Publisher Correction to:Highly Elastic,Bioresorbable Polymeric Materials for Stretchable,Transient Electronic Systems

Due to typesetting mistake,Hanul Min was missed to be denoted as a corresponding author in the article.The type-setter apologizes for this.The original article has been corrected.Open Access This article is licensed under a Creative Commons Attribution 4.0 International License,which permits use,sharing,adaptation,distribution and reproduction in any medium or format,as long as you give appropriate credit to the original author(s)and the source,provide a link to the Creative Commons licence,and indicate if changes were made.The images or other third party material in this article are included in the article’s Creative Commons licence,unless indicated otherwise in a credit line to the material.If material is not included in the article’s Creative Commons licence and your intended use is not permitted by statutory regulation or exceeds the permitted use,you will need to obtain permission directly from the copyright holder.

A novel relationship between elastic modulus and void ratio associated with principal stress for coral calcareous sand

Elastic moduli,e.g.shear modulus G and bulk modulus K,are important parameters of geotechnical materials,which are not only the indices for the evaluation of the deformation ability of soils but also the important basic parameters for the development of the constitutive models of geotechnical materials.In this study,a series of triaxial loading-unloading-reloading shear tests and isotropic loading-unloadingreloading tests are conducted to study several typical mechanical properties of coral calcareous sand(CCS),and the void ratio evolution during loading,unloading and reloading.The test results show that the stress-strain curves during multiple unloading processes are almost parallel,and their slopes are much greater than the deformation modulus at the initial stage of loading.The relationship between the confining pressure and the volumetric strain can be defined approximately by a hyperbolic equation under the condition of monotonic loading of confining pressure.Under the condition of confining pressure unloading,the evolution of void ratio is linear in the e-lnp0 plane,and these lines are a series of almost parallel lines if there are multiple processes of unloading.Based on the experimental results,it is found that the modified Hardin formulae for the elastic modulus estimation have a significant deviation from the tested values for CCS.Based on the experimental results,it is proposed that the elastic modulus of soils should be determined by the intersection line of two spatial surfaces in the G/K-e-p’/pa space(pa:atmosphere pressure).“Ye formulation”is further proposed for the estimation of the elastic modulus of CCS.This new estimation formulation for soil elastic modulus would provide a new method to accurately describe the mechanical behavior of granular soils.

Theoretical analysis of the elastic Kelvin-Helmholtz instability in explosive weldings

By considering the joint effects of the Kelvin-Helmholtz(KH) and Rayleigh-Taylor(RT) instabilities, this paper presents an interpretation of the wavy patterns that occur in explosive welding. It is assumed that the elasticity of the material at the interface effectively determines the wavelength, because explosive welding is basically a solid-state welding process. To this end, an analytical model of elastic hydrodynamic instabilities is proposed, and the most unstable mode is selected in the solid phase. Similar approaches have been widely used to study the interfacial behavior of solid metals in high-energy-density physics. By comparing the experimental and theoretical results, it is concluded that thermal softening,which significantly reduces the shear modulus, is necessary and sufficient for successful welding. The thermal softening is verified by theoretical analysis of the increase in temperature due to the impacting and sliding of the flyer and base plates, and some experimental observations are qualitatively validated.In summary, the combined effect of the KH and RT instabilities in solids determines the wavy morphology, and our theoretical results are in good qualitative agreement with experimental and numerical observations.

Linearized waveform inversion for vertical transversely isotropic elastic media:Methodology and multi-parameter crosstalk analysis

Seismic migration and inversion are closely related techniques to portray subsurface images and identify hydrocarbon reservoirs.Seismic migration aims at obtaining structural images of subsurface geologic discontinuities.More specifically,seismic migration estimates the reflectivity function(stacked average reflectivity or pre-stack angle-dependent reflectivity)from seismic reflection data.On the other hand,seismic inversion quantitatively estimates the intrinsic rock properties of subsurface formulations.Such seismic inversion methods are applicable to detect hydrocarbon reservoirs that may exhibit lateral variations in the inverted parameters.Although there exist many differences,pre-stack seismic migration is similar with the first iteration of the general linearized seismic inversion.Usually,seismic migration and inversion techniques assume an acoustic or isotropic elastic medium.Unconventional reservoirs such as shale and tight sand formation have notable anisotropic property.We present a linearized waveform inversion(LWI)scheme for weakly anisotropic elastic media with vertical transversely isotropic(VTI)symmetry.It is based on two-way anisotropic elastic wave equation and simultaneously inverts for the localized perturbations(ΔVp_(0)/Vp_(0)/Vs_(0)/Vs_(0)/,Δ∈,Δδ)from the long-wavelength reference model.Our proposed VTI-elastic LWI is an iterative method that requires a forward and an adjoint operator acting on vectors in each iteration.We derive the forward Born approximation operator by perturbation theory and adjoint operator via adjoint-state method.The inversion has improved the quality of the images and reduces the multi-parameter crosstalk comparing with the adjoint-based images.We have observed that the multi-parameter crosstalk problem is more prominent in the inversion images for Thomsen anisotropy parameters.Especially,the Thomsen parameter is the most difficult to resolve.We also analyze the multi-parameter crosstalk using scattering radiation patterns.The linearized waveform inversion for VTI-elastic media presented in this article provides quantitative information of the rock properties that has the potential to help identify hydrocarbon reservoirs.

Determining the effective elastic thickness through cross-correlation between isostatic disturbances

The elastic thickness parameter was estimated using the mobile correlation technique between the observed isostatic disturbance and the gravity disturbance calculated through direct gravimetric modeling. We computed the vertical flexure value of the crust for a specific elastic thickness using a given topographic dataset. The gravity disturbance due to the topography was determined after the calculation. A grid of values for the elastic thickness parameter was generated. Then, a moving correlation was performed between the observed gravity data(representing actual surface data) and the calculated data from the forward modeling. The optimum elastic thickness of the particular point corresponded to the highest correlation coefficient. The methodology was tested on synthetic data and showed that the synthetic depth closely matched the original depth, including the elastic thickness value. To validate the results, the described procedure was applied to a real dataset from the Barreirinhas Basin, situated in the northeastern region of Brazil. The results show that the obtained crustal depth is highly correlated with the depth from known models. Additionally, we noted that the elastic thickness behaves as expected, decreasing from the continent towards the ocean. Based on the results, this method has the potential to be employed as a direct estimate of crustal depth and elastic thickness for any region.

Hamiltonian system for the inhomogeneous plane elasticity of dodecagonal quasicrystal plates and its analytical solutions

A Hamiltonian system is derived for the plane elasticity problem of two-dimensional dodecagonal quasicrystals by introducing the simple state function. By using symplectic elasticity approach, the analytic solutions of the phonon and phason displacements are obtained further for the quasicrystal plates. In addition, the effectiveness of the approach is verified by comparison with the data of the finite integral transformation method.

Research on the flow stability and noise reduction characteristics of quasi-periodic elastic support skin

To enhance flow stability and reduce hydrodynamic noise caused by fluctuating pressure,a quasiperiodic elastic support skin composed of flexible walls and elastic support elements is proposed for fluid noise reduction.The arrangement of the elastic support element is determined by the equivalent periodic distance and quasi-periodic coefficient.In this paper,a dynamic model of skin in a fluid environment is established.The influence of equivalent periodic distance and quasi-periodic coefficient on flow stability is investigated.The results suggest that arranging the elastic support elements in accordance with the quasi-periodic law can effectively enhance flow stability.Meanwhile,the hydrodynamic noise calculation results demonstrate that the skin exhibits excellent noise reduction performance,with reductions of 10 dB in the streamwise direction,11 dB in the spanwise direction,and 10 dB in the normal direction.The results also demonstrate that the stability analysis method can serve as a diagnostic tool for flow fields and guide the design of noise reduction structures.

Analytical solution for the effective elastic properties of rocks with the tilted penny-shaped cracks in the transversely isotropic background

Seismic prediction of cracks is of great significance in many disciplines,for which the rock physics model is indispensable.However,up to now,multitudinous analytical models focus primarily on the cracked rock with the isotropic background,while the explicit model for the cracked rock with the anisotropic background is rarely investigated in spite of such case being often encountered in the earth.Hence,we first studied dependences of the crack opening displacement tensors on the crack dip angle in the coordinate systems formed by symmetry planes of the crack and the background anisotropy,respectively,by forty groups of numerical experiments.Based on the conclusion from the experiments,the analytical solution was derived for the effective elastic properties of the rock with the inclined penny-shaped cracks in the transversely isotropic background.Further,we comprehensively analyzed,according to the developed model,effects of the crack dip angle,background anisotropy,filling fluid and crack density on the effective elastic properties of the cracked rock.The analysis results indicate that the dip angle and background anisotropy can significantly either enhance or weaken the anisotropy degrees of the P-and SH-wave velocities,whereas they have relatively small effects on the SV-wave velocity anisotropy.Moreover,the filling fluid can increase the stiffness coefficients related to the compressional modulus by reducing crack compliance parameters,while its effects on shear coefficients depend on the crack dip angle.The increasing crack density reduces velocities of the dry rock,and decreasing rates of the velocities are affected by the crack dip angle.By comparing with exact numerical results and experimental data,it was demonstrated that the proposed model can achieve high-precision estimations of stiffness coefficients.Moreover,the assumption of the weakly anisotropic background results in the consistency between the proposed model and Hudson's published theory for the orthorhombic rock.

Dynamic characteristics of multi-span spinning beams with elastic constraints under an axial compressive force

A theoretical model for the multi-span spinning beams with elastic constraints under an axial compressive force is proposed.The displacement and bending angle functions are represented through an improved Fourier series,which ensures the continuity of the derivative at the boundary and enhances the convergence.The exact characteristic equations of the multi-span spinning beams with elastic constraints under an axial compressive force are derived by the Lagrange equation.The efficiency and accuracy of the present method are validated in comparison with the finite element method(FEM)and other methods.The effects of the boundary spring stiffness,the number of spans,the spinning velocity,and the axial compressive force on the dynamic characteristics of the multi-span spinning beams are studied.The results show that the present method can freely simulate any boundary constraints without modifying the solution process.The elastic range of linear springs is larger than that of torsion springs,and it is not affected by the number of spans.With an increase in the axial compressive force,the attenuation rate of the natural frequency of a spinning beam with a large number of spans becomes larger,while the attenuation rate with an elastic boundary is lower than that under a classic simply supported boundary.

Design and fabrication of compound varifocal lens driven by polydimethylsiloxane film elastic deformation

A compound varifocal lens based on electromagnetic drive technology is designed and fabricated, where the polydimethylsiloxane(PDMS) film acts as a driving component, while the PDMS biconvex lens and the plane-concave lens form a coaxial compound lens system. The plane-concave lens equipped with driving coils is installed directly above the PDMS lens surrounded by the annular magnet. When different currents are applied, the annular magnet moves up and down, driving the PDMS film to undergo elastic deformation, and then resulting in longitudinal movement of the PDMS lens. The position change of the PDMS lens changes the focal length of the compound lens system. To verify the feasibility and practicability of this design, a prototype of our compound lens system is fabricated in experiment. Our proposed compound lens shows that its zoom ability reaches 9.28 mm when the current ranges from -0.20 A to 0.21 A.

Impacts of artificial dams on terrestrial water storage changes and the Earth's elastic load response during 1950-2016: A case study of medium and large reservoirs in Chinese mainland

The construction of dams for intercepting and storing water has altered surface water distributions, landsea water exchanges, and the load response of the solid Earth. The lack of accurate estimation of reservoir properties through the land surface and hydrological models can lead to water storage simulation and extraction errors. This impact is particularly evident in many artificial reservoirs in China. The study aims to comprehensively assess the spatiotemporal distribution and trends of water storage in medium and large reservoirs(MLRs) in Chinese mainland during 1950-2016, and to investigate the gravity,displacement, and strain effects induced by the reservoir mass concentration using the load elasticity theory. In addition, the impoundment contributions of MLRs to the relative sea level changes were assessed using a sea-level equation. The results show impoundment increases in the MLRs during1950-2016, particularly in the Yangtze River(Changjiang) and southern basins, causing significant elastic load effects in the surrounding areas of the reservoirs and increasing the relative sea level in China's offshore. However, long-term groundwater estimation trends are overestimated and underestimated in the Yangtze River and southwestern basins, respectively, due to the neglect of the MLRs impacts or the uncertainty of the hydrological model's output(e.g., soil moisture, etc.). The construction of MLRs may reduce the water mass input from land to the ocean, thus slowing global sea level rise. The results of the impact of human activities on the regional water cycle provide important references and data support for improving the integration of hydrological models, evaluating Earth's viscoelastic responses under longterm reservoir storage, enhancing in-situ and satellite geodetic measurements, and identifying the main factors driving sea level changes.

Evaluation of soil fabric using elastic waves during load-unload

It is essential to assess the evolution of soil fabric as it has an important role in the mechanical responses of soils during complex loading conditions.This contribution carries out the physical experiments using three granular materials in the laboratory.The variations of compression and shear wave velocities(Vp and Vs)are investigated during load-unload cycles under dry and drained conditions.Supplementary discrete element method(DEM)simulations are performed to understand the evolution of soil fabric during the equivalent load-unload cycles using spherical particles.Vp and Vs are not always reversible even though the stress state regains its isotropic condition after unload,indicating that Vp and Vs are governed by not only the stress state but also the fabric change.The variations of Vp/Vs are density-and stress-dependent;a higher level of stress ratio(s01/s03)threshold is observed for denser packings to trigger a significant change in wave velocity ratio(Vp/Vs)for experimental results using spherical glass beads and simulation data using spherical particles.Considering the particle shape,a higher s01/s03 threshold is found for more angular particles than rounded particles.The DEM result reveals that Vp/Vs of spherical particles can be correlated linearly with the evolution of fabric ratio(Fver/Fhor)during loadunload in a pre-peak range under dry and drained conditions.

Laboratory insights into the effects of methane hydrate on the anisotropic joint elastic-electrical properties in fractured sandstones

Fractured hydrate-bearing reservoirs show significantly anisotropic geophysical properties. The joint application of seismic and electromagnetic explorations is expected to accurately assess hydrate resources in the fractured reservoirs. However, the anisotropic joint elastic-electrical properties in such reservoirs that are the key to the successful application of the joint explorations, remain poorly understood. To obtain such knowledge, we designed and implemented dedicated laboratory experiments to study the anisotropic joint elastic-electrical properties in fractured artificial silica sandstones (with fracture density of about 6.2%, porosity of approximately 25.7%, and mean grainsize of 0.089 mm) with evolving methane hydrate. The experimental results showed that the anisotropic compressional wave velocities respectively increased and decreased with the forming and dissociating hydrate, and the variation in the increasing trend and the decreasing extent of the velocity perpendicular to the fractures were more significant than that parallel to the fractures, respectively. The experimental results also showed that the overall decreasing trend of the electrical conductivity parallel to the fractures was steeper than that perpendicular to the fractures during hydrate formation, and the general variations of the two conductivities with complex trend were similar during hydrate dissociation. The variations in the elastic and electrical anisotropic parameters with forming and dissociating hydrate were also found to be distinct. Interpretation of the experimental results suggested that the hydrate binding to the grains evolved to bridge the surfaces of fractures when saturation exceeded 10% during hydrate formation, and the bridging hydrate gradually evolved to floating in fractures during dissociation. The experimental results further showed that the anisotropic velocities and electrical conductivities were correlated with approximately consistent trends of different slopes during hydrate formation, and the joint elastic-electrical anisotropic parameters exhibited a sharp peak at the hydrate saturation of about 10%. The results suggested that the anisotropic joint properties can be employed not only to accurately estimate hydrate saturation but also possibly to identify hydrate distribution in the fractures.

Monitoring the change in horizontal stress with multi-wave time-lapse seismic response based on nonlinear elasticity theory

Monitoring the change in horizontal stress from the geophysical data is a tough challenge, and it has a crucial impact on broad practical scenarios which involve reservoir exploration and development, carbon dioxide (CO_(2)) injection and storage, shallow surface prospecting and deep-earth structure description. The change in in-situ stress induced by hydrocarbon production and localized tectonic movements causes the changes in rock mechanic properties (e.g. wave velocities, density and anisotropy) and further causes the changes in seismic amplitudes, phases and travel times. In this study, the nonlinear elasticity theory that regards the rock skeleton (solid phase) and pore fluid as an effective whole is used to characterize the effect of horizontal principal stress on rock overall elastic properties and the stress-dependent anisotropy parameters are therefore formulated. Then the approximate P-wave, SV-wave and SH-wave angle-dependent reflection coefficient equations for the horizontal-stress-induced anisotropic media are proposed. It is shown that, on the different reflectors, the stress-induced relative changes in reflectivities (i.e., relative difference) of elastic parameters (i.e., P- and S-wave velocities and density) are much less than the changes in contrasts of anisotropy parameters. Therefore, the effects of stress change on the reflectivities of three elastic parameters are reasonably neglected to further propose an AVO inversion approach incorporating P-, SH- and SV-wave information to estimate the change in horizontal principal stress from the corresponding time-lapse seismic data. Compared with the existing methods, our method eliminates the need for man-made rock-physical or fitting parameters, providing more stable predictive power. 1D test illustrates that the estimated result from time-lapse P-wave reflection data shows the most reasonable agreement with the real model, while the estimated result from SH-wave reflection data shows the largest bias. 2D test illustrates the feasibility of the proposed inversion method for estimating the change in horizontal stress from P-wave time-lapse seismic data.

Elastic twisting metamaterial for perfect longitudinal-torsional wave mode conversion

In this work,we design a twisting metamaterial for longitudinal-torsional(L-T)mode conversion in pipes through exploring the theory of perfect transmodal FabryPerot interference(TFPI).Assuming that the axial and radial motions in pipes can be decoupled,we find that the metamaterial can be designed in a rectangular coordinate system,which is much more convenient than that in a cylindrical system.Numerical calculation with detailed microstructures shows that an efficient L-T mode conversion can be obtained in pipes with different radii.In addition,we fabricate mode-converting microstructures on an aluminum pipe and conduct ultrasonic experiments,and the results are in good agreement with the numerical calculations.We expect that the proposed LT mode-converting metamaterial and its design methodology can be applied in various ultrasonic devices.

The investigation of multiple factors on elastic anisotropy of artificial shale based on the orthogonal experiment

Elastic anisotropy of shales is critical to accurate constraints for rock physical models,quantitative interpretation and hydraulic fracturing.However,the causes of elastic anisotropy of shales are very complicated,and the understanding of how multiple influence factors affect the elastic anisotropy of shales is still not clear.Hence,the orthogonal experiment,as an effective multiple factors experimental method,is adopted in this study to analyze the effect of multiple factors for shale elastic anisotropy.Three factors,clay content,organic matter(OM)content and compaction stress are selected as independent variables,the orthogonal test table L_(16)(4^(3))with four levels for each factor is adopted.According to the designed orthogonal table,sixteen artificial shales are constructed based on the cold-pressing method,and all the dry artificial shales are measured by the ultrasonic measurements.The influence of each factor on the elastic anisotropy and the sensitivity orders of three factors are obtained using the range analysis.The orders of sensitivity for selected factors follow the sequence clay content>compaction stress>OM content for velocity anisotropy parameters.The compaction mechanism of artificial shales is also discussed by the compaction factor,which are positively correlated with the velocity anisotropy parameters.The clay platelets orientation distribution function(ODF)of samples is evaluated by a theoretical model,the ODF coefficients are significantly affected by the clay content and compaction stress,and W200 are much more sensitive to these factors than W400.The results can provide a critical rock physics basis for quantitative interpretation and reservoir prediction of the low-maturity or maturity shale reservoir.

Bubble nucleation in spherical liquid cavity wrapped by elastic medium

According to classical nucleation theory, gas nuclei can generate and grow into a cavitation bubble when the liquid pressure exceeds a threshold. However, classical nucleation theory does not include boundary effects. An enclosed spherical liquid cavity surrounded by elastic medium is introduced to model the nucleation process in tissue. Based on the equilibrium pressure relationship of a quasi-static process, the expressions of the threshold and the modified nucleation rate are derived by considering the tissue elasticity. It is shown that the constraint plays an important role in the nucleation process. There is a positive correlation between nucleation threshold pressure and constraint, which can be enhanced by an increasing tissue elasticity and reducing the size of the cavity. Meanwhile, temperature is found to be a key parameter of nucleation process, and cavitation is more likely to occur in confined liquids at temperature T > 100℃. In contrast, less influences are induced by these factors, such as bulk modulus, liquid cavity size, and acoustic frequency. Although these theoretical predictions of the thresholds have been demonstrated by many previous researches, much lower thresholds can be obtained in liquids containing dissolved gases, e.g., the nucleation threshold is about-21 MPa in a liquid of 0.8-nm gas nuclei at room temperature. Moreover, when there is a gas nucleus of 20 nm, the theoretical threshold pressure might be less than1 MPa.

Ni-P-SBR composite-electroless-plating enables Si anode with high conductivity and elasticity for high performance Li-ion batteries application

Silica-based anode is widely employed for high energy density Li-ion batteries owing to their high theoretical specific capacity(4200 m A h g-1).However,it is always accompanied by a huge volume expansion(300%)and shrinks during the lithiation/delithiation process,further leading to low cycle stability.Efforts to mitigate the adverse effects caused by volume expansion such as robust binder matrix,Coreshell structure,etc.,inevitably affect the electronic conductivity within the electrode.Herein,a high conductivity and elasticity Si anode(Ni-P-SBR(styrene-butadiene rubber)@Si)was designed and fabricated via the Ni-P-SBR composite-electroless-plating process.In this design,the Si particles are surrounded by SBR polymer and Ni particles,where the SBR can adapt to the volume change and Ni particles can provide the electrode with high electronic conductivity.Therefore,the Ni-P-SBR@Si delivers a high initial capacity of 3470 m A h g-1and presents capacity retention of 49.4%within 200 cycles at 600 m A g-1.Additionally,a high capacity of 1153 m A h g-1can be achieved at 2000 m A g-1and can be cycled stably under bending conditions.This strategy provides feasible ideas to solve the key issues that limit the practical application of Si anodes.

Low-frequency laboratory measurements of the elastic properties of solids using a distributed acoustic sensing system

In recent decades,low-frequency(LF)experiments based on the forced-oscillation(FO)method have become common practice in many rock physics laboratories for measuring the elastic and anelastic properties of rocks.However,the use of the electronic displacement sensors in traditional acquisition systems of FO devices such as conventional capacitive transducers or strain gauges seriously limits both the efficiency and productivity of LF measurements,and,due to the limited contact area of the displacement sensors with a sample under test,increases the requirements for sample homogeneity.In this paper,we present the first results obtained in the development of a new laboratory method elaborated to measure the elastic properties of solids.The method is a further development of the FO method where traditional data acquisition is replaced by acquisition based on fiber-optic distributed acoustic sensing(DAS)technology.The new method was tested in a laboratory study using two FO setups designed for measurements under uniaxial and confining pressures.The study was carried out on a sample made from polymethyl methacrylate(PMMA)and an aluminium standard,first under uniaxial pressure at FO frequencies of 1,10,30,60 and 100 Hz,and then under confining pressure at an FO frequency of 1 Hz.Both uniaxial and confining pressures were equal to 10 MPa,and the strain in the PMMA sample in all measurements did not exceed 4×10^(-8).The performance of DAS acquisition was compared with the measurements conducted at a strain of 1×10^(-6) using the traditional FO method based on the use of semiconductor strain gauges and the ultrasonic method.The results of the DAS measurements are in good agreement with the FO measurements carried out using semiconductor strain gauges and with the literature data.

A Wire-Driven Series Elastic Mechanism Based on Ultrasonic Motor for Walking Assistive System

In order to improve the elderly people's quality of life,supporting their walking behaviors is a promising technology.Therefore,based on one ultrasonic motor,a wire-driven series elastic mechanism for walking assistive system is proposed and investigated in this research.In contrast to tradition,it innovatively utilizes an ultrasonic motor and a wire-driven series elastic mechanism to achieve superior system performances in aspects of simple structure,high torque/weight ratio,quiet operation,quick response,favorable electromagnetic compatibility,strong shock resistance,better safety,and accurately stable force control.The proposed device is mainly composed of an ultrasonic motor,a linear spring,a steel wire,four pulleys and one rotating part.To overcome the ultrasonic motor's insufficient output torque,a steel wire and pulleys are smartly combined to directly magnify the torque instead of using a conventional gear reducer.Among the pulleys,there is one tailored pulley playing an important role to keep the reduction ratio as 4.5 constantly.Meanwhile,the prototype is manufactured and its actual performance is verified by experimental results.In a one-second operating cycle,it only takes 86 ms for this mechanism to output an assistive torque of 1.6 N·m.At this torque,the ultrasonic motor's speed is around 4.1 rad/s.Moreover,experiments with different operation periods have been conducted for different application scenarios.This study provides a useful idea for the application of ultrasonic motor in walking assistance system.