Graphene prepared by non-covalent modification of sulfonated poly(ether-ether-ketone)(SPG)was combined with polyvinylidene fluoride(PVDF)/Al to improve the PVDF/Al thermal conductivity while reducing the effect of the...Graphene prepared by non-covalent modification of sulfonated poly(ether-ether-ketone)(SPG)was combined with polyvinylidene fluoride(PVDF)/Al to improve the PVDF/Al thermal conductivity while reducing the effect of the thermal resistance at the graphene-polymer interface.The regulation rule of SPG with different contents on the energy release of fluorine-containing system was studied.When the content of SPG is 4%,the peak pressure and rise rate of SPG/PVDF/Al composite powder during ignition reach the maximum of 4845.28 kPa and 8683.58 kPa/s.When the content of SPG is 5%,the PVDF/Al composite powder is completely coated by SPG,and the calorific value of the material reachs the maximum of 29.094 kJ/g.Through the design and micro-control of the composite powder,the calorific value of the material can be effectively improved,but the improvement of the mass release rate still depends on the graphene content and surface modification state.展开更多
In this paper,various core-shell structured Al—Ni@ECs composites have been prepared by a spray-drying technique.The involved ECs refer to the energetic composites(ECs)of ammonium perchlorate/nitrocellulose(AP/NC,NA)a...In this paper,various core-shell structured Al—Ni@ECs composites have been prepared by a spray-drying technique.The involved ECs refer to the energetic composites(ECs)of ammonium perchlorate/nitrocellulose(AP/NC,NA)and polyvinylidene fluoride/hexanitrohexaazaisowurtzitane(PVDF/CL-20,PC).Two Al—Ni mixtures were prepared at atomic ratios of 1:1 and 1:3 and named as Al/Ni and Al/3Ni,respectively.The thermal reactivity and combustion behaviors of Al—Ni@ECs composites have been comprehensively investigated.Results showed that the reactivity and combustion performance of Al—Ni could be enhanced by introducing both NA and PC energetic composites.Among which the Al/Ni@NA composite exhibited higher reactivity and improved combustion performance.The measured flame propagation rate(v=20.6 mm/s),average combustion wave temperature(T_(max)=1567.0°C)and maximum temperature rise rate(γ_(t)=1633.6°C/s)of Al/Ni@NA are higher than that of the Al/Ni(v=15.8 mm/s,T_(max)=858.0°C,andγ_(t)=143.5°C/s).The enhancement in combustion properties could be due to presence of the acidic gaseous products from ECs,which could etch the Al_(2)O_(3)shell on the surface of Al particles,and make the inner active Al to be easier transported,so that an intimate and faster intermetallic reaction between Al and Ni would be realized.Furthermore,the morphologies and chemical compositions of the condensed combustion products(CCPs)of Al—Ni@ECs composites were found to be different depending on the types of ECs.The compositions of CCPs are dominated with the Al—Ni intermetallics,combining with a trace amount of Al_(5)O_(6)N and Al_(2)O_(3).展开更多
Six furazano-[3,4-d]-pyridazine-based derivatives as main compounds in solid composite propellants have been investigated.It was shown that the use of some furazano-[3,4-d]-pyridazine-based derivatives as main compoun...Six furazano-[3,4-d]-pyridazine-based derivatives as main compounds in solid composite propellants have been investigated.It was shown that the use of some furazano-[3,4-d]-pyridazine-based derivatives as main compounds in solid composite propellants can considerably increase ballistic parameters compared with HMX if the compounds under consideration contain difluoramine groups.And the use of the compounds under consideration may be successful only in the presence of an active binder and 10%-30% of AP or ADN as additional oxidizers.展开更多
Copper azide(CA), as a primary explosive with high energy density, has not been practically used so far because of its high electrostatic sensitivity. The Cu2O@HKUST-1 core-shell structure hybrid material was synthesi...Copper azide(CA), as a primary explosive with high energy density, has not been practically used so far because of its high electrostatic sensitivity. The Cu2O@HKUST-1 core-shell structure hybrid material was synthesized by the “bottle around ship” methodology in this research by regulating the dissolution rate of Cu2O and the generation rate of metal-organic framework(MOF) materials. Cu2O@HKUST-1 was carbonized to form a Cu O@porous carbon(CuO@PC) composite material. CuO@PC was synthesized into a copper azide(CA) @PC composite energetic material through a gas-solid phase in-situ azidation reaction.CA is encapsulated in PC framework, which acts as a nanoscale Faraday cage, and its excellent electrical conductivity prevents electrostatic charges from accumulating on the energetic material’s surface. The CA@PC composite energetic material has a CA content of 89.6%, and its electrostatic safety is nearly 30times that of pure CA(1.47 mJ compared to 0.05 mJ). CA@PC delivers an outstanding balance of safety and energy density compared to similar materials.展开更多
Measurements were made on the contents of protein, lipid, glycogen (PLG) and water, and on caloric values and amino acids, in muscle of three mudskippers Periophthalmis cantonensis, Scarteiaos viridis and Boleophthalm...Measurements were made on the contents of protein, lipid, glycogen (PLG) and water, and on caloric values and amino acids, in muscle of three mudskippers Periophthalmis cantonensis, Scarteiaos viridis and Boleophthalmus pectinirostris collected from Haicang, Xiamen. The essential amino acids (EAA) for these fishes were also studied with radioisotopic trace method. The results showed: (1) The content of each component in tested fish muscles differed slightly, and protein was the most important component making up from 6.685% to 9.891% of the wet weight (about 44.21%-50.45% of dry weight); (2) Energy calculated from the sum of protein, lipid and glycogen in wet muscle was low (<4.3kJ/g) in these fishes, especially in B. pectinirostris (<3.1 kJ/g); the ratios of energy to protein content (E/P) also were low (<39.873 -45.535kJ/g); (3) Seventeen amino acids were determined in these three fishes. The content of the same amino acid (among the seventeen) tested in different species and sexes varied slightly. The amounts of methionine, phenylalanine lysine, arginme, histidine, threonine isoleucine and leucine which are indispensable for the needs of human beings and animals were relative-ly high, accounting for 47.35%-48.06% of the total amino acid content. (4) Leucine, isoleucine, arginme, lysine, phenylalanine, tryptophan, methionine, histidine, threonine, and valine, are essential in the diet of the three mudskippers as the radioisotopic trace method using D-[U-^(14) C]-glucose showed little or no radioactivity was incorporated into these ten amino acids.展开更多
The experimental values of the enthalpy of formation of two isomeric 3,4-and 3,5-dinitro-1-(trinitromethyl)-1H-pyrazoles have been obtained(261.5±5.0and 246.4±6.7kJ/mol for crystalline 3,4-and 3,5-dinitro-1-...The experimental values of the enthalpy of formation of two isomeric 3,4-and 3,5-dinitro-1-(trinitromethyl)-1H-pyrazoles have been obtained(261.5±5.0and 246.4±6.7kJ/mol for crystalline 3,4-and 3,5-dinitro-1-(trinitromethyl)-1H-pyrazoles,respectively).The ballistic effectiveness of these potential oxidizers in composite solid propellants was studied.It is shown that these two oxidizers may be successfully applied in metal-free compositions or with a small content of metal.For the bottom stage 3,4-dinitro-1-(trinitromethyl)-1H-pyrazole is a bit better than 3,5-dinitro-1-(trinitromethyl)-1H-pyrazole,for the upper stage the both oxidizers show the equal ballistic parameters.These oxidizers allow to create metal-free solid composite propellants with the binder percentage not lower than 19%(volume fraction),with I3spequal to 256.5-257.0sat density equal to 1.72-1.74g/cm^3.展开更多
Improved controllability and energy density of ignition agents are of great significance for the devel-opment of energetic composite materials.In this study,droplet microfluidics and emulsification tech-niques were co...Improved controllability and energy density of ignition agents are of great significance for the devel-opment of energetic composite materials.In this study,droplet microfluidics and emulsification tech-niques were combined to prepare HNS/CL-20 composite microspheres with polyglycidyl azide polymer(GAP)as the binder.The influence of binder content on the morphology of microspheres was investi-gated,and the microspheres were characterized and tested for particle size,crystal structure,thermal decomposition,dispersibility,mechanical sensitivity,combustion behavior and detonation performance.The results showed that microspheres prepared with a binder content of 3%had higher sphericity and particle size uniformity.The microspheres retained the crystal structure of both HNS and CL-20(ε-type).Compared with raw HNS,the microspheres had higher apparent activation energy,better safety per-formance,and good dispersibility.The ignition experiments and detonation performance tests show that HNS/CL-20 composite microspheres have excellent ignition performance,obvious combustion flame,and significant energy release effects,which are expected to achieve high energy and high-speed response of the igniter,thus improving the ignition reliability in special environments or systems.展开更多
纳米多孔硅由于其海绵状的孔隙结构,氧化剂很难充分填充,导致多孔硅复合含能材料多为富燃料体系;同时其孔隙率难以调节,无法精确控制氧燃比。针对以上问题,以紧密排列的单层聚苯乙烯微球为模板,通过反应性离子刻蚀(Reaction Ion Etching...纳米多孔硅由于其海绵状的孔隙结构,氧化剂很难充分填充,导致多孔硅复合含能材料多为富燃料体系;同时其孔隙率难以调节,无法精确控制氧燃比。针对以上问题,以紧密排列的单层聚苯乙烯微球为模板,通过反应性离子刻蚀(Reaction Ion Etching,RIE)技术结合金属辅助化学刻蚀(Metal-Assisted Chemical Etching,MACE)制备得到了形貌结构可控的多孔硅纳米线,通过控制RIE时间能够精准调节多孔硅复合体系的氧燃比,同时二维线状结构非常有利于氧化剂的高效填充。结果表明,在RIE时间为80s,即硅纳米线直径为150nm左右时,复合含能体系达到最佳化学计量反应平衡,能量输出最佳。同时,选用不同电阻率的硅片制备得到不同结构形貌的硅纳米线,电阻率越低,纳米复合含能体系中的硅纳米线结构越疏松多孔,不仅能够有效缩短传质传热距离,降低反应活化能,有利于增强反应放热;而且能提升燃烧性能,有利于点火,为硅基含能材料的发展提供了新的思路。展开更多
基金Funded by the National Natural Science Foundation of China(No.52104363)。
文摘Graphene prepared by non-covalent modification of sulfonated poly(ether-ether-ketone)(SPG)was combined with polyvinylidene fluoride(PVDF)/Al to improve the PVDF/Al thermal conductivity while reducing the effect of the thermal resistance at the graphene-polymer interface.The regulation rule of SPG with different contents on the energy release of fluorine-containing system was studied.When the content of SPG is 4%,the peak pressure and rise rate of SPG/PVDF/Al composite powder during ignition reach the maximum of 4845.28 kPa and 8683.58 kPa/s.When the content of SPG is 5%,the PVDF/Al composite powder is completely coated by SPG,and the calorific value of the material reachs the maximum of 29.094 kJ/g.Through the design and micro-control of the composite powder,the calorific value of the material can be effectively improved,but the improvement of the mass release rate still depends on the graphene content and surface modification state.
基金supported by the Nation Natural Science Foundation of China(Grant No.51776176)the Fundamental Research Funds for the Central Universities,China(Grant No.G2017KY0301)+1 种基金partially funded by NSAF project(Grant No.2030202)sponsored by Innovation Foundation for Doctor Dissertation of Northwestern Polytechnical University(Grant No.CX2021048)。
文摘In this paper,various core-shell structured Al—Ni@ECs composites have been prepared by a spray-drying technique.The involved ECs refer to the energetic composites(ECs)of ammonium perchlorate/nitrocellulose(AP/NC,NA)and polyvinylidene fluoride/hexanitrohexaazaisowurtzitane(PVDF/CL-20,PC).Two Al—Ni mixtures were prepared at atomic ratios of 1:1 and 1:3 and named as Al/Ni and Al/3Ni,respectively.The thermal reactivity and combustion behaviors of Al—Ni@ECs composites have been comprehensively investigated.Results showed that the reactivity and combustion performance of Al—Ni could be enhanced by introducing both NA and PC energetic composites.Among which the Al/Ni@NA composite exhibited higher reactivity and improved combustion performance.The measured flame propagation rate(v=20.6 mm/s),average combustion wave temperature(T_(max)=1567.0°C)and maximum temperature rise rate(γ_(t)=1633.6°C/s)of Al/Ni@NA are higher than that of the Al/Ni(v=15.8 mm/s,T_(max)=858.0°C,andγ_(t)=143.5°C/s).The enhancement in combustion properties could be due to presence of the acidic gaseous products from ECs,which could etch the Al_(2)O_(3)shell on the surface of Al particles,and make the inner active Al to be easier transported,so that an intimate and faster intermetallic reaction between Al and Ni would be realized.Furthermore,the morphologies and chemical compositions of the condensed combustion products(CCPs)of Al—Ni@ECs composites were found to be different depending on the types of ECs.The compositions of CCPs are dominated with the Al—Ni intermetallics,combining with a trace amount of Al_(5)O_(6)N and Al_(2)O_(3).
基金Ministry of Education and Science of the Russian Federation(14.613.21.0043)
文摘Six furazano-[3,4-d]-pyridazine-based derivatives as main compounds in solid composite propellants have been investigated.It was shown that the use of some furazano-[3,4-d]-pyridazine-based derivatives as main compounds in solid composite propellants can considerably increase ballistic parameters compared with HMX if the compounds under consideration contain difluoramine groups.And the use of the compounds under consideration may be successful only in the presence of an active binder and 10%-30% of AP or ADN as additional oxidizers.
基金the financial support by Postgraduate Research & Practice Innovation Program from Jiangsu Science and Technology Department under Grant number KYCX19_0320。
文摘Copper azide(CA), as a primary explosive with high energy density, has not been practically used so far because of its high electrostatic sensitivity. The Cu2O@HKUST-1 core-shell structure hybrid material was synthesized by the “bottle around ship” methodology in this research by regulating the dissolution rate of Cu2O and the generation rate of metal-organic framework(MOF) materials. Cu2O@HKUST-1 was carbonized to form a Cu O@porous carbon(CuO@PC) composite material. CuO@PC was synthesized into a copper azide(CA) @PC composite energetic material through a gas-solid phase in-situ azidation reaction.CA is encapsulated in PC framework, which acts as a nanoscale Faraday cage, and its excellent electrical conductivity prevents electrostatic charges from accumulating on the energetic material’s surface. The CA@PC composite energetic material has a CA content of 89.6%, and its electrostatic safety is nearly 30times that of pure CA(1.47 mJ compared to 0.05 mJ). CA@PC delivers an outstanding balance of safety and energy density compared to similar materials.
文摘Measurements were made on the contents of protein, lipid, glycogen (PLG) and water, and on caloric values and amino acids, in muscle of three mudskippers Periophthalmis cantonensis, Scarteiaos viridis and Boleophthalmus pectinirostris collected from Haicang, Xiamen. The essential amino acids (EAA) for these fishes were also studied with radioisotopic trace method. The results showed: (1) The content of each component in tested fish muscles differed slightly, and protein was the most important component making up from 6.685% to 9.891% of the wet weight (about 44.21%-50.45% of dry weight); (2) Energy calculated from the sum of protein, lipid and glycogen in wet muscle was low (<4.3kJ/g) in these fishes, especially in B. pectinirostris (<3.1 kJ/g); the ratios of energy to protein content (E/P) also were low (<39.873 -45.535kJ/g); (3) Seventeen amino acids were determined in these three fishes. The content of the same amino acid (among the seventeen) tested in different species and sexes varied slightly. The amounts of methionine, phenylalanine lysine, arginme, histidine, threonine isoleucine and leucine which are indispensable for the needs of human beings and animals were relative-ly high, accounting for 47.35%-48.06% of the total amino acid content. (4) Leucine, isoleucine, arginme, lysine, phenylalanine, tryptophan, methionine, histidine, threonine, and valine, are essential in the diet of the three mudskippers as the radioisotopic trace method using D-[U-^(14) C]-glucose showed little or no radioactivity was incorporated into these ten amino acids.
基金Ministry of Education and Science of the Russian Federation(14.613.21.0043)
文摘The experimental values of the enthalpy of formation of two isomeric 3,4-and 3,5-dinitro-1-(trinitromethyl)-1H-pyrazoles have been obtained(261.5±5.0and 246.4±6.7kJ/mol for crystalline 3,4-and 3,5-dinitro-1-(trinitromethyl)-1H-pyrazoles,respectively).The ballistic effectiveness of these potential oxidizers in composite solid propellants was studied.It is shown that these two oxidizers may be successfully applied in metal-free compositions or with a small content of metal.For the bottom stage 3,4-dinitro-1-(trinitromethyl)-1H-pyrazole is a bit better than 3,5-dinitro-1-(trinitromethyl)-1H-pyrazole,for the upper stage the both oxidizers show the equal ballistic parameters.These oxidizers allow to create metal-free solid composite propellants with the binder percentage not lower than 19%(volume fraction),with I3spequal to 256.5-257.0sat density equal to 1.72-1.74g/cm^3.
基金supported by National Natural Science Foundation of China(grant No.22005275).
文摘Improved controllability and energy density of ignition agents are of great significance for the devel-opment of energetic composite materials.In this study,droplet microfluidics and emulsification tech-niques were combined to prepare HNS/CL-20 composite microspheres with polyglycidyl azide polymer(GAP)as the binder.The influence of binder content on the morphology of microspheres was investi-gated,and the microspheres were characterized and tested for particle size,crystal structure,thermal decomposition,dispersibility,mechanical sensitivity,combustion behavior and detonation performance.The results showed that microspheres prepared with a binder content of 3%had higher sphericity and particle size uniformity.The microspheres retained the crystal structure of both HNS and CL-20(ε-type).Compared with raw HNS,the microspheres had higher apparent activation energy,better safety per-formance,and good dispersibility.The ignition experiments and detonation performance tests show that HNS/CL-20 composite microspheres have excellent ignition performance,obvious combustion flame,and significant energy release effects,which are expected to achieve high energy and high-speed response of the igniter,thus improving the ignition reliability in special environments or systems.
文摘纳米多孔硅由于其海绵状的孔隙结构,氧化剂很难充分填充,导致多孔硅复合含能材料多为富燃料体系;同时其孔隙率难以调节,无法精确控制氧燃比。针对以上问题,以紧密排列的单层聚苯乙烯微球为模板,通过反应性离子刻蚀(Reaction Ion Etching,RIE)技术结合金属辅助化学刻蚀(Metal-Assisted Chemical Etching,MACE)制备得到了形貌结构可控的多孔硅纳米线,通过控制RIE时间能够精准调节多孔硅复合体系的氧燃比,同时二维线状结构非常有利于氧化剂的高效填充。结果表明,在RIE时间为80s,即硅纳米线直径为150nm左右时,复合含能体系达到最佳化学计量反应平衡,能量输出最佳。同时,选用不同电阻率的硅片制备得到不同结构形貌的硅纳米线,电阻率越低,纳米复合含能体系中的硅纳米线结构越疏松多孔,不仅能够有效缩短传质传热距离,降低反应活化能,有利于增强反应放热;而且能提升燃烧性能,有利于点火,为硅基含能材料的发展提供了新的思路。
