Electro-optical properties and(E,F) phase diagram of fluorinated chiral smectic liquid crystals

Fluorinated smectic liquid crystals each with a biphenyl benzoate rigid core are investigated. Molecular structures of the studied compounds have difference only in fluorine position and the length of the carbon chain. Dielectric relaxation study and electro-optical measurements are carried out with the classical SSFLC geometry. The field-induced phase transitions are studied and the（E,T） phase diagram is established.

Electro-optical properties cholesteric liquid of polymer stabilized crystal film＊

Liquid crystals （LCs） and polymers are extensively used in various electro-optical applications. In this paper, normal mode polymer stabilized cholesteric LC film is prepared and studied. The effects of chiral dopant and monomer concentrations on the electro-optical properties, such as contrast ratio, driving voltage, hysteresis width and response time, are investigated. The reasons of electro-optical properties influenced by the concentrations of the materials are discussed. Through the proper material recipe, the electro-optical properties of polymer stabilized cholesteric LC film can be optimized.

Electro-optical properties of high birefringence liquid crystal compounds with isothiocyanate and naphthyl group

Liquid crystal（LC） compound with isothiocyanate and naphthyl group is an attractive high birefringence LC material,and can be used in optical devices. In this paper, the electro-optical properties of a series of this type of LC compounds were investigated. The melting points and enthalpy values of these LC compounds were higher than those of corresponding compounds with the phenyl group. These compounds exhibited high birefringence with a maximum value of 0.66. Fluorine substitution in the molecular almost does not affect the birefringence value. When these LC compounds with the naphthyl group were dissolved in a commercial LC mixture, the electro-optical properties depending on temperature were investigated. In the low-temperature region, LC mixtures with the naphthyl-group LC compounds exhibited higher viscosity than pure commercial LCs. In the high-temperature region, viscosity values very closely approached each other. When response performance was investigated, figure-of-merit（FoM） values were measured. The Fo M values of LC mixtures containing LC compounds with naphthyl group were lower than those of reference benzene LCs in the low-temperature region. However, in the high-temperature region, the results were reversed. These isothiocyanate LC compounds with naphthyl group can be applied in special fast-response LC device, particularly the ones used under high-temperature conditions.

Electro-Optical Properties of Carbon Nanotubes Obtained by High Density Plasma Chemical Vapor Deposition

In this work, we studied the electro-optical properties of high-aligned carbon nanotubes deposited at room temperature. For this, we used the High Density Plasma Chemical Vapor Deposition system. This system uses a new concept of plasma generation: a planar coil is coupled to an RF system for plasma generation. This was used together with an electrostatic shield, for plasma densification, thereby obtaining high-density plasmas. The carbon nanotubes were deposited using pure methane plasmas. Three methods were used for the surface modification of the sample: reference substrate (silicon wafer only submitted to a chemical cleaning), silicon wafer with surface roughness generated by plasma etching, silicon wafer with a thin iron film and silicon wafer with diamond nano powder used as precursor materials. For each kind of silicon wafer surface, the carbon nanotubes were deposited with two different deposition times (two and three hours). The carbon nanotubes structural characteristics were analyzed by Atomic Force Microscope and Scanning Electronic Microscope. The carbon nanotubes electrical characteristics were observed by Raman Spectroscopy and the carbon nanotubes electro-optical properties were analyzed by current vs voltage electrical measurements and photo-luminescence spectroscopy measurements. The photoelectric effect in the carbon nanotubes were determined by photo-induced current measurements. In this work, we obtained carbon nanotubes with semiconductor properties and carbon nanotubes with metallic properties. The electro-optical effects depend strongly on the substrate preparation and the deposition parameters of the carbon nanotubes. The carbon nanotubes are high aligned and show singular properties that can be used for many applications.

Preparation and Microstructural,Structural,Optical and Electro-Optical Properties of La Doped Pmn-Pt Transparent Ceramics

Transparent relaxor ferroelectric ceramics of the system lanthanum modified lead magnesium niobate have been investigated for a variety of electro-optic properties could make these materials alternatives to (Pb,La)(Zr,Ti)O3. However, a study that relates the properties in function stoichiometric formula, it has not been analyzed heretofore. Therefore, in this work the effect of A-site substitution of La+3 in the characterization microstructural, structural, optical and electro-optical on (1-x)[Pb(1-3/2y)Lay(Mg1/3Nb2/3)O3]-xPbTiO3 and (1-z)[(1-x)Pb(Mg1/3Nb2/3)O3+xPbTiO3]+zLa2O3 has been performed. It was observed that the properties according to the stoichiometric formula and the PT had a maximum whose behavior was related to the addition of lanthanum in each stoichiometries.

Facet-dependent electro-optical properties of cholesteric liquid crystals doped with Cu2O nanocrystals

Excellent electro-optical （E-O） performances are essential for high-quality reflective cholesteric liquid crystal （LC） displays, but are often limited by the high driving voltages required by these displays. Dispersing functional nanomaterials into the LCs has emerged as a promising approach to achieve outstanding E-O properties. In this work, we report the facet-controlled E-O properties of a chiral nematic LC （N＊LC） doped with cubic, octahedral, and rhornbic dodecahedral Cu20. The outstanding E-O properties of the doped systems are related to the interaction between the liquid crystals and Cu20 dopants with different exposed crystal planes. Doping with octahedral and rhombic dodecahedral Cu20 reduces the stability of the planar state, as a result of both the surface abundance of active Cu atoms that interact with the polarized LC molecules, and the large amounts of vertexes and edges on the crystal surfaces, which accelerate the transition from the planar to the focal conic state under an applied electric field. Rhombic Cu20 is the most effective dopant for improving the E-O properties of the present LCs, resulting in a 65.31% reduction of the threshold voltage. The facet and morphology effects highlighted in this work provide a new pathway to develop excellent energy-saving meso-materials with exposed high-reactivity facets, improving their potential applications in electro-optical technologies and information displays.

A novel coupled quantum well structure and its excellent electro-optical properties

A novel InGaAs/InAlAs coupled quantum well structure is proposed for large field-induced refractive index change with low absorption loss. In the case of low applied electric field of 15 kV/cm and low absorption loss （α≤100 cm^-1）, a large field-induced refractive index change （for transverse electric （TE） mode, △n= 0.012; for transverse magnetic （TM） mode, △n = 0.0126） is obtained in the structure at the operation wavelength of 1.55 μm. The value is larger by over one order of magnitude than that in a rectangular quantum well. The result is very attractive for semiconductor optical switching devices.

Molecular simulation study of the microstructures and properties of pyridinium ionic liquid[HPy][BF_(4)]mixed with acetonitrile

The microstructures and thermodynamic properties of mixed systems comprising pyridinium ionic liquid[HPy][BF_(4)]and acetonitrile at different mole fractions were studied using molecular dynamics simulation in this work.The following properties were determined:density,self-diffusion coefficient,excess molar volume,and radial distribution function.The results show that with an increase in the mole fraction of[HPy][BF_(4)],the self-diffusion coefficient decreases.Additionally,the excess molar volume initially decreases,reaches a minimum,and then increases.The rules of radial distribution functions(RDFs)of characteristic atoms are different.With increasing the mole fraction of[HPy][BF_(4)],the first peak of the RDFs of HA1-F decreases,while that of CT6-CT6 rises at first and then decreases.This indicates that the solvent molecules affect the polar and non-polar regions of[HPy][BF_(4)]differently.

An investigation on a novel PDLC film's fabrication and its electro-optical properties

A polymer dispersed liquid crystal (PDLC) film that has good electro-optical properties is produced by the method of polymerized-induced phase separation. Based on the application foreground, its capability parameters, such as contrast ratio, work voltage, and visual angle, are characterized for the first time by a white light but not a fixed wavelength light. The results show the PDLC film has a low work-voltage of 20 V, more than 150° visual angle, high stability, and long lifetime. The differences between plastic and glass ITO-coated substrates of PDLC films are also studied in this paper. The plastic substrate has better property and will have a wider perspective especially in the portable, tender and folded display devices. Due to adjustable properties of film by electric field, PDLC has the potential application for display device, sensor, switch, grating, and new generation analytical apparatus.

Synthesis and electro-optic properties of fluorine-containing polyimide

The fluorine-containing organic polymer was synthesized from 3, 3＇, 4, 4＇-Bisphenyltetracarboxylic （BPDA）, and 2,2-Bis （3-amino-4-hydroxyyphenyl） hexafluoropropane （6FHP）. It is a first-step preparation of a preimided hydroxy-containing polyimide, followed by the covalent bonding of an active chromophore, dispersed red 19 （DR19）, onto the backbone of the polyimide via the Mitsunobu reaction. The nonlinear optical （NLO） containing polyimide was synthesized. The differential scanning calorimeter （DSC）and thermal gravimetric analysis （TGA） exhibited Tg and the temperature Tg at which 5 % mass losses occurring of polymer were 248 and 309 ℃, respectively. A reflective electro-optic （EO） modulator using this polymer was fabricated. The optical nonlinearities were determined to be d33 = 5. 209×10^-9 esu （poling voltage of 3.6 kV, 205 ℃） and d33 =7. 418×10^-9esu （poling voltage of 3. 8 kV, 210 ℃） by the second harmonic generation method in in-situ condition at a fundamental wavelength of 1 064 nm. The EO coefficients 733 of the polymer layer in the EO modulator were determined to be 2. 182 pm/V （poling voltage of 3.6 kV, 205 ℃） and 3. 107 pm/V （poling voltage of 3.8 kV, 210 ℃） at 1064 nm by an attenuated-total-reflection （ATR） method.

Properties of DR1/PMMA-co-GMA for High Speed Electro-optical Switch

A non-linear optical（NLO） material was synthesized by means of a simple method.This material can be applied in electro-optical（EO） devices,such as EO switches and modulators.The Disperse Red 1（DR1） was doped in polymethyl-methacrylate-co-glycidyl methacrylate（PMMA-co-GMA） as the NLO active chromophore.The synthesis process and material structure were expressed.The thermal properties,surface morphology and optical characteristics of the material were investigated by means of differential scanning calorimetry（DSC）,thermogravimetric analysis（TGA）,atomic force microscopy（AFM）,and m-lines technique.Using the reflection technique,the value of the electro-optical coefficient γ 33 was measured as 11 pm/V at a wavelength of 1310 nm.An EO switch with nanosecond response based on this material has been fabricated.

Electro-optical Properties of Liquid Crystal Composite Materials

The liquid crystal composite materials consist of microdroplets of liquid crystals which are spontaneously formed in a matrix of a polymer at the time of its polymerization. The director configuration in liquid crystal droplets, the model of orientation of droplets, and the contrast ratios of a cell are investigated. Droplet size, spacing and distribution are readily controlled in these materials to allow optimization of displays based upon electrically controlled light scattering from the liquid crystal droplets. Preliminary experimental and theoretical studies of the light scattering and electro-optic response of new material show that these materials can offer new features suitable for large area displays and light valves.

Effect of polymer structures on electro-optical properties of polymer stabilized liquid crystal films

The polymer stabilized liquid crystal(PSLC)film is a relatively novel electro-optical material,which is generally obtained by dissolving a small amount of a bifunctional photoreactive monomer in a low molecular mass liquid crystal.In this paper,the PSLC films were prepared with photoreactive biphenyl methacrylate monomers by photopolymerization induced phase separation.The effects of liquid crystal concentration,curing time,monomer structures and alignment layer on the electro-optical properties of PSLC films were investigated.The results show that the transmittance in the OFF state(TOFF)increased with the liquid crystal concentration,but the driving voltage decreased.TOFF was also influenced by the curing time.Furthermore,when polyimide was used as alignment layer,the films prepared from the bifunctional monomer shows a higher TOFF,while those from the single functional monomer exhibited a deformed electro-optical curve due to the unsteady polymer networks.

Properties and Characteristics of Regolith-Based Materials for Extraterrestrial Construction

The construction of extraterrestrial bases has become a new goal in the active exploration of deep space.Among the construction techniques,in situ resource-based construction is one of the most promising because of its good sustainability and acceptable economic cost,triggering the development of various types of extraterrestrial construction materials.A comprehensive survey and comparison of materials from the perspective of performance was conducted to provide suggestions for material selection and optimization.Thirteen types of typical construction materials are discussed in terms of their reliability and applicability in extreme extraterrestrial environment.Mechanical,thermal and optical,and radiation-shielding properties are considered.The influencing factors and optimization methods for these properties are analyzed.From the perspective of material properties,the existing challenges lie in the comprehensive,long-term,and real characterization of regolith-based construction materials.Correspondingly,the suggested future directions include the application of high-throughput characterization methods,accelerated durability tests,and conducting extraterrestrial experiments.

Physical,mechanical and thermal properties of vacuum sintered HUST-1 lunar regolith simulant

Establishing a base on the Moon is one of the new goals of human lunar exploration in recent years.Sintered lunar regolith is one of the most potential building materials for lunar bases.The physical,mechanical and thermal properties of sintered lunar regolith are vital performance indices for the structural design of a lunar base and analysis of many critical mechanical and thermal issues.In this study,the HUST-1 lunar regolith simulant(HLRS)was sintered at 1030,1040,1050,1060,1070,and 1080℃.The effect of sintering temperature on the compressive strength was investigated,and the exact value of the optimum vacuum sintering temperature was determined between 1040 and 1060℃.Then,the microstructure and material composition of vacuum sintered HLRS at different temperatures were characterized.It was found that the sintering temperature has no significant effect on the mineral composition in the temperature range of 1030-1080℃.Besides,the heat capacity,thermal conductivity,and coefficient of thermal expansion(CTE)of vacuum sintered HLRS at different temperatures were investigated.Specific heat capacity of sintered samples increases with the increase of test temperature within the temperature range from-75 to 145℃.Besides,the thermal conductivity of the sintered sample is proportional to density.Finally,the two temperatures of 1040 and 1050℃were selected for a more detailed study of mechanical properties.The results showed that compressive strength of sintered sample is much higher than tensile strength.This study reveals the effects of sintering temperature on the physical,mechanical and thermal properties of vacuum sintered HLRS,and these material parameters will provide support for the construction of future lunar bases.

High-throughput calculations combining machine learning to investigate the corrosion properties of binary Mg alloys

Magnesium(Mg)alloys have shown great prospects as both structural and biomedical materials,while poor corrosion resistance limits their further application.In this work,to avoid the time-consuming and laborious experiment trial,a high-throughput computational strategy based on first-principles calculations is designed for screening corrosion-resistant binary Mg alloy with intermetallics,from both the thermodynamic and kinetic perspectives.The stable binary Mg intermetallics with low equilibrium potential difference with respect to the Mg matrix are firstly identified.Then,the hydrogen adsorption energies on the surfaces of these Mg intermetallics are calculated,and the corrosion exchange current density is further calculated by a hydrogen evolution reaction(HER)kinetic model.Several intermetallics,e.g.Y_(3)Mg,Y_(2)Mg and La_(5)Mg,are identified to be promising intermetallics which might effectively hinder the cathodic HER.Furthermore,machine learning(ML)models are developed to predict Mg intermetallics with proper hydrogen adsorption energy employing work function(W_(f))and weighted first ionization energy(WFIE).The generalization of the ML models is tested on five new binary Mg intermetallics with the average root mean square error(RMSE)of 0.11 eV.This study not only predicts some promising binary Mg intermetallics which may suppress the galvanic corrosion,but also provides a high-throughput screening strategy and ML models for the design of corrosion-resistant alloy,which can be extended to ternary Mg alloys or other alloy systems.

A review on the multi-scaled structures and mechanical/thermal properties of tool steels fabricated by laser powder bed fusion additive manufacturing

The laser powder bed fusion(LPBF) process can integrally form geometrically complex and high-performance metallic parts that have attracted much interest,especially in the molds industry.The appearance of the LPBF makes it possible to design and produce complex conformal cooling channel systems in molds.Thus,LPBF-processed tool steels have attracted more and more attention.The complex thermal history in the LPBF process makes the microstructural characteristics and properties different from those of conventional manufactured tool steels.This paper provides an overview of LPBF-processed tool steels by describing the physical phenomena,the microstructural characteristics,and the mechanical/thermal properties,including tensile properties,wear resistance,and thermal properties.The microstructural characteristics are presented through a multiscale perspective,ranging from densification,meso-structure,microstructure,substructure in grains,to nanoprecipitates.Finally,a summary of tool steels and their challenges and outlooks are introduced.

Tetrahedral framework nucleic acids/hyaluronic acidmethacrylic anhydride hybrid hydrogel with antimicrobial and anti-inflammatory properties for infected wound healing

Bacterial resistance and excessive inflammation are common issues that hinder wound healing.Antimicrobial peptides(AMPs)offer a promising and versatile antibacterial option compared to traditional antibiotics,with additional anti-inflammatory properties.However,the applications of AMPs are limited by their antimicrobial effects and stability against bacterial degradation.TFNAs are regarded as a promising drug delivery platform that could enhance the antibacterial properties and stability of nanodrugs.Therefore,in this study,a composite hydrogel(HAMA/t-GL13K)was prepared via the photocross-linking method,in which tFNAs carry GL13K.The hydrogel was injectable,biocompatible,and could be instantly photocured.It exhibited broad-spectrum antibacterial and anti-inflammatory properties by inhibiting the expression of inflammatory factors and scavenging ROS.Thereby,the hydrogel inhibited bacterial infection,shortened the wound healing time of skin defects in infected skin full-thickness defect wound models and reduced scarring.The constructed HAMA/tFNA-AMPs hydrogels exhibit the potential for clinical use in treating microbial infections and promoting wound healing.

Effects of deformation temperatures on microstructures,aging behaviors and mechanical properties of Mg-Gd-Er-Zr alloys fabricated by hard-plate rolling

In this investigation,a high-strength Mg-12Gd-1.0Er-0.5Zr(wt.%)alloy sheet was produced by hot extrusion(HE)and subsequent hard-plate rolling(HPR)at different temperatures.The results indicate that the microstructures of these final-rolled sheets are inhomogeneous,mainly including coarse deformed grains and dynamic recrystallized(DRXed)grains,and the volume fraction of these coarse deformed grains increases as the rolling temperature increases.Thus,more DRXed grains can be found in R-385℃sheet,resulting in a smaller average grain size and weaker basal texture,while the biggest grains and the highest strong basal texture are present in R-450℃sheet.Amounts of dynamic precipitation ofβphases which are mainly determined by the rolling temperature are present in these sheets,and its precipitation can consume the content of Gd solutes in the matrix.As a result,the lowest number density ofβphase in R-450℃sheet is beneficial to modify the age hardening response.Thus,the R-450℃sheet displays the best age hardening response because of a severe traditional precipitation ofβ’(more)andβH/βM(less)precipitates,resulting in a sharp improvement in strength,i.e.ultimate tensile strength(UTS)of∼518±17 MPa and yield strength(YS)of∼438±18 MPa.However,the elongation(EL)of this sheet reduces greatly,and its value is∼2.7±0.3%.By contrasting,the EL of the peak-aging R-385℃sheet keeps better,changing from∼4.9±1.2%to∼4.8±1.4%due to a novel dislocation-induced chain-like precipitate which is helpful to keep good balance between strength and ductility.

Machine learning applications on lunar meteorite minerals:From classification to mechanical properties prediction

Amid the scarcity of lunar meteorites and the imperative to preserve their scientific value,nondestructive testing methods are essential.This translates into the application of microscale rock mechanics experiments and scanning electron microscopy for surface composition analysis.This study explores the application of Machine Learning algorithms in predicting the mineralogical and mechanical properties of DHOFAR 1084,JAH 838,and NWA 11444 lunar meteorites based solely on their atomic percentage compositions.Leveraging a prior-data fitted network model,we achieved near-perfect classification scores for meteorites,mineral groups,and individual minerals.The regressor models,notably the KNeighbor model,provided an outstanding estimate of the mechanical properties—previously measured by nanoindentation tests—such as hardness,reduced Young’s modulus,and elastic recovery.Further considerations on the nature and physical properties of the minerals forming these meteorites,including porosity,crystal orientation,or shock degree,are essential for refining predictions.Our findings underscore the potential of Machine Learning in enhancing mineral identification and mechanical property estimation in lunar exploration,which pave the way for new advancements and quick assessments in extraterrestrial mineral mining,processing,and research.