Experimental Investigation of Material Removal in Elliptical Vibration Cutting of Cortical Bone

To benefit tissue removal and postoperative rehabilitation,increased efficiency and accuracy and reduced operating force are strongly required in the osteotomy.A novel elliptical vibration cutting(EVC)has been introduced for bone cutting compared with conventional cutting(CC)in this paper.With the assistance of high-speed microscope imaging and the dynamometer,the material removals of cortical bone and their cutting forces from two cutting regimes were recorded and analysed comprehensively,which clearly demonstrated the chip morphology improvement and the average cutting force reduction in the EVC process.It also revealed that the elliptical vibration of the cutting tool could promote fracture propagation along the shear direction.These new findings will be of important theoretical and practical values to apply the innovative EVC process to the surgical procedures of the osteotomy.

Elliptical vibration cutting of large-size thin-walled curved surface parts of pure iron by using diamond tool with active cutting edge shift

Large-size thin-walled curved surface parts of pure iron are crucial in aerospace,national defense,energy and precision physical experiments.However,the high machining accuracy and surface quality are difficult to achieve due to the serious tool wear and deformation when machining the parts with conventional cutting tools.In this paper,an elliptical vibration cutting(EVC)with active cutting edge shift(ACES)based on a long arbor vibration device is proposed for ultraprecision machining the pure iron parts by using diamond tool.Compared with cutting at a fixed cutting edge,the influence of ACES on the EVC was analyzed.Experiments in EVC of pure iron with ACES were conducted.The evolutions of the surface roughness,surface topography,and chip morphology with tool wear in EVC with ACES are revealed.The reasonable parameters of ultraprecision machining the pure iron parts by EVC with ACES were determined.It shows that the ACES has a slight influence on the machined surface roughness and surface topography.The diamond tool life can be significantly prolonged in EVC of pure iron with ACES than that with a fixed cutting edge,so that high profile accuracy and surface quality could be obtained even at higher nominal cutting speed.A typical thin-walled curved surface pure iron part with diameter φ240 mm,height 122 mm,and wall thickness 2 mm was fabricated by the presented method,and its profile error and surface roughness achieved PV 2.2μm and Ra less than 50 nm,respectively.

Strain rate analyses during elliptical vibration cutting of Inconel 718 using finite element analysis,Taguchi method,and ANOVA

The high strain rate in metal cutting significantly affects the mechanical properties of the work piece by altering its properties.This study outlines the material strain rates during elliptical vibration cutting.The finite element analysis,Taguchi method,and analysis of variance(ANOVA)were employed to analyze the effects and contributions of cutting and vibration process parameters(feed rate,rake angle,tangential amplitude,and frequency of vibration)on the variation of strain rates during machining of Inconel 718.Taguchi signal-to-noise analysis on an L18(2^1×3^3)orthogonal array was used to determine the optimum parametric combination for the maximum strain rate,and ANOVA was applied to evaluate the significance of control parameter factors on the strain rate.The results of the finite element analysis under different conditions illustrated that the feed rate and rake angle were negatively related to the strain rate,whereas the tangential amplitude and frequency had a positive response.Furthermore,ANOVA results indicated that the effect of the feed rate,tool rake angle,vibration frequency,and tangential amplitude on the strain rate were all statistically significant,with a reliability level of 95%.Of these,the dominant parameter affecting the strain rate was the feed rate,with a percentage contribution of 40.36%.The estimation of the optimum strain rate and confirmation tests proved that the Taguchi method could successfully optimize the working conditions to obtain the desired maximum strain rate.

Design of ultrasonic elliptical vibration cutting system for tungsten heavy alloy

Nanoscale surface roughness of tungsten heavy alloy components is required in the nuclear industry and precision instruments.In this study,a high-performance ultrasonic elliptical vibration cutting(UEVC)system is developed to solve the precision machining problem of tungsten heavy alloy.A new design method of stepped bending vibration horn based on Timoshenko’s theory is first proposed,and its design process is greatly simplified.The arrangement and working principle of piezoelectric transducers on the ultrasonic vibrator using the fifth resonant mode of bending are analyzed to realize the dual-bending vibration modes.A cutting tool is installed at the end of the ultrasonic vibration unit to output the ultrasonic elliptical vibration locus,which is verified by finite element method.The vibration unit can display different three-degree-of-freedom(3-DOF)UEVC characteristics by adjusting the corresponding position of the unit and workpiece.A dual-channel ultrasonic power supply is developed to excite the ultrasonic vibration unit,which makes the UEVC system present the resonant frequency of 41 kHz and the maximum amplitude of 14.2μm.Different microtopography and surface roughness are obtained by the cutting experiments of tungsten heavy alloy hemispherical workpiece with the UEVC system,which validates the proposed design’s technical capability and provides optimization basis for further improving the machining quality of the curved surface components of tungsten heavy alloy.