High-energy gas fracturing of shale is a novel,high efficacy and eco-friendly mining technique,which is a typical dynamic perturbing behavior.To effectively extract shale gas,it is important to understand the dynamic ...High-energy gas fracturing of shale is a novel,high efficacy and eco-friendly mining technique,which is a typical dynamic perturbing behavior.To effectively extract shale gas,it is important to understand the dynamic mechanical properties of shale.Dynamic experiments on shale subjected to true triaxial compression at different strain rates are first conducted in this research.The dynamic stress-strain curves,peak strain,peak stress and failure modes of shale are investigated.The results of the study indicate that the intermediate principal stress and the minor principal stress have the significant influence on the dynamic mechanical behaviors,although this effect decreases as the strain rate increases.The characteristics of compression-shear failure primarily occur in shale subjected to triaxial compression at high strain rates,which distinguishes it from the fragmentation characteristics observed in shale under dynamic uniaxial compression.Additionally,a numerical three-dimensional Split Hopkinson Pressure Bar(3D-SHPB),which is established by coupling PFC3D and FLAC3D methods,is validated to replicate the laboratory characteristics of shale.The dynamic mechanical characteristics of shale subjected to different confining stresses are systematically investigated by the coupling PFC3D and FLAC3D method.The numerical results are in good agreement with the experimental data.展开更多
With rapid economic and social development in China, high-rise buildings have continuously sprung up since 2006. However, several big fire accidents in high-rise buildings such as the Beijing Television Cultural Cente...With rapid economic and social development in China, high-rise buildings have continuously sprung up since 2006. However, several big fire accidents in high-rise buildings such as the Beijing Television Cultural Center fire in 2009 and the Shanghai Jing'an District fire in 2010 etc. have claimed people's lives and caused huge amounts of economic and property losses,展开更多
Although the research history of triboelectrification has been more than 2000 years, there are still many problems to be solved so far.The use of scanning probe microscopy provides an important way to quantitatively s...Although the research history of triboelectrification has been more than 2000 years, there are still many problems to be solved so far.The use of scanning probe microscopy provides an important way to quantitatively study the transfer, accumulation, and dissipation of triboelectric charges in the process of triboelectrification. Two-dimensional materials are considered to be key materials for new electronic devices in the post-Moore era due to their atomic-scale size advantages. If the electrostatic field generated by triboelectrification can be used to replace the traditional gate electrostatic field, it is expected to simplify the structure of two-dimensional electronic devices and reconfigure them at any time according to actual needs. Here, we investigate the triboelectrification process of various two-dimensional materials such as MoS_(2), WSe_(2),and ZnO. Different from traditional bulk materials, after two-dimensional materials are rubbed, the triboelectric charges generated may tunnel through the two-dimensional materials to the underlying substrate surface. Because the tunneling triboelectric charge is protected by the twodimensional material, its stable residence time on the substrate surface can reach more than 7 days, which is more than tens of minutes for the traditional triboelectric charge. In addition, the electrostatic field generated by the tunneling triboelectric charge can effectively regulate the carrier transport performance of two-dimensional materials, and the source–drain current of the field effect device regulated by the triboelectric floating gate is increased by nearly 60 times. The triboelectric charge tunneling phenomenon in two-dimensional materials is expected to be applied in the fields of new two-dimensional electronic devices and reconfigurable functional circuits.展开更多
The beer game model is a typical paradigm used to study complex dynamics behaviours in production–distribution systems. The model, however, does not accord with current practical supply chain system models in discret...The beer game model is a typical paradigm used to study complex dynamics behaviours in production–distribution systems. The model, however, does not accord with current practical supply chain system models in discrete?type manufacturing industry, which are generally composed of retailers, distributors, manufacturers with internal sup?ply chain, and suppliers. To describe how ordering policies influence the complex dynamics behaviour modes and operating cost in a general discrete?type manufacturing industry supply chain system, a high dimension piecewise?linear dynamics model is built for the supply chain system. Five kinds of ordering policy combination are considered. The distribution of both the largest Lyapunov exponent of e ective inventory and average operating cost per cycle is obtained by simulation in a policy space. The simulation shows that for the general discrete?type manufacturing industry supply chain system, the upper chaotic corners emerge besides the lower chaotic corners in the policy space expressing the distribution of system behaviour mode, and that the ordering policies at each supply chain node as well as their combination have very significant e ect on the topology of the distribution of both system behaviour mode and operating cost in the policy space. We find that chaos is not always corresponding to high cost, and the "chaos amplification" is not completely relevant to the "cost amplification".展开更多
Dynamic rheological characteristics of polypropylene (PP) filled with ultra-fine full-vulcanized powdered rubber (UFPR) composed of styrene-butadiene copolymer were studied through dynamic rheological measurements on ...Dynamic rheological characteristics of polypropylene (PP) filled with ultra-fine full-vulcanized powdered rubber (UFPR) composed of styrene-butadiene copolymer were studied through dynamic rheological measurements on an Advanced Rheometric Expansion System (ARES). A specific viscoelastic phenomenon, i.e. 'the second plateau', appeared at low frequencies, and exhibits a certain dependence on the amount of rubber particles and the dispersion state in the matrix. This phenomenon is attributed to the formation of aggregation structure of rubber particles. The analyses of Cole-Cole diagrams of the dynamic viscoelastic functions suggest that the heterogeneity of the composites is enhanced on increasing both particle content and temperature.展开更多
The radial symmetric motion problem was examined for a spherical shell composed of a class of imperfect incompressible hyper-elastic materials, in which the materials may be viewed as the homogeneous incompressible is...The radial symmetric motion problem was examined for a spherical shell composed of a class of imperfect incompressible hyper-elastic materials, in which the materials may be viewed as the homogeneous incompressible isotropic neo-Hookean material with radial perturbations. A second-order nonlinear ordinary differential equation that describes the radial motion of the inner surface of the shell was obtained. And the first integral of the equation was then carded out. Via analyzing the dynamical properties of the solution of the differential equation, the effects of the prescribed imperfection parameter of the material and the ratio of the inner and the outer radii of the underformed shell on the motion of the inner surface of the shell were discussed, and the corresponding numerical examples were carded out simultaneously. In particular, for some given parameters, it was proved that, there exists a positive critical value, and the motion of the inner surface with respect to time will present a nonlinear periodic oscillation as the difference between the inner and the outer presses does not exceed the critical value. However, as the difference exceeds the critical value, the motion of the inner surface with respect to time will increase infinitely. That is to say, the shell will be destroyed ultimately.展开更多
The single-layer latticed cylindrical shell is one of the most widely adopted space-fl'amed structures.In this paper,free vibration properties and dynamic response to horizontal and vertical seismic waves of singl...The single-layer latticed cylindrical shell is one of the most widely adopted space-fl'amed structures.In this paper,free vibration properties and dynamic response to horizontal and vertical seismic waves of single-layer latticed cylindrical shells are analyzed by the finite element method using ANSYS software.In the numerical study,where hundreds of cases were analyzed,the parameters considered included rise-span ratio,length-span ratio,surface load and member section size.Moreover,to better define the actual behavior of single-layer latticed shells,the study is focused on the dynamic stress response to both axial forces and bending moments.Based on the numerical results,the effects of the parameters considered on the stresses are discussed and a modified seismic force coefficient method is suggested.In addition,some advice based on these research results is presented to help in the future design of such structures.展开更多
Finger seal is a new technology developed for gas path sealing in gas turbine engine.It has been paid attention to its good sealing performance and lower manufacture cost.The vibration behavior of finger seal is not b...Finger seal is a new technology developed for gas path sealing in gas turbine engine.It has been paid attention to its good sealing performance and lower manufacture cost.The vibration behavior of finger seal is not be considered in performance analysis for the contact finger seal with compliant geometric configuration,then this will influence the reliability of the performance analysis and the parametric design of a finger seal.According to the dynamic character of finger seal,the harmonic vibration and free vibration models of a repetitive section of a two-layer finger seal that contains one high and one low finger seal are established separately.The dynamic behavior of finger seal in different working conditions is obtained based on the dynamic response analysis of finger's vibrations.The dynamic low hysteresis and low wear terms based on the equivalent dynamic model of finger seal are put forward,which can be used to predict the dynamic behavior of finger seal.As an example,the dynamic behaviors of an 8-layer finger seal and a 10-layer finger seal were predicted,and the validity of the prediction was demonstrated by the leakage test results of these two finger seals.The work presented here not only could make the dynamic analysis of finger seal with complicated structure simple and easy especially for multi-layer finger seal system,but also suggest a useful method for designing the finger seal with good dynamic behavior by means of different seal layers assembly.展开更多
The dynamic behavior of a bridge-erecting machine, carrying a moving mass suspended by a wire rope, is investigated. The bridge-erecting machine is modelled by a simply supported uniform beam, and a massless equivale...The dynamic behavior of a bridge-erecting machine, carrying a moving mass suspended by a wire rope, is investigated. The bridge-erecting machine is modelled by a simply supported uniform beam, and a massless equivalent "spring-damper" system with an effective spring constant and an effective damping coefficient is used to model the moving mass suspended by the wire rope. The suddenly applied load is represented by a unitary Dirac Delta function. With the expansion method, a simple closed-form solution for the equation of motion with the replaced spring-damper-mass system is formulated. The characters of the rope are included in the derivation of the differential equation of motion for the system. The numerical examples show that the effects of the damping coefficient and the spring constant of the rope on the deflection have significant variations with the loading frequency. The effects of the damping coefficient and the spring constant under different beam lengths are also examined. The obtained results validate the presented approach, and provide significant references in the design process of bridgeerecting machines.展开更多
The marine risers are often subjected to parametric excitations from the fluctuation top tension. The top tension on the riser may fluctuate with multiple frequencies caused by irregular waves. In this paper, the infl...The marine risers are often subjected to parametric excitations from the fluctuation top tension. The top tension on the riser may fluctuate with multiple frequencies caused by irregular waves. In this paper, the influence between different frequency components in the top tension on the riser system is theoretically simulated and analyzed. With the Euler-Bernoulli beam theory, a dynamic model for the vibrations of the riser is established. The top tension is set as fluctuating with time and it has two different frequencies. The influences from the fluctuation amplitudes, circular frequencies and phase angles of these frequency components on the riser system are analyzed in detail. When these two frequencies are fluctuating in the stable regions, the riser system may become unstable because ω1+ω2≈2Ωn. The fluctuation amplitudes of these frequencies have little effect on the components of the vibration frequencies of the riser. For different phase angles, the stability and dynamic behaviors of the riser would be different.展开更多
In this paper,(500 nm 1%+5μm 3%)bimodal scale Al2O3p/AZ31 composites was fabricated by solid state synthesis and the effect of bimodal scale Al2O3 particulates on its dynamic recrystallization behavior and mechanical...In this paper,(500 nm 1%+5μm 3%)bimodal scale Al2O3p/AZ31 composites was fabricated by solid state synthesis and the effect of bimodal scale Al2O3 particulates on its dynamic recrystallization behavior and mechanical properties was investigated.The optical microscopy,scanning electron microscopy,transmission electron microscopy and electron universal strength tester composites were used to characterize the composites.The results indicate that the grains size of the composites are significantly refined and the mechanical properties are obviously improved.Due to the presence of the bimodal scale Al2o3 particulates,the high-density dislocation zone is formed around nano-Al2o3p and the particle deformation zone is formed near micron-ABOap.These zones are ideal sites for the formation of recrystallization nucleus.Meanwhile,the addition of the bimodal scale Al2o3 particulates may delay or hinder the growth of matrix grain through the pining effect on the grain boundaries,resulting in significantly improving the yield strength and tensile strength of Al2O3p/AZ31 composites.展开更多
The study on rheological properties of a series of mica-filled polypropylene ( PP ) composites was carried out. The influence of surface-treatment of mica particles on dynamic rheological behavior of the composites w...The study on rheological properties of a series of mica-filled polypropylene ( PP ) composites was carried out. The influence of surface-treatment of mica particles on dynamic rheological behavior of the composites were dealt with. The viscosity ( h ) and dynamic modulus ( G ) of the composite melts were higher than those of PP matrix, especially those for systems treated with silane, which was attributed to the interfacial adhesion enhancement. However, surface-treatment of mica by titanate resulted in lower h and G, as compared with the treatment by silane. The reason for this is believed to be the formation of the mono-molecular layer on the mica surface.展开更多
The dynamic mechanical behavior of a novel polymeric composite damping material has been investigated in this article. The composite consists of chlorinated polyethylene (CPE), N,N-dicyclohexyl-2-benzothiazolylsufen...The dynamic mechanical behavior of a novel polymeric composite damping material has been investigated in this article. The composite consists of chlorinated polyethylene (CPE), N,N-dicyclohexyl-2-benzothiazolylsufenamide (DZ), 4,4'-thio-bis(3-methyl-6-tert-buthylphenol) (BPSR) and vapor-grown carbon fiber (VGCF). It is found that either the position or the intensity of damping peak can be controlled by changing the composition of CPE/DZ/BPSR composite. Within a certain composition region, damping peak maximum depends on CPE/DZ ratio, whereas damping peak position is controlled by BPSR content. Moreover, the improvement of storage modulus can be achieved by incorporation of VGCF. These results may imply that a damping material possessing both good damping properties and high strength can be designed and obtained.展开更多
In this article, we consider positive steady state solutions and dynamics for a spatially heterogeneous predator-prey system with modified Leslie-Gower and Holling-Type II schemes. The heterogeneity here is created by...In this article, we consider positive steady state solutions and dynamics for a spatially heterogeneous predator-prey system with modified Leslie-Gower and Holling-Type II schemes. The heterogeneity here is created by the degeneracy of the intra-specific pressures for the prey. By the bifurcation method, the degree theory, and a priori estimates, we discuss the existence and multiplicity of positive steady states. Moreover, by the comparison argument, we also discuss the dynamical behavior for the diffusive predator-prey system.展开更多
The dynamical behavior of two tethered rigid spheres in a supersonic flow is numerically investigated. The tethered lengths and radius ratios of the two spheres are different. The two spheres, which are centroid axial...The dynamical behavior of two tethered rigid spheres in a supersonic flow is numerically investigated. The tethered lengths and radius ratios of the two spheres are different. The two spheres, which are centroid axially aligned initially, are held stationary first, then released, and subsequently let fly freely in a supersonic flow. The mean qualities of the system and the qualities of the bigger sphere are considered and compared with the situations without the tether. In the separation process, six types of motion caused by the spheres, tether, and fluid interaction are found. The results show that the mean x-velocity of the system changes in a different manner for different radius ratios, and the x-velocity of the bigger sphere is uniformly reduced but through different mechanisms.展开更多
The dynamic mechanical behaviors of the Zr41Ti14Cu12.5Ni8Be22.5Fe2 bulk metallic glass (BMG) during continuous heating at a constant rate were investigated. The glass transition and crystallization of the Zr-based B...The dynamic mechanical behaviors of the Zr41Ti14Cu12.5Ni8Be22.5Fe2 bulk metallic glass (BMG) during continuous heating at a constant rate were investigated. The glass transition and crystallization of the Zr-based BMG were thus characterized by the measurements of storage modulus E′ and internal friction Q^-1. It was found that the variations of these dynamic mechanical quantities with temperature were interre-lated and were well in agreement with the DSC trace obtained at the same heating rate. The origin of the first peak in the internal friction curve was closely related to the dynamic glass transition and subsequent primary crystallization. Moreover, it can be well described by a physical model, which can characterize atomic mobility and mechanical response of disordered condense materials. In comparison with the DSC trace, the relative position of the first internal friction peak of the BMG was found to be dependent on its thermal stability against crys-tallization.展开更多
Polypropylene(PP)/ethylene-octene copolymer(POE) blends were prepared with a twin-screw extruder.Their dynamic mechanical behavior were systematically investigated.The results show that PP/POE blends are heterogen...Polypropylene(PP)/ethylene-octene copolymer(POE) blends were prepared with a twin-screw extruder.Their dynamic mechanical behavior were systematically investigated.The results show that PP/POE blends are heterogeneities with a partial compatible two-phase structure,the glass transition temperature of PP phases in the blends tends to shift towards high temperature with increasing the POE content,and the glass transition temperature of POE phases shifts towards the low temperature with increasing the PP content.The Kerner's dispersed phase model and co-continuous phase model can reasonably predict the visco-elasticity of PP/POE blends with different compositions.Additionally,the morphological structure of the blends can be estimated via comparing the predicted DMA behavior with the experimental data.展开更多
A dynamic object behavior model based on computational reflection is proposed. This model consists of function level and meta level, the meta objects in meta level manage the base objects and behaviors in function lev...A dynamic object behavior model based on computational reflection is proposed. This model consists of function level and meta level, the meta objects in meta level manage the base objects and behaviors in function level, including dynamic binding and unbinding of base object and behavior. We implement this model with RoleJava Language,which is our self linguistic extension of the Java Language.Meta Objects are generated automatically at compile\|time,this makes the reflecton mechanism transparent to programmers.Finally an example applying this model to a banking system is presented.展开更多
Ultra-high performance cement-based composites (UHPCC) is promising in construction of concrete structures that suffer impact and explosive loads.In this study,a reference UHPCC mixture with no fiber reinforcement and...Ultra-high performance cement-based composites (UHPCC) is promising in construction of concrete structures that suffer impact and explosive loads.In this study,a reference UHPCC mixture with no fiber reinforcement and four mixtures with a single type of fiber reinforcement or hybrid fiber reinforcements of straight smooth and end hook type of steel fibers were prepared.Split Hopkinson pressure bar (SHPB) was performed to investigate the dynamic compression behavior of UHPCC and X-CT test and 3D reconstruction technology were used to indicate the failure process of UHPCC under impact loading.Results show that UHPCC with 1% straight smooth fiber and 2% end hook fiber reinforcements demonstrated the best static and dynamic mechanical properties.When the hybrid steel fiber reinforcements are added in the concrete,it may need more impact energy to break the matrix and to pull out the fiber reinforcements,thus,the mixture with hybrid steel fiber reinforcements demonstrates excellent dynamic compressive performance.展开更多
The complexity of the loads acting on the offshore wind turbines (OWl's) structures and the significance of investigation on structure dynamics are explained. Test results obtained from a scaled wind turbine model ...The complexity of the loads acting on the offshore wind turbines (OWl's) structures and the significance of investigation on structure dynamics are explained. Test results obtained from a scaled wind turbine model are also summarized. The model is supported on monopile, subjected to different types of dynamic loading using an innovative out of balance mass system to apply cyclic/dynamic loads. The test results show the natural frequency of the wind turbine structure increases with the number of cycles, but with a reduced rate of increase with the accumulation of soil strain level. The change is found to be dependent on the shear strain level in the soil next to the pile which matches with the expectations from the element tests of the soil. The test results were plotted in a non-dimensional manner in order to be scaled to predict the orototvoe conseouences usin~ element tests of a soil usin~ resonant column aoDararus.展开更多
基金supported by the National Natural Science Foundation of China(Nos.51839009 and 52027814)the Natural Science Foundation of Hubei Province(No.2023AFB589).
文摘High-energy gas fracturing of shale is a novel,high efficacy and eco-friendly mining technique,which is a typical dynamic perturbing behavior.To effectively extract shale gas,it is important to understand the dynamic mechanical properties of shale.Dynamic experiments on shale subjected to true triaxial compression at different strain rates are first conducted in this research.The dynamic stress-strain curves,peak strain,peak stress and failure modes of shale are investigated.The results of the study indicate that the intermediate principal stress and the minor principal stress have the significant influence on the dynamic mechanical behaviors,although this effect decreases as the strain rate increases.The characteristics of compression-shear failure primarily occur in shale subjected to triaxial compression at high strain rates,which distinguishes it from the fragmentation characteristics observed in shale under dynamic uniaxial compression.Additionally,a numerical three-dimensional Split Hopkinson Pressure Bar(3D-SHPB),which is established by coupling PFC3D and FLAC3D methods,is validated to replicate the laboratory characteristics of shale.The dynamic mechanical characteristics of shale subjected to different confining stresses are systematically investigated by the coupling PFC3D and FLAC3D method.The numerical results are in good agreement with the experimental data.
文摘With rapid economic and social development in China, high-rise buildings have continuously sprung up since 2006. However, several big fire accidents in high-rise buildings such as the Beijing Television Cultural Center fire in 2009 and the Shanghai Jing'an District fire in 2010 etc. have claimed people's lives and caused huge amounts of economic and property losses,
基金supported by the National Key Research and Development Program of China (No.2018YFA0703500)the National Natural Science Foundation of China(Nos.52232006,52188101,52102153,52072029,51991340,and 51991342)+2 种基金the Overseas Expertise Introduction Projects for Discipline Innovation (No.B14003)the China Postdoctoral Science Foundation (No.2021M700379)the Fundamental Research Funds for Central Universities(No.FRF-TP-18-001C1)。
文摘Although the research history of triboelectrification has been more than 2000 years, there are still many problems to be solved so far.The use of scanning probe microscopy provides an important way to quantitatively study the transfer, accumulation, and dissipation of triboelectric charges in the process of triboelectrification. Two-dimensional materials are considered to be key materials for new electronic devices in the post-Moore era due to their atomic-scale size advantages. If the electrostatic field generated by triboelectrification can be used to replace the traditional gate electrostatic field, it is expected to simplify the structure of two-dimensional electronic devices and reconfigure them at any time according to actual needs. Here, we investigate the triboelectrification process of various two-dimensional materials such as MoS_(2), WSe_(2),and ZnO. Different from traditional bulk materials, after two-dimensional materials are rubbed, the triboelectric charges generated may tunnel through the two-dimensional materials to the underlying substrate surface. Because the tunneling triboelectric charge is protected by the twodimensional material, its stable residence time on the substrate surface can reach more than 7 days, which is more than tens of minutes for the traditional triboelectric charge. In addition, the electrostatic field generated by the tunneling triboelectric charge can effectively regulate the carrier transport performance of two-dimensional materials, and the source–drain current of the field effect device regulated by the triboelectric floating gate is increased by nearly 60 times. The triboelectric charge tunneling phenomenon in two-dimensional materials is expected to be applied in the fields of new two-dimensional electronic devices and reconfigurable functional circuits.
基金Supported by National Natural Science Foundation of China(Grant No.11072192)Shaanxi Provincial Industrial Technology Research Projects of China(Grant No.2015GY118)
文摘The beer game model is a typical paradigm used to study complex dynamics behaviours in production–distribution systems. The model, however, does not accord with current practical supply chain system models in discrete?type manufacturing industry, which are generally composed of retailers, distributors, manufacturers with internal sup?ply chain, and suppliers. To describe how ordering policies influence the complex dynamics behaviour modes and operating cost in a general discrete?type manufacturing industry supply chain system, a high dimension piecewise?linear dynamics model is built for the supply chain system. Five kinds of ordering policy combination are considered. The distribution of both the largest Lyapunov exponent of e ective inventory and average operating cost per cycle is obtained by simulation in a policy space. The simulation shows that for the general discrete?type manufacturing industry supply chain system, the upper chaotic corners emerge besides the lower chaotic corners in the policy space expressing the distribution of system behaviour mode, and that the ordering policies at each supply chain node as well as their combination have very significant e ect on the topology of the distribution of both system behaviour mode and operating cost in the policy space. We find that chaos is not always corresponding to high cost, and the "chaos amplification" is not completely relevant to the "cost amplification".
基金This work was supported by the National Science Fund for Distinguished Young Scholars of China (No.50125312) andSpecial Funds for Major State Basic Research Projects (No.G1999064800).
文摘Dynamic rheological characteristics of polypropylene (PP) filled with ultra-fine full-vulcanized powdered rubber (UFPR) composed of styrene-butadiene copolymer were studied through dynamic rheological measurements on an Advanced Rheometric Expansion System (ARES). A specific viscoelastic phenomenon, i.e. 'the second plateau', appeared at low frequencies, and exhibits a certain dependence on the amount of rubber particles and the dispersion state in the matrix. This phenomenon is attributed to the formation of aggregation structure of rubber particles. The analyses of Cole-Cole diagrams of the dynamic viscoelastic functions suggest that the heterogeneity of the composites is enhanced on increasing both particle content and temperature.
基金国家自然科学基金,Municipal Key Subject Program of Shanghai
文摘The radial symmetric motion problem was examined for a spherical shell composed of a class of imperfect incompressible hyper-elastic materials, in which the materials may be viewed as the homogeneous incompressible isotropic neo-Hookean material with radial perturbations. A second-order nonlinear ordinary differential equation that describes the radial motion of the inner surface of the shell was obtained. And the first integral of the equation was then carded out. Via analyzing the dynamical properties of the solution of the differential equation, the effects of the prescribed imperfection parameter of the material and the ratio of the inner and the outer radii of the underformed shell on the motion of the inner surface of the shell were discussed, and the corresponding numerical examples were carded out simultaneously. In particular, for some given parameters, it was proved that, there exists a positive critical value, and the motion of the inner surface with respect to time will present a nonlinear periodic oscillation as the difference between the inner and the outer presses does not exceed the critical value. However, as the difference exceeds the critical value, the motion of the inner surface with respect to time will increase infinitely. That is to say, the shell will be destroyed ultimately.
基金National Natural Science Foundation of China,Grant No.59895410
文摘The single-layer latticed cylindrical shell is one of the most widely adopted space-fl'amed structures.In this paper,free vibration properties and dynamic response to horizontal and vertical seismic waves of single-layer latticed cylindrical shells are analyzed by the finite element method using ANSYS software.In the numerical study,where hundreds of cases were analyzed,the parameters considered included rise-span ratio,length-span ratio,surface load and member section size.Moreover,to better define the actual behavior of single-layer latticed shells,the study is focused on the dynamic stress response to both axial forces and bending moments.Based on the numerical results,the effects of the parameters considered on the stresses are discussed and a modified seismic force coefficient method is suggested.In addition,some advice based on these research results is presented to help in the future design of such structures.
基金supported by National Natural Science Foundation of China (Grant No. 50575182)Research Fund for the Doctoral Program of Higher Education of China (Grant No. 20060699021)Shaanxi Provincial Natural Science Foundation of China (Grant No. 2009JM7002)
文摘Finger seal is a new technology developed for gas path sealing in gas turbine engine.It has been paid attention to its good sealing performance and lower manufacture cost.The vibration behavior of finger seal is not be considered in performance analysis for the contact finger seal with compliant geometric configuration,then this will influence the reliability of the performance analysis and the parametric design of a finger seal.According to the dynamic character of finger seal,the harmonic vibration and free vibration models of a repetitive section of a two-layer finger seal that contains one high and one low finger seal are established separately.The dynamic behavior of finger seal in different working conditions is obtained based on the dynamic response analysis of finger's vibrations.The dynamic low hysteresis and low wear terms based on the equivalent dynamic model of finger seal are put forward,which can be used to predict the dynamic behavior of finger seal.As an example,the dynamic behaviors of an 8-layer finger seal and a 10-layer finger seal were predicted,and the validity of the prediction was demonstrated by the leakage test results of these two finger seals.The work presented here not only could make the dynamic analysis of finger seal with complicated structure simple and easy especially for multi-layer finger seal system,but also suggest a useful method for designing the finger seal with good dynamic behavior by means of different seal layers assembly.
基金supported by the National Natural Science Foundation of China(No.11472179)
文摘The dynamic behavior of a bridge-erecting machine, carrying a moving mass suspended by a wire rope, is investigated. The bridge-erecting machine is modelled by a simply supported uniform beam, and a massless equivalent "spring-damper" system with an effective spring constant and an effective damping coefficient is used to model the moving mass suspended by the wire rope. The suddenly applied load is represented by a unitary Dirac Delta function. With the expansion method, a simple closed-form solution for the equation of motion with the replaced spring-damper-mass system is formulated. The characters of the rope are included in the derivation of the differential equation of motion for the system. The numerical examples show that the effects of the damping coefficient and the spring constant of the rope on the deflection have significant variations with the loading frequency. The effects of the damping coefficient and the spring constant under different beam lengths are also examined. The obtained results validate the presented approach, and provide significant references in the design process of bridgeerecting machines.
基金financially supported by the National Natural Science Foundation of China(Grant No.51679167 and 51979193)
文摘The marine risers are often subjected to parametric excitations from the fluctuation top tension. The top tension on the riser may fluctuate with multiple frequencies caused by irregular waves. In this paper, the influence between different frequency components in the top tension on the riser system is theoretically simulated and analyzed. With the Euler-Bernoulli beam theory, a dynamic model for the vibrations of the riser is established. The top tension is set as fluctuating with time and it has two different frequencies. The influences from the fluctuation amplitudes, circular frequencies and phase angles of these frequency components on the riser system are analyzed in detail. When these two frequencies are fluctuating in the stable regions, the riser system may become unstable because ω1+ω2≈2Ωn. The fluctuation amplitudes of these frequencies have little effect on the components of the vibration frequencies of the riser. For different phase angles, the stability and dynamic behaviors of the riser would be different.
基金the National Key Research and Development Program(2019YFB2006500)National Natural Science Foundation of China(51404082).
文摘In this paper,(500 nm 1%+5μm 3%)bimodal scale Al2O3p/AZ31 composites was fabricated by solid state synthesis and the effect of bimodal scale Al2O3 particulates on its dynamic recrystallization behavior and mechanical properties was investigated.The optical microscopy,scanning electron microscopy,transmission electron microscopy and electron universal strength tester composites were used to characterize the composites.The results indicate that the grains size of the composites are significantly refined and the mechanical properties are obviously improved.Due to the presence of the bimodal scale Al2o3 particulates,the high-density dislocation zone is formed around nano-Al2o3p and the particle deformation zone is formed near micron-ABOap.These zones are ideal sites for the formation of recrystallization nucleus.Meanwhile,the addition of the bimodal scale Al2o3 particulates may delay or hinder the growth of matrix grain through the pining effect on the grain boundaries,resulting in significantly improving the yield strength and tensile strength of Al2O3p/AZ31 composites.
文摘The study on rheological properties of a series of mica-filled polypropylene ( PP ) composites was carried out. The influence of surface-treatment of mica particles on dynamic rheological behavior of the composites were dealt with. The viscosity ( h ) and dynamic modulus ( G ) of the composite melts were higher than those of PP matrix, especially those for systems treated with silane, which was attributed to the interfacial adhesion enhancement. However, surface-treatment of mica by titanate resulted in lower h and G, as compared with the treatment by silane. The reason for this is believed to be the formation of the mono-molecular layer on the mica surface.
基金supported by Zhejiang Provincial Natural Science Foundation of China(R503223)
文摘The dynamic mechanical behavior of a novel polymeric composite damping material has been investigated in this article. The composite consists of chlorinated polyethylene (CPE), N,N-dicyclohexyl-2-benzothiazolylsufenamide (DZ), 4,4'-thio-bis(3-methyl-6-tert-buthylphenol) (BPSR) and vapor-grown carbon fiber (VGCF). It is found that either the position or the intensity of damping peak can be controlled by changing the composition of CPE/DZ/BPSR composite. Within a certain composition region, damping peak maximum depends on CPE/DZ ratio, whereas damping peak position is controlled by BPSR content. Moreover, the improvement of storage modulus can be achieved by incorporation of VGCF. These results may imply that a damping material possessing both good damping properties and high strength can be designed and obtained.
基金supported by the National Natural Science Foundation of China(11361053,11201204,11471148,11471330,145RJZA112)
文摘In this article, we consider positive steady state solutions and dynamics for a spatially heterogeneous predator-prey system with modified Leslie-Gower and Holling-Type II schemes. The heterogeneity here is created by the degeneracy of the intra-specific pressures for the prey. By the bifurcation method, the degree theory, and a priori estimates, we discuss the existence and multiplicity of positive steady states. Moreover, by the comparison argument, we also discuss the dynamical behavior for the diffusive predator-prey system.
基金supported by the National Natural Science Foundation of China(No.11372068)the National Key Basic Research and Development Program of China(973 Program)(No.2014CB-744104)
文摘The dynamical behavior of two tethered rigid spheres in a supersonic flow is numerically investigated. The tethered lengths and radius ratios of the two spheres are different. The two spheres, which are centroid axially aligned initially, are held stationary first, then released, and subsequently let fly freely in a supersonic flow. The mean qualities of the system and the qualities of the bigger sphere are considered and compared with the situations without the tether. In the separation process, six types of motion caused by the spheres, tether, and fluid interaction are found. The results show that the mean x-velocity of the system changes in a different manner for different radius ratios, and the x-velocity of the bigger sphere is uniformly reduced but through different mechanisms.
基金supported by the National Natural Science Foundation of China (No. 50571055).
文摘The dynamic mechanical behaviors of the Zr41Ti14Cu12.5Ni8Be22.5Fe2 bulk metallic glass (BMG) during continuous heating at a constant rate were investigated. The glass transition and crystallization of the Zr-based BMG were thus characterized by the measurements of storage modulus E′ and internal friction Q^-1. It was found that the variations of these dynamic mechanical quantities with temperature were interre-lated and were well in agreement with the DSC trace obtained at the same heating rate. The origin of the first peak in the internal friction curve was closely related to the dynamic glass transition and subsequent primary crystallization. Moreover, it can be well described by a physical model, which can characterize atomic mobility and mechanical response of disordered condense materials. In comparison with the DSC trace, the relative position of the first internal friction peak of the BMG was found to be dependent on its thermal stability against crys-tallization.
基金Supported by the National Natural Science Foundation of China(No.20490220)Open Fund of State Key Laboratory of Plastic Forming Simulation and Die & Mould Technology,China(No.05-10)+1 种基金Open Fund of Hubei Key Laboratory of Materials Chemistry and Service FailureProgram for New Century Excellent Talents in Universities of China(No.NCET-05-0640)
文摘Polypropylene(PP)/ethylene-octene copolymer(POE) blends were prepared with a twin-screw extruder.Their dynamic mechanical behavior were systematically investigated.The results show that PP/POE blends are heterogeneities with a partial compatible two-phase structure,the glass transition temperature of PP phases in the blends tends to shift towards high temperature with increasing the POE content,and the glass transition temperature of POE phases shifts towards the low temperature with increasing the PP content.The Kerner's dispersed phase model and co-continuous phase model can reasonably predict the visco-elasticity of PP/POE blends with different compositions.Additionally,the morphological structure of the blends can be estimated via comparing the predicted DMA behavior with the experimental data.
基金Supported by the National Natural Science Foundation of China(60373086)
文摘A dynamic object behavior model based on computational reflection is proposed. This model consists of function level and meta level, the meta objects in meta level manage the base objects and behaviors in function level, including dynamic binding and unbinding of base object and behavior. We implement this model with RoleJava Language,which is our self linguistic extension of the Java Language.Meta Objects are generated automatically at compile\|time,this makes the reflecton mechanism transparent to programmers.Finally an example applying this model to a banking system is presented.
基金Funded by the National Key Research and Development Program of China(No.2018YFC0705400)National Natural Science Foundation of China(No.51678142)the Fundamental Research Funds for the Central Universities。
文摘Ultra-high performance cement-based composites (UHPCC) is promising in construction of concrete structures that suffer impact and explosive loads.In this study,a reference UHPCC mixture with no fiber reinforcement and four mixtures with a single type of fiber reinforcement or hybrid fiber reinforcements of straight smooth and end hook type of steel fibers were prepared.Split Hopkinson pressure bar (SHPB) was performed to investigate the dynamic compression behavior of UHPCC and X-CT test and 3D reconstruction technology were used to indicate the failure process of UHPCC under impact loading.Results show that UHPCC with 1% straight smooth fiber and 2% end hook fiber reinforcements demonstrated the best static and dynamic mechanical properties.When the hybrid steel fiber reinforcements are added in the concrete,it may need more impact energy to break the matrix and to pull out the fiber reinforcements,thus,the mixture with hybrid steel fiber reinforcements demonstrates excellent dynamic compressive performance.
基金supported by the National Natural Science Foundation of China(51109184,51209183,and 51325901)
文摘The complexity of the loads acting on the offshore wind turbines (OWl's) structures and the significance of investigation on structure dynamics are explained. Test results obtained from a scaled wind turbine model are also summarized. The model is supported on monopile, subjected to different types of dynamic loading using an innovative out of balance mass system to apply cyclic/dynamic loads. The test results show the natural frequency of the wind turbine structure increases with the number of cycles, but with a reduced rate of increase with the accumulation of soil strain level. The change is found to be dependent on the shear strain level in the soil next to the pile which matches with the expectations from the element tests of the soil. The test results were plotted in a non-dimensional manner in order to be scaled to predict the orototvoe conseouences usin~ element tests of a soil usin~ resonant column aoDararus.