Synthesis and electro-optic properties of fluorine-containing polyimide

The fluorine-containing organic polymer was synthesized from 3, 3＇, 4, 4＇-Bisphenyltetracarboxylic （BPDA）, and 2,2-Bis （3-amino-4-hydroxyyphenyl） hexafluoropropane （6FHP）. It is a first-step preparation of a preimided hydroxy-containing polyimide, followed by the covalent bonding of an active chromophore, dispersed red 19 （DR19）, onto the backbone of the polyimide via the Mitsunobu reaction. The nonlinear optical （NLO） containing polyimide was synthesized. The differential scanning calorimeter （DSC）and thermal gravimetric analysis （TGA） exhibited Tg and the temperature Tg at which 5 % mass losses occurring of polymer were 248 and 309 ℃, respectively. A reflective electro-optic （EO） modulator using this polymer was fabricated. The optical nonlinearities were determined to be d33 = 5. 209×10^-9 esu （poling voltage of 3.6 kV, 205 ℃） and d33 =7. 418×10^-9esu （poling voltage of 3. 8 kV, 210 ℃） by the second harmonic generation method in in-situ condition at a fundamental wavelength of 1 064 nm. The EO coefficients 733 of the polymer layer in the EO modulator were determined to be 2. 182 pm/V （poling voltage of 3.6 kV, 205 ℃） and 3. 107 pm/V （poling voltage of 3.8 kV, 210 ℃） at 1064 nm by an attenuated-total-reflection （ATR） method.

A High-Performance Silicon Electro-Optic Phase Modulator with a Triple MOS Capacitor

We propose and analyze a novel Si-based electro-optic modulator with an improved metal-oxide-semiconductor （MOS） capacitor configuration integrated into silicon-on-insulator （SOl）. Three gate-oxide layers embedded in the silicon waveguide constitute a triple MOS capacitor structure, which boosts the modulation efficiency compared with a single MOS capacitor. The simulation results demonstrate that the Vπ Lπ product is 2. 4V · cm. The rise time and fall time of the proposed device are calculated to be 80 and 40ps from the transient response curve, respectively,indicating a bandwidth of 8GHz. The phase shift efficiency and bandwidth can be enhanced by rib width scaling.

Passive Q-Switching in a Flash-Lamp Pumped Nd∶YAG Laser with Ion-Implanted GaAs Wafer

A passive Q-switched flash-lamp-pumped Nd∶YAG laser with the ion-implanted semi-insulating GaAs wafer is reported.The wafer is implanted with 400keV As+ ions in the concentration of 10 16cm -2.Using GaAs wafer as an absorber and an output coupler,62ns pulse duration of single pulse is obtained.

Mach-Zehnder Electro-Optic Polymer Modulator with C orona Poled Core Layer

A Mach-Zehnder(MZ) electro-optic(EO) modulator are real iz ed,with three optical layers as polymer materials.The functional layer is the co rona poled crosslinkable polyurethane.The ridge waveguide is fabricated by using the spin-coating,poling,photolithography and oxygen reactive ion etching(RIE) techniques.The mode and the modulation properties of these devices are demonstra ted in a micron control system,while the light source works at the wavelength of 1 31 or 1 55 micron.

Experimental study of electro-optical-switched pulsed Nd:YAG laser

We report the specification of a compact and stable side diode-pumped Q-switched pulsed Nd：YAG laser. We ex- perimentally study and compare the performance of the pulsed Nd：YAG laser in the free-running and Q-switched modes at different pulse repetition rates from 1 Hz to 100 Hz. The laser output energy is stabilized by using a special configu- ration of the optical resonator. In this laser, an unsymmetrical concave-concave resonator is used and this structure helps the mode volume to be nearly fixed when the pulse repetition rate is increased. According to the experimental results in the Q-switched operation, the laser output energy is nearly constant around 70 mJ with an FWHM pulse width of 7 ns at 100 Hz. The optical-to-optical conversion efficiency in the Q-switched regime is 17.5%.

Electro-Optical Effect Measurement of Thin-Film Material Using PM Fiber Mach-Zehnder Interferometer

A polarization-maintaining （PM） fiber Mach-Zehnder （MZ） interferometer has been established to measure the EO effect of very thin film materials with optical anisotropy. Unlike a common MZ interferometer, all the components are connected via polarization-maintaining fibers. At the same time, a polarized DFB laser with a maximum power output of 10mW is adopted as the light source to induce a large extinction ratio. Here,we take it to determine the electro-optical coefficients of a very thin superlattice structure with GaAs, KTP, and GaN as comparative samples. The measured EO coefficients show good comparability with the others.

MoS_2 saturable absorber prepared by chemical vapor deposition method for nonlinear control in Q-switching fiber laser

Due to the remarkable carrier mobility and nonlinear characteristic, MoS2 is considered to be a powerful competitor as an effective optical modulated material in fiber lasers. In this paper, the MoS2 films are prepared by the chemical vapor deposition method to guarantee the high quality of the crystal lattice and uniform thickness. The transfer of the films to microfiber and the operation of gold plated films ensure there is no heat-resistant damage and anti-oxidation. The modulation depth of the prepared integrated microfiber-MoS2 saturable absorber is 11.07%. When the microfiber-MoS2 saturable absorber is used as a light modulator in the Q-switching fiber laser, the stable pulse train with a pulse duration of 888 ns at 1530.9 nm is obtained. The ultimate output power and pulse energy of output pulses are 18.8 mW and 88 nJ, respectively. The signal-to-noise ratio up to 60 dB indicates the good stability of the laser. This work demonstrates that the MoS2 saturable absorber prepared by the chemical vapor deposition method can serve as an effective nonlinear control device for the Q-switching fiber laser.

High-power electro-optic switch technology based on novel transparent ceramic

A novel high-power polarization-independent electro-optic switch technology based on a reciprocal structtire Sagnac interferometer and a transparent quadratic electro-optic ceramic is proposed and analyzed theoretically and experimentally. The electro-optic ceramic is used as a phase retarder for the clockwise and counter-clockwise polarized light, and their po- larization directions are adjusted to their orthogonal positions by using two half-wave plates. The output light then becomes polarization-independent with respect to the polarization direction of the input light. The switch characteristics, including splitter ratios and polarization states, are theoretically analyzed and simulated in detail by the matrix multiplication method. An experimental setup is built to verify the analysis and experimental results. A new component ceramic is used and a non- polarizing cube beam splitter （NPBS） replaces the beam splitter （BS） to lower the ON/OFF voltage to 305 V and improve the extinction ratio by 2 dB. Finally, the laser-induced damage threshold for the proposed switch is measured and discussed. It is believed that potential applications of this novel polarization-independent electro-optic switch technology will be wide, especially for ultrafast high-power laser systems.

Electro-optical properties cholesteric liquid of polymer stabilized crystal film＊

Liquid crystals （LCs） and polymers are extensively used in various electro-optical applications. In this paper, normal mode polymer stabilized cholesteric LC film is prepared and studied. The effects of chiral dopant and monomer concentrations on the electro-optical properties, such as contrast ratio, driving voltage, hysteresis width and response time, are investigated. The reasons of electro-optical properties influenced by the concentrations of the materials are discussed. Through the proper material recipe, the electro-optical properties of polymer stabilized cholesteric LC film can be optimized.

Recent progress in integrated electro-optic frequency comb generation

Optical frequency combs have emerged as an important tool enabling diverse applications from test-and-measurement,including spectroscopy,metrology,precision distance measurement,sensing,as well as optical and microwave waveform synthesis,signal processing,and communications.Several techniques exist to generate optical frequency combs,such as mode-locked lasers,Kerr micro-resonators,and electro-optic modulation.Important characteristics of optical frequency combs include the number of comb lines,their spacing,spectral shape and/or flatness,and intensity noise.While mode-locked lasers and Kerr micro-resonators can be used to obtain a large number of comb lines compared to electro-optic modulation,the latter provides increased flexibility in tuning the comb spacing.For some applications in optical communications and microwave photonics,a high degree of integration may be more desirable over a very large number of comb lines.In this paper,we review recent progress on integrated electro-optic frequency comb generators,including those based on indium phosphide,lithium niobate,and silicon photonics.

Organic electro-optic polymer materials and organic-based hybrid electro-optic modulators

High performance electro-optic modulator,as the key device of integrated ultra-wideband optical systems,have be-come the focus of research.Meanwhile,the organic-based hybrid electro-optic modulators,which make full use of the advant-ages of organic electro-optic(OEO)materials(e.g.high electro-optic coefficient,fast response speed,high bandwidth,easy pro-cessing/integration and low cost)have attracted considerable attention.In this paper,we introduce a series of high-perform-ance OEO materials that exhibit good properties in electro-optic activity and thermal stability.In addition,the recent progress of organic-based hybrid electro-optic devices is reviewed,including photonic crystal-organic hybrid(PCOH),silicon-organic hy-brid(SOH)and plasmonic-organic hybrid(POH)modulators.A high-performance integrated optical platform based on OEO ma-terials is a promising solution for growing high speeds and low power consumption in compact sizes.

Q-Switching Pulse Operation in 1.5-μm Region Using Copper Nanoparticles as Saturable Absorber

We demonstrate a passively Q-switched erbium-doped fiber laser （EDFL） using a copper nanoparticle （CuNP） thin film as the saturable absorber in a ring cavity. A stable Q-switched pulse operation is observed as the CuNP saturable absorber （SA） is introduced in the cavity. The pulse repetition rate of the EDFL is observed to be proportional to the pump power, and is limited to 101.2kHz by the maximum pump power of 113.7mW. On the other hand, the pulse width reduces from 10.19μs to 4.28μs as the pump power is varied from 26.1 mW to 113.7mW. The findings suggest that CuNP SA could be useful as a potential saturable absorber for the development of the robust, compact, efficient and low cost Q-switched fiber laser operating at 1.5-μm region.

Investigation of the mode splitting induced by electro-optic birefringence in a vertical-cavity surface-emitting laser by polarized electroluminescence

The mode splitting induced by electro-optic birefringence in a P-I-N InGaAs/GaAs/A1GaAs vertical-cavity surface- emitting laser （VCSEL） has been studied by polarized electroluminescence （EL） at room temperature. The polarized EL spectra with E｜｜[110] and E ｜｜ [150] directions, are extracted for different injected currents. The mode splitting of the two orthogonal polarized modes for a VCSEL device is determined, and its value increases linearly with the increasing injected current due to electro-optic birefringence; This article demonstrates that the polarized EL is a powerful tool to study the mode splitting and polarization anisotropy of a VCSEL device.

Electro-optical dual modulation on resistive switching behavior in BaTiO3/BiFeO3/TiO2 heterojunction

The novel BaTiO3/BiFeO3/TiO2 multilayer heterojunction is prepared on a fluorine-doped tinoxide(FTO) substrate by the sol–gel method. The results indicate that the Pt/Ba TiO3/BiFeO3/TiO2/FTO heterojunction exhibits stable bipolar resistive switching characteristic, good retention performance, and reversal characteristic. Under different pulse voltages and light fields, four stable resistance states can also be realized. The analysis shows that the main conduction mechanism of the resistive switching characteristic of the heterojunction is space charge limited current(SCLC) effect. After the comprehensive analysis of the band diagram and the P–E ferroelectric property of the multilayer heterojunction, we can deduce that the SCLC is formed by the effect of the oxygen vacancy which is controlled by ferroelectric polarizationmodulated change of interfacial barrier. And the effective photo-generated carrier also plays a regulatory role in resistance state(RS), which is formed by the double ferroelectric layer Ba TiO3/BiFeO3 under different light fields. This research is of potential application values for developing the multi-state non-volatile resistance random access memory(RRAM) devices based on ferroelectric materials.

Passive Q-Switching of a Yb:LuVO_4 Laser with Cr^(4+):YAG:Approaching the Intrinsic Upper Limit of Repetition Rate

We demonstrate a diode pumped Yb：LuVO4 laser that can be passively Q-switched by a Cr^（4＋）：YAG saturable absorber having an initial transmission as high as 99.3%.A maximum pulsed output power of 2.35 W is generated at a repetition rate of 285.7 kHz,approaching or very near the intrinsic upper limit imposed by the recovery time of the Cr^（4＋）：YAG saturable absorber,and the resulting pulse energy,duration and peak power are,respectively,8.2μJ,39.2ns and 0.209kW.

Electro-Optical Properties of Carbon Nanotubes Obtained by High Density Plasma Chemical Vapor Deposition

In this work, we studied the electro-optical properties of high-aligned carbon nanotubes deposited at room temperature. For this, we used the High Density Plasma Chemical Vapor Deposition system. This system uses a new concept of plasma generation: a planar coil is coupled to an RF system for plasma generation. This was used together with an electrostatic shield, for plasma densification, thereby obtaining high-density plasmas. The carbon nanotubes were deposited using pure methane plasmas. Three methods were used for the surface modification of the sample: reference substrate (silicon wafer only submitted to a chemical cleaning), silicon wafer with surface roughness generated by plasma etching, silicon wafer with a thin iron film and silicon wafer with diamond nano powder used as precursor materials. For each kind of silicon wafer surface, the carbon nanotubes were deposited with two different deposition times (two and three hours). The carbon nanotubes structural characteristics were analyzed by Atomic Force Microscope and Scanning Electronic Microscope. The carbon nanotubes electrical characteristics were observed by Raman Spectroscopy and the carbon nanotubes electro-optical properties were analyzed by current vs voltage electrical measurements and photo-luminescence spectroscopy measurements. The photoelectric effect in the carbon nanotubes were determined by photo-induced current measurements. In this work, we obtained carbon nanotubes with semiconductor properties and carbon nanotubes with metallic properties. The electro-optical effects depend strongly on the substrate preparation and the deposition parameters of the carbon nanotubes. The carbon nanotubes are high aligned and show singular properties that can be used for many applications.

Electro-optical properties of high birefringence liquid crystal compounds with isothiocyanate and naphthyl group

Liquid crystal（LC） compound with isothiocyanate and naphthyl group is an attractive high birefringence LC material,and can be used in optical devices. In this paper, the electro-optical properties of a series of this type of LC compounds were investigated. The melting points and enthalpy values of these LC compounds were higher than those of corresponding compounds with the phenyl group. These compounds exhibited high birefringence with a maximum value of 0.66. Fluorine substitution in the molecular almost does not affect the birefringence value. When these LC compounds with the naphthyl group were dissolved in a commercial LC mixture, the electro-optical properties depending on temperature were investigated. In the low-temperature region, LC mixtures with the naphthyl-group LC compounds exhibited higher viscosity than pure commercial LCs. In the high-temperature region, viscosity values very closely approached each other. When response performance was investigated, figure-of-merit（FoM） values were measured. The Fo M values of LC mixtures containing LC compounds with naphthyl group were lower than those of reference benzene LCs in the low-temperature region. However, in the high-temperature region, the results were reversed. These isothiocyanate LC compounds with naphthyl group can be applied in special fast-response LC device, particularly the ones used under high-temperature conditions.

Preparation and Microstructural,Structural,Optical and Electro-Optical Properties of La Doped Pmn-Pt Transparent Ceramics

Transparent relaxor ferroelectric ceramics of the system lanthanum modified lead magnesium niobate have been investigated for a variety of electro-optic properties could make these materials alternatives to (Pb,La)(Zr,Ti)O3. However, a study that relates the properties in function stoichiometric formula, it has not been analyzed heretofore. Therefore, in this work the effect of A-site substitution of La+3 in the characterization microstructural, structural, optical and electro-optical on (1-x)[Pb(1-3/2y)Lay(Mg1/3Nb2/3)O3]-xPbTiO3 and (1-z)[(1-x)Pb(Mg1/3Nb2/3)O3+xPbTiO3]+zLa2O3 has been performed. It was observed that the properties according to the stoichiometric formula and the PT had a maximum whose behavior was related to the addition of lanthanum in each stoichiometries.

Measurement of Frequency Shift Characteristics Based on LiNbO_3 Waveguide Electro-Optic Intensity Modulator

High-speed and wide-band LiNbO3 waveguide electro-optic intensity modulator has drawn great attention in the field of optical fiber communication and sensor. This paper reports the research results on the measurement of frequency shift characteristics of Mach-Zehnder electro-optic intensity modulator. Two measurement methods of frequency shift characteristics for high and low frequency modulations are studied in theory and experiment and demonstrate different results. The realization of a multi-wavelength optical source based on Mach-Zehnder electro-optic intensity modulator has been introduced. The technique to reach the maximum intensity for interesting shift frequency, particularly for heterodyne detection of Brillouin distributed optical fiber sensing, has been given.

High-speed 2 × 2 silicon-based electro-optic switch with nanosecond switch time

A 2 × 2 electro-optic switch is experimentally demonstrated using the optical structure of a Mach-Zehnder interferometer （MZI） based on a submicron rib waveguide and the electrical structure of a PIN diode on silicon-on-insulator （SOI）. The switch behaviour is achieved through the plasma dispersion effect of silicon. The device has a modulation arm of 1 mm in length and cross-section of 400 nm×340 nm. The measurement results show that the switch has a VπLπ figure of merit of 0.145 V.cm and the extinction ratios of two output ports and cross talk are 40 dB, 28 dB and -28 dB, respectively. A 3 dB modulation bandwidth of 90 MHz and a switch time of 6.8 ns for the rise edge and 2.7 ns for the fall edge are also demonstrated.