirms the manipulator dynamic equations are correct. As a result of such special characteristics of the legged mechanism with steering rails, it has a potential broad application prospects. The derivation of dynamics equation could benefit the motion control of the mechanism.

Dynamic Modeling and Eigenvalue Evaluation of a 3-DOF PKM Module

Due to the structural complexity, the dynamic modeling and quick performance evaluation for the parallel kinematic machines （PKMs） are still to be remained as two challenges in the stage of conceptual design. By using the finite element method and substructure synthesis, this paper mainly deals with the dynamic modeling and eigenvalue evaluation of a novel 3-DOF spindle head named the A3 head. The topological architecture behind the proposed A3 head is a 3-RPS parallel mechanism, which possesses one translational and two rotational capabilities. The mechanical features of the A3 head are briefly addressed in the first place followed by inverse position analysis. In the dynamic modeling, the platform is treated as a rigid body, the RPS limbs as the continuous uniform beams and the joints as lumped virtual springs. With the combination of substructure synthesis and finite element method, an analytical approach is then proposed to formulate the governing equations of motion of system using the compatibility conditions at interface between the limbs and the platform. Consequently, by solving the eigenvalue problem of the governing equations of motion, the distribution of lower natural frequencies of the A3 head throughout the entire workspace can be predicted in a quick manner. Modal analysis for the A3 head reveals that the distributions of lower natural frequencies are strongly related to the mechanism configuration and are axially symmetric due to system kinematic and structural features. The sensitivity analysis of the system indicates that the dimensional parameters of the 3-RPS mechanism have a slight effect on system lower natural frequencies while the joint compliances affect the distributions of lower natural frequencies significantly. The proposed dynamic modeling method can also be applied to other PKMs and can effectively evaluate the PKM＇s dynamic performance throughout the entire workspace.

ON THE DYNAMIC MODELING AND CONTROL OF 2-DOF PLANAR PARALLEL MECHANISM WITH FLEXIBLE LINKS

The object of study is about dynamic modeling and control for a 2degree-of-freedom (DOF) planar parallel mechanism (PM) with flexible links. The kinematic anddynamic equations are established according to the characteristics of mixed rigid and flexiblestructure. By using the singular perturbation approach (SPA), the model of the mechanism can beseparated into slow and fast subsystems. Based on the feedback linearization theory and inputshaping technique, the large scale rigid motion controller and the flexible link vibrationcontroller can be designed separately to achieve fast and accurate positioning of the PM.

Dynamic modeling and control of extracellular ATP concentration on vascular endothelial cells via shear stress modulation

A new dynamic model for cell-deformation-induced adenosine triphosphate （ATP） release from vascular endothelial cells （VECs） is proposed in this paper to quantify the relationship between the ATP concentration at the surface of VECs and blood flow-induced shear stress. The simulation results demonstrate that ATP concentration at the surface of VECs predicted by the proposed new dynamic model is more consistent with the experimental observations than those by the existing static and dynamic models. Furthermore, it is the first time that a proportional-integral-derivative （PID） feedback controller is applied to modulate extracellular ATP concentration. Three types of desired ATP concentration profiles including constant, square wave and sinusoid are obtained by regulating the wall shear stress under this PID control. The systematic methodology utilized in this paper to model and control ATP release from VECs via adjusting external stimulus opens up a new scenario where quantitative investigations into the underlying mechanisms for many biochemical phenomena can be carded out for the sake of controlling specific cellular events.

Dynamic Modeling and Analysis of 4UPS-UPU Spatial Parallel Mechanism with Spherical Clearance Joint

Clearance between the moving joints is unavoidable in real working process. At present, many researches are mainly focused on dynamics of plane revolute joint in plane mechanism, but few on dynamics of spatial spherical joint clearance in spatial parallel mechanism. In this paper, a general method is proposed for establishing dynamic equations of spatial parallel mechanism with spatial spherical clearance by Lagrange multiplier method. The kinematic model and contact force model of the spherical joint clearance were established successively. Lagrange multiplier method was used to deduce the dynamics equation of 4 UPS-UPU mechanism with spherical clearance joint systematically. The influence of friction coefficient on dynamics response of 4 UPS-UPU mechanism with spherical clearance joint was analyzed. Non-linear characteristics of clearance joint and moving platform were analyzed by Poincare map, phase diagram, and bifurcation diagram. The results show that variation of friction coefficient and clearance value had little effect on stability of the mechanism, but the chaotic phenomenon was found at spherical clearance joint. The research has theoretical guiding significance for improving the dynamic performance and avoiding of chaos of parallel mechanisms including spherical joint clearance.

NONLINEAR DYNAMIC MODELING AND PERIODIC VIBRATION OF A CANTILEVER BEAM SUBJECTED TO AXIAL MOVEMENT OF BASEMENT

Dynamic modeling of a cantilever beam under an axial movement ofits basement is present- ed. The dynamic equation of motion for thecantilever beam is established by using Kane's equation first andthen simplified through the Rayleigh-Ritz method. Compared with oldermodeling method, which lineari- zes the generalized inertia forcesand the generalized active forces, the present modeling takes thecoupled cubic nonlinearities of geometrical and inertial types intoconsideration.

Dynamic Modeling of the Feed Drive System of a CNC Metal Cutting Machine

Studying the vibrational behavior of feed drive systems is important for enhancing the structural performance of computer numerical control(CNC)machines.The preload on the screw and nut position have a great influence on the vibration characteristics of the feed drive as two very important operational conditions.Rotational acceleration of the screw also affects the performance of the CNC feed drive when machining small parts.This paper investigates the influence of preload and nut position on the vibration characteristics of the feed drive system of a CNC metal cutting machine in order to be able to eliminate an observed resonance occurred at high rotational speeds of the screw,corresponding to high feed rates.Additionally,rational structural parameters of the feed drive system are selected in order to increase the rotational acceleration for improving the performance of the CNC machine.Experiments and analyses showed that by selecting specific parameters of feed drive system and simultaneously applying a certain value of preload,a 97%increase in rotational acceleration and 30%time reduction considering the vibration resistance at high rotational speeds can be achieved.

The Dynamic Modeling Algorithm of Information Organization and Allocation Problem on Internet Communications

With the frequent information accesses from users to the Internet, it is important to organize and allocate information resources properly on different web servers. This paper considers the following problem; Due to the capacity limitation of each single web server, it is impossible to put all information resources on one web server. Hence it is an important problem to put them on several different servers such as: (1) the amount of information resources assigned on any server is less than its capacity; (2) the access bottleneck can be avoided. In order to solve the problem in which the access frequency is variable, this paper proposes a dynamic optimal modeling. Based on the computational complexity results, the paper further focuses on the genetic algorithm for solving the dynamic problem. Finally we give the simulation results and conclusions.

DYNAMIC MODELING FOR AIRSHIP EQUIPPED WITH BALLONETS AND BALLAST

Total dynamics of an airship is modeled. The body of an airship is taken as a submerged rigid body with neutral buoyancy, i. e. , buoyancy with value equal to that of gravity, and the coupled dynamics between the body with ballonets and ballast is considered. The total dynamics of the airship is firstly derived by Newton-Euler laws and Kirchhoff＇ s equations. Furthermore, by using Hamiltonian and Lagrangian semidirect product reduction theories, the dynamics is formulated as a Lie-Poisson system, or also an Euler-Poincare system. These two formulations can be exploited for the control design using energy-based methods for Hamiltonian or Lagrangian system.

Roll System and Stock's Multi-parameter Coupling Dynamic Modeling Based on the Shape Control of Steel Strip

The existence of rolling deformation area in the rolling mill system is the main characteristic which dis- tinguishes the other machinery. In order to analyze the dynamic property of roll system＇s flexural deformation, it is necessary to consider the transverse periodic movement of stock in the rolling deformation area which is caused by the flexural deformation movement of roll system simul- taneously. Therefore, the displacement field of roll system and flow of metal in the deformation area is described by kinematic analysis in the dynamic system. Through intro- ducing the lateral displacement function of metal in the deformation area, the dynamic variation of per unit width rolling force can be determined at the same time. Then the coupling law caused by the co-effect of rigid movement and flexural deformation of the system structural elements is determined. Furthermore, a multi-parameter coupling dynamic model of the roll system and stock is established by the principle of virtual work. More explicitly, the cou- pled motion modal analysis was made for the roll system. Meanwhile, the analytical solutions for the flexural defor- mation movement＇s mode shape functions of rolls are discussed. In addition, the dynamic characteristic of the lateral flow of metal in the rolling deformation area has been analyzed at the same time. The establishment ofdynamic lateral displacement function of metal in the deformation area makes the foundation for analyzing the coupling law between roll system and rolling deformation area, and provides a theoretical basis for the realization of the dynamic shape control of steel strip.

Dynamic Modeling and Investigation of Maneuver Characteristics of A Deep-Sea Manned Submarine Vehicle

A deep-sea Manned Submarine Vehicle （MSV） is usually required to move at a low forward speed and a low rotational speed when it executes investigation tasks. In this condition, the motion is in large drift angles, and the maneuverability hydrodynamic forces cannot be expressed properly in the conventional mathematical model of submersible motion. In this paper, firstly, a general equation of MSV with six-freedom motion is presented, and the numerical simulation of descent/ascent motion and helix motion is conducted to reveal the general maneuver characteristics of MSV. Secondly, according to the data of captive model tests of large drift angles of MSV, the regression analysis of position hydrodynamic forces and rotation hydrodynamic forces is carried out, and the results of regression analysis of maneuverability hydrody- namic characteristics are analyzed to reveal the special maneuver characteristics. Thirdly, a special new mathematical model of MSV with the whole range of drift angles motion is presented, which can be used to predict hydrodynamic performance of motion in the 0° - 180° range of drift angles. The results are applied to the design of maneuverability hydrodynamic forces, development of control system and simulator of a practical MSV.