Ion Photon Emission Microscope for Single Event Effect Testing in CIAE

Ion photon emission microscopy （IPEM） is a new ion-induced emission microscopy. It employs a broad ion beam with high energy and low fluence rate impinging on a sample. The position of a single ion is detected by an optical system with objective lens, prism, microscope tube and charge coupled device （CCD）. A thin ZnS film doped with Ag ions is used as a luminescent material. Generation efficiency and transmission efficiency of photons in the ZnS（Ag） film created by irradiated Cl ions are calculated. A single Cl ion optical microscopic image is observed by high quantum efficiency CCD. The resolution of a single Cl ion given in this IPEM system is 6μm. Several factors influencing the resolution are discussed. A silicon diode is used to collect the electrical signals caused by the incident ions. Effective and accidental coincidence of optical images and electronic signals are illustrated. A two-dimensional map of single event effect is drawn out according to the data of effective coincidence.

Robot driver for vehicle durability emission test on chassis dynamometer

A method for a vehicle durability emission test using a robot driver insteadof human drivers on the chassis dynamometer is presented. The system architecture of vehicledurability emission test cell, the road load simulation strategy and the tele-monitoring systembased on Browser/Client structure are described. Furthermore, the construction of the robot driver,vehicle performance self-learning algorithm, multi-mode vehicle control model and vehicle speedtracking strategy based on fuzzy logic arealso discussed. Besides, the capability of controlparameters self-compensation on-line makes it possible to compensate the wear of vehicle componentsand the variety of clutch true bite point during the long term test. Experimental results show thattherobot driver can be applicable to a wide variety of vehicles and the obtained results stay withina tolerance band of ± 2 km/h. Moreover the robot driver is able to control tested vehicles withgood repeatability and consistency; therefore, this methodpresents a solution to eliminate theuncertainty of emission test results by human drivers and to ensure the accuracy and reliability ofemission test results.

Space-time evolution rules of acoustic emission location of unloaded coal sample at different loading rates

By using MTS815 rock mechanics test system,a series of acoustic emission(AE) location experiments were performed under unloading confining pressure,increasing the axial stress.The AE space-time evolution regularities and energy releasing characteristics during deformation and failure process of coal of different loading rates are compared,the influence mechanism of loading rates on the microscopic crack evolution were studied,combining the AE characteristics and the macroscopic failure modes of the specimens,and the precursory characteristics of coal failure were also analyzed quantitatively.The results indicate that as the loading rate is higher,the AE activity and the main fracture will begin earlier.The destruction of coal body is mainly the function of shear strain at lower loading rate and tension strain at higher rate,and will transform from brittleness to ductility at critical velocities.When the deformation of the coal is mainly plasticity,the amplitude of the AE ringing counting rate increases largely and the AE energy curves appear an obvious ''step'',which can be defined as the first failure precursor point.Statics of AE information shows that the strongest AE activity begins when the axial stress level was 92-98%,which can be defined as the other failure precursor point.As the loading rate is smaller,the coal more easily reaches the latter precursor point after the first one,so attention should be aroused to prevent dynamic disaster in coal mining when the AE activity reaches the first precursor point.

INVESTIGATION IN REDUCING EXHAUST EMISSIONS FROM TWO STROKE MOTORCYCLES

Test results of reducing two stroke motorcycle emissions with new type carburettors and electronic fuel injection systems are presented. Analyses and comparison between different systems are discussed. The adoption of electronically controlled injection and corresponding electronic control technique is an effective measure of prolonged vitality to improve emissions from two stroke motorcycles. Suggestions about the strategic steps of China′s motorcycle emission control are proposed.

Emission Performance of Motorcycles in Real-Road Conditions

WMTC,which means a worldwide motorcycle testing cycle,is now regarded as the most possible choice for the global motorcycle emission testing cycle,but whether or not it can be used in China is still unknown.In this study,a large number of data on the speed-time trace of motorcycles were sampled from various kinds of roads in 5 cities in China.Based on a series of criterion numbers defined,the driving character of motorcycles in the real-road conditions of China was obtained.With the aid of a specially designed program,an emission testing cycle that can indicate the driving characteristics of motorcycle in the real-road conditions was synthesized,and the exhaust emission tests of 20 motorcycles under the synchronized cycle and WMTC were carried out based on a CVS system and a motorcycle chassis dynamometer.The results show that although there do exist differences in some criterion numbers between the real-road condition and WMTC,such as proportion of idling mode,mean speed,mean running speed and the average acceleration and deceleration rates,the driving behaviors are similar.The results of exhaust emission tests indicate that the emission values of motorcycles under the synchronized cycle and WMTC have a relatively strong correlation.This means that WMTC can be introduced as a standard motorcycle emission test regulation into China.

Uniaxial compression CT and acoustic emission test on the coal crack propagation destruction process

Acoustic emission test and CT scanning are important techniques in the study of coal crack propagation. A uniaxial compression test was performed on coal samples by integrating CT and acoustic emission. The test comparison analyzes the acoustic emission load and CT images for an effective observation on the entire process, from crack propagation to the samples＇ destruction. The box dimension of the coal samples＇ acoustic emission series and the CT images were obtained through calculations by using the authors＇ own program. The results show that the fractal dimension of both the acoustic emission energy and CT image increase rapidly, indicating coal and rock mass has entered a dangerous condition. Hence, measures should be taken to unload the pressure of the coal and rock mass. The test results provide intuitive observation data for the coal meso-damage model. The test contributes to in-depth studies of coal or rock crack propagation mechanisms and provides a theoretical basis for rock burst mechanism.

APPLIED RESEARCH ON NEW MULTI-FUNCTION GASOLINE ADDITIVE

In order to assess the performance of a new cleansing and combustion-improving gasoline additive （MAZ）, and to explore the evaluation methods of additives, two engines with the same model number and performance indices, fueled with and without the MAZ gasoline additive respectively, are carried through 100 h strenuous tests on a bench. The results obtained in full load characteristic and load characteristics of different operational modes are compared. It indicates that the power, economy and emission of the engine fueled with the MAZ additive all have obvious improvement in comparison with the engine without adding the additive： the power increasing by 16.43%, specific fuel consumption （SFC） decreasing 5.39%, and the emission of CO, HC and NOx falling by 28.61%, 54.38% and 10.1% respectively. Wear and tear of the engine cylinder is weakened, and sediment of combustion chamber inner side is reduced. In addition, no negative effect on the catalytic conversion device is found.

Brittleness and fracture mechanism of sintered Dy-doped NdFeB magnets

The brittleness and fracture behaviors of the sintered and the two-stage aged Dy-doped NdFeB magnets were studied by a unique method of acoustic emission testing and Vickers hardness indentation method in this paper.A detailed analysis on the crack propagation mechanism along the grain boundary of the main grain phase(Nd,Dy)_(2)Fe_(14)B was done.By comparing the acoustic emission energy count value(E_(n))with the Vickers hardness indentation load(P),it is shown that there is a linear relationship between En and P for both the sintered and the two-stage aged Dy-doped NdFeB magnets.According to the slope of En versus P linear lines,it can be found that the two-stage aged Dy-doped NdFeB magnet is more brittle than the sintered one.It is due to that the Ndrich grain boundary phase of the two-stage aged Dy-doped NdFeB magnet is formed as thin film and uniformly distributes around the main grain phase,which plays a significant role in increasing the intrinsic coercive force of the magnet,but decreasing its interface binding strength.Therefore,the resistance of crack propagation along the grain boundary decreases and the brittleness increases.

Experimental investigation of a novel micro gas turbine with flexible switching function for distributed power system

Micro gas turbine(MGT)is widely used in small-scale distributed power systems because of its low emissions and fuel flexibility.However,the under-utilization of its exhaust heat and the low electric efficiency are the main bottlenecks that restrict its application.Additionally,the flexible switching between the power generated by the MGT and the power grid is also a key factor for keeping the secure operation of a distributed power station.Therefore,this paper conducted some experimental investigations of a 30 kW MGT to provide reference solutions for the above issues.This MGT is located at Shanghai Jiao Tong University(SJTU),which is designed by the Gas Turbine Research Institute of SJTU,and is manufactured by a turbo machinery factory in Chongqing,China.The demonstration prototype is mainly composed of a single stage centrifugal compressor,a radial turbine,a combustor,a high-speed pennanent magnet generator,and a control system.The results show that the MGT can achieve steady operation at a low rotational speed from 10000 r/min to 34000 r/min in the case of using oil lubricated bearings,which can greatly reduce the economic cost compared with the use of air bearings.At the same time,the ignition success rate of combustion chamber(CC)reaches 98%at a low rotational speed,and a wide range of stable combustion area can be obtained,because of the novel design method of combustor by referencing the way applied in an axial flow aero-engine.The MGT generating set can achieve functions,such as starting up,ignition,stable operation,loaded operation,grid-connection and stopping.This system also can realize flexibly switching from the start motor mode to the generator mode,and from grid-connected mode to off^grid mode,because the innovative multi-state switching control system is adopted.The above research work can make our state master independent intellectual property rights of micro gas turbine,rather than continue to be subject to the technological monopoly of the developed states,which can provide theoretical and experimental support for the industrialization of MGT in China.

Design and demonstration of a next-generation air quality attainment assessment system for PM_(2.5)and O_3

Due to the increasingly stringent standards, it is important to assess whether the proposed emission reduction will result in ambient concentrations that meet the standards. The Software for Model Attainment Test-Community Edition （SMAT-CE） is developed for demonstrating attainment of air quality standards of O3 and PM2.5. SMAT-CE improves computational efficiency and provides a number of advanced visualization and analytical functionalities on an integrated GIS platform. SMAT-CE incorporates historical measurements of air quality parameters and simulated air pollutant concentrations under a number of emission inventory scenarios to project the level of compliance to air quality standards in a targeted future year. An application case study of the software based on the U.S. National Ambient Air Quality Standards （NAAQS） shows that SMAT-CE is capable of demonstrating the air quality attainment of annual PM2.5 and 8-hour O3 for a proposed emission control policy.

Effects of High Temperature Oxidation on Mechanical Properties of Ti_3AlC_2

The oxidation tests of Ti_3AlC_2 were conducted at 1100 and 1200？C in air for 48 and 360 h, respectively,and the effects of high temperature oxidation on the flexural strength and hardness of Ti_3AlC_2 were investigated. The microstructure, grain size and phase compositions of Ti_3AlC_2 substrate didn＇t change after oxidation, hence the oxide removed Ti_3AlC_2 substrate maintained its initial flexural strength and hardness. However, the flexural strength of oxide retained Ti_3AlC_2 decreased by about 5%. Acoustic emission monitoring indicated that during the process of three-point bending test, the formed Al_2O_3 scale on Ti_3AlC_2 surface fractured firstly in a cleavage manner, then the substrate/oxide interface cracked,and finally the Ti_3AlC_2 substrate fractured. The mechanical degradation was caused by the preferential formation of cracks in brittle Al_2O_3 scale as well as at defective and lacunose grain boundaries of the substrate where stress concentration generated. The mechanical degradation was insensitive to oxidation temperature and time in the present conditions. In addition, the surface hardness increased significantly after oxidation due to the formed hard Al_2O_3 scale on the surface of Ti_3AlC_2 substrate.