Biodiesel fuel is a potential alternative energy source for diesel engines due to its physiochemical characteristics relatively similar to those of traditional diesel fuel.In this study,the performance,emission,and co...Biodiesel fuel is a potential alternative energy source for diesel engines due to its physiochemical characteristics relatively similar to those of traditional diesel fuel.In this study,the performance,emission,and combustion features of a mono cylinder DI diesel engine are assessed using 20%Pumpkin seed methyl ester(PSOME20)and considering varying injection pressures(200,220,240,and 260 bar).The considered Pumpkin seed oil is converted into pumpkin biodiesel by transesterification and then used as fuel.The findings demonstrate that the Brake Thermal Efficiency(BTE)of PSOME20 can be raised by 1.68%,and the carbon monoxide(CO),hydrocarbon(HC),and smoke emanations can be lowered,while oxides of nitrogen(NOx)emissions are increased at an injection pressure(IP)of 240 bar compared to the standard IP of 200 bar.The cylinder pressure and the Heat Release Rate(HRR)become higher at 240 bar,whereas the ignition delay is shortened with respect to PSOME20 at a normal IP of 200 bar.展开更多
A thermoelectric generation Stirling engine (TEG-Stirling engine) is discussed by employing a low temperature Stirling engine and the dissipative equation of motion derived from the method of thermomechanical dynamics...A thermoelectric generation Stirling engine (TEG-Stirling engine) is discussed by employing a low temperature Stirling engine and the dissipative equation of motion derived from the method of thermomechanical dynamics (TMD). The results and mechanism of axial flux electromagnetic induction (AF-EMI) are applied to a low temperature Stirling engine, resulting in a TEG-Stirling engine. The method of TMD produced thermodynamically consistent and time-dependent physical quantities for the first time, such as internal energy ℰ(t), thermodynamic work Wth(t), the total entropy (heat dissipation) Qd(t)and measure or temperature of a nonequilibrium state T˜(t). The TMD analysis produced a lightweight mechanical system of TEG-Stirling engine which derives electric power from waste heat of temperature (40˚CT100˚C) by a thermoelectric conversion method. An optimal low rotational speed about 30θ′(t)/(2π)60(rpm) is found, applicable to devices for sustainable, clean energy technologies. The stability of a thermal state and angular rotations of TEG-Stirling engine are specifically shown by employing properties of nonequilibrium temperature T˜(t), which is also applied to study optimal fuel-injection and combustion timings of heat engines.展开更多
Combustion noise takes large proportion in diesel engine noise and the studies of its influence factors play an important role in noise reduction. Engine noise and cylinder pressure measurement experiments were carrie...Combustion noise takes large proportion in diesel engine noise and the studies of its influence factors play an important role in noise reduction. Engine noise and cylinder pressure measurement experiments were carried out. And the improved attenuation curves were obtained, by which the engine noise was predicted. The effect of fuel injection parameters in combustion noise was investigated during the combustion process. At last, the method combining single variable optimization and multivariate combination was introduced to online optimize the combustion noise. The results show that injection parameters can affect the cylinder pressure rise rate and heat release rate, and consequently affect the cylinder pressure load and pressure oscillation to influence the combustion noise. Among these parameters, main injection advance angle has the greatest influence on the combustion noise, while the pilot injection interval time takes the second place, and the pilot injection quantity is of minimal impact. After the optimal design of the combustion noise, the average sound pressure level of the engine is distinctly reduced by 1.0 d B(A) generally. Meanwhile, the power, emission and economy performances are ensured.展开更多
Experiments are conducted to develop an understanding of how split injections can affect the combustion and emission characteristics of a D.I. diesel engine with a common-rail injection system. The ratio of the amount...Experiments are conducted to develop an understanding of how split injections can affect the combustion and emission characteristics of a D.I. diesel engine with a common-rail injection system. The ratio of the amount of fuel injected between two injection pulses and the injection interval is varied keeping the injected fuel quantity constant. Results show that under the 70D90-10 injection pattern, the engine achieves the lower NOx-smoke emissions and BSFC compared with the single injection pattern. The heat release rate and the temperature show that the split injections increase the initial premixed burn and retards the diffusion burn. With the balance of these two effects, the maximum in-cylinder temperature decreases while the 50% heat release point is held at almost the same crank angle. Therefore, both NOx emission and BSFC are improved while keeping the smoke emission at the same level.展开更多
In order to effectively implement DPF(Diesel Particulate Filters)regeneration control,thermal management of exhaust products before and inside Diesel Oxidation Catalyst(DOC)is necessary.In the present study,the Influe...In order to effectively implement DPF(Diesel Particulate Filters)regeneration control,thermal management of exhaust products before and inside Diesel Oxidation Catalyst(DOC)is necessary.In the present study,the Influence of the intake throttle valve and late post injection process on temperature rise inside DOC is analyzed through engine bench tests.The steady experiment results show that adjustment of the intake throttle valve can effectively increase exhaust temperature before DOC;in particular,with intake throttle valve opening at 20%,temperature before DOC can be increased by about 170℃ with respect to the full opening.An increase in the late post injection quantity can produce a significant rise of the temperature inside DOC,however its impact on the exhaust temperature before DOC is relatively limited.As the late post injection quantity increases,Hydrocarbon(HC)emissions also grow;in the present work it is shown that with a proper injection quantity,a considerable temperature increase inside the DOC can be obtained with relatively low HC emission.More specifically,with the intake throttle valve at 30%and DOC reaching ignition temperature as the late post injection quantity is increased,the exhaust temperature after DOC can be made larger than 550℃,adequate for DPF active regeneration.展开更多
A simulation model of an electronically controlled two solenoid valve fuel injection system for a diesel engine is established in the AMESim environment.The accuracy of the model is validated through comparison with e...A simulation model of an electronically controlled two solenoid valve fuel injection system for a diesel engine is established in the AMESim environment.The accuracy of the model is validated through comparison with experimental data.The influence of pre-injection control parameters on main-injection quantity under different control modes is analyzed.In the spill control valve mode,main-injection fuel quantity decreases gradually and then reaches a stable level because of the increase in multi-injection dwell time.In the needle control valve mode,main-injection fuel quantity increases with rising multi-injection dwell time;this effect becomes more obvious at high-speed revolutions and large main-injection pulse widths.Pre-injection pulse width has no obvious influence on main-injection quantity under the two control modes;the variation in main-injection quantity is in the range of 1 mm3.展开更多
A direct injection low compression ratios diesel rotary engine is designed and studied to find the appropriate application of the electronic controlled high pressure common rail injection system. Current development f...A direct injection low compression ratios diesel rotary engine is designed and studied to find the appropriate application of the electronic controlled high pressure common rail injection system. Current development focuses on the applied fuel injection and ignition strategies, especially concerning the combustion configurations of injectors, ignition source, and combustion chamber. The prototype engine, equipped with Bosch common rail system and high performance electronic control unit (ECU), is designed correspondingly. Studies show that the integration of a common rail injection system and the main and pilot duel injectors configurations, assisted with glow plug ignition device and flexible ECU, represents a promising approach to improve the potential of the low compression ratios diesel rotary engine. Currently the engine can run at 6 kr · min^-1 steadily and the power is about 68 kW/(4 kr ·min^- 1).展开更多
This study investigated the relationship between a subject’s evaluation of injection molding machines (IMMs) and formal design features using Kansei engineering. This investigation used 12 word pairs to evaluate the ...This study investigated the relationship between a subject’s evaluation of injection molding machines (IMMs) and formal design features using Kansei engineering. This investigation used 12 word pairs to evaluate the IMM configurations and employed the semantic differential method to explore the perception of 60 interviewees of 12 examples. The relationship between product feature design and corresponding words was derived by multiple regression analysis. Factor analysis reveals that the 12 examples can be categorized as two styles—advanced style and succinct style. For the advanced style, an IMM should use a rectangular form for the clamping-unit cover and a full-cover for the injection-unit. For the succinct style, the IMM configuration should use a beveled form for the safety cover and a vertical rectangular form for the clamping-unit cover. Quantitative data and suggested guidelines for the relationship between design features and interviewee evaluations are useful to product designers when formulating design strategies.展开更多
The effects of various split injection strategies on the opposed-piston opposed-cylinder(OPOC)diesel engine combustion and emission characteristics have been studied numerically using AVL-Fire CFD tools.The five rate-...The effects of various split injection strategies on the opposed-piston opposed-cylinder(OPOC)diesel engine combustion and emission characteristics have been studied numerically using AVL-Fire CFD tools.The five rate-shaped main injections were used in split injection strategies.The results show that ignition delay from a rectangular injection rate is the shortest.Maximum pressure of the trapezoid injection rate is the largest.And the NOx emission of the rectangular injection rate is the largest.Meanwhile,the soot emission of the trapezoid injection rate is the least among the five injection rates.展开更多
Presents the conception of concurrent engineering employed for CAD/CAM of injection moulds by closely combining the management science with the manufacturing techniques with the cost of processing, material cost, etc ...Presents the conception of concurrent engineering employed for CAD/CAM of injection moulds by closely combining the management science with the manufacturing techniques with the cost of processing, material cost, etc taken into consideration from the conceptural design to delivery of products and concludes with the results of analyses that the cost of finished plastic parts is lower, the production efficiency is higher while energy is saved.展开更多
In order to study the effect of two-stage injection on two-stroke diesel engines, a well characterized research engine equipped with electronically controlled common rail system and scavenging system was constructed. ...In order to study the effect of two-stage injection on two-stroke diesel engines, a well characterized research engine equipped with electronically controlled common rail system and scavenging system was constructed. Through analysis of combustion and emissions, two-stage injection shows its advantages. Compared with the standard injection, it produces less emissions, while compared with single early injection, it expands engine operation range. Further experiments were carried out to study the influence of several injection control parameters on two-stage injection. The fuel in the first injection is used for forming homogeneous mixture. The fuel in the second injection keeps combustion, and it is the main source of smoke emissions. NO_x is formed in both combustion process caused by these two injections, and there is an optimum fuel allocation ration to produce minimum NO_x. The cylinder pressure decreases, and the combustion is depressed with the increasing of scavenging pressure. By optimizing the injection control parameters of two-stage injection, NO_x and smoke can be reduced beyond 30% simultaneously.展开更多
The depletion of fossil diesel fuels, global warming concerns and strict limits on regulated pollutant emissions are encouraging the use of renewable fuels. Biodiesel is the most used renewable fuel in compression ign...The depletion of fossil diesel fuels, global warming concerns and strict limits on regulated pollutant emissions are encouraging the use of renewable fuels. Biodiesel is the most used renewable fuel in compression ignition (CI) engine. The majority of literature agrees that the particulate matter (PM), unburnt total hydrocarbons (THC) and carbon dioxide (CO) emission from biodiesel are lower than from conventional diesel fuel. One of the most important reasons for this is the oxygen content of the biodiesel. This induces a more complete and cleaner combustion process. In addition to this the absence of aromatic compounds in biodiesel leads to particulate matter reduction with respect to diesel fuel. The potential emission benefits induced by the presence of oxygen in fuel molecules has increased the interest in using the bio-alcohols fuel blends in CI engines such as ethanol. Although alcohols are more suitable for blending with diesel fuel, properties like lubricity, viscosity, stability, heating value and cetane number of diesel-alcohol (Diesohol) still require improvement. One of the techniques is addition of biodiesel which can improve all of these properties forming diesel-biodiesel-alcohol (ternary) blends. The blends of diesel-biodiesel-ethanol can be used in the existing CI engines without any major modifications and most significant result of using this blend is the lower emission with almost the same performance as of diesel fuel alone. The present study focused on investigation of performance and combustion characteristics of ternary fuel blend in DI diesel engine operating at different injection opening pressure (IOP). The different injection opening pressures are: 180 bar, 200 bar and 220 bar.展开更多
A set of compressed natural gas (CNG) multi-point direct injection system of spark-ignited engines and the corresponding measurement and data acquisition systems were developed in this paper. Based on different inject...A set of compressed natural gas (CNG) multi-point direct injection system of spark-ignited engines and the corresponding measurement and data acquisition systems were developed in this paper. Based on different injection modes, the mixture formation and combustion of CNG low-pressure direct injection (LPDI) engines were studied under varying factors such as air/ fuel ratio, injection timing. Meanwhile, three-dimensional simulations were adopted to explain the mixture formation mechanisms of CNG low-pressure compound direct injection (LPCDI) mode. On the basis of test results and simulation of the mixture homogeneous degree, the conception of injection window was proposed, and the LPCDI mode was proved to be more beneficial to the mixture concentration stratification formation in cylinder under lean-burning conditions, which resulted in effective combustion and stability.展开更多
In order to improve the performance of the rotary engine,this paper has designed a new type of dual-pit rotary engine combustion chamber structure,and compares the combustion and emission characteristics with the rota...In order to improve the performance of the rotary engine,this paper has designed a new type of dual-pit rotary engine combustion chamber structure,and compares the combustion and emission characteristics with the rotary engine with a traditional combustion chamber.The existence of the dual-pit combustion chamber strengthens the overall vortex intensity in the cylinder,effectively promotes the mixing process of fuel and air in the cylinder,the maximum combustion pressure in the cylinder increased by 8.6%,significantly increases the diffusion combustion speed,and significantly improves the dynamic performance of the rotary engine.On this basis,the effects of fuel injection timing parameters on fuel distribution,combustion and emission characteristics were studied.Fuel distribution is more even and dispersed during injection in the later stage of compression.When the fuel injection timing was 105°BTDC in the middle of the compression phase,the matching effect of fuel distribution law and ignition scheme was the best.When the injection timing was 75°BTDC and 85°BTDC in the late compression stage,the mass fraction of NOx remained at a low level.The correlation between soot generation and the change of fuel injection timing was weak.When the injection time was 85°BTDC,the soot generation remained at a relatively high level.展开更多
This study was carried out to predict the impact of injection timing and injection duration on engine brake power and Nitrogen Oxides emissions in a diesel engine using biofuel Soya Methyl Ester (SME). Predictions wer...This study was carried out to predict the impact of injection timing and injection duration on engine brake power and Nitrogen Oxides emissions in a diesel engine using biofuel Soya Methyl Ester (SME). Predictions were accomplished at three different injection timings 10<span style="white-space:nowrap;">°</span>, 5<span style="white-space:nowrap;">°</span> Crank Angle (CA) before Top Dead Center (bTDC) and 0<span style="white-space:nowrap;">° </span>CA at Top Dead Center (TDC) and four injection durations 20<span style="white-space:nowrap;">°</span>, 25<span style="white-space:nowrap;">°</span>, 30<span style="white-space:nowrap;">°</span>, 35<span style="white-space:nowrap;">°</span> CA. The study was conducted using a simulation software (Diesel-RK). The predicted results showed that the power<span style="font-family:Verdana;"><span style="font-family:Verdana;"><span style="font-family:Verdana;">s</span></span></span><span style="font-family:Verdana;"><span style="font-family:Verdana;"><span style="font-family:Verdana;"> produced by all the setups of the different injection timings </span></span></span><span style="font-family:Verdana;"><span style="font-family:Verdana;"><span style="font-family:Verdana;">are</span></span></span><span style="font-family:Verdana;"><span style="font-family:Verdana;"><span style="font-family:Verdana;"> almost equal, but they differ in injection durations, e.g. the power at setup (10<span style="white-space:nowrap;">°</span> CA</span></span></span><span style="font-family:Verdana;"><span style="font-family:Verdana;"><span style="font-family:Verdana;">-</span></span></span><span style="font-family:Verdana;"><span style="font-family:Verdana;"><span style="font-family:Verdana;">bTDC) duration 20<span style="white-space:nowrap;">°</span> CA and 2500 rpm equal to 52 kW, at setup (5<span style="white-space:nowrap;">°</span> CA</span></span></span><span style="font-family:Verdana;"><span style="font-family:Verdana;"><span style="font-family:Verdana;">-</span></span></span><span style="font-family:Verdana;"><span style="font-family:Verdana;"><span style="font-family:Verdana;">bTDC) duration 25<span style="white-space:nowrap;">° </span>CA and same engine speed the power is equal to 51 kW, and at setup (0<span style="white-space:nowrap;">°</span> CA</span></span></span><span style="font-family:Verdana;"><span style="font-family:Verdana;"><span style="font-family:Verdana;">-</span></span></span><span style="font-family:Verdana;"><span style="font-family:Verdana;"><span style="font-family:Verdana;">TDC) durations 30<span style="white-space:nowrap;">°</span> the power is equal to 51 kW. The power in all setups are decreased as the injection duration increased, e.g. at setup 0<span style="white-space:nowrap;">°</span> CA TDC durations 25<span style="white-space:nowrap;">°</span>, 35<span style="white-space:nowrap;">°</span>, and 40<span style="white-space:nowrap;">°</span> CA and at 4000 rpm, the brake powers are equal 71, 65, and 59 kW respectively, thus the reduction percentages are 9% and 17% when compared to the 25<span style="white-space:nowrap;">°</span> injection duration. The nitrogen oxides emissions decreased as the injection duration is increased, e.g. the emissions at setup (10<span style="white-space:nowrap;">°</span> CA</span></span></span><span style="font-family:Verdana;"><span style="font-family:Verdana;"><span style="font-family:Verdana;">-</span></span></span><span style="font-family:Verdana;"><span style="font-family:Verdana;"><span style="font-family:Verdana;">bTDC) durations 25<span style="white-space:nowrap;">°</span>, 30<span style="white-space:nowrap;">°</span>, and 40<span style="white-space:nowrap;">°</span> CA and at 2500 rpm are equal 852, 589, 293 ppm respectively, the reduction percentages are 30% and 72%. The variations of injection timing and injection duration </span></span></span><span style="font-family:Verdana;"><span style="font-family:Verdana;"><span style="font-family:Verdana;">have </span></span></span><span style="font-family:Verdana;"><span style="font-family:Verdana;"><span style="font-family:Verdana;">taken a weighty influence on engine performance and emissions. The results </span></span></span><span style="font-family:Verdana;"><span style="font-family:Verdana;"><span style="font-family:Verdana;">are</span></span></span><span style="font-family:Verdana;"><span style="font-family:Verdana;"><span style="font-family:Verdana;"> considered as a novelty in the field of using pure biofuel Soya Methyl Ester in diesel engine according to our information.</span></span></span>展开更多
The highest-level interference essence against virus and turnour genetic engineering medicine is a new type created in the 1980s. Compared with chemical medicines, the interference essence has a special effect in the ...The highest-level interference essence against virus and turnour genetic engineering medicine is a new type created in the 1980s. Compared with chemical medicines, the interference essence has a special effect in the treatment of viruses and tumours. The human a, type genetic engineering interference essense is prepared by the Institute of Viruses of the Chinese Academy of Preventive Medical Sciences, the Shanghai Vaccine展开更多
The population which could not access to electricity was around 1.2 billion in 2010 and is distributed in many low developing countries. With the increase in the population and the economic growth in those countries, ...The population which could not access to electricity was around 1.2 billion in 2010 and is distributed in many low developing countries. With the increase in the population and the economic growth in those countries, waste generation is growing rapid especially for the organic and the plastic, and the uncontrolled waste disposal is becoming more serious issues to manage it. The interest on waste to energy is growing by the above drivers. This research was carried out for aiming to the real world adaption at the minimum cost of the pyrolysis oil from waste biomass in a diesel engine, mainly for electricity generation. The proposal of the appropriate adaptable blend ratio was the major scope rather than the optimization of the engine parameters. For the sake of it, the pyrolysis oil of the waste biomass was produced from a gasification pilot plant in Japan and blended with biodiesel at minimum effort. A small single cylinder diesel engine (direct injection) was used for the experiment with regard to full load power-output, exhaust emissions and fuel consumption.展开更多
Based on the analysis of the advantages of the Natural Gas Engine with Direct Injection (NGEDI) and the state of the art of the research in this area, the authors point out that, the NGEDI with high pressure is one ...Based on the analysis of the advantages of the Natural Gas Engine with Direct Injection (NGEDI) and the state of the art of the research in this area, the authors point out that, the NGEDI with high pressure is one potential selection and will have a good application prospects. Through investigation experiment and simulation results, the key techniques are put foreword for deployment of the NGEDI and some solutions are given.展开更多
The application of computer simulation technique to electronic controlled fuel injection(EFI) engine was studied to increase the development speed and improve the overall performance of the engine and car. On the bas...The application of computer simulation technique to electronic controlled fuel injection(EFI) engine was studied to increase the development speed and improve the overall performance of the engine and car. On the basis of an EFI system developed by ourselves, the simulation model of the initial control data and engine operation points during a driving cycle and the car performance pridiction model were established. This method was applied to a mini car. The experiment showed that the simulated control data has good accuracy; and the engine test points and car performances obtained by simulation are useful for the matching of EFI system with gasoline engine and the development speed is increased.展开更多
文摘Biodiesel fuel is a potential alternative energy source for diesel engines due to its physiochemical characteristics relatively similar to those of traditional diesel fuel.In this study,the performance,emission,and combustion features of a mono cylinder DI diesel engine are assessed using 20%Pumpkin seed methyl ester(PSOME20)and considering varying injection pressures(200,220,240,and 260 bar).The considered Pumpkin seed oil is converted into pumpkin biodiesel by transesterification and then used as fuel.The findings demonstrate that the Brake Thermal Efficiency(BTE)of PSOME20 can be raised by 1.68%,and the carbon monoxide(CO),hydrocarbon(HC),and smoke emanations can be lowered,while oxides of nitrogen(NOx)emissions are increased at an injection pressure(IP)of 240 bar compared to the standard IP of 200 bar.The cylinder pressure and the Heat Release Rate(HRR)become higher at 240 bar,whereas the ignition delay is shortened with respect to PSOME20 at a normal IP of 200 bar.
文摘A thermoelectric generation Stirling engine (TEG-Stirling engine) is discussed by employing a low temperature Stirling engine and the dissipative equation of motion derived from the method of thermomechanical dynamics (TMD). The results and mechanism of axial flux electromagnetic induction (AF-EMI) are applied to a low temperature Stirling engine, resulting in a TEG-Stirling engine. The method of TMD produced thermodynamically consistent and time-dependent physical quantities for the first time, such as internal energy ℰ(t), thermodynamic work Wth(t), the total entropy (heat dissipation) Qd(t)and measure or temperature of a nonequilibrium state T˜(t). The TMD analysis produced a lightweight mechanical system of TEG-Stirling engine which derives electric power from waste heat of temperature (40˚CT100˚C) by a thermoelectric conversion method. An optimal low rotational speed about 30θ′(t)/(2π)60(rpm) is found, applicable to devices for sustainable, clean energy technologies. The stability of a thermal state and angular rotations of TEG-Stirling engine are specifically shown by employing properties of nonequilibrium temperature T˜(t), which is also applied to study optimal fuel-injection and combustion timings of heat engines.
基金Project(2011BAE22B05)supported by the National Science and Technology Pillar Program during the 12th Five-year Plan of China
文摘Combustion noise takes large proportion in diesel engine noise and the studies of its influence factors play an important role in noise reduction. Engine noise and cylinder pressure measurement experiments were carried out. And the improved attenuation curves were obtained, by which the engine noise was predicted. The effect of fuel injection parameters in combustion noise was investigated during the combustion process. At last, the method combining single variable optimization and multivariate combination was introduced to online optimize the combustion noise. The results show that injection parameters can affect the cylinder pressure rise rate and heat release rate, and consequently affect the cylinder pressure load and pressure oscillation to influence the combustion noise. Among these parameters, main injection advance angle has the greatest influence on the combustion noise, while the pilot injection interval time takes the second place, and the pilot injection quantity is of minimal impact. After the optimal design of the combustion noise, the average sound pressure level of the engine is distinctly reduced by 1.0 d B(A) generally. Meanwhile, the power, emission and economy performances are ensured.
基金This project is supported by National Natural Science Foundation of China(No. 50676107)State Key Laboratory of Automotive Safety and Energyof China (No. KF2006-07).
文摘Experiments are conducted to develop an understanding of how split injections can affect the combustion and emission characteristics of a D.I. diesel engine with a common-rail injection system. The ratio of the amount of fuel injected between two injection pulses and the injection interval is varied keeping the injected fuel quantity constant. Results show that under the 70D90-10 injection pattern, the engine achieves the lower NOx-smoke emissions and BSFC compared with the single injection pattern. The heat release rate and the temperature show that the split injections increase the initial premixed burn and retards the diffusion burn. With the balance of these two effects, the maximum in-cylinder temperature decreases while the 50% heat release point is held at almost the same crank angle. Therefore, both NOx emission and BSFC are improved while keeping the smoke emission at the same level.
基金supported by the Ministry of Science and Technology of the People’s Republic of China[grant numbers 2017YFC0211304]the Natural Science Foundation of Shandong Province[grant number ZR2019MEE041]the Open Fund of the National Engineering Laboratory for Mobile Source Emission Control Technology[grant number NELMS2017A14].
文摘In order to effectively implement DPF(Diesel Particulate Filters)regeneration control,thermal management of exhaust products before and inside Diesel Oxidation Catalyst(DOC)is necessary.In the present study,the Influence of the intake throttle valve and late post injection process on temperature rise inside DOC is analyzed through engine bench tests.The steady experiment results show that adjustment of the intake throttle valve can effectively increase exhaust temperature before DOC;in particular,with intake throttle valve opening at 20%,temperature before DOC can be increased by about 170℃ with respect to the full opening.An increase in the late post injection quantity can produce a significant rise of the temperature inside DOC,however its impact on the exhaust temperature before DOC is relatively limited.As the late post injection quantity increases,Hydrocarbon(HC)emissions also grow;in the present work it is shown that with a proper injection quantity,a considerable temperature increase inside the DOC can be obtained with relatively low HC emission.More specifically,with the intake throttle valve at 30%and DOC reaching ignition temperature as the late post injection quantity is increased,the exhaust temperature after DOC can be made larger than 550℃,adequate for DPF active regeneration.
基金Supported by the Program for New Century Excellent Talents in University(NECT-11-0826) the National Natural Science Foundation of China(NSFC 51279037)+1 种基金 the Fundamental Research Funds for the Central Universities(HEUCFZ13) the Postdoctoral Science-research Developmental Foundation of Heilongjiang Province(LBH-Q12126)Acknowledgement The authors gratefully acknowledge vice Professor Yong Shi and Jun Sun's help in fuel injection experiment.
文摘A simulation model of an electronically controlled two solenoid valve fuel injection system for a diesel engine is established in the AMESim environment.The accuracy of the model is validated through comparison with experimental data.The influence of pre-injection control parameters on main-injection quantity under different control modes is analyzed.In the spill control valve mode,main-injection fuel quantity decreases gradually and then reaches a stable level because of the increase in multi-injection dwell time.In the needle control valve mode,main-injection fuel quantity increases with rising multi-injection dwell time;this effect becomes more obvious at high-speed revolutions and large main-injection pulse widths.Pre-injection pulse width has no obvious influence on main-injection quantity under the two control modes;the variation in main-injection quantity is in the range of 1 mm3.
基金This project is supported by the Commission of Science Technology and Industry for National Defense, China(No.MKPT-02-291).
文摘A direct injection low compression ratios diesel rotary engine is designed and studied to find the appropriate application of the electronic controlled high pressure common rail injection system. Current development focuses on the applied fuel injection and ignition strategies, especially concerning the combustion configurations of injectors, ignition source, and combustion chamber. The prototype engine, equipped with Bosch common rail system and high performance electronic control unit (ECU), is designed correspondingly. Studies show that the integration of a common rail injection system and the main and pilot duel injectors configurations, assisted with glow plug ignition device and flexible ECU, represents a promising approach to improve the potential of the low compression ratios diesel rotary engine. Currently the engine can run at 6 kr · min^-1 steadily and the power is about 68 kW/(4 kr ·min^- 1).
文摘This study investigated the relationship between a subject’s evaluation of injection molding machines (IMMs) and formal design features using Kansei engineering. This investigation used 12 word pairs to evaluate the IMM configurations and employed the semantic differential method to explore the perception of 60 interviewees of 12 examples. The relationship between product feature design and corresponding words was derived by multiple regression analysis. Factor analysis reveals that the 12 examples can be categorized as two styles—advanced style and succinct style. For the advanced style, an IMM should use a rectangular form for the clamping-unit cover and a full-cover for the injection-unit. For the succinct style, the IMM configuration should use a beveled form for the safety cover and a vertical rectangular form for the clamping-unit cover. Quantitative data and suggested guidelines for the relationship between design features and interviewee evaluations are useful to product designers when formulating design strategies.
基金Supported by the National Natural Science Foundation of China(51605447)
文摘The effects of various split injection strategies on the opposed-piston opposed-cylinder(OPOC)diesel engine combustion and emission characteristics have been studied numerically using AVL-Fire CFD tools.The five rate-shaped main injections were used in split injection strategies.The results show that ignition delay from a rectangular injection rate is the shortest.Maximum pressure of the trapezoid injection rate is the largest.And the NOx emission of the rectangular injection rate is the largest.Meanwhile,the soot emission of the trapezoid injection rate is the least among the five injection rates.
文摘Presents the conception of concurrent engineering employed for CAD/CAM of injection moulds by closely combining the management science with the manufacturing techniques with the cost of processing, material cost, etc taken into consideration from the conceptural design to delivery of products and concludes with the results of analyses that the cost of finished plastic parts is lower, the production efficiency is higher while energy is saved.
基金The National Basic Research Program of China(973 Program)(No.2001CB209208)The National Science Foundation of China(No.50136040)
文摘In order to study the effect of two-stage injection on two-stroke diesel engines, a well characterized research engine equipped with electronically controlled common rail system and scavenging system was constructed. Through analysis of combustion and emissions, two-stage injection shows its advantages. Compared with the standard injection, it produces less emissions, while compared with single early injection, it expands engine operation range. Further experiments were carried out to study the influence of several injection control parameters on two-stage injection. The fuel in the first injection is used for forming homogeneous mixture. The fuel in the second injection keeps combustion, and it is the main source of smoke emissions. NO_x is formed in both combustion process caused by these two injections, and there is an optimum fuel allocation ration to produce minimum NO_x. The cylinder pressure decreases, and the combustion is depressed with the increasing of scavenging pressure. By optimizing the injection control parameters of two-stage injection, NO_x and smoke can be reduced beyond 30% simultaneously.
文摘The depletion of fossil diesel fuels, global warming concerns and strict limits on regulated pollutant emissions are encouraging the use of renewable fuels. Biodiesel is the most used renewable fuel in compression ignition (CI) engine. The majority of literature agrees that the particulate matter (PM), unburnt total hydrocarbons (THC) and carbon dioxide (CO) emission from biodiesel are lower than from conventional diesel fuel. One of the most important reasons for this is the oxygen content of the biodiesel. This induces a more complete and cleaner combustion process. In addition to this the absence of aromatic compounds in biodiesel leads to particulate matter reduction with respect to diesel fuel. The potential emission benefits induced by the presence of oxygen in fuel molecules has increased the interest in using the bio-alcohols fuel blends in CI engines such as ethanol. Although alcohols are more suitable for blending with diesel fuel, properties like lubricity, viscosity, stability, heating value and cetane number of diesel-alcohol (Diesohol) still require improvement. One of the techniques is addition of biodiesel which can improve all of these properties forming diesel-biodiesel-alcohol (ternary) blends. The blends of diesel-biodiesel-ethanol can be used in the existing CI engines without any major modifications and most significant result of using this blend is the lower emission with almost the same performance as of diesel fuel alone. The present study focused on investigation of performance and combustion characteristics of ternary fuel blend in DI diesel engine operating at different injection opening pressure (IOP). The different injection opening pressures are: 180 bar, 200 bar and 220 bar.
基金Supported by National High Technology Research and Development Program ("863" Program) of China (No.2008AA11A114)
文摘A set of compressed natural gas (CNG) multi-point direct injection system of spark-ignited engines and the corresponding measurement and data acquisition systems were developed in this paper. Based on different injection modes, the mixture formation and combustion of CNG low-pressure direct injection (LPDI) engines were studied under varying factors such as air/ fuel ratio, injection timing. Meanwhile, three-dimensional simulations were adopted to explain the mixture formation mechanisms of CNG low-pressure compound direct injection (LPCDI) mode. On the basis of test results and simulation of the mixture homogeneous degree, the conception of injection window was proposed, and the LPCDI mode was proved to be more beneficial to the mixture concentration stratification formation in cylinder under lean-burning conditions, which resulted in effective combustion and stability.
基金National Natural Science Foundation of China No.51976083 and the Qing Lan Project.
文摘In order to improve the performance of the rotary engine,this paper has designed a new type of dual-pit rotary engine combustion chamber structure,and compares the combustion and emission characteristics with the rotary engine with a traditional combustion chamber.The existence of the dual-pit combustion chamber strengthens the overall vortex intensity in the cylinder,effectively promotes the mixing process of fuel and air in the cylinder,the maximum combustion pressure in the cylinder increased by 8.6%,significantly increases the diffusion combustion speed,and significantly improves the dynamic performance of the rotary engine.On this basis,the effects of fuel injection timing parameters on fuel distribution,combustion and emission characteristics were studied.Fuel distribution is more even and dispersed during injection in the later stage of compression.When the fuel injection timing was 105°BTDC in the middle of the compression phase,the matching effect of fuel distribution law and ignition scheme was the best.When the injection timing was 75°BTDC and 85°BTDC in the late compression stage,the mass fraction of NOx remained at a low level.The correlation between soot generation and the change of fuel injection timing was weak.When the injection time was 85°BTDC,the soot generation remained at a relatively high level.
文摘This study was carried out to predict the impact of injection timing and injection duration on engine brake power and Nitrogen Oxides emissions in a diesel engine using biofuel Soya Methyl Ester (SME). Predictions were accomplished at three different injection timings 10<span style="white-space:nowrap;">°</span>, 5<span style="white-space:nowrap;">°</span> Crank Angle (CA) before Top Dead Center (bTDC) and 0<span style="white-space:nowrap;">° </span>CA at Top Dead Center (TDC) and four injection durations 20<span style="white-space:nowrap;">°</span>, 25<span style="white-space:nowrap;">°</span>, 30<span style="white-space:nowrap;">°</span>, 35<span style="white-space:nowrap;">°</span> CA. The study was conducted using a simulation software (Diesel-RK). The predicted results showed that the power<span style="font-family:Verdana;"><span style="font-family:Verdana;"><span style="font-family:Verdana;">s</span></span></span><span style="font-family:Verdana;"><span style="font-family:Verdana;"><span style="font-family:Verdana;"> produced by all the setups of the different injection timings </span></span></span><span style="font-family:Verdana;"><span style="font-family:Verdana;"><span style="font-family:Verdana;">are</span></span></span><span style="font-family:Verdana;"><span style="font-family:Verdana;"><span style="font-family:Verdana;"> almost equal, but they differ in injection durations, e.g. the power at setup (10<span style="white-space:nowrap;">°</span> CA</span></span></span><span style="font-family:Verdana;"><span style="font-family:Verdana;"><span style="font-family:Verdana;">-</span></span></span><span style="font-family:Verdana;"><span style="font-family:Verdana;"><span style="font-family:Verdana;">bTDC) duration 20<span style="white-space:nowrap;">°</span> CA and 2500 rpm equal to 52 kW, at setup (5<span style="white-space:nowrap;">°</span> CA</span></span></span><span style="font-family:Verdana;"><span style="font-family:Verdana;"><span style="font-family:Verdana;">-</span></span></span><span style="font-family:Verdana;"><span style="font-family:Verdana;"><span style="font-family:Verdana;">bTDC) duration 25<span style="white-space:nowrap;">° </span>CA and same engine speed the power is equal to 51 kW, and at setup (0<span style="white-space:nowrap;">°</span> CA</span></span></span><span style="font-family:Verdana;"><span style="font-family:Verdana;"><span style="font-family:Verdana;">-</span></span></span><span style="font-family:Verdana;"><span style="font-family:Verdana;"><span style="font-family:Verdana;">TDC) durations 30<span style="white-space:nowrap;">°</span> the power is equal to 51 kW. The power in all setups are decreased as the injection duration increased, e.g. at setup 0<span style="white-space:nowrap;">°</span> CA TDC durations 25<span style="white-space:nowrap;">°</span>, 35<span style="white-space:nowrap;">°</span>, and 40<span style="white-space:nowrap;">°</span> CA and at 4000 rpm, the brake powers are equal 71, 65, and 59 kW respectively, thus the reduction percentages are 9% and 17% when compared to the 25<span style="white-space:nowrap;">°</span> injection duration. The nitrogen oxides emissions decreased as the injection duration is increased, e.g. the emissions at setup (10<span style="white-space:nowrap;">°</span> CA</span></span></span><span style="font-family:Verdana;"><span style="font-family:Verdana;"><span style="font-family:Verdana;">-</span></span></span><span style="font-family:Verdana;"><span style="font-family:Verdana;"><span style="font-family:Verdana;">bTDC) durations 25<span style="white-space:nowrap;">°</span>, 30<span style="white-space:nowrap;">°</span>, and 40<span style="white-space:nowrap;">°</span> CA and at 2500 rpm are equal 852, 589, 293 ppm respectively, the reduction percentages are 30% and 72%. The variations of injection timing and injection duration </span></span></span><span style="font-family:Verdana;"><span style="font-family:Verdana;"><span style="font-family:Verdana;">have </span></span></span><span style="font-family:Verdana;"><span style="font-family:Verdana;"><span style="font-family:Verdana;">taken a weighty influence on engine performance and emissions. The results </span></span></span><span style="font-family:Verdana;"><span style="font-family:Verdana;"><span style="font-family:Verdana;">are</span></span></span><span style="font-family:Verdana;"><span style="font-family:Verdana;"><span style="font-family:Verdana;"> considered as a novelty in the field of using pure biofuel Soya Methyl Ester in diesel engine according to our information.</span></span></span>
文摘The highest-level interference essence against virus and turnour genetic engineering medicine is a new type created in the 1980s. Compared with chemical medicines, the interference essence has a special effect in the treatment of viruses and tumours. The human a, type genetic engineering interference essense is prepared by the Institute of Viruses of the Chinese Academy of Preventive Medical Sciences, the Shanghai Vaccine
文摘The population which could not access to electricity was around 1.2 billion in 2010 and is distributed in many low developing countries. With the increase in the population and the economic growth in those countries, waste generation is growing rapid especially for the organic and the plastic, and the uncontrolled waste disposal is becoming more serious issues to manage it. The interest on waste to energy is growing by the above drivers. This research was carried out for aiming to the real world adaption at the minimum cost of the pyrolysis oil from waste biomass in a diesel engine, mainly for electricity generation. The proposal of the appropriate adaptable blend ratio was the major scope rather than the optimization of the engine parameters. For the sake of it, the pyrolysis oil of the waste biomass was produced from a gasification pilot plant in Japan and blended with biodiesel at minimum effort. A small single cylinder diesel engine (direct injection) was used for the experiment with regard to full load power-output, exhaust emissions and fuel consumption.
文摘Based on the analysis of the advantages of the Natural Gas Engine with Direct Injection (NGEDI) and the state of the art of the research in this area, the authors point out that, the NGEDI with high pressure is one potential selection and will have a good application prospects. Through investigation experiment and simulation results, the key techniques are put foreword for deployment of the NGEDI and some solutions are given.
文摘The application of computer simulation technique to electronic controlled fuel injection(EFI) engine was studied to increase the development speed and improve the overall performance of the engine and car. On the basis of an EFI system developed by ourselves, the simulation model of the initial control data and engine operation points during a driving cycle and the car performance pridiction model were established. This method was applied to a mini car. The experiment showed that the simulated control data has good accuracy; and the engine test points and car performances obtained by simulation are useful for the matching of EFI system with gasoline engine and the development speed is increased.