Reinforcing effects of polypropylene on energy absorption and fracturing of cement-based tailings backfill under impact loading

Polypropylene(PP)fiber-reinforced cement-based tailings backfill(FRCTB)is a green compound material with superior crack resistance and has good prospects for application in underground mining.However,FRCTB exhibits susceptibility to dynamic events,such as impact ground pressure and blast vibrations.This paper investigates the energy and crack distribution behavior of FRCTB under dynamic impact,considering the height/diameter(H/D)effect.Split Hopkinson pressure bar,industrial computed tomography scan,and scanning electron microscopy(SEM)experiments were carried out on six types of FRCTB.Laboratory outcomes confirmed fiber aggregation at the bottom of specimens.When H/D was less than 0.8,the proportion of PP fibers distributed along theθangle direction of80°-90°increased.For the total energy,all samples presented similar energy absorption,reflectance,and transmittance.However,a rise in H/D may cause a rise in the energy absorption rate of FRCTB during the peak phase.A positive correlation existed between the average strain rate and absorbed energy per unit volume.The increase in H/D resulted in a decreased crack volume fraction of FRCTB.When the H/D was greater than or equal to 0.7,the maximum crack volume fraction of FRCTB was observed close to the incidence plane.Radial cracks were present only in the FRCTB with an H/D ratio of 0.5.Samples with H/D ratios of 0.5 and 0.6 showed similar distributions of weakly and heavily damaged areas.PP fibers can limit the emergence and expansion of cracks by influencing their path.SEM observations revealed considerable differences in the bonding strengths between fibers and the FRCTB.Fibers that adhered particularly well to the substrate were attracted together with the hydration products adhering to surfaces.These results show that FRCTB is promising as a sustainable and green backfill for determining the design properties of mining with backfill.

Impact response and energy absorption of metallic buffer with entangled wire mesh damper

An innovative metallic buffer consisting of series-connected hat-shaped entangled wire mesh damper(EWMD)and parallel springs are proposed in this work to enhance the reliability of engineering equipment.The impact response and the energy dissipation mechanism of hat-shaped EWMD under different quasi-static compression deformations(2-7 mm)and impact heights(100-200 mm)are investigated using experimental and numerical methods.The results demonstrate distinct stages in the quasi-static mechanical characteristics of hat-shaped EWMD,including stiffness softening,negative stiffness,and stiffness hardening.The loss factor gradually increases with increasing compression deformation before entering the stiffness hardening stage.Under impact loads,the hat-shaped EWMD exhibits optimal impact energy absorption when it enters the negative stiffness stage(150 mm),resulting in the best impact isolation effect of metallic buffer.However,the impact energy absorption significantly decreases when hat-shaped EWMD enters the stiffness hardening stage.Interestingly,quasi-static compression analysis after experiencing different impact loads reveals the disappearance of the negative stiffness phenomenon.Moreover,with increasing impact loads,the stiffness hardening point progressively shifts to an earlier stage.

Compressive property and energy absorption characteristic of interconnected porous Mg-Zn-Y alloys with adjusting Y addition

In this study,interconnected porous Mg-2Zn-xY alloys with different phase compositions were prepared by various Y additions(x=0.4,3,and 6 wt.%)to adjust the compressive properties and energy absorption characteristics.Several characterization methods were then applied to identify the microstructure of the porous Mg-Zn-Y and describe the details of the second phase.Compressive tests were performed at room temperature(RT),200℃,and 300℃to study the impact of the Y addition and testing temperature on the compressive properties of the porous Mg-Zn-Y.The experimental results showed that a high Y content promotes a microstructure refinement and increases the volume fraction of the second phase.When the Y content increases,different Mg-Zn-Y ternary phases appear:I-phase(Mg_(3)Zn_(6)Y),W-phase(Mg_(3)Zn_(3)Y_(2)),and LPSO phase(Mg_(12)ZnY).When the Y content ranges between 0.4%and 6%,the compressive strength increases from 6.30MPa to 9.23 MPa,and the energy absorption capacity increases from 7.33 MJ/m^(3)to 10.97 MJ/m^(3)at RT,which is mainly attributed to the phase composition and volume fraction of the second phase.However,the average energy absorption efficiency is independent of the Y content.In addition,the compressive deformation behaviors of the porous Mg-Zn-Y are altered by the testing temperature.The compressive strength and energy absorption capacity of the porous Mg-Zn-Y decrease due to the softening effect of the high temperature on the struts.The deformation behaviors at different temperatures are finally observed to reflect the failure mechanisms of the struts.

Influence of manufacturing process-induced geometrical defects on the energy absorption capacity of polymer lattice structures

Modern additive manufacturing processes enable fabricating architected cellular materials of complex shape,which can be used for different purposes.Among them,lattice structures are increasingly used in applications requiring a compromise among lightness and suited mechanical properties,like improved energy absorption capacity and specific stiffness-to-weight and strength-to-weight ratios.A dedicated modeling strategy to assess the energy absorption capacity of lattice structures under uni-axial compression loading is presented in this work.The numerical model is developed in a non-linear framework accounting for the strain rate effect on the mechanical responses of the lattice structure.Four geometries,i.e.,cubic body centered cell,octet cell,rhombic-dodecahedron and truncated cuboctahedron 2+,are investigated.Specifically,the influence of the relative density of the representative volume element of each geometry,the strain-rate dependency of the bulk material and of the presence of the manufacturing process-induced geometrical imperfections on the energy absorption capacity of the lattice structure is investigated.The main outcome of this study points out the importance of correctly integrating geometrical imperfections into the modeling strategy when shock absorption applications are aimed for.

Dynamic crushing behaviors and enhanced energy absorption of bio-inspired hierarchical honeycombs with different topologies

In order to pursue good crushing load uniformity and enchance energy absorption efficiency of conventional honeycombs, a kind of bio-inspired hierarchical honeycomb model is proposed by mimicking the arched crab shell structures. Three bio-inspired hierarchical honeycombs(BHHs) with different topologies are designed by replacing each vertex of square honeycombs with smaller arc-shaped structures. The effects of hierarchical topologies and multi-material layout on in-plane dynamic crushings and absorbed-energy capacities of the BHHs are explored based on the explicit finite element(FE) analysis.Different deformation modes can be observed from the BHHs, which mainly depend upon hierarchical topologies and impact velocities. According to energy efficiency method and one-dimensional(1D) shock theory, calculation formulas of densification strains and plateau stresses for the BHHs are derived to characterize the dynamic bearing capacity, which is consistent well with FE results. Compared with conventional honeycombs, the crushing load efficiency and energy absorption capacity of the BHHs can be improved by changing the proper hierarchical topology and multi-material layout. These researches will provide theoretical guidance for innovative design and dynamic response performance controllability of honeycombs.

Geometric Accuracy and Energy Absorption Characteristics of 3D Printed Continuous Ramie Fiber Reinforced Thin-Walled Composite Structures

The application of continuous natural fibers as reinforcement in composite thin-walled structures offers a feasible approach to achieve light weight and high strength while remaining environmentally friendly.In addition,additive manufacturing technology provides a favorable process foundation for its realization.In this study,the printability and energy absorption properties of 3D printed continuous fiber reinforced thin-walled structures with different configurations were investigated.The results suggested that a low printing speed and a proper layer thickness would mitigate the printing defects within the structures.The printing geometry accuracy of the structures could be further improved by rounding the sharp corners with appropriate radii.This study successfully fabricated structures with vari-ous configurations characterized by high geometric accuracy through printing parameters optimization and path smoothing.Moreover,the compressive property and energy absorption characteristics of the structures under quasi-static axial compression were evaluated and compared.It was found that all studied thin-walled structures exhibited progressive folding deformation patterns during compression.In particular,energy absorption process was achieved through the combined damage modes of plastic deformation,fiber pullout and delamination.Furthermore,the com-parison results showed that the hexagonal structure exhibited the best energy absorption performance.The study revealed the structure-mechanical property relationship of 3D printed continuous fiber reinforced composite thin-walled structures through the analysis of multiscale failure characteristics and load response,which is valuable for broadening their applications.

Integrating thermal energy storage and microwave absorption in phase change material-encapsulated core-sheath MoS_(2)@CNTs

Developing advanced nanocomposite integrating solar-driven thermal energy storage and thermal management functional microwave absorption can facilitate the cutting-edge application of phase change materials(PCMs).To conquer this goal,herein,two-dimensional MoS_(2) nanosheets are grown in situ on the surface of one-dimensional CNTs to prepare core-sheath MoS_(2)@CNTs for the encapsulation of paraffin wax(PW).Benefiting from the synergistic enhancement photothermal effect of MoS_(2) and CNTs,MoS_(2)@CNTs is capable of efficiently trapping photons and quickly transporting phonons,thus yielding a high solar-thermal energy conversion and storage efficiency of 94.97%.Meanwhile,PW/MoS_(2)@CNTs composite PCMs exhibit a high phase change enthalpy of 101.60 J/g and excellent lo ng-term thermal storage durability after undergoing multiple heating-cooling cycles.More attractively,PW/MoS_(2)@CNTs composite PCMs realize thermal management functional microwave absorption in heat-related electronic application scenarios,which is superior to the single microwave absorption of traditional materials.The minimum reflection loss(RL) for PW/MoS_(2)@CNTs is-28 dB at 12.91 GHz with a 2.0 mm thickness.This functional integration design provides some insightful references on developing advanced microwave absorbing composite PCMs,holding great potential towards high-efficiency solar energy utilization and thermally managed microwave absorption fields.

Mechanical Properties and Energy Absorption of Integrated AlSi10Mg Shell Structures with BCC Lattice Infill

Shell-infill structures comprise an exterior solid shell and an interior lattice infill,whose closed features yield superior comprehensive mechanical performance and light weight.Additive manufacturing(AM)can ensure the fabrica-tion of complex structures.Although the mechanical behaviors of lattice structures have been extensively studied,the corresponding mechanical performances of integrated-manufactured shell structures with lattice infills should be systematically investigated due to the coupling effect of the exterior shell and lattice infill.This study investigated the mechanical properties and energy absorption of AlSi10Mg shell structures with a body-centered cubic lattice infill fabricated by AM.Quasi-static compressive experiments and corresponding finite element analysis were conducted to investigate the mechanical behavior.In addition,two different finite element modeling methods were compared to determine the appropriate modeling strategy in terms of deformation behavior.A study of different parameters,including lattice diameters and shell thicknesses,was conducted to identify their effect on mechanical performance.The results demonstrate the mechanical advantages of shell-infill structures,in which the exterior shell strengthens the lattice infill by up to 2.3 times in terms of the effective Young’s modulus.Increasing the infill strut diameter can improve the specific energy absorption by up to 1.6 times.

Energy Transfer Dynamics between Carbon Quantum Dots and Molybdenum Disulfide Revealed by Transient Absorption Spectroscopy

Zero-dimensional environmentally friendly carbon quantum dots(CQDs)combined with two-di-mensional materials have a wide range of applications in optoelec-tronic devices.We combined steady-state and transient absorp-tion spectroscopies to study the energy transfer dynamics between CQDs and molybdenum disulfide(MoS_(2)).Transient absorption plots showed photoinduced absorption and stimulated emission features,which involved the intrinsic and defect states of CQDs.Adding MoS_(2)to CQDs solution,the lowest unoccupied molecular orbital of CQDs transferred energy to MoS_(2),which quenched the intrinsic emission at 390 nm.With addition of MoS_(2),CQD-MoS_(2)composites quenched defect emission at 490 nm and upward absorption,which originated from another energy transfer from the defect state.Two energy transfer paths between CQDs and MoS_(2)were efficiently manipulated by changing the concentration of MoS_(2),which laid a foundation for improving device performance.

Energy absorption characteristics of novel high-strength and hightoughness steels used for rock support

Nowadays,the development of novel metallic materials for rock support have attracted research interests since they can significantly improve the deformation and energy absorption capacities of rock bolts.Although previous studies proved the importance and mechanical advantages of utilizing high-strength and high-toughness(HSHT)steels in rock support,there is no systematic analysis to reveal the essential energy absorption parameter and the guidelines for further development of metallic rock support materials.This paper analyzes the energy absorption characteristics of novel HSHT steels(negative Poisson’s ratio(NPR)and twinning-induced plasticity(TWIP)steels)in comparison with conventional rock support materials.A physically based crystal plasticity(CP)model was set up and calibrated to study the effect of strain hardening rate(SHR).Meanwhile,the roles of underlying physical mechanisms,i.e.the dislocation density and twin volume fraction,were studied.The results show that the improvement of energy absorption density(EAD)is essential for further development of rock support materials,besides the increase of energy absorption rate(EAR)for previous development of conventional rock support materials.The increase of EAD requires increases of both strength and deformation capacity of materials.For HSHT steels,the decrease of SHR has a positive effect on the improvement of EAD.In addition,the increase of EAD is followed by the increase of twin volume fraction and the decrease of plastic Poisson’s ratio which can promote deformation plasticity of materials.Meanwhile,the increase of EAR is correlated with the accumulation of dislocation density,which can increase the strength of materials.This paper provides the theoretical basis and guidelines for developing rock support materials in deep underground engineering and other related fields.

A Footpad Structure with Reusable Energy Absorption Capability for Deep Space Exploration Lander:Design and Analysis

The footpad structure of a deep space exploration lander is a critical system that makes the initial contact with the ground,and thereby plays a crucial role in determining the stability and energy absorption characteristics during the impact process.The conventional footpad is typically designed with an aluminum honeycomb structure that dissipates energy through plastic deformation.Nevertheless,its effectiveness in providing cushioning and energy absorption becomes significantly compromised when the structure is crushed,rendering it unusable for reusable landers in the future.This study presents a methodology for designing and evaluating structural energy absorption systems incorporating recoverable strain constraints of shape memory alloys(SMA).The topological configuration of the energy absorbing structure is derived using an equivalent static load method(ESL),and three lightweight footpad designs featuring honeycomb-like Ni-Ti shape memory alloys structures and having variable stiffness skins are proposed.To verify the accuracy of the numerical modelling,a honeycomb-like structure subjected to compression load is modeled and then compared with experimental results.Moreover,the influence of the configurations and thickness distribution of the proposed structures on their energy absorption performance is comprehensively evaluated using finite element simulations.The results demonstrate that the proposed design approach effectively regulates the strain threshold to maintain the SMA within the constraint of maximum recoverable strain,resulting in a structural energy absorption capacity of 362 J/kg with a crushing force efficiency greater than 63%.

Hybrid reinforced thermoset polymer composite in energy absorption tube application:A review

The custom of hybridization fibre composite in energy absorption tube application has gained the attention of structural crashworthiness in composite material industry. Thus, the approach of this review is to understand the effect in hybridization within metal/synthetic fibre composite, synthetic/synthetic fibre composite and nature/synthetic fibre composite as energy absorption tube, which reflects on the energy absorption characteristics and crashworthiness behaviors in previous the study. By way of instance, a wide range of methodology and particular parameter in previous study such as the effect in fibre arrangement, matrix polymer, technique of fabrication, fibre treatment(natural fibre), design in geometry/cross-section and others mechanism of hybrid fibre composite tube are highlighted which to comprehend the capability of the mechanical performance and collapsible behavior as sacrificial structure in high-performance structure applications. Moreover, in the recently studies there have been many of the research regarding structural materials as energy absorption tube has been introduced such as metal/matrix composites, new alloy metals and polymer composites which intended to evaluate the performance of these materials into circumstance in loading and impact characteristic. Therefore, this review article is trying to explore the research articles related to the effect of hybridization fibres and thermoset polymer as reinforcement for energy absorption tube research and expected would provide an information and idea which to expend the knowledge in future study of hybridization effect for energy absorption tube, moreover the development for future potential as new hybrid composite fibre materials from the natural/synthetic fibres reinforced composite material in employing of high-performance energy absorption tube application is still less discover and highlighted.

In-plane crushing behavior and energy absorption design of composite honeycombs

Theoretical analysis and numerical simulation methods were used to study the in-plane crushing behavior of single-cell structures and regular and composite honeycombs.Square,hexagonal,and circular honeycombs were selected as honeycomb layers to establish composite honeycomb models in the form of composite structures and realize the complementary advantages of honeycombs with type Ⅰ and type Ⅱ structures.The effects of honeycomb layer arrangement,plastic collapse strength,relative density,and crushing velocity on the deformation mode,plateau stress,load uniformity,and energy absorption performance of the composite honeycombs were mainly considered.A semi-empirical formula for plateau stress and energy absorption rate per unit mass for the composite honeycombs was developed.The results showed that the arrangement mode of honeycomb layers is an important factor that affects their mechanical properties.Appropriately selecting the arrangement of honeycomb layers and the proportion of honeycomb layers with different structures in a composite honeycomb can effectively improve its load uniformity and control the magnitude of plateau stress and energy absorption capacity.

Energy Absorption Diagrams of Multi-layer Corrugated Boards

Based on the static compression experiments, the compressive stress-strain curve of multi-layer corrugated boards is simplified into three sections of linear elasticity, sub-buckling going with local collapse and densification. By considering the structure factors of multi-layer corrugated boards, the energy absorption model is obtained and characterized by the structure factors of corrugated cell-wall. The model is standardized by the solid modulus and it is universal for corrugated structures of different basis material. In the liner-elastic section, with the increase of the load, the energy absorption per unit volume of multi-layer corrugated boards gradually increases; in the sub-buckling section going with local collapse, the compression resistance of multi-layer corrugated boards goes on under a nearly constant load, but the energy absorption per unit volume rapidly increases with the increase of the compression strain. It is shown as an ascending curve in the energy absorption diagram. In the densification section, the corrugated sandwich core has no energy absorption capability. A good consistency is achieved between theoretical and experimental energy absorption curves. In designing the cushioning package, the cushioning properties can be evaluated by the theoretical model without more experiments. The suggested method to develop the energy absorption diagram for corrugated boards can be used to characterize the cushioning properties and optimize the structures of corrugated sandwich structures.

Compressive and energy absorption properties of closed-cell magnesium foams

The quasi-static compressive mechanical behavior and deformation mechanism of closed-cell magnesium foams were studied, and the ef- fects of the density of magnesium foams on the compressive and energy absorption properties were also discussed. The results show that the compressive process of closed-cell magnesium foams is characterized by three deformation stages： linear elastic stage, collapsing stage and densification stage. At the linear elastic stage, the peak compressive strength （t70） and Young＇s modulus （E0） increase as the density increases Magnesium foams can absorb energy at the collapsing stage. In a certain strain range, the energy absorption capacity also increases as the density of magnesium foams increases.

Vibration absorption of parallel-coupled nonlinear energy sink under shock and harmonic excitations

Nonlinear energy sink(NES)can passively absorb broadband energy from primary oscillators.Proper multiple NESs connected in parallel exhibit superior performance to single-degree-of-freedom(SDOF)NESs.In this work,a linear coupling spring is installed between two parallel NESs so as to expand the application scope of such vibration absorbers.The vibration absorption of the parallel and parallel-coupled NESs and the system response induced by the coupling spring are studied.The results show that the responses of the system exhibit a significant difference when the heavier cubic oscillators in the NESs have lower stiffness and the lighter cubic oscillators have higher stiffness.Moreover,the efficiency of the parallel-coupled NES is higher for medium shocks but lower for small and large shocks than that of the parallel NESs.The parallel-coupled NES also shows superior performance for medium harmonic excitations until higher response branches are induced.The performance of the parallel-coupled NES and the SDOF NES is compared.It is found that,regardless of the chosen SDOF NES parameters,the performance of the parallel-coupled NES is similar or superior to that of the SDOF NES in the entire force range.

Lateral compression and energy absorption of foamed concrete-filled polyethylene circular pipe as yielding layer for high geo-stress soft rock tunnels

Foamed concrete as energy absorption material for high geo-stress soft rock tunnels has been proven to be feasible due to its high compressibility and lightweight.However,the lengthy curing and defoaming problems caused by the cast-in-place method of large-volume foamed concrete remain unsolved.In this study,we propose a novel energy absorber composed of foamed concrete-filled polyethylene(FC-PE)pipe and analyze its deformation and energy absorption capacity via quasi-static lateral compression experiments.Results show that FC-PE pipes exhibit typical three-stage deformation characteristics,comprising the elastic stage,the plastic plateau,and the densification stage.Furthermore,the plateau stress,energy absorption,and specific energy absorption of the specimens are 0.81–1.91 MPa,164–533 J,and 1.4–3.6 J/g,respectively.As the density of the foamed concrete increases,the plateau stress and energy absorption increase significantly.Conversely,the length of the plastic plateau and energy absorption efficiency decrease.Moreover,based on the vertical slice method,progressive compression of core material,and the 6 plastic hinges deformation mechanism of the pipe wall,a theoretical calculation method for effective energy absorption is established and achieves good agreement with experimental results,which is beneficial to the optimization of the composite structure.

Deformation mode and energy absorption of polycrystal-inspired square-cell lattice structures

Lattice structures are widely used in many engineering fields due to their excellent mechanical properties such as high specific strength and high specific energy absorption(SEA)capacity.In this paper,square-cell lattice structures with different lattice orientations are investigated in terms of the deformation modes and the energy absorption(EA)performance.Finite element(FE)simulations of in-plane compression are carried out,and the theoretical models from the energy balance principle are developed for calculating the EA of these lattice structures.Satisfactory agreement is achieved between the FE simulation results and the theoretical results.It indicates that the 30◦oriented lattice has the largest EA capacity.Furthermore,inspired by the polycrystal microstructure of metals,novel structures of bi-crystal lattices and quad-crystal lattices are developed through combining multiple singly oriented lattices together.The results of FE simulations of compression indicate that the EA performances of symmetric lattice bi-crystals and quad-crystals are better than those of the identical lattice polycrystal counterparts.This work confirms the feasibility of designing superior energy absorbers with architected meso-structures from the inspiration of metallurgical concepts and microstructures.

Absorption Range and Energy Shift of Surface Plasmon in Au Monomer and Dimer

The resonance behaviors of local surface plasmon resonance in Au monomer and dimer are characterized sys- temically by electron energy loss spectroscopy in a scanning transmission electron microscope. The measured absorption range is about 20nm larger than the physical size of the Au nanoparticles and the resonance peak energy shows a red shift when the electron beam passes off the nanoparticles. The Au dimer displays similar behaviors. Numerical simulation also reproduces those experimental results.

Mechanical properties and energy absorption properties of aluminum foam-filled square tubes

Longitudinal and transverse mechanical properties and energy absorption properties of foam-filled square tubes under quasi-static loading conditions were studied.The foam-filled thin-walled square tube was fabricated with aluminum tube as its shell and closed-cell Al-Mg alloy foam as its core.The results indicated that the plateau region of the load-displacement curve exhibited a marked fluctuant serration which was clearly related to the formation of folds.The longitudinal deforming mode of foam-filled square tube was the same as that of the empty tube,but the fold number of foam-filled square tube was more than that of the empty tube.The longitudinal compression load and energy absorption value of foam-filled square tube were higher than the sum of that of aluminum foam (alone) and empty tube (alone) due to the interaction between tube and filler.In transverse direction,the compression load and energy absorption ability of foam-filled square tubes were significantly lower than those in longitudinal direction.