Analysis of the effects of rising temperature for embankments under seismic loads in cold regions

The effect of temperature rising for frozen soil because of dynamic load was investigated by indoor tests.Roadway and railway embankments are always loaded by dynamic loads such as earthquakes and vehicles.Because the Qinghai-Tibetan Plateau is a re-gion where earthquakes occur frequently,it is essential to consider the temperature-rising effect of earthquakes or vehicles on railway and road embankment.In this paper and according to the theories of heat transfer and dynamic equilibrium equations,as-suming frozen soil as thermal elastic-viscoplastic material,taking the combination of thermal and mechanical stresses into account,we present the numerical formulae of this dynamic problem,and the computer program of the two-dimensional finite element is written.Using the program,the dynamic response analyses for embankments loaded by earthquake are worked out.Analysis in-dicated that the temperature-rising effect result from earthquakes for embankment in nonuniform distribution in some small areas,the maximum rising temperature is 0.16 ?C for consideration in this paper.

Dynamic Characteristics of Long -Span Steel -Concrete CompositeBeam Bridge Based on Vehicle -Bridge Coupling Effect

In order to investigate the effect of vehicle-bridge coupling on the dynamic characteristics of the bridge,a steel-concrete composite beam suspension bridge is taken as the research object,and a three-dimensional spatial model of the bridge and a biaxial vehicle model of the vehicle are established,and then a vehicle-bridge coupling vibration system is constructed on the basis of the Nemak-βmethod,and the impact coefficients of each part of the bridge are obtained under different bridge deck unevenness and vehicle speed.The simulation results show that the bridge deck unevenness has the greatest influence on the vibration response of the bridge,and the bridge impact coefficient increases along with the increase in the level of bridge deck unevenness,and the impact coefficient of the main longitudinal girder and the secondary longitudinal girder achieves the maximum value when the level 4 unevenness is 0.328 and 0.314,respectively;when the vehicle speed is increased,the vibration response of the bridge increases and then decreases,and the impact coefficient of the bridge in the middle of the bridge at a speed of 60 km/h achieves the maximum value of 0.192.

Traveling wave effect on the seismic response of a steel arch bridge subjected to near fault ground motions

In the 1990s, several major earthquakes occurred throughout the world, with a common observation that near fault ground motion （NFGM） characteristics had a distinct impact on causing damage to civil engineering structures that could not be predicted by using far field ground motions. Since then, seismic responses of structures under NFGMs have been extensively examined, with most of the studies focusing on structures with relatively short fundamental periods, where the traveling wave effect does not need to be considered. However, for long span bridges, especially arch bridges, the traveling wave （only time delay considered） effect may be very distinct and is therefore important. In this paper, the results from a case study on the seismic response of a steel arch bridge under selected NFGMs is presented by considering the traveling wave effect with variable apparent velocities. The effects of fling step and long period pulses of NFGMs on the seismic responses of the arch bridge are also discussed.

Seismic response analysis of continuous rigid frame bridge considering canyon topography effects under incident SV waves

To evaluate the importance of the canyon topography effects on large structures, based on a rigid frame bridge across a 137-m-deep and 600-m-wide canyon, the seismic response of the canyon site is analyzed using a two-dimensional finite element model under different seismic SV waves with the assumptions of vertical incidence and oblique incidence to obtain the ground motions, which are used as the excitation input on the pier foundations of the bridge with improved large mass method. The results indicate that canyon topography has significant influences on the ground motions in terms of inci- dent angle. The peak ground acceleration values vary greatly from the bottom of the canyon to the upper comers. Under ver- tical incident SV waves, at the upper comers of canyon the peak ground accelerations greatly increase; whereas the peak ground accelerations diminish at the bottom comers of canyon. Under oblique incident SV waves, the shaking of the canyon slope perpendicular to the incidence direction is much more severe than that of the opposite side of canyon. And the ground surface has been characterized by larger deformations in the case of oblique incident waves. It is also concluded that the low piers and frame of the continuous rigid frame bridge ape more sensitive to the multi-support seismic excitations than the flexible high piers. The canyon topography as well as the oblique incidence of the waves brings the continuous rigid frame bridge severe responses, which should be taken into account in bridge design.

Settlement characteristics of bridge approach embankment based on scale model test

In order to analyze the effects of backfill materials, geometries and slab setting on the settlement of bridge approach embankment, scale model was built based on the structural characteristics of bridge approach embankment, and scale model tests were carried out under different conditions. The results show that when graded gravels were selected as the backfill materials, the effect of setting approach slab to reduce the differential settlement is more prominent. When lime soils were selected as the backfill material, approach slab can moderate the longitudinal settlement slope. When using different backfill materials, the ultimate settlement of the positive trapezoidal backfill geometries is less than that of the inverted trapezoid, and the backfill geometries have little effect on the settlement slope.

On the Structure of the Arginine-carboxylate Salt Bridge:A Density Functional Theory Study

High level density functional theory (DFT) calculations are performed for the first time to answer the question whether the arginine-carboxylate salt bridge stays in a zwitterionic state or a neutral one. The results indicate that in the gas phase, the neutral form is more stable and hence proton transfer occurs from guanidinium to carboxylate. However, in an aqueous solution the zwitterionic form should be favored. The difference might he caused by the electrostatic interaction between the salt bridge and its molecular environment. Therefore, the solvation effect has to be considered in the modeling of proteins, whose stabilization depends heavily on the salt-bridges.

Theoretical and experimental study on shear lag effect of partially cable-stayed bridge

In order to resolve the traffic congestion problem, many cable-stayed bridges are designed with a large width to span ratio. This results in significant shear lag effect to cause nonuniform stress distribution along the flanges of the beam of bridge. This paper reports study on the shear lag effect of the Lanzhou Xiaoxihu Yellow River Bridge. A 3D finite element model of the bridge was developed and finite element analysis (FEA) was done to obtain the theoretical results. To evaluate the theoretical results, a scaled model was made to conduct static test in laboratory. The experiment results accorded with the results obtained by FEA. It is proved that FEA is an effective method to predict shear lag effect of bridges of this type.

Experimental analysis of additional aerodynamic effects caused by wind-driven rain on bridge main girder

To study the additional aerodynamic effect on a bridge girder under the action of wind-driven rain, the rainfall similarity considering raindrop impact and surface water is first given. Then, the dynamic characteristics and the process of vortex and flutter generation of the segment models under different rain intensities and angles of attack are tested by considering several typical main girder sections as examples. The test results indicate that the start and end wind speeds,interval length and number of vortex vibrations remain unchanged when it is raining, rainfall will reduce the windinduced vortex response. When test rain intensity is large, the decrease of amplitude is obvious. However, after considering the rain intensity similarity in this study, all of actual maximum rain intensities after conversion approach the domestic extreme rain intensity of approximately 709 mm/h. It can be observed that rainfall has a limited influence on the dynamic characteristics of the structure and vortex vibration response. When the test rain intensity is 120 mm/h, the critical wind speed of the model flutter increases by 20%-30%. However, after considering the rain intensity similarity ratio, the influence of rainfall on the wind-induced flutter instability of the bridge girder may be ignored.

Dynamic responses of bridge-approach embankment transition section of high-speed rail

Based on the vehicle track coupling dynamics theory, a new spatial dynamic numerical model of vehicle track subgrade coupling system was established considering the interaction among different structural layers in the subgrade system. The dynamic responses of the coupled system were analyzed when the speed of train was 350 km/h and the transition was filled with graded broken stones mixed with 5% cement. The results indicate that the setting form of bridge-approach embankment section has little effect on the dynamic responses, thus designers can choose it on account of the practical circumstances. Because the location about 5 m from the bridge abutment has the greatest deformation, the stiffness within 0 5 m zone behind the abutment should be specially designed. The results of the study from vehicle track dynamics show that the maximum allowable track deflection angle should be 0.09% and the coefficient of subgrade reaction(K30) is greater than 190 MPa within the 0 5 m zone behind the abutment and greater than 150 MPa in other zones.

Thermal features of Qinghai-Tibet Railway Embankment with Crushed-stone Slope Protection in Permafrost Regions

The Embankment with Crushed-Stone Slope Protection(ECSSP) in permafrost regions is an effective measure to cool subgrade and protect permafrost.It can mitigate the engineering hazards of the Qinghai-Tibet railway in the permafrost regions. Considering the influence of the noctumal cold air during summer months in Qinghai-Tibet Plateau。

Topographic effects on seismic response of long-span rigid-frame bridge under SV seismic wave

Seismic ground motions of two neighboring mountains and the free surface between them are calculated under the SV seismic waves with three different incident angles. The results are then taken as the inputs of multi-point seismic excitations for the foundation of a long-span bridge built over the valley in the analysis considering the integrated influence of traveling wave and topography. On the basis of a dynamic analytical method, a finite element model is created for the seismic responses of a four-span rigid-frame bridge of 440 m. The pier-top displacement and the pier-bottom internal force of the bridge are calculated. Then the results are compared with those considering traveling-wave effect only. The conclusions can serve as a seismic design reference for the structures located on the complex mountain topography.

Thermomechanical analysis of long-term global modal and local deformation measurements of the Kishwaukee Bridge using the bootstrap

In this paper we present a comparative analysis of global frequency and local deformation data for a large concrete bridge. The asymptotic probability distributions of the central statistics are presented, and compared with empirical bootstrap estimates. Bootstrapped distributions are calculated from reference data obtained during 1999–2000 and used to develop change-point alarm criteria for the structure, using reasonable sensitivity measures developed from FEM simulations and structural analysis. The implications of the frequency data are discussed in conjunction with the strain and displacement measurements in order to discern if the load carrying capacity of the bridge has been affected. The critical need for more advanced temperature compensation models for large structures continually in thermal disequilibrium is discussed.

Seismic response of the long-span steel truss arch bridge with the thrust under multidimensional excitation

Purpose–Under different ground motion excitation modes,the spatial coupling effect of seismic response for the arch bridge with thrust,seismic weak parts and the internal force components of the control section of main arch ribs are analyzed.Design/methodology/approach–Taking a 490 m deck type railway steel truss arch bridge as the background,the dynamic calculation model of the whole bridge was established by SAP2000 software.The seismic response analyses under one-,two-and three-dimension(1D,2D and 3D)uniform ground motion excitations were carried out.Findings–For the steel truss arch bridge composed of multiple arch ribs,any single direction ground motion excitation will cause large axial force in the chord of arch rib.The axial force caused by transverse and vertical ground motion excitation in the chord of arch crown area is 1.4–3.6 times of the corresponding axial force under longitudinal seismic excitation.The in-plane bending moment caused by the lower chord at the vault is 4.2–5.5 times of the corresponding bending moment under the longitudinal seismic excitation.For the bottom chord of arch rib,the arch foot is the weak part of earthquake resistance,but for the upper chord of arch rib,the arch foot,arch crown and the intersection of column and upper chord can all be the potential earthquake-resistant weak parts.The normal stress of the bottom chord of the arch rib under multidimensional excitation is mainly caused by the axial force,but the normal stress of the upper chord of the arch rib is caused by the axial force,in-plane and out of plane bending moment.Originality/value–The research provides specific suggestions for ground motion excitation mode and also provides reference information for the earthquake-resistant weak part and seismic design of long-span deck type railway steel truss arch bridges.

A STUDY ON THE STRUCTURAL EFFECT OF DOUBLE BRIDGES CONJUGATED SYSTEMS I.CARBONYL-IMINO SYSTEM

The struetural effect of the conjugative system(C)with carbonyl-imino bridges has been studied.The results show that:In the conjugated system(C),there is no electronic absorption peak attributable to the whole system,but there are three π-π* bands each nt which displays chacactecistics of its own independently.These indicate that the two bridges-carbonyl-and-imino-can block the tlanSmlSSion of the conjngative polarization of the whole system,so as to form three segments,this is verified by means of chemical synthesis and degradation.

Theoretical Analysis and Computer Simulation of Different Balance Bridge Voltage Controlled Crystal Oscillator

Q -double effect of different balance bridge voltage controlled crystal oscillator (DBVCXO) is quantitatively analysed by the computer simulation

The coupling effect of air-bridges on broadband spiral inductors in SiC-based MMIC technology

The coupling effect of air-bridges on broadband spiral inductors in SiC-based MMIC technology has been investigated deeply. The fabricated 1-nH spiral inductor on SiC substrate demonstrates a self-resonant frequency of 51.6 GHz, with a peak Q-fact of 12.14 at 22.1 GHz. From the S-parameters measurements, the exponential decay phenomenon is observed for L, Q-factor, and SRF with the air-bridge height decreasing, and an analytic expression is concluded to exactly fit the measured data which can be used to predict the performance of the spiral inductor. All the coefficients in the formula have specific meaning. By means of establishing the lumped model, the parasitic coupling capacitance of the air-bridge has been extracted and presents the exponential decay with the air-bridge heights decreasing which indicates that this capacitor is directly related to the coupling effect of the air-bridge. Through the electromagnetic field distribution simulation, the details of the electric field around the air-bridge have been presented which demonstrate the formation and the variation principles of the coupling effect.

Identification of Connection Flexibility Effects Based on Load Testing of a Steel-Concrete Bridge

In the case of composite girders, an effective cooperation of both parts of the section is influenced by deformability of connectors. Limited flexural stiffness of welded studs, used commonly in bridge structures, does not provide full interaction of a steel beam and a concrete slab. This changes strain distribution in cross-sections of a composite girder and results in redistribution of internal forces in steel and concrete element. In the paper partial interaction index defined on the basis of a neutral axis position, which can be used for verification of steel-concrete interaction in real bridge structures rather than in specimens is proposed. The range of the index value changes, obtained during load testing of a typical steel-concrete composite beam bridge, is presented. The investigation was carried out on a motorway viaduct, consisting of two parallel structures. During the testing values of strains in girders under static and quasi-static loads were measured. The readings from the gauges were used to determine the index, characterizing composite action of the girders. Results of bridge testing under movable load, changing position along the bridge span is presented and obtained in-situ influence functions of strains and index values are commented in the paper.

Pathways of Influence of the Northern Hemisphere Mid–high Latitudes on East Asian Climate: A Review

This paper reviews recent progress made by Chinese scientists on the pathways of influence of the Northern Hemisphere mid-high latitudes on East Asian climate within the framework of a“coupled oceanic-atmospheric(land-atmospheric or seaice-atmospheric)bridge”and“chain coupled bridge”.Four major categories of pathways are concentrated upon,as follows:Pathway A—from North Atlantic to East Asia;Pathway B—from the North Pacific to East Asia;Pathway C—from the Arctic to East Asia;and Pathway D—the synergistic effects of the mid-high latitudes and tropics.In addition,definitions of the terms“combined effect”,“synergistic effect”and“antagonistic effect”of two or more factors of influence or processes and their criteria are introduced,so as to objectively investigate those effects in future research.

In-situ testing study on convection and temperature characteristics of a new crushed-rock slope embankment design in a permafrost region

For the purpose of enhancing air convection and controlling solar radiation, a new crushed-rock slope embankment design combined with a sun-shade measure is proposed. A newly designed embankment was constructed in the Tuotuohe section of the Qinghai-Tibet Railway and a field-testing experiment was carried out to determine its convection and temperature characteristics. The results show that distinct air convection occurred in the crushed-rock layer of the new embankment, especially in cold seasons, which was enhanced when it flowed upwards along the slope. This preliminarily indicated that the new design of the embankment slope was good for reinforcing air convection in the crushed-rock layer. The frequent fluctuations of the convection speed and the environmental wind speed were in good agreement, suggesting that the convection in the crushed rock primarily came from the ambient wind. It was also preliminarily determined that the new embankment had a better cooling effect and sun-shade effect for decreasing the temperature of the embankment slope compared with a traditional crushed-rock slope embankment, and the mean temperature difference between them was up to 1.7 °C. The mean annual temperature at the bottom boundary of the crushed-rock layer was obviously lower than that at the top boundary, and heat flux calculation showed that the shallow soil beneath the embankment slope was weakly releasing heat, all of which indicated that the new embankment slope design was beneficial to the thermal stability of the embankment. This study is helpful in providing some references for improved engineering design and maintenance of roadbeds in permafrost regions.

Infl uence of structural parameters on dynamic characteristics and wind-induced buffeting responses of a super-long-span cable-stayed bridge

A 3D finite element （FE） model for the Sutong cable-stayed bridge （SCB） is established based on ANSYS. The dynamic characteristics of the bridge are analyzed using a subspace iteration method. Based on recorded wind data, the measured spectra expression is presented using the nonlinear least-squares regression method. Turbulent winds at the bridge site are simulated based on the spectral representation method and the FFT technique. The influence of some key structural parameters and measures on the dynamic characteristics of the bridge are investigated. These parameters include dead load intensity, as well as vertical, lateral and torsional stiffness of the steel box girder. In addition, the influence of elastic stiffness of the connection device employed between the towers and the girder on the vibration mode of the steel box girder is investigated. The analysis shows that all of the vertical, lateral and torsional buffeting displacement responses reduce gradually as the dead load intensity increases. The dynamic characteristics and the structural buffeting displacement response of the SCB are only slightly affected by the vertical and torsional stiffness of the steel box girder, and the lateral and torsional buffeting displacement responses reduce gradually as the lateral stiffness increases. These results provide a reference for dynamic analysis and design of super-long-span cable-stayed bridges.