Alkali Tolerance of Concrete Internal Curing Agent Based on Sodium Carboxymethyl Starch

Internal curing agents (ICA) based on super absorbent polymer have poor alkali tolerance and reduce the early strength of concrete.An alkali tolerate internal curing agent (CAA-ICA) was designed and prepared by using sodium carboxymethyl starch (CMS) with high hydrophilicity,acrylic acid (AA) containing anionic carboxylic group and acrylamide (AM) containing non-ionic amide group as the main raw materials.The results show that the ratio of CAA-ICA alkali absorption solution is higher than that existing ICA,which solves the low water absorption ratio of the ICA in alkali environment.The water absorption ratio of CAA-ICA in saturated Ca(OH)_(2) solution is 95.8 g·g^(-1),and the alkali tolerance coefficient is 3.4.The application of CAA-ICA in cement-based materials can increase the internal relative humidity and miniaturize the pore structure.The compressive strength of mortar increases up to 12.95%at 28 d,which provids a solution to overcome the reduction of the early strength.

Synthesis of Ionic and Non-Ionic Modified Waterborne Polyurethane Curing Agent

By using HDI and TMP as the main raw materials,polyethylene glycol 400(PEG400)is used as a non-ionic hydrophilic modifier,and sodium hydroxyethyl sulfonate is used as an ionic hydrophilic modifier to synthesize a dual hydrophilic modified polyurethane curing agent.Research revealed that introducing PEG400 for hydrophilic chain segments and sodium hydroxyethyl sulfonate for hydrophilic ionic groups in the polyurethane curing agent component leads to a uniform distribution of hydrophilic components,significantly enhancing compatibility with the aqueous polyol component,and results in excellent film performance.The synthesis process and film were characterized using Fourier transform infrared spectroscopy and high-resolution scanning electron microscopy in the study.

A novel high-efficient P/N/Si-containing APP-based flame retardant with a silane coupling agent in its molecular structure for epoxy resin

A flame retardant containing multiple antiflaming elements usually exhibits high-efficient flame retardancy. Here, a novel P/N/Si-containing ammonium polyphosphate derivative(APTES-APP) is synthesized from ammonium polyphosphate(APP) and silane coupling agent(3-aminopropyl)triethoxysilane(APTES)via cation exchange, which is quite different in the chemical structure from APTES-modified APP for retaining silicon hydroxyls. APTES-APP is highly efficient for the epoxy resin. 8%(mass) APTES-APP imparts excellent flame retardancy to the epoxy resin, with a V-0 rating at the UL-94 test(1.6 mm)and an LOI value of 26%(vol). The peak heat release rate and total smoke production of the flameretardant epoxy resin are decreased by 68.1% and 31.3%, respectively. The synergy of P/N/Si contributes to the well-expanded char residue with a strong and dense surface layer, which is a very good barrier against heat and mass transfer. Besides, there is no significant deterioration in the mechanical properties of flame-retardant epoxy resin thanks to silicon hydroxyls forming hydrogen bonds with epoxy molecules. Meanwhile, other molecules can be grafted onto APTES-APP via these silicon hydroxyls, if needed.Briefly, this work has developed a new strategy for amino silane as flame retardants. In conjunction with a low-cost and simple preparation method, APTES-APP has a promising prospect in the high-performance flame-retardant epoxy.

Synthesis and Characterization of Waterborne Epoxy Curing Agent Modified by Silane

A novel waterborne epoxy curing agent was prepared using 3-glycidoxypropyl trimethoxysilane （GPTMS） as a termination agent of adduct, which was synthesized by triethylene tetramine （TETA） and liquid epoxy resin （E-51）. The effects of the reaction temperature and time on the synthesis process were investigated experimentally. The particle size and the distribution of water dispersion of the curing agent were measured by dynamic light scattering（DLS）. The structure of the products was characterized by Fourier transform infrared spec-trometer （FTIR） and ^1H-nuclear magnetic resonance （^1H NMR）. The properties of the synthesized curing agent and the epoxy resin film cured by it were also measured. The results showed that the appropriate temperature for the synthesis of adduct was at 65-75℃ and the reaction time was 4-5h, and that the suitable reaction temperature of curing agent synthesis was 75-85℃ and the reaction time was 3-4h. When the mass ratios of GPTMS and acetic acid were 3%-5% and 5%-10% respectively, the hardness, water resistance and adhesion of the cured film were improved significantly.

COMPARISON OF THE E44 EPOXY RESINS IN DIFFERENT CONTENTS OF CURING AGENT BY MICROWAVE AND THERMAL CURING METHODS

This paper discusses the fundamental principle of microwave heating, and based on the advantages of microwave heating, use maleic anhydride as curing agent. The technology of microwave curing E44 epoxy resins is investigated, the mechanical properties of cured epoxy resin samples in different contents of curing agent by microwave and thermal curing methods are measured respectively, and then some experimental results for which are obtained. At last, this paper analyses why microwave curing can improve mechanical property of epoxy resin.

Evaluation of the injection and plugging ability of a novel epoxy resin in cement cracks

Sustained casing pressure(SCP)is a crucial issue in the oil and gas production lifecycle.Epoxy resins,exhibiting exceptional compressive strength,ductility,and shear bonding strength,have the potential to form reliable barriers.The injectivity and sealing capacity of the epoxy resin is crucial parameters for the success of shallow remediation operations.This study aimed to develop and assess a novel solid-free resin sealant as an alternative to Portland cement for mitigating fluid leakage.The investigation evaluated the viscosity,compressive strength,and brittleness index of the epoxy resin sealant,as well as its tangential and normal shear strengths in conjunction with casing steel.The flow characteristics and sealing abilities of conventional cement and epoxy resin were comparatively analyzed in cracks.The results showed that the application of a viscosity reducer facilitated control over the curing time of the epoxy resin,ranging from 1.5 to 6 h,and reduced the initial viscosity from 865.53 to 118.71 m Pa,s.The mechanical properties of the epoxy resin initially increased with a rise in curing agent content before experiencing a minor decrease.The epoxy resin containing 30%curing agent exhibited optimal mechanical properties.After a 14-day curing period,the epoxy resin's compressive strength reached81.37 MPa,2.12 times higher than that of cement,whereas the elastic modulus of cement was 2.99 times greater than that of the epoxy resin.The brittleness index of epoxy resin is only 3.42,demonstrating high flexibility and toughness.The tangential and normal shear strengths of the epoxy resin exceeded those of cement by 3.17 and 2.82 times,respectively.In a 0.5 mm-wide crack,the injection pressure of the epoxy resin remained below 0.075 MPa,indicating superior injection and flow capabilities.Conversely,the injection pressure of cement surged dramatically to 2.61 MPa within 5 min.The breakthrough pressure of0.5 PV epoxy resin reached 7.53 MPa,decreasing the crack's permeability to 0.02 D,a mere 9.49%of the permeability observed following cement plugging.Upon sealing a 2 mm-wide crack using epoxy resin,the maximum breakthrough pressure attained 5.47 MPa,3.48 times of cement.These results suggest that epoxy resin sealant can be employed safely and effectively to seal cracks in the cement.

Synthesis and Curing Properties of a Novel Novolac Curing Agent Containing Naphthyl and Dicyclopentadiene Moieties

A novel novolac curing agent containing both naphthalene and dicyclopentadiene (DCPD) moieties was prepared to produce a highly heat-resistant cured polymer network. The chemical structure was characterized using Fourier transform infrared spectroscopy, nuclear magnetic resonance, mass spectrometry, and gel permeation chro-matography analyses. The thermal properties of the resulting polymer from diglycidyl ether of bisphenol A epoxy resin cured with the novel curing agent were evaluated using dynamic mechanical thermal analysis and thermogra-vimetric analysis. Compared with the conventional curing agent, the resulting polymer cured with naphtha-lene/DCPD navolac shows considerable improvement in heat resistant properties such as higher glass transition temperature (Tg) and thermal stability. The result also shows better moisture resistance because of the hydrophobic nature of naphthalene/DCPD structure.

Curing Behavior of Epoxy Asphalt

The curing process of epoxy asphalt was analyzed by Fourier transform infrared （FT-IR） spectroscopy. Effect of curing temperature on viscosity of epoxy asphalt, and changes of mechanical properties with curing time were investigated. The evolution of concentration of epoxy band was followed as a function of the applied curing process.The experimental results indicate that the curing reaction rate of epoxy asphalt is invariable before 70 min at 120 ℃, and it decreases when curing time exceeds 70 min. The viscosity of epoxy asphalt increases slowly with curing time at initial curing stage. But it increases quickly after initial curing stage and the initial curing time decreases as the curing temperature increases, The tensile strength increases slowly at incipient curing stage and increases rapidly when curing time is form 20 min to 70 min. The elongation at break shows a decrease with curing time, but it exceeds 200% after cured.

Cure Kinetics of DGEBA with Hyperbranched Poly(3-hydroxyphenyl) Phosphate as Curing Agent Studied by Non-isothermal DSC

The cure kinetics of diglycidyl ether of bisphenol A （DGEBA） with hyperbranched poly （3-hydroxyphenyl） phosphate（HHPP） as the curing agent was investigated by means of non-isothermal differential scanning calorimetry （DSC） at various heating rates. The results were compared with the corresponding results by using 1,3-dihydroxybenzene（DHB） as a model compound. The results show that HHPP can enhance the cure reaction of DGEBA, resulting in the decrease of the peak temperature of the curing curve as well as the decrease of the activation energy because of the flexible --P--O-- groups in the backbone of HHPP. However, both the activation energy of the cured polymer and the peak temperature of the curing curve are increased with DHB as a curing agent. The cure kinetics of the DGEBA/HHPP system was calculated by using the isoconversional method given by Malek. It was found that the two-parameter autocatalytic model（Sestak-Berggren equation） is the most adequate one to describe the cure kinetics of the studied System at various heating rates. The obtained non-isothermal DSC curves from the experimental data show the results being accordant with those theoretically calculated.

Hot Mixing Behavior and Curing Process of Epoxy Asphalt

A new hot mixed epoxy asphalt system was developed. The reaction process of epoxy resin was characterized by Fourier transform infrared spectroscopy (FTIR). The viscosity was investigated by Brinell viscometer when epoxy resin was mixed with asphalt. The glass transition temperature (Tg), homogeneity, thermal stability and viscoelasticity of epoxy asphalt were analyzed by differential scanning calorimetry (DSC), metallographic microscope, thermogravimetric (TG) and dynamic mechanical analysis (DMA). The results showed that the viscosity of epoxy resin modified asphalt reached 1000 mPa·s for more than 180 minutes at 180 ℃, while the best construction process is mixing at 180 ℃ for 2 hours and curing at 60 ℃ for 4 days. The particle size of asphalt is less than 50 μm. In addition, the mechanical properties of the materials are uniform within the specified pavement thickness.

Curing mechanism of TDE-85/MeTHPA epoxy resin modified by polyurethane

Diglycidyl 4,5-epoxy tetrahydro phthalate/methyl tetrahydrophthalic anhydride （TDE-85/MeTHPA） epoxy resin modified by polyurethane （PU） was prepared with 1,4-butanediol （1,4-BDO）, trimethylol propane （TMP） and polyurethane prepolymer synthesized by polypropylene glycol and toluene diisocynate. Chemical reaction and curing mechanism of this system were discussed by incorporating the results of infra spectrum analysis. The results indicate that the epoxy polymeric network I is obtained by the curing reaction between TDE-85 and MeTHPA, while the PU polymeric network II is obtained by the chain-extended and crosslinking reaction between 1,4-BDO, TMP and polyurethane prepolymer（PUP）. The graft chemical bonds are formed between polymer networks I and II that therefore increase the degree of blend and compatibility between epoxy polymer and PU.

Solidification Efficiency and Mechanism of Conventional Curing Agents for Sewage Sludge Stabilization and Dewatering

One of the challenges faced by sewage sludge treatment and disposal is its higher water content,and how to efficient dewater those hazardous materials properly is welcome in practice. This study stabilized the sewage sludge via the using of conventional curing agents and calcined aluminum salts,and the corresponding dewatering mechanisms and structural changes of the stabilized sludge were further comparable analyzed.Experimental results showed that wollastonite and kaolin exhibit a relative higher dewatering efficiency as compared to other conventional curing agents; however the releasing rate of heavy metals of Cu,Cr,Ni for kaolin solidification and Zn,Pb for wollastonite solidification is higher than the sludge samples solidified by other curing agents. For comparison,the sludge samples solidified by calcined aluminum salts (AS),calcium ash,Mg-based curing agent,tricalcium aluminate( C_3A) show a lower heavy metals leaching potential and unconfined compressive strength. In addition,the economic characteristics and local availability of AS,calcium ash,C_3A and CaO makes it have a broad prospect in extension and application. These findings are of great significance for stabilization and dewatering of sewage sludge.

Curing of Epoxy Resin Induced by Femtosecond Laser Pulse

The possibility of curing of epoxy resin induced by femtosecond laser beam was explored through choosing different initators.Absorption spectroscopy, infrared spectroscopy（IR）,stereomicroscopy and scanning electron microscopy（SEM0 were applied to analyze the structure of epoxy resin systems after irradiation with a femtosecond laser beam.The experimental results show that the epoxy resin systems containing diaryliodonium salts can be cared by irradiation of femtosecond laser pulse,while the systems containing benzoing can not be cured.It is found that diaryliodonium salts decompose under the irradiation of femtosecond lase pulse through multi（two）-photon absorption,initiating the ring-opening polymerization of epoxy resin.And the appearance of cured area has a sheet structure consisting of many tiny lamellar structures.

INFLUENCE OF MOLECULAR STRUCTURES OF SECONDARY AMINE TERMINATED POLY(ESTER-AMINE)S ON THE CURING PERFORMANCE WITH EPOXY RESIN

Five secondary amine terminated poly（ester-amine）s （defined as PEA） with controlled molecular structures were synthesized through reacting excessive piperazine with phthalicdiglycol diacrylate （PDDA） and 1,1,1-trimethylolpropane triacrylate （TMPTA） at a constant secondary amine/acrylate group ratio of 1.5/1 and at different PDDA/TMPTA molar ratios. Both IR and ^1H-NMR spectra indicated that all acrylate groups were consumed in the reaction, based on which the structural parameters were calculated from the ^1H-NMR spectra. With decreasing PDDA/TMPTA ratio, the content of secondary amine, degree of branching, molecular weight, Tg and Td increased accordingly. These polymers were further used as both crosslinkers and flexibilizers for a linear epoxy resin E51 to form cured films under ambient condition. The gel content, relative hardness and Tg of the resulting films increased as PEA molecules changed from linear to highly branching structures. Due to the flexibility of PEA molecules, all the films possessed excellent mechanical performance.

PREPARATION AND PROPERTIES OF THERMOSETTING ACRYLIC COATINGS USING TITANIUM-OXO-CLUSTER AS A CURING AGENT

Thermosetting acrylic coatings were prepared by using carboxyl acid group-containing acrylic oligomer and curing with titanium-oxo-clusters which were first pre-hydrolyzed from titanium n-butoxide.The curing ability of the titanium-oxo-cluster was examined using a microdielectric analytical(DEA)curing monitor,Fourier transformed infrared spectroscopy(FTIR),and Soxhlet extraction experiments,and the properties of the resulted coatings were investigated with pendulum hardness tester,dynamic mechanical analysis(DMA),thermogravimetric analysis(TGA)and ultraviolet-visible spectrometer.The effect of titania-oxo-cluster in leading acrylic oligomers to form thermosetting acrylic coatings was confirmed.An increasing pendulum hardness and modulus of acrylic coatings with increasing titania content was observed, which resulted from the increment of crosslinking degree rather than of the titania content.The thermosetting acrylic/titania coatings also showed better thermal stability and higher UV-blocking properties than those coatings using organic curing agent.

MICRO-PHASE SAEPARATION IN EPOXY RESIN WATERBORNE PARTICLES DURING CURING PROCESS

Sub-micron sized phenolic epoxy resin waterborne particles were prepared by phase inversion emulsification. Micro-phase separation occurred during the curing process at high temperature. The as-prepared samples possessed one glass transition temperature （Tg） and two exothermal processes during DSC heating scannings. After being thermally treated above the exothermal peak temperature, they possessed two glass transition temperatures with the disappearance of exothermal peaks, whilst a core/shell structure was formed. This was likely related with the outward diffusion of reactive oligomers to the outer layer of particles.

Curing Reaction Model of Epoxy Asphalt Binder

In order to understand the strength developing law of the epoxy asphalt mixture,a curing reaction model of the epoxy asphalt binder was proposed based upon the thermokinetic analysis.Given some assumptions,the model was developed by applying the Kissinger law as well as Arrhenius equation,and the differential scanning calorimetry was performed for estimating the model parameters.To monitor the strength development of the epoxy asphalt mixture,a strength test program was employed and then results were compared to those produced from the proposed model.The comparative evaluation shows that a good consistency exists between the outputs from test program and the proposed model,indicating that the proposed model can be used effectively for simulating the curing reaction process for the epoxy asphalt binder and predicting the strength development for the epoxy asphalt mixture.

Kinetic Study of Resin-Curing on Carbon Fiber/Epoxy Resin Composites by Microwave Irradiation

Microwave processing has great potential for improving composite manufacturing such as reduction of curing time, energy requirements and operational costs. In this paper, the effects of microwave irradiation for resin-curing of carbon fiber/epoxy resin composite that was composed of discontinuous carbon fibers of 130 μm or 3 mm were investigated. The mechanical properties of carbon fiber/epoxy resin composite cured by microwave irradiation for 20 min at 120°C were similar to ones of the sample prepared by conventional oven for 180 min at 120°C. Microwavecured carbon fiber/epoxy resin composite had higher glass transition temperature than the one prepared by conventional oven. The relation between curing time and flexural modulus indicated that the curing velocity of microwave-irradiated carbon fiber/epoxy resin composite was 9 times faster than the one prepared by conventional oven. Furthermore, activation energies for resincuring reaction on microwave and conventional-cured carbon fiber/epoxy resin composite were estimated. The resin-curing reaction in carbon fiber/epoxy resin composite was promoted by microwave irradiation.

Statistical deduction and experimental verification on kinetic equations for the curing reactions of epoxy resins/amines

Based on three typical mechanisms (second-order, third-order and competitive mechanisms) for the curing reactions of the epoxy resins with amines, a pair of the kinetic equations (for primary and secondary aminations) was presented to explain the uniformity and relationship among the three different kinetic mechanisms of the reactions. The presented macro-equations were deduced from the kinetic micro-equations by the statistics method. And the constitutive equations were verified by experimental data at different reaction times and temperatures (95°C, 60°C and 39°C), taking diglycidyl ether of bisphenol A (DGEBA) /ethyleneamine (EA) as a model.