Fiber optic monitoring of an anti-slide pile in a retrogressive landslide

Anti-slide piles are one of the most important reinforcement structures against landslides,and evalu-ating the working conditions is of great significance for landslide mitigation.The widely adopted analytical methods of pile internal forces include cantilever beam method and elastic foundation beam method.However,due to many assumptions involved in calculation,the analytical models cannot be fully applicable to complex site situations,e.g.landslides with multi-sliding surfaces and pile-soil interface separation as discussed herein.In view of this,the combination of distributed fiber optic sensing(DFOS)and strain-internal force conversion methods was proposed to evaluate the working conditions of an anti-sliding pile in a typical retrogressive landslide in the Three Gorges reservoir area,China.Brillouin optical time domain reflectometry(BOTDR)was utilized to monitor the strain distri-bution along the pile.Next,by analyzing the relative deformation between the pile and its adjacent inclinometer,the pile-soil interface separation was profiled.Finally,the internal forces of the anti-slide pile were derived based on the strain-internal force conversion method.According to the ratio of calculated internal forces to the design values,the working conditions of the anti-slide pile could be evaluated.The results demonstrated that the proposed method could reveal the deformation pattern of the anti-slide pile system,and can quantitatively evaluate its working conditions.

Anchoring Depth Research of Anti-Slide Piles of Anchor Bar in Soil

The model test result of earth force in the side of anti-slide pile of anchor bars was introduced.There are three groups of the tests.The loads were on the back side of the slope in two groups.The other one was loaded just behind the pile by the jack.In order to get the force of the soil,some earth-pressure boxes were used to get the earth pressure on the side of the piles.The part of the max pressure and the earth pressure was mainly focused under the slip line

Study on embedded length of piles for slope reinforced with one row of piles

The embedded length of anti-slide piles for slope is analyzed by three-dimensional elastoplastic shear strength reduction method. The effect of embedded pile length on the factor of safety and pile behavior is analyzed. Furthermore, the effects of pile spacing, pile head conditions, pile bending stiffness and soil properties on length and behavior of pile are also analyzed. The results show that the pile spacing and the pile head conditions have significant influences on the critical embedded length of pile. It is found that the critical embedded length of pile, beyond which the factor of safety does not increase, increases with the decrease in pile spacing. The smaller the pile spacing is, the larger the integrity of the reinforced slope will be. A theoretical analysis of the slip surface is also conducted, and the slip surface determined by the pressure on piles, considering the influences of both soil and piles for slope, is in agreement with the ones in previous studies.

Shaking table test for reinforcement of soil slope with multiple sliding surfaces by reinforced double-row anti-slide piles

Despite the continuous advancements of engineering construction in high-intensity areas,many engineering landslides are still manufactured with huge thrust force,and double-row piles are effective to control such large landslides.In this study,large shaking table test were performed to test and obtain multi-attribute seismic data such as feature image,acceleration,and dynamic soil pressure.Through the feature image processing analysis,the deformation characteristics for the slope reinforced by double-row piles were revealed.By analyzing the acceleration and the dynamic soil pressure time domain,the spatial dynamic response characteristics were revealed.Using Fast Fourier Transform and half-power bandwidth,the damping ratio of acceleration and dynamic soil pressure was obtained.Following that,the Seism Signal was used to calculate the spectral displacement of the accelerations to obtain the regional differences of spectral displacement.The results showed that the overall deformation mechanism of the slope originates from tension failure in the soil mass.The platform at the back of the slope was caused by seismic subsidence,and the peak acceleration ratio was positively correlated with the relative pile heights.The dynamic soil pressure of the front row piles showed an inverted"K"-shaped distribution,but that of the back row piles showed an"S"-shaped distribution.The predominant frequency of acceleration was 2.16 Hz,and the main frequency band was 0.7-6.87 Hz;for dynamic soil pressure,the two parameters became 1.15 Hz and 0.5-6.59 Hz,respectively.In conclusion,dynamic soil pressure was more sensitive to dampening effects than acceleration.Besides,compared to acceleration,dynamic soil pressure exhibited larger loss factors and lower resonance peaks.Finally,back row pile heads were highly sensitive to spectral displacement compared to front row pile heads.These findings may be of reference value for future seismic designs of double-row piles.

New method of designing anti-slide piles——the strength reduction FEM

At present,the thrust of an anti-slide pile can be worked out with some calculation methods. However,the resistance in front of the pile,the distributions of resistance and thrust,and appropriate pile length cannot be easily obtained. In this paper,the authors applied the strength-reduction finite element method (FEM) to several design cases of anti-slide piles. Using this method,it is possible to take the pile-soil interactions into consideration,obtain reasonable resistance in front of pile and the distributions of thrust and resistance,and reasonable lengths of anti-slide piles. In particular,the thrust and resistance imposed on embedded anti-slide piles can be calculated and composite anti-slide pile structures such as anchored piles and braced piles can be optimized. It is proved through the calculation examples that this method is more reliable and economical in the design of anti-slide pile.

Centrifuge and numerical modeling of h-type anti-slide pile reinforced soil-rock mixture slope

Due to the loose structure,high porosity and high permeability of soil-rock mixture slope,the slope is unstable and may cause huge economic losses and casualties.The h-type anti-slide pile is regarded as an effective means to prevent the instability of soilrock mixture slope.In this paper,a centrifuge model test was conducted to investigate the stress distribution of the h-type anti-slide pile and the evolution process of soil arching during the loading.A numerical simulation model was built based on the similar relationship between the centrifuge model and the prototype to investigate the influence factors of the pile spacing,anchored depth,and crossbeam stiffness,and some recommendations were proposed for its application.The results show that the bending moment distribution of the rear pile exhibits Wshaped,while for the front pile,its distribution resembles V-shaped.The soil arching evolution process during loading is gradually dissipated from bottom to top and from far to near.During the loading,the change of bending moment can be divided into three stages,namely,the stabilization stage,the slow growth stage,and the rapid growth stage.In engineering projects,the recommended values of the pile spacing,anchored depth,and crossbeam stiffness are 4.0d,2.0d,and 2.0EI,where d and EI are the diameter and bending stiffness of the h-type anti-slide pile respectively.

Pre-Stressed Rope Reinforced Anti-Sliding Pile

Pre-stressed rope reinforced anti-sliding pile is a composite anti-sliding structure. It is made up of pre-stressed rope and general anti-sliding pile. It can bring traditional anti-sliding pile＇s retaining performance into full play, and to treat with landslide fast and economically. The difference between them is that the pre-stressed rope will transfix the whole anti- sliding pile through a prearranged pipe in this structure. The working mechanics, the design method and economic benefit are studied. The results show that the pre-stressed rope reinforced anti-sliding pile can treat with the small and middle landslides or high slopes well and possess the notable advantage of technology and economic.

Study on distribution rule of sliding pushing force and remnant resistant sliding force acting on anti-sliding pile

Anti-slide pile is one of the important methods to administer landslide geological disaster because of its advantages.It plays important role in administering landslide.It is a premise of reasonable economy and technological advance to know the distribution rule and feature of the force between anti-sliding pile and surrounding rock.To determine the sliding force and remnant resistant sliding force,according to need of study,this paper sets up the geological model and mechanics model in term of a typical landslide,and analyzes the effect rule of sliding body distortion,strength and gravity to the pushing force and remnant resistant sliding force by use of the numerical model.The distribution rule of pushing force and remnant resistant sliding force of the type of landslide is given.

Dynamic response of a slope reinforced by double-row antisliding piles and pre-stressed anchor cables

Large-scale shaking table tests were conducted to study the dynamic response of a slope reinforced by double-row anti-sliding piles and prestressed anchor cables. The test results show that the reinforcement suppressed the acceleration amplification effectively. The axial force time histories are decomposed into a baseline part and a vibration part in this study. The baseline part of axial force well revealed the seismic slope stability, the peak vibration values of axial force of the anchor cables changed significantly in different area of the slope under seismic excitations. The peak lateral earth pressure acting on the back of the anti-sliding pile located at the slope toe was much larger than that acting on the back of the anti-sliding pile located at the slope waist. The test results indicate an obvious load sharing ratio difference between these two anti-slide piles, the load sharing ratio between the two anti-sliding piles located at the slope toe and the slope waist varied mainly in a range of 2-5. The anti-slide pile at the slope waist suppressed the horizontal displacement of the slope surface.

Ultimate end bearing capacity of rock-socketed pile based on generalized nonlinear unified strength criterion

In order to study the mechanism of bearing behavior at the tip of a pile embedded in rock, the generalized nonlinear unified strength criterion and slip line principle for resolving the differential equation systems which govern the stress field were applied to derive the ultimate end beating capacity based on some reasonable hypothesis and failure plane model. Both numerical simulation and test results were compared with the theoretic solution. The results show good consistency with each other and verify the validity of the present approach. The depth effect with respective to embedment ratio and other influence factors like geological strength index, intermediate principal stress, overburden factor, and damage on end bearing capacity were discussed in the analytical solution. The results show that the proposed yield criterion can be much better for investigating the ultimate end bearing performance of rock-socketed pile. The end bearing capacity increases with embedment ratio and the increasing degree is influenced intensely by the above parameters. Furthermore, ignoring intermediate stress effect would underestimate the strength properties of the rock material and lead to a very conservative estimation value.

Shaking Table Tests on Bridge Foundation Reinforced by Antislide Piles on Slope

Based on the requirement of seismic reinforcement of bridge foundation on slope in the Chengdu-Lanzhou railway project,a shaking table model test of anti-slide pile protecting bridge foundation in landslide section is designed and completed. By applying Wenchuan seismic waves with different acceleration peaks,the stress and deformation characteristics of bridge pile foundation and anti-slide pile are analyzed,and the failure mode is discussed. Results show that the dynamic response of bridge pile and anti-slide pile are affected by the peak value of seismic acceleration of earthquake,with which the stress and deformation of the structure increase. The maximum dynamic earth pressure and the moment of anti-slide piles are located near the sliding surface,while that of bridge piles are located at the top of the pile. Based on the dynamic response of structure,local reinforcement needs to be carried out to meet the requirement of the seismic design. The PGA amplification factor of the surface is greater than the inside,and it decreases with the increase of the input seismic acceleration peak. When the slope failure occurs,the tension cracks are mainly produced in the shallow sliding zone and the coarse particles at the foot of the slope are accumulated.

Evaluation of Unsaturated Layer Effect on Seismic Analysis of Unbraced Sheet Pile Wall

This paper is built upon the previous developments on lateral earth pressure by providing a series of analytical expressions that may be used to evaluate vertical profiles of the effective stress and the corresponding suction stress under steady-state flow conditions. Suction stress profile is modeled for one layer sand near the ground above the water level under hydrostatic conditions. By definition, the absolute magnitude of suction stress depends on both the magnitude of the effective stress parameter and matric suction itself. Thus, by developing the Rankine’s relations in seismic state, the composing method of active and passive surfaces in sides of unbraced sheet pile is examinated and the effects of soil parameter on those surfaces are evaluated by a similar process. The relations described the quantitative evaluation of lateral earth pressure on sheet pile and the effects of unsaturated layer on bending moment and embedded depth of sheet pile in soil.

3-D Simulation Study on Seismic Response of Bridge Piles in Landslide

The anti-slide support structure is widely used in the anti-seismic reinforcement of bridge foundations,but related experimental research was processing slowly. Based on the prototype of the Jiuzhaigou bridge at the Chengdu-Lanzhou Railway,a 3-D simulation model was established on the basis of the shaking table model test,and the rationality of the dynamic analysis model was verified by indicators such as the bending moment of the bridge piles,peak soil pressure,and PGA amplification factors. The results show that the inertia force of the bridge pier has an important influence on the deformation of the pile foundation. The bending moment and shearing force are larger in lateral bridge piles,and the maximum value is near the pile top. The PGA amplification factor is stronger in the back of the rear anti-slide piles and so is it in front of the bridge pier,and the soil is prone to slip and damage. The bedrock is rigid and the dynamic response is maintained at a low level. The anti-slide piles in the rear row play a major role in the anti-seismic reinforcement design,and the anti-slide piles in the front row can be used as an auxiliary support structure.

Research on Vertical Bearing Capacity of Pile Foundation under Wave Scouring

In order to analyze the influence of wave scouring on the vertical bearing behavior of the pile foundation, the finite element software ABAQUS was used to simulate the force of the pile foundation under the action of wave scouring. A three-dimensional finite element calculation model of the pile foundation was established according to the actual working conditions, and the calculation results were compared with the field test results to verify the correctness of the built model. Then, the influence of wave scouring depth and pile embedding depth on the vertical bearing behavior of pile foundation was analyzed through calculation examples. The analysis results showed that the greater the depth of wave erosion, the greater the impact on the vertical bearing behavior of the pile foundation. Meanwhile, the smaller the buried depth of the pile body, the greater the impact on the vertical bearing capacity of the pile. Thus, the reduction rate of the vertical bearing capacity under different scouring depths was obtained.

不同嵌岩深度下抗拔桩承载特性研究

以广东省江门市某工程为例,通过有限元分析软件ABAQUS,结合地勘报告及现场对桩基进行抗拔静载试验得出的荷载–位移曲线图,建立抗拔桩三维有限元模型进行数值模拟计算分析,研究不同嵌岩深度增量下抗拔桩的承载特性。研究成果表明:增加嵌岩深度可在一定程度上提高桩基抗拔承载力,但二者之间并非呈线性增长关系。当嵌岩深度增量为3D时,相较于原试桩的桩顶位移量减小54.2%,抗拔承载力提高105.2%,对桩基抗拔承载力的提高效果尤为显著。

穿越溶洞桥梁桩基嵌岩深度计算方法研究

为准确计算岩溶区桥梁桩基嵌岩深度,依托莆炎高速公路岩溶区桥梁桩基工程,分别考虑桩基竖向极限承载力、桩身稳定性和桥梁全寿命周期内溶洞溶蚀量,提出3种穿越溶洞桥梁桩基嵌岩深度计算方法,并验证3种方法的可靠性。选取34根代表性桩基对比嵌岩深度设计值与所提方法计算值,并选取1根试桩对比规范值与所提方法计算值。结果表明:34根代表性桩基中,1根桩基的嵌岩深度设计值小于考虑全寿命周期内溶洞溶蚀量的嵌岩深度计算值,占比2.9%;10根桩基的嵌岩深度设计值同时满足竖向极限承载力、桩身稳定性和桥梁全寿命周期内溶洞溶蚀量要求,且安全储备合理,占比29.5%;23根桩基存在安全储备较高问题,占比67.6%,其中14.7%的桩基嵌岩深度设计安全储备高达5倍。各规范关于桩基嵌岩深度的取值差异较大,为确保桥梁桩基承载安全,同时降低施工难度和成本,建议设计穿越溶洞桥梁桩基的合理嵌岩深度时,充分考虑桥梁全寿命周期内溶洞溶蚀量。

圆截面组合桩加固滑坡的作用机理与合理嵌固深度物理模型试验研究

目前在滑坡治理中,大截面人工挖孔桩因存在施工安全隐患大和效率低下等问题已在部分行业领域被限制使用,开展可机械化施工的圆截面组合桩研究已成为新的趋势,但当前对圆截面组合桩变形受力机理与合理嵌固深度的研究尚不够深入。基于自主研发的圆截面组合桩加固滑坡物理模型试验系统,开展了不同工况下圆截面组合桩加固滑坡的物理模型试验,分析了滑体的变形演化过程,研究了圆截面组合桩加固下滑体与抗滑桩的变形受力特征,并对比分析了不同嵌固深度和桩顶连系梁对圆截面组合桩变形特征的影响,揭示了圆截面组合桩加固滑坡的作用机理。结果表明:①滑体的变形演化过程可分为压密、匀速变形、加速变形和变形破坏4个阶段;②前后桩均存在反弯点,反弯点会随着试验进程向桩顶移动,且后桩的反弯点更接近于滑动面;③当一排桩的嵌固深度保持不变、另一排桩的嵌固深度改变时,可将36%的桩长作为合理的嵌固深度;④连系梁使后桩的最大桩顶位移减小了15.6%,而对前桩的影响不大;⑤连系梁的存在降低了滑动面处的最大桩身弯矩,从而使得桩身弯矩分布更加合理。该研究成果有望为圆截面组合桩的设计提供借鉴和参考。

Limit analysis on seismic stability of anisotropic and nonhomogeneous slopes with anti-slide piles

This study employs the limit analysis method to evaluate the seismic stability of anisotropic and nonhomogeneous slopes stabilized with anti-slide piles. The pseudo-static approach is used to simplify the earthquake load. The yield seismic acceleration factor is obtained from the optimization procedure and the results are verified with the published data. Then, the seismically-unstable slope is reinforced with anti-slide piles, and the seismic stability of the reinforced slope is explored. The results show that the anisotropy and nonhomogeneity of soils have significant effects on the stabilizing force required from the anti-slide piles and the optimal location of the pile is near the toe of the slope.

Experimental study on seismic reinforcement of bridge foundation on silty clay landslide with inclined interlayer

A shaking table test for a bridge foundation reinforced by anti-slide piles on a silty clay landslide model with an inclined interlayer was performed.The deformation characteristics of the bridge foundation piles and anti-slide piles were analyzed in different loading conditions.The dynamic response law of a silty clay landslide with an inclined interlayer was summarized.The spacing between the rear anti-slide piles and bridge foundation should be reasonably controlled according to the seismic fortification requirements,to avoid the two peaks in the forced deformation of the bridge foundation piles.The“blocking effect”of the bridge foundation piles reduced the deformation of the forward anti-slide piles.The stress-strain response of silty clay was intensified as the vibration wave field appeared on the slope.Since the vibration intensified,the thrust distribution of the landslide underwent a process of shifting from triangle to inverted trapezoid,the difference in the acceleration response between the bearing platform and silty clay landslide tended to decrease,and the spectrum amplitude near the natural vibration frequency increased.The rear anti-slide piles were able to slow down the shear deformation of the soil in front of the piles and avoid excessive acceleration response of the bridge foundation piles.

超近距箱涵顶进上跨既有地铁线路施工关键技术

以北京芙蓉路匝道箱涵顶进为工程背景,通过数值模拟、理论计算及现场监测等方法研究了箱涵顶进对既有地铁线路的影响。对工作坑支护、滑板施工、箱涵制作、箱涵顶进等施工要点进行把控,制订了科学、合理的防控措施。研究表明:箱涵顶进施工穿越既有地铁线对结构竖向和水平变形影响较大,顶推完成后结构变形呈椭圆形。采取“袖阀管注浆+非全嵌固桩”进行底板及基坑加固的方法可显著提高地基承载力,降低箱涵顶进对既有地铁线路的影响。