Rotor End Factors for 2-D FEA of Induction Motors with Smooth or Slitted Solid Rotor

Modifying the equivalent rotor resistivity with rotor end factor in 2-dimension(2-D)finite element analysis(FEA)is an effective way to analyze the 3-dimension(3-D)solid rotor problems.For the smooth solid rotor,five different rotor end factors are discussed and compared with each other.It is theoretically clarified that the resistivity of rotor in 2-D FEA should be multiplied by the square of rotor end factors to take the 3-D end effect of solid rotor into account.For the slitted solid rotor,an improved rotor end factor is proposed based on the equivalent area algorithm of eddy currents in rotor,since the end factors of smooth solid rotor are not applicable.Finally,the time-harmonic finite element method(FEM)combined with the rotor end factor is applied to analyze the performance of solid rotor induction motor.The tested and computed results are in good agreement,which proves the effectiveness of rotor end factor for the simplication of 3-D solid rotor problems.

New Factor to Characterize Mechanism of “Strong Column-Weak Beam” of RC Frame Structures

Most reinforced concrete(RC)frame structures did not achieve the "strong column-weak beam" failure mode in recent big earthquakes, resulting in a large number of casualties and significant property loss. To deal with this serious problem, a new column-beam relative factor was proposed to characterize the relative yield situation of column ends and beam ends. By limiting the column-beam relative factor, RC frame structures could achieve the "strong column-weak beam" failure mode under the excitation of strong ground motions. The limit values of column-beam relative factor were calculated, analyzed and verified by using structural simulation models for corner columns in the bottom story of structures, which are destroyed most seriously in earthquakes. The results show that the limit values should be analyzed under bi-directional ground motion and with different axial compression ratios of columns. The peak ground acceleration(PGA)of ground motions has no significant effect on the limit values, while the type of strong ground motions has a significant effect on the limit values.

DNA End Resection:Facts and Mechanisms

DNA double-strand breaks（DSBs）,which arise following exposure to a number of endogenous and exogenous agents,can be repaired by either the homologous recombination（HR）or non-homologous end-joining（NHEJ） pathways in eukaryotic cells.A vital step in HR repair is DNA end resection,which generates a long 30single-stranded DNA（ss DNA） tail that can invade the homologous DNA strand.The generation of 30 ss DNA is not only essential for HR repair,but also promotes activation of the ataxia telangiectasia and Rad3-related protein（ATR）.Multiple factors,including the MRN/X complex,C-terminal-binding protein interacting protein（Ct IP）/Sae2,exonuclease 1（EXO1）,Bloom syndrome protein（BLM）/Sgs1,DNA2 nuclease/helicase,and several chromatin remodelers,cooperate to complete the process of end resection.Here we review the basic machinery involved in DNA end resection in eukaryotic cells.

Performanceanalysisofalowpowerlownoisetunablebandpassfilterformultiband RF front end

This paper presents a low power tunable active inductor and RF band pass filter suitable for multiband RF front end circuits. The active inductor circuit uses the PMOS cascode structure as the negative transconductor of a gyrator to reduce the noise voltage. Also, this structure provides possible negative resistance to reduce the inductor loss with wide inductive bandwidth and high resonance frequency. The RF band pass filter is realized using the proposed active inductor with suitable input and output buffer stages. The tuning of the center frequency for multiband operation is achieved through the controllable current source. The designed active inductor and RF band pass filter are simulated in 180 nm and 45 nm CMOS process using the Synopsys HSPICE simulation tool and their performances are compared. The parameters, such as resonance frequency, tuning capability, noise and power dissipation, are analyzed for these CMOS technologies and discussed. The design of a third order band pass filter using an active inductor is also presented.