A dual-RPA based lateral flow strip for sensitive,on-site detection of CP4-EPSPS and Cry1Ab/Ac genes in genetically modified crops

Traditional transgenic detection methods require high test conditions and struggle to be both sensitive and efficient.In this study,a one-tube dual recombinase polymerase amplification(RPA)reaction system for CP4-EPSPS and Cry1Ab/Ac was proposed and combined with a lateral flow immunochromatographic assay,named“Dual-RPA-LFD”,to visualize the dual detection of genetically modified(GM)crops.In which,the herbicide tolerance gene CP4-EPSPS and the insect resistance gene Cry1Ab/Ac were selected as targets taking into account the current status of the most widespread application of insect resistance and herbicide tolerance traits and their stacked traits.Gradient diluted plasmids,transgenic standards,and actual samples were used as templates to conduct sensitivity,specificity,and practicality assays,respectively.The constructed method achieved the visual detection of plasmid at levels as low as 100 copies,demonstrating its high sensitivity.In addition,good applicability to transgenic samples was observed,with no cross-interference between two test lines and no influence from other genes.In conclusion,this strategy achieved the expected purpose of simultaneous detection of the two popular targets in GM crops within 20 min at 37°C in a rapid,equipmentfree field manner,providing a new alternative for rapid screening for transgenic assays in the field.

Recent progress on nanomaterial-based electrochemical dissolved oxygen sensors

Dissolved oxygen(DO)usually refers to the amount of oxygen dissolved in water.In the environment,medicine,and fermentation industries,the DO level needs to be accurate and capable of online monitoring to guide the precise control of water quality,clinical treatment,and microbial metabolism.Compared with other analytical methods,the electrochemical strategy is superior in its fast response,low cost,high sensitivity,and portable device.However,an electrochemical DO sensor faces a trade-off between sensitivity and long-term stability,which strongly limits its practical applications.To solve this problem,various advanced nanomaterials have been proposed to promote detection performance owing to their excellent electrocatalysis,conductivity,and chemical stability.Therefore,in this review,we focus on the recent progress of advanced nanomaterial-based electrochemical DO sensors.Through the comparison of the working principles on the main analysis techniques toward DO,the advantages of the electrochemical method are discussed.Emphasis is placed on recently developed nanomaterials that exhibit special characteristics,including nanostructures and preparation routes,to benefit DO determination.Specifically,we also introduce some interesting research on the configuration design of the electrode and device,which is rarely introduced.Then,the different requirements of the electrochemical DO sensors in different application fields are included to provide brief guidance on the selection of appropriate nanomaterials.Finally,the main challenges are evaluated to propose future development prospects and detection strategies for nanomaterial-based electrochemical sensors.

Heterogeneous Cu_(x)O Nano‑Skeletons from Waste Electronics for Enhanced Glucose Detection

Electronic waste(e-waste)and diabetes are global challenges to modern societies.However,solving these two challenges together has been challenging until now.Herein,we propose a laser-induced transfer method to fabricate portable glucose sensors by recycling copper from e-waste.We bring up a laser-induced full-automatic fabrication method for synthesizing continuous heterogeneous Cu_(x)O(h-Cu_(x)O)nano-skeletons electrode for glucose sensing,offering rapid(<1 min),clean,air-compatible,and continuous fabrication,applicable to a wide range of Cu-containing substrates.Leveraging this approach,h-Cu_(x)O nanoskeletons,with an inner core predominantly composed of Cu_(2)O with lower oxygen content,juxtaposed with an outer layer rich in amorphous Cu_(x)O(a-Cu_(x)O)with higher oxygen content,are derived from discarded printed circuit boards.When employed in glucose detection,the h-Cu_(x)O nano-skeletons undergo a structural evolution process,transitioning into rigid Cu_(2)O@CuO nano-skeletons prompted by electrochemical activation.This transformation yields exceptional glucose-sensing performance(sensitivity:9.893 mA mM^(-1) cm^(-2);detection limit:0.34μM),outperforming most previously reported glucose sensors.Density functional theory analysis elucidates that the heterogeneous structure facilitates gluconolactone desorption.This glucose detection device has also been downsized to optimize its scalability and portability for convenient integration into people’s everyday lives.

A Glassy Carbon Electrode Modified with Cellulose Nanofibrils from Ammophila arenaria for the Sensitive Detection of L-Trytophan

L-tryptophan is an essential amino acid for human health. Nanofibrillated cellulose (NFC) from marram grass (Ammophila arenaria) extracted from plants harvested in the center of Tunisia was used for the first time for the modification of a glassy carbon electrode (GCE), for the sensitive detection of L-tryptophan (Trp). After spectroscopic and morphological characterization of the extracted NFC, the GC electrode modification was monitored through cyclic voltammetry. The NFC-modified electrode exhibited good analytical performance in detecting Trp with a wide linear range between 7.5 × 10−4 mM and 10−2 mM, a detection limit of 0.2 µM, and a high sensitivity of 140.0 µA∙mM−1. Additionally, the NFC/GCE showed a good reproducibility, good selectivity versus other amino acids, uric acid, ascorbic acid, and good applicability to the detection of Trp in urine samples.

Electrochemically reduced graphene oxide with enhanced electrocatalytic activity toward tetracycline detection

An electrochemically reduced graphene oxide sample, ERGO_0.8v, was prepared by electrochemical reduction of graphene oxide （GO） at -0.8 V, which shows unique electrocatalytic activity toward tetracycline （TTC） detection compared to the ERGO-12v （GO applied to a negative potential of-1.2 V）, GO, chemically reduced GO （CRGO）-modified glassy carbon electrode （GC） and bare GC electrodes. The redox peaks of TTC on an ERGO-0.8v-modifled glass carbon electrode （GC/ERGO-0.8v） were within 0-0.5 V in a pH 3.0 buffer solution with the oxidation peak current correlating well with TTC concentration over a wide range from 0.1 to 160 mg/L Physical characterizations with Fourier transform infrared （FT-IR）, Raman, and X-ray photoelectron spectroscopies （XPS） demonstrated that the oxygen-containing functional groups on GO diminished after the electrochemical reduction at -0.8 V, yet still existed in large amounts, and the defect density changed as new sp2 domains were formed. These changes demonstrated that this adjustment in the number of oxygen-containing groups might be the main factor affecting the electrocatalytic behavior of ERGO. Additionally, the defect density and sp2 domains also exert a profound influence on this behavior. A possible mechanism for the TTC redox reaction at the GC/ERGO-0.8v electrode is also presented. This work suggests that the electrochemical reduction is an effective method to establish new catalytic activities of GO by setting appropriate parameters.

Determination of atmospheric hydroxyl radical by HPLC coupled with electrochemical detection

The hydroxyl radical （·OH） plays a central role in the oxidation and removal of many atmospheric compounds. Measurement of atmospheric ·OH is very difficult because of its high reactivity and low atmospheric abundance. In this article, a simple and highly sensitive method, high performance liquid chromatography coupled with coulometric detection （HPLC-CD）, was developed to determine ·OH indirectly by determining its reaction products with salicylic acid （SAL）, 2,3-dihydroxybenzoic acid （2,3-DHBA）, and 2,5-dihydroxybenzoic acid （2,5-DHBA）. Under the optimum conditions for its determination, 2,3-DHBA and 2,5-DHBA could be well separated and the detection limits for 2,3-DHBA were 3 ×10^-10 mol/L and for 2,5-DHBA were 1.5 ×10^-10 mol/L, which were lower than most previous reports. This method was also applied to measure atmospheric hydroxyl radical levels and demonstrated the feasibility in clean and polluted air.

Analysis of Amino Acids in a Single Human Red Blood Cell by Capillary Zone Electrophoresis with Intracellular NDA- derivatization and Electrochemical Detection

A novel method for determination of amino acids in individual human red blood cells has been developed. In this method, the derivatization reagents (NDA and CN-) are introduced into living cells by electroporation. After completion of derivatization, the amino acids in a single cell is determined by capillary zone electrophoresis with end-column amperometric detection.

A MXene-functionalized paper-based electrochemical immunosensor for label-free detection of cardiac troponin I

Convenient,rapid,and accurate detection of cardiac troponin I(cTnI)is crucial in early diagnosis of acute myocardial infarction(AMI).A paper-based electrochemical immunosensor is a promising choice in this field,because of the flexibility,porosity,and cost-efficacy of the paper.However,paper is poor in electronic conductivity and surface functionality.Herein,we report a paper-based electrochemical immunosensor for the label-free detection of cTnI with the working electrode modified by MXene(Ti_(3)C_(2))nanosheets.In order to immobilize the bio-receptor(anti-cTnI)on the MXene-modified working electrode,the MXene nanosheets were functionalized by aminosilane,and the functionalized MXene was immobilized onto the surface of the working electrode through Nafion.The large surface area of the MXene nanosheets facilitates the immobilization of antibodies,and the excellent conductivity facilitates the electron transfer between the electrochemical species and the underlying electrode surface.As a result,the paper-based immunosensor could detect cTnI within a wide range of 5-100 ng/mL with a detection limit of 0.58 ng/mL.The immunosensor also shows outstanding selectivity and good repeatability.Our MXene-modified paper-based electrochemical immunosensor enables fast and sensitive detection of cTnI,which may be used in real-time and cost-efficient monitoring of AMI diseases in clinics.

Separation and Determination of Methylnaltrexone in Human Plasma Samples After Oral Administration by HPLC Coupled with Electrochemical Detection

A high performance liquid chromatography(HPLC) method coupled with electrochemical detection and solid phase extraction is described for the separation and determination of methylnaltrexone(MNTX), a quaternary opioid antagonist, in human clinical plasma samples after oral administration. Linearity of the standard curve for MNTX was found in the range of 4.0_150 ng/mL and was statistically conformed. The correlation coefficient(r2) and calibration equation obtained from linear regression analysis are 0.9999 and Y=54.27X-0.22, where Y and X represent the peak area and concentration of MNTX, respectively. The detection limit of MNTX under the present experimental conditions is 2.0 ng/mL by estimating at a ratio of 3 of signal to noise. The mean recovery of MNTX in human plasma is higher than 97%. The analytical method was applied to the pharmacokinetic determination of MNTX after single dose oral administration. These data demonstrate that the change of MNTX plasma concentration versus time is obvious. MNTX level of plasma reaches to a plateau between 45 to 120 minutes and then falls slowly. The content of MNTX in plasma sample maintains at an obviously detectable level after twelve hours of oral administration. The pharmacokinetic parameters for a single dose of 19.2 mg/kg in plasma are c_~max =206.42(±16.53) ng/mL and t_~max =60 min.

Quality Analysis of Herbal Medicine Products Prepared from Herba Sarcandrae by Capillary Electrophoresis with Electrochemical Detection

A capillary electrophoresis with electrochemical detection（CE-ED） method was developed for the quality analysis of herbal medicine products prepared from the same herb of Herba Sarcandrae： Fufang Caoshanhu tablets, Qingrexiaoyanning capsules, and Xuekang oral liquids. Under the optimal analysis conditions, the low detection limit[l.0×10^-7 mol/L（S/N=3）] and the wide linear range（1.0×10^-7-1.0×10^-4 mol/L） were obtained for quality standard compound of isofraxidin. The precisions of the peak current and the migration time（as RSDs） for the real sample analysis were 2.0%-2.6%, and 1.2%-1.8% for isofraxidin, respectively. The contents of isofraxidin detected were 15.77 μg/tablet, 0.48 mg/capsule, 1.2 mg/ampoule（Jiangxi）, and 0.44 mg/ampoule（Dalian） for Fufang Caoshanhu tablets, Qingrexiaoyanning capsules, and Xuekang oral liquids from different manufacturers, respectively. Quality estimate was conducted by comparing the contents of isofraxidin in the herbal medicine products with the demanded values of Chinese pharmacopeia. In addition, based on their own unique CE-ED profiles（namely, CE-ED electropherograms） the Xuekang oral liquids from the different manufacturers could be easily identified.

Plasma Activation of Integrated Carbon Nanotube Electrodes for Electrochemical Detection of Catechol

In this study, integrated multi-wall carbon nanotube （MWCNT） electrodes were prepared in the holes of glass directly by microwave plasma chemical vapour deposition （MWPCVD）. The electrochemical behaviour of catechol at the integrated MWCNT electrodes was investigated. The oxygen plasma treated CNT electrodes had better electrochemical performance for the analysis of catechol than that of as-synthesized CNT electrodes. Both the as-synthesized CNTs and plasma treated CNTs were characterized by TEM（transmission electron microscopy, XPS（X-ray photoelectron spectroscopy） and Raman spectroscopy. The results revealed that the oxygen plasma activation is an effective method to enhance the electrochemical properties of CNT electrodes.

Electrochemical Detection of Sudan I Using a Multi-Walled Carbon Nanotube/Chitosan Composite Modified Glassy Carbon Electrode

In this work, a simple and sensitive electrochemical method was developed to determine Sudan I by cyclic voltammetry and differential pulse voltammetry using a glassy carbon electrode modified with a chitosan/carbon nanotube composite. In cyclic voltammetry, Sudan I exhibited a well-defined oxidation peak located at 0.72 V at the multi-walled carbon nanotube (MWCNT)/chitosan-modified GCE. The determination conditions, including pH, scan rate, and chitosan: MWCNT mass ratio at the modified electrode, were optimized. Under the optimum experimental conditions, Sudan I could be linearly detected by differential pulse voltammetry with a detection limit of 3.0 × 10-8 mol?L-1.

Determination of Nicotine in Tobacco by Capillary Electrophoresis with Electrochemical Detection

A sensitive, simple and low-cost method based on capillary electrophoresis（CE） with electrochemical（EC） detection at a carbon fiber microdisk electrode（CFE） was developed for the determination of nicotine. Effects of de- tection potential, concentration and pH value of the phosphate buffer, and injection time as well as separation voltage were investigated. Under the optimized conditions： a detection potential of 1.20 V, 40 rnmol/L phosphate buffer（pH 2.0）, a sample injection time of 10 s at 10 kV and a separation voltage of 16 kV, the linear range obtained was from 5.0×10^-7 mol/L to 1.0×10^-4 mol/L with a correlation coefficient of 0.9989 and the limit of detection（LOD, S/N=3） obtained was 5.0×10^-8 mol/L. The method was also used to determine the nicotine in cigarettes. Nicotine amount ranged from 0.211 mg/g to 0.583 mg/g in the pipe tobacco of seven brands of cigarette and the amount in one ciga- rette varied from 0.136 mg/cigarette to 0.428 mg/cigarette.

Recent Advance in the Electrochemical Detection of Sulphide and Sulphhydryl Species

This article aims at providing a critical review of some most recent developments in the electrochemical detection and measurement of hydrogen sulphide and the related species, which are of great significance to a variety of industries and in environmental moitoring. The molecular recognition processes are initiated by using either an organic precursor or a catalytic complex, leading to extensive ranges of detection. A series of advanced chemical and simulation techniques are used to probe the mechanistic details of the analytical chemistry involved.

Assay of Histamine in Single Mast Cells by Capillary Zone Electrophoresis with Electrochemical Detection

Capillary zone electrophoresis was employed for the analysis of histamine in single rat peritoneal mast cells using an amperometric detector. In this method, individual mast cells and then 0.02 mol/L NaOH as a lysing solution are injected into the front end of the separation capillary. A cell injector was constructed for easy injection of single cells. Histamine in single mast cells has been identified and quantified.

Electrochemical Detection of Alkaline Phosphatase in BALB/c Mouse Fetal Liver Stromal Cells with Capillary Electrophoresis

A method for determination of alkaline phosphatase (ALP) in BALB/c mouse fetal liver stromal cells has been described based on the catalytic reaction. After the cell extract is incubated with the substrate disodium phenyl phosphate, the reaction product phenol generated by ALP is determined by capillary electrophoresis with electrochemical detection.

Rapid Determination of Dopamine and Its Metabolites During in vivo Cerebral Microdialysis by Routine High Performance Liquid Chromatography With Electrochemical Detection

To determine dopamine and its metabolites during in vivo cerebral microdialysis by routine high performance liquid chromatography with electrochemical detection. Methods Microdialysis probes were placed into the right striatum of Wistar rat brains and perfused with Ringer＇s solution at a rate of 1.5 pL/min. A reverse phase HPLC with electrochemistry was used to assay DA, DOPAC, and HVA after cerebral microdialysates were collected every 20 minutes from awake and freely moving rats. In order to identify the reliability of this method, its selectivity, linear range, precision and accuracy were tested and the contents of DA, DOPAC, and HVA in rat microdialysates were determined. Results The standard curve was in good linear at the concentration ranging from 74 nmol/L to 1.5 pmol/L for DOPAC （r^2= 0.9996）, from 66 nmol/L to 1.3 gmol/L for DA （r^2=l.0000） and from 69 nmol/L to 1.4 pmol/L for HVA （r^2=0.9992）. The recovery of DOPAC （0.30, 0.77, 1.49 gmol/L）, DA （0,26, 0.69, 1.32 gmol/L）, and HVA （0.27, 0.71, 1.37 gmol/L） was 82.00±1.70%, 104.00±4.00%, 98.70±3.10%; 92.30± 1.50%, 105.30±2.30%, 108.00±2.00%; 80.00±7.80%, 107.69±8.00%, and 108.66±3.10%, respectively at each concentration. Their intra-day RSD was 3.3%, 3.4%, and 2.5%, and inter-day RSD was 4.2%, 2.3%, and 5.6%, respectively. The mean extracellular concentrations of DOPAC, DA, and HVA in rat brain microdialysates were 10.7, 2.4, and 9.2 gmol/L （n=6）, respectively. Conclusion The findings of our study suggested that the simple, accurate and stable method can be applied to basic researches of diseases related to monoamines neurotransmitters by cerebral microdialysis in rats.

Extraordinary tunable dynamic range of electrochemical aptasensor for accurate detection of ochratoxin A in food samples

We report the design of a sensitive,electrochemical aptasensor for detection of ochratoxin A(OTA)with an extraordinary tunable dynamic sensing range.This electrochemical aptasensor is constructed based on the target induced aptamer-folding detection mechanism and the recognition between OTA and its aptamers results in the conformational change of the aptamer probe and thus signal changes for measurement.The dynamic sensing range of the electrochemical aptasensor is successfully tuned by introduction of free assistant aptamer probes in the sensing system.Our electrochemical aptasensor shows an extraordinary dynamic sensing range of 11-order magnitude of OTA concentration from 10^−8 to 10^2 ng/g.Of great significance,the signal response in all OTA concentration ranges is at the same current scale,demonstrating that our sensing protocol in this research could be applied for accurate detections of OTA in a broad range without using any complicated treatment of signal amplification.Finally,OTA spiked red wine and maize samples in different dynamic sensing ranges are determined with the electrochemical aptasensor under optimized sensing conditions.This tuning strategy of dynamic sensing range may offer a promising platform for electrochemical aptasensor optimizations in practical applications.

Determination of Amino Acids in Single Human Lymphocytes after On-capillary Derivatization by Capillary Zone Electrophoresis with Electrochemical Detection

Amino acids in individual human lymphocytes were determined by capillary zone electrophoresis with electrochemical detection after on-capillary derivatization. In order to inject cells easily, a cell injector was designed. Four amino acids (serine, alanine, taurine, and glycine) in single human lymphocytes have been identified. Quantitation has been accomplished through the use of calibration curves.

Analysis of Ascorbic Acid in Single Human Neutrophils by Electrochemical Detection

Ascorbic acid in individual human neutrophils was determined by capillary zoneelectrophoresis with electrochemical detection. In order to overcome the influence of theadsorption of the substances in cells on the inner surface wall of the capillary on the migration time and the number of theoretical plates, a procedure for treating capillaries has been described.