Improving solar cell performance by increasing solar cell efficiency by various process optimization had always been a simple straight-forward methodology followed in a R&D or in a solar cell manufacturing company...Improving solar cell performance by increasing solar cell efficiency by various process optimization had always been a simple straight-forward methodology followed in a R&D or in a solar cell manufacturing company. This is also the most cost-effective practice to improve a product performance using the same technology without the need to procure alternative or expensive raw materials or by adopting advanced solar cell processing techniques. Aluminium Back Surface Field (Al-BSF) technology using multi-crystalline wafers (mc-Si) had been a well-established and a dominant product in the solar industry for more than two decades. However, as the industry progresses, the demand for high efficiency solar cells and modules started going up and full area Aluminium BSF based cells suffers from a lot of inherent limitations on cell efficiency. This is primarily due to the intrinsic high density of crystal lattice defects or otherwise called as grain boundary defects present dominantly only in mc-Si wafers. These grain boundaries tends to accumulate several defects and become trap centres which cause high recombination for minority carriers thereby exhibiting lower conversion efficiency and higher dispersion in electrical parameters in batches of tested cells. Years of research using this material have helped to derive the maximum benefits using this mc-Si wafer in producing industrial full area BSF cells and we can say with certainty that the efficiency potential has reached the saturation point with this technology. An interesting development that happened in the area of improving the final product performance using mc-Si wafers at both cell and module level, is by replacing the conventional acid texturing process with an introduction of a nano-texturing process called Metal Catalysed Chemical Etching (MCCE) using specialized chemicals which improves the light trapping capabilities by creation of inverted pyramid texture on the silicon wafer surface and thereby enabling the wafers to absorb sunlight over a broader range of wavelength and incident angle. With this development done in mc-Si wafers in recent past, it is still a daunting task to surpass cell efficiencies beyond 19.0% using this wafer source. Hence for cell manufacturing lines which use mc-Si wafers, there is always a constant need to improve the cell manufacturing processes to reduce the impact of poor intrinsic quality of mc-Si wafers and improve the final product performance without adding any significant cost factor.展开更多
文摘Improving solar cell performance by increasing solar cell efficiency by various process optimization had always been a simple straight-forward methodology followed in a R&D or in a solar cell manufacturing company. This is also the most cost-effective practice to improve a product performance using the same technology without the need to procure alternative or expensive raw materials or by adopting advanced solar cell processing techniques. Aluminium Back Surface Field (Al-BSF) technology using multi-crystalline wafers (mc-Si) had been a well-established and a dominant product in the solar industry for more than two decades. However, as the industry progresses, the demand for high efficiency solar cells and modules started going up and full area Aluminium BSF based cells suffers from a lot of inherent limitations on cell efficiency. This is primarily due to the intrinsic high density of crystal lattice defects or otherwise called as grain boundary defects present dominantly only in mc-Si wafers. These grain boundaries tends to accumulate several defects and become trap centres which cause high recombination for minority carriers thereby exhibiting lower conversion efficiency and higher dispersion in electrical parameters in batches of tested cells. Years of research using this material have helped to derive the maximum benefits using this mc-Si wafer in producing industrial full area BSF cells and we can say with certainty that the efficiency potential has reached the saturation point with this technology. An interesting development that happened in the area of improving the final product performance using mc-Si wafers at both cell and module level, is by replacing the conventional acid texturing process with an introduction of a nano-texturing process called Metal Catalysed Chemical Etching (MCCE) using specialized chemicals which improves the light trapping capabilities by creation of inverted pyramid texture on the silicon wafer surface and thereby enabling the wafers to absorb sunlight over a broader range of wavelength and incident angle. With this development done in mc-Si wafers in recent past, it is still a daunting task to surpass cell efficiencies beyond 19.0% using this wafer source. Hence for cell manufacturing lines which use mc-Si wafers, there is always a constant need to improve the cell manufacturing processes to reduce the impact of poor intrinsic quality of mc-Si wafers and improve the final product performance without adding any significant cost factor.
