MULTIPLE SCATTERING THEORY OF EFFECTIVE MECHANICAL PROPERTIES OF INHOMOGENEOUS MEDIA

The rate of hydrothermal reaction of SiO_2 and/or A1_2O_3 in the system of CaO-Al_2O_3-SiO_2-H_2O at 200℃ and the factors which influence the reactions are investigated by determining the reaction ratio.The rate of reactions depends on the reactive activities of raw materials, initial composition of mixture and relative activity of SiO_2 and A12O3. The hydrothermal reaction can be accelerated by sodium hydroxide,in the case of silica,which has low activity, this is quite obvious.

Effect of Irradiation on Crystallinity and Mechanical Properties of Ultrahigh-Molecular-Weight Polyethylene

Ultrahigh-molecular-weight polyethylene(UtlMWPE) has been irradiated (0-40 Mrad) with a Co^(60) source at room temperature under vacuum. Their crystallinity has been investigated by DSC and SAXS A significant increase of heat of fusion can be seen at low irradiation doses, which is attributed to crystallization caused by chain scission during the process of irradiation. It is also observed that thickness of lamellae changes with irradiation dose. Young's modulus has been improved significantly after irradiation at low doses.

Effect of Trace Sc and Zr on the Mechanical Properties and Microstructure of A1 Alloy 2618

An experimental 2618(Al-Cu-Mg-Fe-Ni) alloy added with trace Sc and Zr was prepared by ingot metallurgy (IM) method. The aging behavior of the alloy was studied by Vickers hardness measurement at 200℃ and 300℃. and the tensile properties of alloy specimens were measured at 20℃, 200℃, 250℃ and 300℃. The microstructure was observed by using optical microscope, SEM and TEM. It was found that the addition of Sc and Zr to 2618 alloy resulted in a primary Al_3(Sc,Zr) phase which could refine the grain because it acts as nuclei of heterogeneous crystallization in the melt during solidification. The secondary Al_3(Sc,Zr) particles were full coherent with matrix and had obvious precipitation hardening effect. They also made the S' phase precipitate more homogeneous. So the strength of alloy increases at both ambient and elevated temperatures without a decrease of ductility. The ductile fracture of alloy occurs by microvoid nucleation, growth and coalescence, so the microvoid coalescence is the dominant fracture mechanism.

Effect of excitation current intensity on mechanical properties of ZL205A castings solidified under a traveling magnetic field

The effect of excitation current intensity on the mechanical properties of ZL205 A castings solidified under a traveling magnetic field was studied. The results of the experiment indicate that the excitation current intensity of the traveling magnetic field has a great influence on the mechanical properties of the ZL205 A castings. When the excitation current intensity is 15 A, the tensile strength and elongation of ZL205 A alloy castings increase 27.2% and 67.7%, respectively, compared with those of the same alloy solidified under gravity. The improvement of mechanical properties is attributed to the decrease of micro-porosity in the alloy. Under the traveling magnetic field, the feeding pressure in the alloy melt before solidification can be enhanced due to the electromagnetic force. Moreover, the melt flow induced by the traveling magnetic field can decrease the temperature gradient. The feeding resistance will be increased because the temperature gradient decrease. So traveling magnetic field has an optimum effect on feeding.

Effect of Mineral Oil on the Mechanical Properties and Fractographs of Fe_3(Al,Cr,Zr) Intermetallic Alloy

The effect of mineral oil on the mechanical properties and fractographs of Fe3(Al,Cr,Zr) in termetallic alloy has been investigated. The results show that the tensile ductility of the Fe3(Al,Cr,Zr) alloy tested in oil is comparable with the results obtained in oxygen and is in sensitive to strain rate. The fracture mode of the Fe3(Al,Cr,Zr) alloy treated at 700℃/1.5 h and tested in oil, is cleavage and with dimples in some areas.

Effects of A1 Additions on Microstructure and Mechanical Properties of MoSi_2

The effects of Al additions on the microstructure and mechanical properties of MoSi2 have been studied. With the A1 additions from 2.5 wt pct to 5 wt pct, the siliceous grain boundary phase in hot pressed samples was eliminated because of the formation of Al2O3 particles. It was shown that Al and SiO2 reacted at 860℃. During the reaction, A1 atoms were mainly transferred to Al2O3 particles, and to some extent, diffused into MoSi2 grains. Both the toughness and strength of Al containing composites exceeded those of pure MoSi2 material. Bending strength and fracture toughness reach the highest value of 350 MPa, 4.05 MPa.m1/2, respectively, at ambient temperature when Al addition was of 3.5 wt pct.

Effects of N on Electronic and Mechanical Properties of H-Type SiC

Structural, electronic and mechanical properties of the nH-SiC （n = 2, 4, 6, 8 and 10） polytypes are calculated by using the first-principles calculations based on the density-functional theory approach. The optimized lattice parameters of nH-SiC are in good agreement with the experimental data. The mechanical properties, including elastic constants, bulk modulus, Young＇s modulus, shear modulus and Poisson＇s ratio, are calculated. The analysis of elastic properties indicates that the effects of n on the mechanical properties of the five nil-SiC structures have no difference. The indirect band gap relationship for the live polytypes is Ebg2H 〉 Ebg4H 〉 Ebg6H 〉 Ebg10H 〉 EbgsH.

Microstructures and mechanical properties of ferrite-based lightweight steel with different compositions

The microstructures and mechanical properties of ferrite-based lightweight steel with different compositions were investigated by tensile test,scanning electron microscopy（SEM）,transmission electron microscopy（TEM）,X-ray diffraction（XRD）and thermodynamic calculation（TC）.It was shown that the ferrite-based lightweight steels with 5wt.%or 8wt.%Al were basically composed of ferrite,austenite andκ-carbide.As the annealing temperature increased,the content of the austenite in the steel gradually increased,while theκ-carbide gradually decomposed and finally disappeared.The mechanical properties of the steel with 5wt.%Al and 2wt.%Cr,composed of ferrite and Cr7C3carbide at different annealing temperatures,were significantly inferior to those of others.The steel containing 5wt.%Al,annealed at 820°C for 50sthen rapidly cooled to 400°C and held for 180s,can obtain the best product of strength and elongation（PSE）of 31242MPa·%.The austenite stability of the steel is better,and its PSE is higher.In addition,the steel with higher PSE has a more stable instantaneous strain hardening exponent（n value）,which is mainly caused by the effect of transformation induced plasticity（TRIP）.When theκ-carbide or Cr7C3carbide existed in the microstructure of the steel,there was an obvious yield plateau in the tensile curve,while its PSE decreased significantly.

Microstructure and Tensile Properties of a Nb–Mo Microalloyed 6.5Mn Alloy Processed by Intercritical Annealing and Quenching and Partitioning

The transformation behavior, microstructural evolution and mechanical properties were compared in a coldrolled Nb–Mo microalloyed 6.5Mn alloy after intercritical annealing（IA） and quenching and partitioning（Q ＆ P）,respectively. The thermodynamic calculation and theoretical analysis were used to determine the optimal heat treatment parameters. The Q ＆ P samples exhibited relatively higher strength with relatively low ductility, mainly due to the hard martensite matrix, which resulted in continuous yielding behavior upon loading, whereas the IA samples showed the significantly improved ductility, which benefited from the more sufficient transformation-induced plasticity（TRIP） effects and the softer ultrafine ferrite matrix. The dependence of yield point elongation（YPE） of IA samples on grain size demonstrated that the YPE value was in the reverse proportional relationship to the average grain size, which agreed well with theoretical analysis.

Electrical transport and current properties of rare-earth dysprosium Schottky electrode on p-type GaN at various annealing temperatures

The electrical and current transport properties of rapidly annealed Dy/p-GaN SBD are probed by I-V and C-V techniques. The estimated barrier heights（BH） of as-deposited and 200 ℃ annealed SBDs are 0.80 eV（I-V）/0.93 eV（C-V） and 0.87 eV（I-V）/1.03 eV（C-V）. However, the BH rises to 0.99 eV（I-V）/1.18 eV（C-V）and then slightly deceases to 0.92 eV（I-V）/1.03 eV（C-V） after annealing at 300 ℃ and 400 ℃. The utmost BH is attained after annealing at 300 ℃ and thus the optimum annealing for SBD is 300 ℃. By applying Cheung＇s functions, the series resistance of the SBD is estimated. The BHs estimated by I-V, Cheung＇s and ΨS-V plot are closely matched; hence the techniques used here are consistency and validity. The interface state density of the as-deposited and annealed contacts are calculated and we found that the NSS decreases up to 300 ℃ annealing and then slightly increases after annealing at 400 ℃. Analysis indicates that ohmic and space charge limited conduction mechanisms are found at low and higher voltages in forward-bias irrespective of annealing temperatures. Our experimental results demonstrate that the Poole-Frenkel emission is leading under the reverse bias of Dy/p-GaN SBD at all annealing temperatures.