Improving the electrical performances of InSe transistors by interface engineering

InSe has emerged as a promising candidate for next-generation electronics due to its predicted ultrahigh electrical performance.However,the efficacy of the InSe transistor in meeting application requirements is hindered due to its sensitivity to interfaces.In this study,we have achieved notable enhancement in the electrical performance of InSe transistors through interface engineering.We engineered an InSe/h-BN heterostructure,effectively suppressing dielectric layer-induced scattering.Additionally,we successfully established excellent metal-semiconductor contacts using graphene ribbons as a buffer layer.Through a methodical approach to interface engineering,our graphene/InSe/h-BN transistor demonstrates impressive on-state current,field-effect mobility,and on/off ratio at room temperature,reaching values as high as 1.1 mA/μm,904 cm^(2)·V^(-1)·s^(-1),and>10~6,respectively.Theoretical computations corroborate that the graphene/InSe heterostructure shows significant interlayer charge transfer and weak interlayer interaction,contributing to the enhanced performance of InSe transistors.This research offers a comprehensive strategy to elevate the electrical performance of InSe transistors,paving the way for their utilization in future electronic applications.

Thermal performance of cast-in-place piles with artificial ground freezing in permafrost regions

During the construction of cast-in-place piles in warm permafrost,the heat carried by concrete and the cement hydration reaction can cause strong thermal disturbance to the surrounding permafrost.Since the bearing capacity of the pile is quite small before the full freeze-back,the quick refreezing of the native soils surrounding the cast-in-place pile has become the focus of the infrastructure construction in permafrost.To solve this problem,this paper innovatively puts forward the application of the artificial ground freezing(AGF)method at the end of the curing period of cast-in-place piles in permafrost.A field test on the AGF was conducted at the Beiluhe Observation and Research Station of Frozen Soil Engineering and Environment(34°51.2'N,92°56.4'E)in the Qinghai Tibet Plateau(QTP),and then a 3-D numerical model was established to investigate the thermal performance of piles using AGF under different engineering conditions.Additionally,the long-term thermal performance of piles after the completion of AGF under different conditions was estimated.Field experiment results demonstrate that AGF is an effective method to reduce the refreezing time of the soil surrounding the piles constructed in permafrost terrain,with the ability to reduce the pile-soil interface temperatures to below the natural ground temperature within 3 days.Numerical results further prove that AGF still has a good cooling effect even under unfavorable engineering conditions such as high pouring temperature,large pile diameter,and large pile length.Consequently,the application of this method is meaningful to save the subsequent latency time and solve the problem of thermal disturbance in pile construction in permafrost.The research results are highly relevant for the spread of AGF technology and the rapid building of pile foundations in permafrost.

Construction of core@double-shell structured energetic composites with simultaneously enhanced thermal stability and safety performance

The poor thermal stability and high sensitivity severely hinder the practical application of hexanitrohexaazaisowurtzitane(CL-20).Herein,a kind of novel core@double-shell CL-20 based energetic composites were fabricated to address the above issues.The coordination complexes which consist of natural polyphenol tannic acid(TA) and Fe~Ⅲ were chosen to construct the inner shell,while the graphene sheets were used to build the outer shell.The resulting CL-20/TA-Fe~Ⅲ/graphene composites exhibited simultaneously improved thermal stability and safety performance with only 1 wt% double-shell content,which should be ascribed to the intense physical encapsulation effect from inner shell combined with the desensitization effect of carbon nano-materials from outer shell.The phase transition(ε to γ) temperature increased from 173.70 ℃ of pure CL-20 to 191.87℃ of CL-20/TA-Fe~Ⅲ/graphene composites.Meanwhile,the characteristic drop height(H_(50)) dramatically increased from 14.7 cm of pure CL-20 to112.8 cm of CL-20/TA-Fe~Ⅲ/graphene composites,indicating much superior safety performance after the construction of the double-shell structure.In general,this work has provided an effective and versatile strategy to conquer the thermal stability and safety issues of CL-20 and contributes to the future application of high energy density energetic materials.

Flexible and Robust Functionalized Boron Nitride/Poly(p‑Phenylene Benzobisoxazole)Nanocomposite Paper with High Thermal Conductivity and Outstanding Electrical Insulation

With the rapid development of 5G information technology,thermal conductivity/dissipation problems of highly integrated electronic devices and electrical equipment are becoming prominent.In this work,“high-temperature solid-phase&diazonium salt decomposition”method is carried out to prepare benzidine-functionalized boron nitride(m-BN).Subsequently,m-BN/poly(pphenylene benzobisoxazole)nanofiber(PNF)nanocomposite paper with nacremimetic layered structures is prepared via sol–gel film transformation approach.The obtained m-BN/PNF nanocomposite paper with 50 wt%m-BN presents excellent thermal conductivity,incredible electrical insulation,outstanding mechanical properties and thermal stability,due to the construction of extensive hydrogen bonds andπ–πinteractions between m-BN and PNF,and stable nacre-mimetic layered structures.Itsλ∥andλ_(⊥)are 9.68 and 0.84 W m^(-1)K^(-1),and the volume resistivity and breakdown strength are as high as 2.3×10^(15)Ωcm and 324.2 kV mm^(-1),respectively.Besides,it also presents extremely high tensile strength of 193.6 MPa and thermal decomposition temperature of 640°C,showing a broad application prospect in high-end thermal management fields such as electronic devices and electrical equipment.

Investigating the Impact of Base Heating and External Electric Field on PV Cell Performance under Intense Illumination

The characterization of the performances of a PV cell is linked to intrinsic factors of this cell. It is therefore important for us to identify the favorable or unfavorable conditions that affect the performance of PV cells. It is from this perspective that it seems judicious to us to study the simultaneous influence of the heating of the base and an external electric field on the performance of a PV cell under intense illumination of 50 suns. Two phenomena contribute to the heating of the base of a PV cell which is heating due to the transfer by conduction of solar radiation energy received by the surface of the PV cell and the heat generated inside the PV cell by various phenomena linked to the movement of photogenerated charged carriers. In this study, we take into account the heating linked to the movement of the charged carriers in the base. After a mathematical modeling of the PV cell considered, some hypotheses are formulated and the expressions of the electrical parameters are established as a function of the electric field and base temperature. Subsequently, we use numerical simulation to highlight the behavior of theses parameters as a function of temperature and of the intensity of the electric field. The results show that for any given temperature, the orientation of the electric field as considered in our work improves the performance of the PV cell while high temperatures degrade these performances. Furthermore, the analysis of the curves shows that the harmful effect of temperature on the performance of a PV cell is more accentuated at large values of electric field.

Thermal Distortion Compensation for Improving Electrical Performance of Reflector Antennas

Aiming at the problem of the surface accuracy and electrical performance of the antenna in space environment are reduced due to thermal deformation caused by temperature load. This paper presents a method to compensate the thermally induced shape distortion of antenna reflector by actively adjusting actuators in order to improve the electrical performance. The adjustment of each actuator is related to the local deformation of the panel. Then, taking a space deployable antenna with a diameter of 5 meters as an example, the finite element model is established. According to the range of the temperature variation in space (−180°C - 200°C), different temperature loads are applied to the antenna. The variation of electrical properties and surface accuracy is analyzed and the worst working condition is determined, and the antenna is compensated based on this condition. Then, four different electrical performance parameters are used as the optimization objectives, and the electromechanical coupling optimization model is established, and the PSO algorithm is used to optimize the actuators adjustments. The results show that the method can effectively improve the electrical performance of the deformed reflector antenna.

Thermal and Electrical Properties of Liquid Metal Gallium During Phase Transition

Liquid metal gallium has been widely used in numerous fields, from nuclear engineering, catalysts, and energy storage to electronics owing to its remarkable thermal and electrical properties along with low viscosity and nontoxicity. Compared with high-temperature liquid metals, room-temperature liquid metals, such as gallium(Ga), are emerging as promising alternatives for fabricating advanced energy storage devices, such as phase change materials, by harvesting the advantageous properties of their liquid state maintained without external energy input. However, the thermal and electrical properties of liquid metals at the phase transition are rather poorly studied, limiting their practical applications. In this study, we reported on the physical properties of the solid–liquid phase transition of Ga using a custom-designed, solid–liquid electrical and thermal measurement system. We observed that the electrical conductivity of Ga progressively decreases with an increase in temperature. However, the Seebeck coefficient of Ga increases from 0.2 to 2.1 μV/K, and thermal conductivity from 7.6 to 33 W/(K·m). These electrical and thermal properties of Ga at solid–liquid phase transition would be useful for practical applications.

Improved RF power performance of InAlN/GaN HEMT by optimizing rapid thermal annealing process for high-performance low-voltage terminal applications

Improved radio-frequency(RF)power performance of InAlN/GaN high electron mobility transistor(HEMT)is achieved by optimizing the rapid thermal annealing(RTA)process for high-performance low-voltage terminal applications.By optimizing the RTA temperature and time,the optimal annealing condition is found to enable low parasitic resistance and thus a high-performance device.Besides,compared with the non-optimized RTA HEMT,the optimized one demonstrates smoother ohmic metal surface morphology and better heterojunction quality including the less degraded heterojunction sheet resistance and clearer heterojunction interfaces as well as negligible material out-diffusion from the barrier to the channel and buffer.Benefiting from the lowered parasitic resistance,improved maximum output current density of 2279 mA·mm^(-1)and higher peak extrinsic transconductance of 526 mS·mm^(-1)are obtained for the optimized RTA HEMT.In addition,due to the superior heterojunction quality,the optimized HEMT shows reduced off-state leakage current of 7×10^(-3)mA·mm^(-1)and suppressed current collapse of only 4%,compared with those of 1×10^(-1)mA·mm^(-1)and 15%for the non-optimized one.At 8 GHz and V_(DS)of 6 V,a significantly improved power-added efficiency of 62%and output power density of 0.71 W·mm^(-1)are achieved for the optimized HEMT,as the result of the improvement in output current,knee voltage,off-state leakage current,and current collapse,which reveals the tremendous advantage of the optimized RTA HEMT in high-performance low-voltage terminal applications.

Spray Effect on the Thermal Performances of a Dry Cooling Tower

Pre-cooling the inlet air of a dry cooling tower by means of a spray can improve the tower performance during periods of high temperature.To study the spray effect on the thermal performance of natural draft dry cooling towers(NDDCTs),in this study 3-D numerical simulations of such a process have been conducted using Fluent 16.2(a two-way coupled Eulerian-Lagrangian approach).The considered NDDCT is 120 m high and only half system is simulated due to its structural symmetry.Three different spray strategies have been investigated at a typical crosswind speed of 4 m/s,which is the most frequent wind speed.The results have shown that:(1)The three implemented spray strategies can improve the thermal performance of the studied NDDCT with a vary-ing degree of success.In one case,the heat rejection rate can be increased by 35.2%,and the tower outlet water temperature can be decreased by 2.1℃ when compared with the no spray case;(2)To improve the thermal per-formance of the NDDCT using a small amount of water,the design of the spray pre-cooling system must include more nozzles on the windward and fewer or even no nozzles on the leeward sides of the NDDCT.

Effect of Cerium on Mechanical Performance and Electrical Conductivity of Aluminum Rod for Electrical Purpose

The effect of rare earth element Ce on mechanical performance and electrical conductivity of aluminum rod for electrical purpose were studied under industrial production condition. Using optical microscope, SEM, TEM, EDS and X-ray diffractometer, the microstructure and phase composition of aluminum rod were measured and analyzed. The results indicate that the content of rare earth element Ce is between 0.05%～0.16% in the aluminum rod for electrical purpose. Its tensile strength is enhanced to some extent. The research also discovers that the tensile strength is enhanced remarkably with impurity element Si content increases. Because influence of Si is big to the conductivity, the Si content should be controlled continuously strictly in the aluminum for electrical purpose. Adding rare earth element Ce reduces the solid solubility of Si in the aluminum matrix, and the negative effect of Si on the aluminum conductor reduces effectively. So the limit of in Si content in aluminum rod for electrical purpose can be relaxed moderately.

Comparison of neutron irradiation effects on the electrical performances of SiGe HBT and SiBJT

The change of electrical performances of silicon-germanium (SiGe)heterojunction bipolar transistor (HBT) and Si bipolar junction transistor (BJT) was studied as afunction of reactor fast neutron radiation fluence. Alter neutron irradiation, the collector currentI_c and the current gain beta decrease, and the base current I_b increases generally for SiGe HBT.The higher the neutron irradiation fluence is, the larger I_b increases. For conventional Si BJT,I_c and I_b increase as well as beta decreases much larger than SiGe HBT at the same fluence. It isshown that SiGe HBT has a larger anti-radiation threshold and better anti-radiation performance thanSi BJT. The mechanism of performance changes induced by irradiation was preliminarily discussed.

Influential Factors on Deicing Performance of Electrically Conductive Concrete Pavement

The deicing experiment of carbon fiber reinforced electrically conductive concrete （CFRC） slab was conducted in laboratory at first, then the deicing process of CFRC parement was analyzed by means of finite element method （FEM）. At last, based on the energy conservation law and the computing restdts of finite element method, the influential factors including the setting of electric heating layer, environmental temperature, the thickness of ice, material parameters, and deicing power on deicing performance and energy consumption were discussed.

Testing results analysis of contact materials’electrical contact performance

Because of the different ways in which contact materials work, the basic requirements for silver metal oxide contact materials are different. They are anti-welded and anti-erosion when closed, anti-erosion when broken, and arc easily moved and have smaller contact resistance. In this paper, La2O3 is used as a stable oxide in contact material to replace CdO. A new type of Ag/SnO2-La2O3-Bi2O3 contact material is first obtained through using powder metallurgical method. Then electrical contact material parameter tester is used to test the electrical contact performance of the contact material. Through experiments, the arcing voltage and current curves, arcing energy curves, fusion power curves while broken and contact resistance while closed were obtained. Analysis of the results showed that the addition of La2O3 makes the contact material have the following advantages: smaller electrical wear, smaller arc energy, smaller contact resistance and arc is more easily extinguished.

Electrical Performance of Electron Irradiated SiGe HBT and Si BJT

The change of electrical performances of 1 MeV electron irradiated silicon-germanium (SiGe) heterojunction bipolar transistor (HBT) and Si bipolar junction transistor (BJT) was studied. After electron irradiation, both the collector current IC and the base current IB changed a little, and the current gain β decreased a little for SiGe HBT. The higher the electron irradiation fluence was, the lower the IC decreased. For conventional Si BJT, IC and IB increased as well as /? decreased much larger than SiGe HBT under the same fluence. The contribution of IB was more important to the degradation of β for both SiGe HBT and Si BJT. It was shown that SiGe HBT had a larger anti-radiation threshold and better anti-radiation performance than Si BJT. The mechanism of electrical performance changes induced by irradiation was preliminarily discussed.

Environmental Assessment and Dielectric Performances of the Secondary Electrical Insulation in Low Voltage Motors Impregnated by Different Techniques

A recent technique, using to potentially replace the conventional impregnating one in low voltage electric motors, has been studied in this communication. The conventional technique that uses?both primary and secondary insulations;?i.e.: enamel and varnish, has been compared to this recent technique which only uses one component,?i.e.: self-bonding wires. Self-bonding wires polymerization is very quick compared to that of the conventional technique. Environmental impact and both dielectric and mechanical properties of these two techniques have been estimated and compared. The goal is to estimate if this recent technique has not only a better environmental footprint but also good technical properties. The dielectric properties that have been measured are the dielectric strength and?the lifetime under pulse?voltage while mechanical consists in measuring the bonding strength that is crucial for impregnation.?For that purpose, a Life Cycle Assessment (LCA) that can simultaneously evaluatenumerous impacts on ground, water and air,?has been performed. The results show clearly that the recent technique significantly reduces the environmental footprint. Both mechanical and dielectric properties are then compared and analyzed.

Surface performance of workpieces processed by electrical discharge machining in gas

The surface performance of workpieces processed by electrical discharge machining in gas(dry EDM)was studied in this paper.Firstly,the composition,micro hardness and recast layer of electrical discharge machined(EDMed)surface of 45 carbon steels in air were investigated through different test analysis methods.The results show that the workpiece surface EDMed in air contains a certain quantity of oxide,and oxidation occurs on the workpiece surface.Compared with the surface of workpieces processed in kerosene,fewer cracks exist on the dry EDMed workpiece surface,and the surface recast layer is thinner than that obtained by conventional EDM.The micro hardness of workpieces machined by dry EDM method is lower than that machined in kerosene,and higher than that of the matrix.In addition,experiments were conducted on the surface wear resistance of workpieces processed in air and kerosene using copper electrode and titanium alloy electrode.The results indicate that the surface wear resistance of workpieces processed in air can be improved,and it is related with tool material and dielectric.

Synthesis and Characterization of Polyaniline/MgTiO_(3) Composite with Excellent Thermal and Electrochemical Performance

This article explores the effects of doping ferroelectric materials MgTiO_(3) with different proportions on the properties of polyaniline(PANI).PANI/MgTiO_(3) composites were prepared by in-situ composite method.Fourier transform infrared spectroscopy(FTIR)and X-ray diffraction(XRD)were used to characterize the structure of the composites.Scanning electron microscope(SEM)was used to characterize the morphology of the composites.The thermal stability of the composites was investigated by thermogravimetry(TG)and derivative thermogravimetry(DTG).Electrochemical methods(cyclic voltammetry(CV),electrochemical impedance spectroscopy(EIS),and constant current charge-discharge test)were used to compare and analyze the electrochemical performance of the composites.TG-DTG analysis and electrochemical experiments all show that the thermal stability and electrochemical properties of the PANI/MgTiO_(3) composite with a mass ratio of 82/18(w/w)are the best.The results indicate that there is a synergistic effect between PANI and MgTiO_(3),which improves the performances of the PANI when the appropriate amount of MgTiO_(3) is added.

Investigation of electrical performance of impregnation resin material for superconducting magnet

With the development of superconducting technology, the electrical performance of insulating materials is drawing increasing concern. This paper is devoted to investigating resin materials and aims to test the resin requirements of impregnating procedures and design curing molds. First, the samples are prepared, and then the power-frequency breakdown, lighting surges, relative dielectric constant, and loss angle tangent of the impregnation resin are measured at room temperature and liquid nitrogen temperature. We also present the testing reference for cryogenic and high-voltage insulating materials of superconducting power devices.

Model of Current Threshold for Perception in Testing Electrical Safety Performance

A generalized mathematical model of human body current threshold for perception was established and the current flowing through human body could be arbitrary cyclical waveforms.The relationship between human body current threshold for perception and current frequency, true root mean square(RMS) value and influence factor was described.A test system was established based on electroencephalogram(EEG) to study the relationship between human body current threshold for perception and current waveform, frequency and duty cycle so that the data could be obtained objectively and reliably.At least 850 groups of current threshold for perception and 16-lead EEGs were acquired.The theoretical analysis are verified by experimental data, and an amendment proposal on leakage current evaluation limits specified in International Electro-Technical Commission(IEC) standards is suggested.

Performance Survey of PVC Insulation of LC/Gecamines Electrical Cables Subjected to Ageing and Its Life Span Evaluation

Considering the insulators ageing in a mixture of PVC and dye, set following operating conditions and time to ensure proper operation and perfect safety of industrial installations using insulated conductors. The results showed that the insulation carried out by the L.C main office was a good quality (on thermal aspect), because the resistance of the insulation is so high (i.e. 3940 Mega Ohms under normal conditions). The results showed a lifespan of 50 years at a temperature of 40°C (close to ambient temperature), plus minus 33 years at a temperature of 70°C;plus minus 22 years at a temperature of 100°C and 12 years at a temperature of 160°C. Furthermore, information on chemical attack, the results showed that PVC cables have poor resistance to sulfuric acid attack (having a pH of 1.5 and a density of 1.84 g/cm3). LC/Gecamines is able to produce locally a good quality of electrical cables.