Shock response of cyclotetramethylene tetranitramine(HMX)single crystal at elevated temperatures

To investigate the shock response of cyclotetramethylene tetranitramine(HMX)single crystals at elevated temperatures(below the phase transition point),plate impact experiments at elevated temperatures were designed and conducted.The HMX/window interface particle velocities at temperatures of 300 K,373 K,and 423 K were measured by the velocity interferometry system for any reflector(VISAR)technique.To further analyze the related mesoscale deformation mechanisms,a nonlinear thermoelastic-viscoplastic model was developed,which considers thermal activation and phonon drag dislocation slip mechanisms.The proposed model could well reproduce the measured thermal hardening behavior of Hugoniot elastic limit(HEL)of HMX single crystals.At elevated temperatures,the reduced dislocation mobility was observed,which stems from both phonon scattering and radiative damping effects.Comparatively speaking,radiative damping contributes less than phonon scattering to thermal hardening behavior.The calibrated model was further used to predict shock response of HMX single crystals with different thicknesses at different initial temperatures.Both the stress relaxation and elastic precursor decrease with thickness are mainly due to the rapid dislocation generation.These insights shed light on the interplay between dislocation motion and dislocation generation in thermal hardening behavior,stress relaxation,and elastic precursor decay,which serves to reveal the mesoscale deformation mechanisms at elevated temperatures.

Ascending aorta dilatation reduces the influence of elevated pulse pressure on left ventricular hypertrophy:findings from a Chinese elderly hypertensive population

OBJECTIVE To determine the role of ascending aorta dilatation in the relationship between pulse pressure(PP)and left ventricular(LV)hypertrophy.METHODS A total of 1556 Chinese elderly hypertensive patients were retrospectively studied.Transthoracic echocardiography was used to obtain the aortic and cardiac structure measurements.In addition,brachial blood pressure was measured,and total arterial compliance,systemic vascular resistance,arterial elastance,and end-systolic LV elastance were calculated.The participants were divided into four groups according to the status of ascending aortic diameter and PP.RESULTS LV mass index increased in succession in the four groups,i.e.,the group with the normal aorta and lower PP,with the normal aorta and higher PP,with aortic dilatation and lower PP,and with aortic dilatation and higher PP(Ptrend<0.001).Total arterial compliance−1,arterial elastance,and end-systolic LV elastance were slightly higher in the individuals with normal aorta compared to those with aortic dilatation,regardless of PP being lower or higher(P<0.01).Compared to the group with the normal aorta and lower PP,individuals with aortic dilatation had a significantly increased multivariable adjusted risk of LV hypertrophy,and higher PP further exacerbated this risk[aortic dilatation with lower PP(OR=1.75,95%CI:1.01–3.04)and aortic dilatation with higher PP(OR=3.42,95%CI:2.03–5.77)].In the relation between PP and LV mass index(β=0.095,P<0.001),-41.3%of the total effect was attributable to mediation by ascending aortic diameter(P<0.0001).CONCLUSIONS In Chinese elderly patients with hypertension,ascending aorta dilatation could reduce the influence of elevated PP on LV hypertrophy.

Flow softening and dynamic recrystallization behavior of a Mg-Gd-Y-Nd-Zr alloy under elevated temperature compressions

Flow softening behavior of a homogenized Mg-7Gd-4Y-1Nd-0.5Zr alloy under compression to a final strain of∼1.8 at elevated temperatures of 450∼550℃ and a constant strain rate of 2s^(−1) has been investigated by optical microscopy,scanning electron microscopy,electron back-scattered diffraction and transmission electron microscopy.The results show that true stress first rises to the peak point and then drops to the bottom value and increases again with further increasing strain at each temperature.Twinning dynamic recrystallization(DRX)and continuous DRX contribute to the formation of new fine grains at temperatures 450∼475℃ when the restoration is caused by both DRX and texture change due to extension twinning,resulting in the larger softening degrees compared with the softening effects owing to continuous DRX and discontinuous DRX at 500∼550℃ when twinning activation is suppressed.500℃ is the transition temperature denoting a significant decline in the contribution of twinning and TDRX to the strain with increasing temperature.The cuboid-shape phase exists in both homogenized and compressed samples,while the compositions are varied.

Plant N-acylethanolamines play a crucial role in defense and its variation in response to elevated CO_(2) and temperature in tomato

The ubiquitous lipid-derived molecules N-acylethanolamines(NAEs)have multiple immune functions in mammals,but their roles and mechanisms in plant defense response during changing environment remain largely unclear.Here,we found that exogenous NAE18:0 and NAE18:2 promoted defense against the necrotrophic pathogen Botrytis cinerea but suppressed defense to the hemi-biotrophic pathogen Pseudomonas syringae pv.tomato(Pst)DC3000 in tomato.The knocking-down and overexpression function analysis of the pathogen-responsive NAE synthetic gene PHOSPHOLIPASE Dγ(PLDγ)and hydrolytic gene FATTY ACID AMID HYDROLASE 1(FAAH1)revealed that the NAE pathway is crucial for plant defense response.Using exogenous applications and SA-abolished NahG plants,we unveiled the antagonistic relationship between NAE and SA in plant defense response.Elevated CO_(2) and temperature significantly changed the NAE pathway in response to pathogens,while inhibition of the NAE pathway led to the alternation of environment-mediated defense variations against Pst DC3000 in tomato,indicating that NAE pathway is associated with plant defense variations in response to elevated CO_(2) and temperature.The results herein reveal a new function of NAE in plant defense,and its involvement in environment-mediated defense variation in tomato.These findings shed light on the NAE-based plant defense,which may have relevance to crop disease management in future changing climate.

Effects of elevated CO_2 concentration and nitrogen supply on biomass and active carbon of freshwater marsh after two growing seasons in Sanjiang Plain, Northeast China

An experiments were carried out with treatments differing in nitrogen supply （0, 5 and 15 g N/m^2） and CO2 levels （350 and 700 μmol/mol） using OTC （open top chamber） equipment to investigate the biomass of Calamagrostis angustifolia and soil active carbon contents after two years. The results showed that elevated CO2 concentration increased the biomass of C. angustifolia and the magnitude of response varied with each growth period. Elevated CO2 concentration has increased aboveground biomass by 16.7% and 17.6% during the jointing and heading periods and only 3.5% and 9.4% during dough and maturity periods. The increases in belowground biomass due to CO2 elevation was 26.5%, 34.0% and 28.7% during the heading, dough and maturity periods, respectively. The responses of biomass to enhanced CO2 concentrations are differed in N levels. Both the increase of aboveground biomass and belowground biomass were greater under high level of N supply （15 g N/m^2）. Elevated CO2 concentration also increased the allocation of biomass and carbon in root. Under elevated CO2 concentration, the average values of active carbon tended to increase. The increases of soil active soil contents followed the sequence of microbial biomass carbon （10.6%） 〉 dissolved organic carbon （7.5%） 〉 labile oxidable carbon （6.6%） 〉 carbohydrate carbon （4.1%）. Stepwise regressions indicated there were significant correlations between the soil active carbon contents and plant biomass. Particularly, microbial biomass carbon, labile oxidable carbon and carbohydrate carbon were found to be correlated with belowground biomass, while dissolved organic carbon has correlation with aboveground biomass. Therefore, increased biomass was regarded as the main driving force for the increase in soil active organic carbon under elevated CO2 concentration.

Processing of AM60 magnesium alloy by hydrostatic cyclic expansion extrusion at elevated temperature as a new severe plastic deformation method

Hydrostatic cyclic expansion extrusion(HCEE) process at elevated temperatures is proposed as a method for processing less deformable materials such as magnesium and for producing long ultrafine-grained rods. In the HCEE process at elevated temperatures, high-pressure molten linear low-density polyethylene(LLDPE) was used as a fluid to eliminate frictional forces. To study the capability of the process,AM60 magnesium rods were processed and the properties were investigated. The mechanical properties were found to improve significantly after the HCEE process. The yield and ultimate strengths increased from initial values of 138 and 221 MPa to 212 and 317 MPa, respectively.Moreover, the elongation was enhanced due to the refined grains and the existence of high hydrostatic pressure. Furthermore, the microhardness was increased from HV 55.0 to HV 72.5. The microstructural analysis revealed that ultrafine-grained structure could be produced by the HCEE process. Moreover, the size of the particles decreased, and these particles thoroughly scattered between the grains. Finite element analysis showed that the HCEE was independent of the length of the sample, which makes the process suitable for industrial applications.

Nitrogen Deficiency Limited the Improvement of Photosynthesis in Maize by Elevated CO_2 Under Drought

Global environmental change affects plant physiological and ecosystem processes. The interaction of elevated CO2, drought and nitrogen （N） deficiency result in complex responses of C4 species photosynthetic process that challenge our current understanding. An experiment of maize （Zea mays L.） involving CO2 concentrations （380 or 750 μmol mol1, climate chamber）, osmotic stresses （10% PEG-6000, -0.32 MPa） and nitrogen constraints （N deficiency treated since the 144th drought hour） was carried out to investigate its photosynthesis capacity and leaf nitrogen use efficiency. Elevated CO2 could alleviate drought-induced photosynthetic limitation through increasing capacity of PEPC carboxylation （Vp~,x） and decreasing stomatal limitations （SL）. The N deficiency exacerbated drought-induced photosynthesis limitations in ambient CO2. Elevated CO2 partially alleviated the limitation induced by drought and N deficiency through improving the capacity of Rubisco carboxylation （Vmax） and decreasing SL. Plants with N deficiency transported more N to their leaves at elevated CO2, leading to a high photosynthetic nitrogen-use efficiency but low whole-plant nitrogen-use efficiency. The stress mitigation by elevated CO2 under N deficiency conditions was not enough to improving plant N use efficiency and biomass accumulation. The study demonstrated that elevated CO2 could alleviate drought-induced photosynthesis limitation, but the alleviation varied with N supplies.

Study on General Performance of Jack-up Under Elevated Condition

Method of checking for jack-up elevated performance including leg structure strength, fixation system or jacking system beating capacity, pre-load requirements, spud can beating capacity and overturning stability is suggested in this paper. As an example, a jack-up with truss legs is analyzed by finite element analysis method. This paper may be helpful to the rig owners, operators and designers.

Response of successive three generations of cotton,bollworm,Helicoverpa armigera (Hübner),fed on cotton bolls under elevated CO_2

The growth, development and consumption of successive three generations of cotton bollworm, Helicoverpa armigera （Htibner）, fed on cotton bolls grown under elevated CO2 （double-ambient vs. ambient） in open-top chambers were examined. Significant decreases in protein, total amino acid, water and nitrogen content and increases in free fatty acid were observed in cotton bolls. Changes in quality of cotton bolls affected the growth, development and food utilization of H. armigera. Significantly longer larval development duration in three successive generations and lower pupal weight of the second and third generations were observed in cotton bollworm fed on cotton bolls grown under elevated CO2. Significantly lower fecundity was also found in successive three generations of H. armigera fed on cotton bolls grown under elevated CO2. The consumption per larva occurred significant increase in successive three generations and frass per larva were also significantly increased during the second and third generations under elevated CO2. Significantly lower relative growth rate, efficiency of conversion of ingested food and significant higher relative consumption rate in successive three generations were observed in cotton bollworm fed on cotton bolls grown under elevated CO2. Significantly lower potential female fecundity, larval numbers and population consumption were found in the second and third generations of cotton bollworm fed on cotton bolls grown under elevated CO2. The integrative effect of higher larval mortality rate and lower adult fecundity resulted in significant decreases in potential population consumption in the latter two generations. The results show that elevated CO2 adversely affects cotton bolls quality, which indicates the potential population dynamics and potential population consumption of cotton bollworm will alleviate the harm to the plants in the future rising CO2 atmosphere.

CO_2 absorption with ionic liquids at elevated temperatures

COcapture with ionic liquids（ILs） has attracted many attentions, and most works focused on absorption ability at ambient temperatures, while seldom research was concerned at elevated temperatures.This not only limits the COabsorption application at elevated temperature, but also the determination of the operation condition of the COdesorption generally occurring at higher temperature. This work mainly reported COsolubilities in ILs at elevated temperatures and related properties were also provided. 1-alkyl-3-methylimidazolium bis（trifluoromethylsulfonyl）imide（[CnMIm][TfN]） ILs were selected as physical absorbents for COcapture in this work due to their relative higher COabsorption capacities and good thermal stabilities. The long-term stability tests showed that [CnMIm][TfN] is thermally stable at 393.15 K for long time. COsolubilities in [CnMIm][TfN] were systematically determined at temperatures from 353.15 K to 393.15 K. It demonstrated that COsolubility obviously increases with the increase of pressure while slightly decreases with increase of temperature. As the length of alkyl chain on the cation increases, COsolubility in ILs increases. Additionally, the thermodynamic properties including the Gibbs free energy, enthalpy, and entropy of COwere also calculated.

Influence of surface coating on Ti811 alloy resistance to fretting fatigue at elevated temperature

An extensive study of the composition distribution, bonding strength, hardness, and wear resistance of a 0Cr18Ni9 film deposited on a Ti811 titanium alloy surface by ion beam enhanced deposition （IBED） is presented. Shot peening was introduced to post-treat the modified surface to synergistically improve the fretting fatigue resistance of the Ti811 alloy at 350°C. The results indicate that the 0Cr18Ni9 film with high density, small grain size, low void radio, and high bonding strength can be prepared using IBED. As a result, the hardness, wear resistance, and fretting fatigue resistance of the Ti811 alloy are increased to a remarkable extent. Compared with shot peening treatment or IBED 0Cr18Ni9 film alone, the Ti811 titanium alloy with an IBED 0Cr18Ni9 film combined with shot peening shows a higher fretting fatigue resistance at 350°C. This is due to the synergistic effect of the high wear resistance of the film surface and the residual compressive stress induced by shot peening.

Increased sink capacity enhances C and N assimilation under drought and elevated CO_2 conditions in maize

The maintenance of rapid growth under conditions of CO2 enrichment is directly related to the capacity of new leaves to use or store the additional assimilated carbon （C） and nitrogen （N）. Under drought conditions, however, less is known about C and N transport in C4 plants and the contributions of these processes to new foliar growth. We measured the patterns of C and N accumulation in maize （Zea mays L.） seedlings using 13C and 15N as tracers in CO2 climate chambers （380 or 750 μmol mol-1） under a mild drought stress induced with 10% PEG-6000. The drought stress under ambient conditions decreased the biomass production of the maize plants; however, this effect was reduced under elevated CO2. Compared with the water-stressed maize plants under atmospheric CO2, the treatment that combined elevated CO2 with water stress increased the accumulation of biomass, partitioned more C and N to new leaves as well as enhanced the carbon resource in ageing leaves and the carbon pool in new leaves. However, the C counterflow capability of the roots decreased. The elevated CO2 increased the time needed for newly acquired N to be present in the roots and increased the proportion of new N in the leaves. The maize plants supported the development of new leaves at elevated CO2 by altering the transport and remobilization of C and N. Under drought conditions, the increased activity of new leaves in relation to the storage of C and N sustained the enhanced growth of these plants under elevated CO2.

A new die-cast magnesium alloy for applications at higher elevated temperatures of 200-300℃

The development of lightweight magnesium(Mg)alloys capable of operating at elevated temperatures of 200-300℃and the ability of using high pressure die casting for high-volume manufacturing are the most advanced developments in manufacturing critical parts for internal combustion engines used in power tools.Here we report the microstructure and mechanical properties of a newly developed die-cast Mg-RE(La,Ce,Nd,Gd)-Al alloy capable of working at higher elevated temperatures of 200-300℃.The new alloy delivers the yield strength of 94 MPa at 300℃,which demonstrates a 42%increase over the benchmark AE44 high temperature die-cast Mg alloy.The new alloy also has good stiffness at elevated temperatures with its modulus only decreasing linearly by 13%from room temperature up to 300℃.Thermal analysis shows a minor peak at 364.7℃in the specific heat curve of the new alloy,indicating a good phase stability of the alloy up to 300℃.Nd and Gd have more affinity to Al for the formation of the minority of divorced Al-RE(Nd,Gd)based compounds,and the stable Al-poor Mg_(12)RE(La_(0.22)Ce_(0.13)Nd_(0.31)Gd_(0.31))Zn_(0.39)Al_(0.13)compound acts as the continuous inter-dendritic network,which contribute to the high mechanical performance and stability of the new die-cast Mg alloy at 200-300℃.

Characterization of mechanical properties of aluminum cast alloy at elevated temperature

The tensile response, the low cycle fatigue （LCF） resistance, and the creep behavior of an aluminum （A1） cast alloy are studied at ambient and elevated temperatures. A non-contact real-time optical extensometer based on the digital image correlation （DIC） is developed to achieve strain measurements without damage to the specimen. The optical extensometer is validated and used to monitor dynamic strains during the mechanical experiments. Results show that Young＇s modulus of the cast alloy decreases with the increasing temperature, and the percentage elongation to fracture at 100 ℃ is the lowest over the temperature range evaluated from 25 ℃ to 300 ℃. In the LCF test, the fatigue strength coefficient decreases, whereas the fatigue strength exponent increases with the rising temperature. The fatigue ductility at 100 ℃. As expected, the resistance to and changes from 200 ℃ to 300 ℃. coefficient and exponent reach maximum values creep decreases with the increasing temperature

Effects of elevated CO_2 on sensitivity of six species of algae and interspecific competition of three species of alga

Effects of elevated CO, （5000 μl/L） on sensitivity comparison of six species of algae and interspecific competition of three species of algae were investigated. The results showed that, the cell densities of six species of algae grown in elevated CO2 significantly increased compared to those in ambient CO2 （360 μl/L）, and with the time prolonged, the increasing extent increased. Therefore, elevated CO2 can promote the growth of six species of algae. However, there were differences in sensitivity between six species of algae. Based on the effects of elevated CO2 on biomass, the sensitive order （from high to low） was Platymanas sp., Platymanas subcordiformis, Nitzschia closterium, Isochrysis golbana Parke 8701, Dunoliella salina, Chlorella sp., on the condition of solitary cultivation. Compared to ambient CO2, elevated CO2 promoted the growth of three species of algae, Platymanas subcordiformis, Nitzschia closterium and Isochrysis galbana Parke 8701 under the condition of mixed cultivation. The sensitivity of the three species to elevated CO2 in mixed cultivation changed a lot compared to the condition of solitary cultivation. When grown in elevated CO2 under the condition of mixed cultivation, the sensitive order from high to low were Nitzschia clostertium, Platymonas subcordiformis; and Isochrysis galbana Parke 8701. However, under the condition of solitary cultivation, the sensitive order in elevated CO2 was Isochrysis galbana Parke 8701, Nitzschia clostertium, Platymonas subcordiformis, from sensitive to less sensitive. On the day 21, the dominant algae, the sub-dominant algae and inferior algae grown in elevated CO2 did not change. However, the population increasing dynamic and composition proportion of three algal species have significantly changed.

Mechanism of Mg2+ dissolution from olivine and serpentine: Implication for bioleaching of high-magnesium nickel sulfide ore at elevated pH

To inhibit the dissolution of Mg^2+ during the bioleaching process of high-magnesium nickel sulfide ore, the effect of major bioleaching factors on the dissolution of Mg^2+ from olivine and serpentine was investigated and kinetics studies were carried out. The results indicated that the dissolution rate-controlling steps are chemical reaction for olivine and internal diffusion for serpentine. The most influential factor on the dissolution of Mg^2+ from olivine and serpentine was temperature, followed by p H and particle size. A novel method of bioleaching at elevated pH was used in the bioleaching of Jinchuan ore. The results showed that elevated pH could significantly reduce the dissolution of Mg^2+ and acid consumption along with slightly influencing the leaching efficiencies of nickel and cobalt. A model was used to explain the leaching behaviors of high-magnesium nickel sulfide ore in different bioleaching systems. The model suggested that olivine will be depleted eventually, whereas serpentine will remain because of the difference in the rate-controlling steps. Bioleaching at elevated pH is a suitable method for treating high-magnesium nickel sulfide ores.

VISCO-PLASTIC CONSTITUTIVE MODEL FOR UNIAXIAL AND MULTIAXIAL RATCHETING AT ELEVATED TEMPERATURES

Based on the experimental results of the ratcheting for SS304 stainless steel, a new visco-plastic cyclic constitutive model was established to describe the uniaxial and multiaxial ratcheting of the material at room and elevated temperatures within the framework of unified visco-plasticity. In the model, the temperature dependence of the ratcheting was emphasized, and the dynamic strain aging occurred in the temperature range of 4 00-600℃ for the material was taken into account particularly. Finally, the prediction capability of the developed model was checked by comparing to the corresponding experimental results.

Elevated temperature intensity,timing,and duration of exposure affect soybean internode elongation,mainstem node number,and pod number per plant

A study was conducted in four compartments of a polycarbonate greenhouse at Gainesville,FL, USA to investigate how a soybean(Glycine max L. Merr.) cultivar, Maverick(maturity group III, indeterminate), responded to three elevated temperatures, ELT,(day/night of 34/26 °C, 38/30 °C, and 42/34 °C) in comparison to a control growth temperature(30/22 °C).Carbon dioxide(CO_2) concentration was maintained at 700 μmol mol^(-1) in each compartment by a processor controlled air-sampling and CO_2-injection system. Three sequential experiments were conducted at different times of year(summer, autumn, and early spring)to investigate the effect of intensity, timing, and duration of ELT on soybean node number,internode elongation, mainstem length, and number of pods set per plant. At the control temperature, the soybean plants grown in the polycarbonate greenhouse were taller than field-grown plants. When plants were grown under continuous ELT applied soon after sowing or at initial flowering, the number of nodes increased with increasing ELT intensity,whereas the length of individual internodes decreased. When ELT treatment was applied during the beginning of flowering stage(R1–R2) or earlier, more nodes were produced and the length of affected internodes was decreased. When the ELT was imposed later at reproductive stage R5+ just before the beginning of seed filling, effects on node numbers and internode lengths were negligible. Short-term(10-day) duration of ELT applied at four stages from V3 to R5+ did not significantly affect final mean numbers of nodes or mean mainstem lengths. Possible mechanisms of elevated temperature effects on soybean internode elongation and node number(internode number) are discussed. Total pod numbers per plant increased linearly with mainstem node numbers and mainstem length.Furthermore, total pod numbers per plant were greatest at 34/26 °C rather than at the control temperature of 30/22 °C(and remained high at 38/30 °C). Mild increases in temperature might not threaten, but actually increase, yields of soybean in northerly zones where this crop is currently grown at slightly suboptimal temperatures. However, a sustained increase in ambient temperature would likely threaten soybean yields.

Effect of Yttrium on Microstructures and Properties at Elevated Temperature of Mg-0.8Zr-0.35Zn Alloys

The effects of Y addition on microstructures and properties of as-cast and solid solutioning and aging treated Mg-0.8Zr-0.35Zn alloys at elevated temperature (250 ℃) were investigated by the use of XJG-04 optical microscopy, JCXA-733 electron probe, D/max-rB X-ray diffractometer (XRD) and WDW-200 electronic universal material testing machine. The results show that the microstructures of as-cast and heat treated Mg-0.8Zr-0.35Zn alloys with Y addition are refined and a new phase, Mg_(24)Y_5, is formed. At 250 ℃, the strength at elevated temperature of the alloys increases with increasing amount of Y addition, but relative elongation and area reduction decreases. The tendency of brittle fracture of fractured surface at elevated temperature is enlarged and fracture is changed from ductile into cleavage.

Response of phenology- and yield-related traits of maize to elevated temperature in a temperate region

Extreme high temperatures detrimental to maize production are projected to occur more frequently with future climate change.Phenology and yield-related traits were investigated under several levels of elevated temperature in two early-maturing hybrid cultivars:Junda 6(grown in northeastern China)and Chalok 1(grown in South Korea).They were cultivated in plastic houses in Suwon,Korea(37.27°N,126.99°E)held at target temperatures of ambient(AT),AT+1.5°C,AT+3°C,and AT+5°C at one sowing date in 2013 and three different sowing dates in 2014.Vegetative and reproductive growth durations showed variation depending on sowing date,experimental year,and cultivar.Growth duration tended to decrease,but not necessarily,with temperature elevation,but somewhat increased again above a certain temperature.High temperature-dependent variation was greater during grain filling than in the vegetative period before anthesis.Elevated temperature showed no significant effects on duration or peak dates of silking and anthesis,and thus on anthesis–silking interval.Grain yield tended to decrease with temperature elevation above ambient,showing a sharper linear decrease with mean growing season temperature increase in Junda 6 than in Chalok 1.The decrease in kernel number accounted for a much greater contribution to the yield reductions due to temperature elevation than did the decrease in individual kernel weight in both cultivars.Individual harvestable kernel weight was not significantly affected by temperature elevation treatments.Kernel number showed a linear decrease with mean growth temperature from early ear formation to early grain-filling stage,with Junda 6 showing a much severer decrease than Chalok 1.Kernel number reduction due to temperature elevation was attributable more to the decrease in differentiated ovule number than to the decrease in kernel set in Chalok 1,but largely to the decrease of kernel set in Junda 6.